Merge branch 'for-rmk' of git://source.mvista.com/git/linux-davinci-2.6.git

Merge branch 'davinci' into devel

9 files changed, 614 insertions, 150 deletions

diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile
index 99ac2e55774..4dc458597f4 100644
--- a/arch/arm/mach-davinci/Makefile
+++ b/arch/arm/mach-davinci/Makefile
@@ -5,7 +5,7 @@
 
 # Common objects
 obj-y 			:= time.o irq.o clock.o serial.o io.o id.o psc.o \
-			   gpio.o mux.o
+			   gpio.o mux.o devices.o usb.o
 
 # Board specific
 obj-$(CONFIG_MACH_DAVINCI_EVM)  += board-evm.o
diff --git a/arch/arm/mach-davinci/board-evm.c b/arch/arm/mach-davinci/board-evm.c
index 41f3cc4ac4a..a957d239a68 100644
--- a/arch/arm/mach-davinci/board-evm.c
+++ b/arch/arm/mach-davinci/board-evm.c
@@ -13,6 +13,13 @@
 #include <linux/init.h>
 #include <linux/dma-mapping.h>
 #include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+
+#include <linux/i2c.h>
+#include <linux/i2c/pcf857x.h>
+#include <linux/i2c/at24.h>
+
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
@@ -20,13 +27,14 @@
 
 #include <asm/setup.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/mach/flash.h>
 
+#include <mach/hardware.h>
 #include <mach/common.h>
+#include <mach/i2c.h>
 
 /* other misc. init functions */
 void __init davinci_psc_init(void);
@@ -34,10 +42,10 @@ void __init davinci_irq_init(void);
 void __init davinci_map_common_io(void);
 void __init davinci_init_common_hw(void);
 
-/* NOR Flash base address set to CS0 by default */
-#define NOR_FLASH_PHYS 0x02000000
+#if defined(CONFIG_MTD_PHYSMAP) || \
+    defined(CONFIG_MTD_PHYSMAP_MODULE)
 
-static struct mtd_partition davinci_evm_partitions[] = {
+static struct mtd_partition davinci_evm_norflash_partitions[] = {
 	/* bootloader (U-Boot, etc) in first 4 sectors */
 	{
 		.name		= "bootloader",
@@ -68,32 +76,323 @@ static struct mtd_partition davinci_evm_partitions[] = {
 	}
 };
 
-static struct physmap_flash_data davinci_evm_flash_data = {
+static struct physmap_flash_data davinci_evm_norflash_data = {
 	.width		= 2,
-	.parts		= davinci_evm_partitions,
-	.nr_parts	= ARRAY_SIZE(davinci_evm_partitions),
+	.parts		= davinci_evm_norflash_partitions,
+	.nr_parts	= ARRAY_SIZE(davinci_evm_norflash_partitions),
 };
 
 /* NOTE: CFI probe will correctly detect flash part as 32M, but EMIF
  * limits addresses to 16M, so using addresses past 16M will wrap */
-static struct resource davinci_evm_flash_resource = {
-	.start		= NOR_FLASH_PHYS,
-	.end		= NOR_FLASH_PHYS + SZ_16M - 1,
+static struct resource davinci_evm_norflash_resource = {
+	.start		= DAVINCI_ASYNC_EMIF_DATA_CE0_BASE,
+	.end		= DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1,
 	.flags		= IORESOURCE_MEM,
 };
 
