at91: remove MTD_NAND_ATMEL_BUSWIDTH_16 option

no board configure it as 'n' and it's an issue to merge all defconfigs
in one

On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).

so will pass it via system_rev

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>

9 files changed, 39 insertions, 54 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 2d299bf5d72..8cbc3aae6c6 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -3,9 +3,6 @@ if ARCH_AT91
 config HAVE_AT91_DATAFLASH_CARD
 	bool
 
-config HAVE_NAND_ATMEL_BUSWIDTH_16
-	bool
-
 config HAVE_AT91_USART3
 	bool
 
@@ -209,7 +206,6 @@ comment "AT91SAM9260 / AT91SAM9XE Board Type"
 config MACH_AT91SAM9260EK
 	bool "Atmel AT91SAM9260-EK / AT91SAM9XE Evaluation Kit"
 	select HAVE_AT91_DATAFLASH_CARD
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit
 	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933>
@@ -270,7 +266,6 @@ comment "AT91SAM9261 Board Type"
 config MACH_AT91SAM9261EK
 	bool "Atmel AT91SAM9261-EK Evaluation Kit"
 	select HAVE_AT91_DATAFLASH_CARD
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit.
 	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3820>
@@ -286,7 +281,6 @@ comment "AT91SAM9G10 Board Type"
 config MACH_AT91SAM9G10EK
 	bool "Atmel AT91SAM9G10-EK Evaluation Kit"
 	select HAVE_AT91_DATAFLASH_CARD
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT91SAM9G10-EK Evaluation Kit.
 	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4588>
@@ -302,7 +296,6 @@ comment "AT91SAM9263 Board Type"
 config MACH_AT91SAM9263EK
 	bool "Atmel AT91SAM9263-EK Evaluation Kit"
 	select HAVE_AT91_DATAFLASH_CARD
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit.
 	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057>
@@ -343,7 +336,6 @@ comment "AT91SAM9G20 Board Type"
 config MACH_AT91SAM9G20EK
 	bool "Atmel AT91SAM9G20-EK Evaluation Kit"
 	select HAVE_AT91_DATAFLASH_CARD
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit
 	  that embeds only one SD/MMC slot.
@@ -351,7 +343,6 @@ config MACH_AT91SAM9G20EK
 config MACH_AT91SAM9G20EK_2MMC
 	depends on MACH_AT91SAM9G20EK
 	bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots"
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
 	  with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and
@@ -416,7 +407,6 @@ comment "AT91SAM9G45 Board Type"
 
 config MACH_AT91SAM9M10G45EK
 	bool "Atmel AT91SAM9M10G45-EK Evaluation Kits"
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit.
 	  "ES" at the end of the name means that this board is an
@@ -433,7 +423,6 @@ comment "AT91CAP9 Board Type"
 config MACH_AT91CAP9ADK
 	bool "Atmel AT91CAP9A-DK Evaluation Kit"
 	select HAVE_AT91_DATAFLASH_CARD
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT91CAP9A-DK Evaluation Kit.
 	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4138>
@@ -450,7 +439,6 @@ config MACH_AT572D940HFEB
 	bool "AT572D940HF-EK"
 	depends on ARCH_AT572D940HF
 	select HAVE_AT91_DATAFLASH_CARD
-	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT572D940HF-EK evaluation kit.
 	  <http://www.atmel.com/products/diopsis/default.asp>
@@ -483,13 +471,6 @@ config MTD_AT91_DATAFLASH_CARD
 	help
 	  Enable support for the DataFlash card.
 
-config MTD_NAND_ATMEL_BUSWIDTH_16
-	bool "Enable 16-bit data bus interface to NAND flash"
-	depends on HAVE_NAND_ATMEL_BUSWIDTH_16
-	help
-	  On AT91SAM926x boards both types of NAND flash can be present
-	  (8 and 16 bit data bus width).
-
 # ----------------------------------------------------------
 
 comment "AT91 Feature Selections"
diff --git a/arch/arm/mach-at91/board-at572d940hf_ek.c b/arch/arm/mach-at91/board-at572d940hf_ek.c
index 3929f1c9e4e..096b99f4b1f 100644
--- a/arch/arm/mach-at91/board-at572d940hf_ek.c
+++ b/arch/arm/mach-at91/board-at572d940hf_ek.c
@@ -41,6 +41,7 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/system_rev.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -216,11 +217,6 @@ static struct atmel_nand_data __initdata eb_nand_data = {
 /*	.rdy_pin	= AT91_PIN_PC16, */
 	.enable_pin	= AT91_PIN_PA15,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
 static struct sam9_smc_config __initdata eb_nand_smc_config = {
@@ -243,6 +239,7 @@ static struct sam9_smc_config __initdata eb_nand_smc_config = {
 
