ARM: at91: remove NEOCORE 926 board

The board is not available anymore and it seems its use
is very limited.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <abelloni@adeneo-embedded.com>

3 files changed, 0 insertions, 394 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 958358c91af..6071f4c3d65 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -352,12 +352,6 @@ config MACH_USB_A9263
 	  Select this if you are using a Calao Systems USB-A9263.
 	  <http://www.calao-systems.com>
 
-config MACH_NEOCORE926
-	bool "Adeneo NEOCORE926"
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using the Adeneo Neocore 926 board.
-
 endif
 
 # ----------------------------------------------------------
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index b38a1dcb79b..39218ca6d8e 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -66,7 +66,6 @@ obj-$(CONFIG_MACH_AT91SAM9G10EK) += board-sam9261ek.o
 # AT91SAM9263 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
 obj-$(CONFIG_MACH_USB_A9263)	+= board-usb-a926x.o
-obj-$(CONFIG_MACH_NEOCORE926)	+= board-neocore926.o
 
 # AT91SAM9RL board-specific support
 obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
deleted file mode 100644
index bc7a1c4a1f6..00000000000
--- a/arch/arm/mach-at91/board-neocore926.c
+++ /dev/null
@@ -1,387 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-neocore926.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2007 Atmel Corporation
- *  Copyright (C) 2008 ADENEO.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/fb.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-#include <asm/sizes.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init neocore926_init_early(void)
-{
-	/* Initialize processor: 20 MHz crystal */
-	at91_initialize(20000000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata neocore926_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata neocore926_udc_data = {
-	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * ADS7846 Touchscreen
- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-static int ads7843_pendown_state(void)
-{
-	return !at91_get_gpio_value(AT91_PIN_PA15);	/* Touchscreen PENIRQ */
-}
-
-static struct ads7846_platform_data ads_info = {
-	.model			= 7843,
-	.x_min			= 150,
-	.x_max			= 3830,
-	.y_min			= 190,
-	.y_max			= 3830,
-	.vref_delay_usecs	= 100,
-	.x_plate_ohms		= 450,
-	.y_plate_ohms		= 250,
-	.pressure_max		= 15000,
-	.debounce_max		= 1,
-	.debounce_rep		= 0,
-	.debounce_tol		= (~0),
-	.get_pendown_state	= ads7843_pendown_state,
-};
-
-static void __init neocore926_add_device_ts(void)
-{
-	at91_set_B_periph(AT91_PIN_PA15, 1);	/* External IRQ1, with pullup */
-	at91_set_gpio_input(AT91_PIN_PC13, 1);	/* Touchscreen BUSY signal */
-}
-#else
-static void __init neocore926_add_device_ts(void) {}
-#endif
-
-/*
- * SPI devices.
- */
-static struct spi_board_info neocore926_spi_devices[] = {
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-	{
-		.modalias	= "ads7846",
-		.chip_select	= 1,
-		.max_speed_hz	= 125000 * 16,
-		.bus_num	= 0,
-		.platform_data	= &ads_info,
-		.irq		= NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
-	},
-#endif
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata neocore926_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PE18,
-		.wp_pin		= AT91_PIN_PE19,
-	},
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata neocore926_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PE31,
-	.is_rmii	= 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata neocore926_nand_partition[] = {
-	{
-		.name	= "Linux Kernel",	/* "Partition 1", */
-		.offset	= 0,
-		.size	= SZ_8M,
-	},
-	{
-		.name	= "Filesystem",		/* "Partition 2", */
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= SZ_32M,
-	},
-	{
-		.name	= "Free",		/* "Partition 3", */
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata neocore926_nand_data = {
-	.ale			= 21,
-	.cle			= 22,
-	.rdy_pin		= AT91_PIN_PB19,
-	.rdy_pin_active_low	= 1,
-	.enable_pin		= AT91_PIN_PD15,
-	.ecc_mode		= NAND_ECC_SOFT,
-	.parts			= neocore926_nand_partition,
-	.num_parts		= ARRAY_SIZE(neocore926_nand_partition),