-static struct platform_device davinci_evm_flash_device = {
+static struct platform_device davinci_evm_norflash_device = {
 	.name		= "physmap-flash",
 	.id		= 0,
 	.dev		= {
-		.platform_data	= &davinci_evm_flash_data,
+		.platform_data	= &davinci_evm_norflash_data,
 	},
 	.num_resources	= 1,
-	.resource	= &davinci_evm_flash_resource,
+	.resource	= &davinci_evm_norflash_resource,
+};
+
+#endif
+
+#if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
+    defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE)
+
+static struct resource ide_resources[] = {
+	{
+		.start          = DAVINCI_CFC_ATA_BASE,
+		.end            = DAVINCI_CFC_ATA_BASE + 0x7ff,
+		.flags          = IORESOURCE_MEM,
+	},
+	{
+		.start          = IRQ_IDE,
+		.end            = IRQ_IDE,
+		.flags          = IORESOURCE_IRQ,
+	},
+};
+
+static u64 ide_dma_mask = DMA_32BIT_MASK;
+
+static struct platform_device ide_dev = {
+	.name           = "palm_bk3710",
+	.id             = -1,
+	.resource       = ide_resources,
+	.num_resources  = ARRAY_SIZE(ide_resources),
+	.dev = {
+		.dma_mask		= &ide_dma_mask,
+		.coherent_dma_mask      = DMA_32BIT_MASK,
+	},
+};
+
+#endif
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * I2C GPIO expanders
+ */
+
+#define PCF_Uxx_BASE(x)	(DAVINCI_N_GPIO + ((x) * 8))
+
+
+/* U2 -- LEDs */
+
+static struct gpio_led evm_leds[] = {
+	{ .name = "DS8", .active_low = 1,
+		.default_trigger = "heartbeat", },
+	{ .name = "DS7", .active_low = 1, },
+	{ .name = "DS6", .active_low = 1, },
+	{ .name = "DS5", .active_low = 1, },
+	{ .name = "DS4", .active_low = 1, },
+	{ .name = "DS3", .active_low = 1, },
+	{ .name = "DS2", .active_low = 1,
+		.default_trigger = "mmc0", },
+	{ .name = "DS1", .active_low = 1,
+		.default_trigger = "ide-disk", },
+};
+
+static const struct gpio_led_platform_data evm_led_data = {
+	.num_leds	= ARRAY_SIZE(evm_leds),
+	.leds		= evm_leds,
+};
+
+static struct platform_device *evm_led_dev;
+
+static int
+evm_led_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
+{
+	struct gpio_led *leds = evm_leds;
+	int status;
+
+	while (ngpio--) {
+		leds->gpio = gpio++;
+		leds++;
+	}
+
+	/* what an extremely annoying way to be forced to handle
+	 * device unregistration ...
+	 */
+	evm_led_dev = platform_device_alloc("leds-gpio", 0);
+	platform_device_add_data(evm_led_dev,
+			&evm_led_data, sizeof evm_led_data);
+
+	evm_led_dev->dev.parent = &client->dev;
+	status = platform_device_add(evm_led_dev);
+	if (status < 0) {
+		platform_device_put(evm_led_dev);
+		evm_led_dev = NULL;
+	}
+	return status;
+}
+
+static int
+evm_led_teardown(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
+{
+	if (evm_led_dev) {
+		platform_device_unregister(evm_led_dev);
+		evm_led_dev = NULL;
+	}
+	return 0;
+}
+
+static struct pcf857x_platform_data pcf_data_u2 = {
+	.gpio_base	= PCF_Uxx_BASE(0),
+	.setup		= evm_led_setup,
+	.teardown	= evm_led_teardown,
+};
+
+
+/* U18 - A/V clock generator and user switch */
+
+static int sw_gpio;
+
+static ssize_t
+sw_show(struct device *d, struct device_attribute *a, char *buf)
+{
+	char *s = gpio_get_value_cansleep(sw_gpio) ? "on\n" : "off\n";
+
+	strcpy(buf, s);
+	return strlen(s);
+}
+
+static DEVICE_ATTR(user_sw, S_IRUGO, sw_show, NULL);
+
+static int
+evm_u18_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
+{
+	int	status;
+
+	/* export dip switch option */
+	sw_gpio = gpio + 7;
+	status = gpio_request(sw_gpio, "user_sw");
+	if (status == 0)
+		status = gpio_direction_input(sw_gpio);
+	if (status == 0)
+		status = device_create_file(&client->dev, &dev_attr_user_sw);
+	else
+		gpio_free(sw_gpio);
+	if (status != 0)
+		sw_gpio = -EINVAL;
+
+	/* audio PLL:  48 kHz (vs 44.1 or 32), single rate (vs double) */
+	gpio_request(gpio + 3, "pll_fs2");
+	gpio_direction_output(gpio + 3, 0);
+
+	gpio_request(gpio + 2, "pll_fs1");
+	gpio_direction_output(gpio + 2, 0);
+
+	gpio_request(gpio + 1, "pll_sr");
+	gpio_direction_output(gpio + 1, 0);
+
+	return 0;
+}
+
+static int
+evm_u18_teardown(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
+{
+	gpio_free(gpio + 1);
+	gpio_free(gpio + 2);
+	gpio_free(gpio + 3);
+
+	if (sw_gpio > 0) {
+		device_remove_file(&client->dev, &dev_attr_user_sw);
+		gpio_free(sw_gpio);
+	}
+	return 0;
+}
+
+static struct pcf857x_platform_data pcf_data_u18 = {
+	.gpio_base	= PCF_Uxx_BASE(1),
+	.n_latch	= (1 << 3) | (1 << 2) | (1 << 1),
+	.setup		= evm_u18_setup,
+	.teardown	= evm_u18_teardown,
 };
 