 static void __init eb_add_device_nand(void)
 {
+	ek_nand_data.bus_width_16 = !board_have_nand_8bit();
 	/* setup bus-width (8 or 16) */
 	if (eb_nand_data.bus_width_16)
 		eb_nand_smc_config.mode |= AT91_SMC_DBW_16;
diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c
index e7274440ead..96010d4e15a 100644
--- a/arch/arm/mach-at91/board-cap9adk.c
+++ b/arch/arm/mach-at91/board-cap9adk.c
@@ -44,6 +44,7 @@
 #include <mach/gpio.h>
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/system_rev.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -187,11 +188,6 @@ static struct atmel_nand_data __initdata cap9adk_nand_data = {
 //	.rdy_pin	= ... not connected
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
 static struct sam9_smc_config __initdata cap9adk_nand_smc_config = {
@@ -219,6 +215,7 @@ static void __init cap9adk_add_device_nand(void)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
 
+	cap9adk_nand_data.bus_width_16 = !board_have_nand_8bit();
 	/* setup bus-width (8 or 16) */
 	if (cap9adk_nand_data.bus_width_16)
 		cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_16;
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index de1816e0e1d..fdfa144cbe7 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -44,6 +44,7 @@
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
+#include <mach/system_rev.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -191,11 +192,6 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -218,6 +214,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 
 static void __init ek_add_device_nand(void)
 {
+	ek_nand_data.bus_width_16 = !board_have_nand_8bit();
 	/* setup bus-width (8 or 16) */
 	if (ek_nand_data.bus_width_16)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 14acc901e24..c2773b5f2ee 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -48,6 +48,7 @@
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
+#include <mach/system_rev.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -197,11 +198,6 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC15,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -224,6 +220,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 
 static void __init ek_add_device_nand(void)
 {
+	ek_nand_data.bus_width_16 = !board_have_nand_8bit();
 	/* setup bus-width (8 or 16) */
 	if (ek_nand_data.bus_width_16)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index bfe490df58b..1dabc0ae56c 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -47,6 +47,7 @@
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
+#include <mach/system_rev.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -198,11 +199,6 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -225,6 +221,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 
 static void __init ek_add_device_nand(void)
 {
+	ek_nand_data.bus_width_16 = !board_have_nand_8bit();
 	/* setup bus-width (8 or 16) */
 	if (ek_nand_data.bus_width_16)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index ca8198b3c16..d13acd5c92f 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -43,6 +43,7 @@
 #include <mach/board.h>
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/system_rev.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -175,11 +176,6 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -202,6 +198,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 
 static void __init ek_add_device_nand(void)
 {
+	ek_nand_data.bus_width_16 = !board_have_nand_8bit();
 	/* setup bus-width (8 or 16) */
 	if (ek_nand_data.bus_width_16)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index 6c999dbd2bc..49d6849f0cc 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -41,6 +41,7 @@
 #include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
+#include <mach/system_rev.h>
 
 #include "sam9_smc.h"
 #include "generic.h"
@@ -155,11 +156,6 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -182,6 +178,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 
 static void __init ek_add_device_nand(void)
 {
+	ek_nand_data.bus_width_16 = !board_have_nand_8bit();
 	/* setup bus-width (8 or 16) */
 	if (ek_nand_data.bus_width_16)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
diff --git a/arch/arm/mach-at91/include/mach/system_rev.h b/arch/arm/mach-at91/include/mach/system_rev.h
new file mode 100644
index 00000000000..b855ee75f72
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/system_rev.h
@@ -0,0 +1,25 @@
+/*
+ * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2 only
+ */
+
+#ifndef __ARCH_SYSTEM_REV_H__
+#define __ARCH_SYSTEM_REV_H__
+
+/*
+ * board revision encoding
+ * mach specific
+ * the 16-31 bit are reserved for at91 generic information
+ *
+ * bit 31:
+ *	0 => nand 16 bit
+ *	1 => nand 8 bit
+ */
+#define BOARD_HAVE_NAND_8BIT	(1 << 31)
+static int inline board_have_nand_8bit(void)
+{
+	return system_rev & BOARD_HAVE_NAND_8BIT;
+}
+
+#endif /* __ARCH_SYSTEM_REV_H__ */