-	.det_pin		= -EINVAL,
-};
-
-static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 6,
-	.write_cycle		= 6,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 2,
-};
-
-static void __init neocore926_add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &neocore926_nand_smc_config);
-
-	at91_add_device_nand(&neocore926_nand_data);
-}
-
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static struct fb_videomode at91_tft_vga_modes[] = {
-	{
-		.name		= "TX09D50VM1CCA @ 60",
-		.refresh	= 60,
-		.xres		= 240,		.yres		= 320,
-		.pixclock	= KHZ2PICOS(5000),
-
-		.left_margin	= 1,		.right_margin	= 33,
-		.upper_margin	= 1,		.lower_margin	= 0,
-		.hsync_len	= 5,		.vsync_len	= 1,
-
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-		.vmode		= FB_VMODE_NONINTERLACED,
-	},
-};
-
-static struct fb_monspecs at91fb_default_monspecs = {
-	.manufacturer	= "HIT",
-	.monitor	= "TX09D70VM1CCA",
-
-	.modedb		= at91_tft_vga_modes,
-	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
-	.hfmin		= 15000,
-	.hfmax		= 64000,
-	.vfmin		= 50,
-	.vfmax		= 150,
-};
-
-#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
-					| ATMEL_LCDC_DISTYPE_TFT \
-					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-static void at91_lcdc_power_control(int on)
-{
-	at91_set_gpio_value(AT91_PIN_PA30, on);
-}
-
-/* Driver datas */
-static struct atmel_lcdfb_info __initdata neocore926_lcdc_data = {
-	.lcdcon_is_backlight		= true,
-	.default_bpp			= 16,
-	.default_dmacon			= ATMEL_LCDC_DMAEN,
-	.default_lcdcon2		= AT91SAM9263_DEFAULT_LCDCON2,
-	.default_monspecs		= &at91fb_default_monspecs,
-	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
-	.guard_time			= 1,
-	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB555,
-};
-
-#else
-static struct atmel_lcdfb_info __initdata neocore926_lcdc_data;
-#endif
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button neocore926_buttons[] = {
-	{	/* BP1, "leftclic" */
-		.code		= BTN_LEFT,
-		.gpio		= AT91_PIN_PC5,
-		.active_low	= 1,
-		.desc		= "left_click",
-		.wakeup		= 1,
-	},
-	{	/* BP2, "rightclic" */
-		.code		= BTN_RIGHT,
-		.gpio		= AT91_PIN_PC4,
-		.active_low	= 1,
-		.desc		= "right_click",
-		.wakeup		= 1,
-	},
-};
-
-static struct gpio_keys_platform_data neocore926_button_data = {
-	.buttons	= neocore926_buttons,
-	.nbuttons	= ARRAY_SIZE(neocore926_buttons),
-};
-
-static struct platform_device neocore926_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &neocore926_button_data,
-	}
-};
-
-static void __init neocore926_add_device_buttons(void)
-{
-	at91_set_GPIO_periph(AT91_PIN_PC5, 0);	/* left button */
-	at91_set_deglitch(AT91_PIN_PC5, 1);
-	at91_set_GPIO_periph(AT91_PIN_PC4, 0);	/* right button */
-	at91_set_deglitch(AT91_PIN_PC4, 1);
-
-	platform_device_register(&neocore926_button_device);
-}
-#else
-static void __init neocore926_add_device_buttons(void) {}
-#endif
-
-
-/*
- * AC97
- */
-static struct ac97c_platform_data neocore926_ac97_data = {
-	.reset_pin	= AT91_PIN_PA13,
-};
-
-
-static void __init neocore926_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-
-	/* USB Host */
-	at91_add_device_usbh(&neocore926_usbh_data);
-
-	/* USB Device */
-	at91_add_device_udc(&neocore926_udc_data);
-
-	/* SPI */
-	at91_set_gpio_output(AT91_PIN_PE20, 1);		/* select spi0 clock */
-	at91_add_device_spi(neocore926_spi_devices, ARRAY_SIZE(neocore926_spi_devices));
-
-	/* Touchscreen */
-	neocore926_add_device_ts();
-
-	/* MMC */
-	at91_add_device_mci(0, &neocore926_mci0_data);
-
-	/* Ethernet */
-	at91_add_device_eth(&neocore926_macb_data);
-
-	/* NAND */
-	neocore926_add_device_nand();
-
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-
-	/* LCD Controller */
-	at91_add_device_lcdc(&neocore926_lcdc_data);
-
-	/* Push Buttons */
-	neocore926_add_device_buttons();
-
-	/* AC97 */
-	at91_add_device_ac97(&neocore926_ac97_data);
-}
-
-MACHINE_START(NEOCORE926, "ADENEO NEOCORE 926")
-	/* Maintainer: ADENEO */
-	.timer		= &at91sam926x_timer,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= neocore926_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= neocore926_board_init,
-MACHINE_END