+
+/* U35 - various I/O signals used to manage USB, CF, ATA, etc */
+
+static int
+evm_u35_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
+{
+	/* p0 = nDRV_VBUS (initial:  don't supply it) */
+	gpio_request(gpio + 0, "nDRV_VBUS");
+	gpio_direction_output(gpio + 0, 1);
+
+	/* p1 = VDDIMX_EN */
+	gpio_request(gpio + 1, "VDDIMX_EN");
+	gpio_direction_output(gpio + 1, 1);
+
+	/* p2 = VLYNQ_EN */
+	gpio_request(gpio + 2, "VLYNQ_EN");
+	gpio_direction_output(gpio + 2, 1);
+
+	/* p3 = n3V3_CF_RESET (initial: stay in reset) */
+	gpio_request(gpio + 3, "nCF_RESET");
+	gpio_direction_output(gpio + 3, 0);
+
+	/* (p4 unused) */
+
+	/* p5 = 1V8_WLAN_RESET (initial: stay in reset) */
+	gpio_request(gpio + 5, "WLAN_RESET");
+	gpio_direction_output(gpio + 5, 1);
+
+	/* p6 = nATA_SEL (initial: select) */
+	gpio_request(gpio + 6, "nATA_SEL");
+	gpio_direction_output(gpio + 6, 0);
+
+	/* p7 = nCF_SEL (initial: deselect) */
+	gpio_request(gpio + 7, "nCF_SEL");
+	gpio_direction_output(gpio + 7, 1);
+
+	return 0;
+}
+
+static int
+evm_u35_teardown(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
+{
+	gpio_free(gpio + 7);
+	gpio_free(gpio + 6);
+	gpio_free(gpio + 5);
+	gpio_free(gpio + 3);
+	gpio_free(gpio + 2);
+	gpio_free(gpio + 1);
+	gpio_free(gpio + 0);
+	return 0;
+}
+
+static struct pcf857x_platform_data pcf_data_u35 = {
+	.gpio_base	= PCF_Uxx_BASE(2),
+	.setup		= evm_u35_setup,
+	.teardown	= evm_u35_teardown,
+};
+
+/*----------------------------------------------------------------------*/
+
+/* Most of this EEPROM is unused, but U-Boot uses some data:
+ *  - 0x7f00, 6 bytes Ethernet Address
+ *  - 0x0039, 1 byte NTSC vs PAL (bit 0x80 == PAL)
+ *  - ... newer boards may have more
+ */
+static struct at24_platform_data eeprom_info = {
+	.byte_len	= (256*1024) / 8,
+	.page_size	= 64,
+	.flags		= AT24_FLAG_ADDR16,
+};
+
+static struct i2c_board_info __initdata i2c_info[] =  {
+	{
+		I2C_BOARD_INFO("pcf8574", 0x38),
+		.platform_data	= &pcf_data_u2,
+	},
+	{
+		I2C_BOARD_INFO("pcf8574", 0x39),
+		.platform_data	= &pcf_data_u18,
+	},
+	{
+		I2C_BOARD_INFO("pcf8574", 0x3a),
+		.platform_data	= &pcf_data_u35,
+	},
+	{
+		I2C_BOARD_INFO("24c256", 0x50),
+		.platform_data	= &eeprom_info,
+	},
+	/* ALSO:
+	 * - tvl320aic33 audio codec (0x1b)
+	 * - msp430 microcontroller (0x23)
+	 * - tvp5146 video decoder (0x5d)
+	 */
+};
+
+/* The msp430 uses a slow bitbanged I2C implementation (ergo 20 KHz),
+ * which requires 100 usec of idle bus after i2c writes sent to it.
+ */
+static struct davinci_i2c_platform_data i2c_pdata = {
+	.bus_freq	= 20 /* kHz */,
+	.bus_delay	= 100 /* usec */,
+};
+
+static void __init evm_init_i2c(void)
+{
+	davinci_init_i2c(&i2c_pdata);
+	i2c_register_board_info(1, i2c_info, ARRAY_SIZE(i2c_info));
+}
+
 static struct platform_device *davinci_evm_devices[] __initdata = {
-	&davinci_evm_flash_device,
+#if defined(CONFIG_MTD_PHYSMAP) || \
+    defined(CONFIG_MTD_PHYSMAP_MODULE)
+	&davinci_evm_norflash_device,
+#endif
+#if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
+    defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE)
+	&ide_dev,
+#endif
 };
 
 static void __init
@@ -106,13 +405,21 @@ static __init void davinci_evm_init(void)
 {
 	davinci_psc_init();
 
-#if defined(CONFIG_BLK_DEV_DAVINCI) || defined(CONFIG_BLK_DEV_DAVINCI_MODULE)
+#if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
+    defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE)
+#if defined(CONFIG_MTD_PHYSMAP) || \
+    defined(CONFIG_MTD_PHYSMAP_MODULE)
 	printk(KERN_WARNING "WARNING: both IDE and NOR flash are enabled, "
 	       "but share pins.\n\t Disable IDE for NOR support.\n");
 #endif
+#endif
 
 	platform_add_devices(davinci_evm_devices,
 			     ARRAY_SIZE(davinci_evm_devices));
+	evm_init_i2c();
+
+	/* irlml6401 sustains over 3A, switches 5V in under 8 msec */
+	setup_usb(500, 8);
 }
 
 static __init void davinci_evm_irq_init(void)
@@ -124,7 +431,7 @@ static __init void davinci_evm_irq_init(void)
 MACHINE_START(DAVINCI_EVM, "DaVinci EVM")
 	/* Maintainer: MontaVista Software <source@mvista.com> */
 	.phys_io      = IO_PHYS,
-	.io_pg_offst  = (io_p2v(IO_PHYS) >> 18) & 0xfffc,
+	.io_pg_offst  = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
 	.boot_params  = (DAVINCI_DDR_BASE + 0x100),
 	.map_io	      = davinci_evm_map_io,
 	.init_irq     = davinci_evm_irq_init,
diff --git a/arch/arm/mach-davinci/devices.c b/arch/arm/mach-davinci/devices.c
new file mode 100644
index 00000000000..3d4b1de8f89
--- /dev/null
+++ b/arch/arm/mach-davinci/devices.c
@@ -0,0 +1,48 @@
+/*
+ * mach-davinci/devices.c
+ *
+ * DaVinci platform device setup/initialization
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+
+#include <asm/mach/map.h>
+
+#include <mach/hardware.h>
+#include <mach/i2c.h>
+
+static struct resource i2c_resources[] = {
+	{
+		.start		= DAVINCI_I2C_BASE,
+		.end		= DAVINCI_I2C_BASE + 0x40,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= IRQ_I2C,
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device davinci_i2c_device = {
+	.name           = "i2c_davinci",
+	.id             = 1,
+	.num_resources	= ARRAY_SIZE(i2c_resources),
+	.resource	= i2c_resources,
+};
+
+void __init davinci_init_i2c(struct davinci_i2c_platform_data *pdata)
+{
+	davinci_i2c_device.dev.platform_data = pdata;
+	(void) platform_device_register(&davinci_i2c_device);
+}
+
diff --git a/arch/arm/mach-davinci/gpio.c b/arch/arm/mach-davinci/gpio.c
index 574cb810a50..b49e9d092aa 100644
--- a/arch/arm/mach-davinci/gpio.c
+++ b/arch/arm/mach-davinci/gpio.c
@@ -1,7 +1,7 @@
 /*
  * TI DaVinci GPIO Support
  *
- * Copyright (c) 2006 David Brownell
+ * Copyright (c) 2006-2007 David Brownell
  * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
  *
  * This program is free software; you can redistribute it and/or modify
@@ -26,47 +26,45 @@
 
 #include <asm/mach/irq.h>
 
-static DEFINE_SPINLOCK(gpio_lock);
-static DECLARE_BITMAP(gpio_in_use, DAVINCI_N_GPIO);
 
-int gpio_request(unsigned gpio, const char *tag)
-{
-	if (gpio >= DAVINCI_N_GPIO)
-		return -EINVAL;
+static DEFINE_SPINLOCK(gpio_lock);
 
-	if (test_and_set_bit(gpio, gpio_in_use))
-		return -EBUSY;
+struct davinci_gpio {
+	struct gpio_chip	chip;
+	struct gpio_controller	*__iomem regs;
+};
 
-	return 0;
-}
-EXPORT_SYMBOL(gpio_request);
+static struct davinci_gpio chips[DIV_ROUND_UP(DAVINCI_N_GPIO, 32)];
 
-void gpio_free(unsigned gpio)
-{
-	if (gpio >= DAVINCI_N_GPIO)
-		return;
-
-	clear_bit(gpio, gpio_in_use);
-}
-EXPORT_SYMBOL(gpio_free);
 
 /* create a non-inlined version */
-static struct gpio_controller *__iomem gpio2controller(unsigned gpio)
+static struct gpio_controller *__iomem __init gpio2controller(unsigned gpio)
 {
 	return __gpio_to_controller(gpio);
 }
 
+
+/*--------------------------------------------------------------------------*/
+
 /*
- * Assuming the pin is muxed as a gpio output, set its output value.
+ * board setup code *MUST* set PINMUX0 and PINMUX1 as
+ * needed, and enable the GPIO clock.
  */
-void __gpio_set(unsigned gpio, int value)
+
+static int davinci_direction_in(struct gpio_chip *chip, unsigned offset)
 {
-	struct gpio_controller *__iomem g = gpio2controller(gpio);
+	struct davinci_gpio *d = container_of(chip, struct davinci_gpio, chip);
+	struct gpio_controller *__iomem g = d->regs;
+	u32 temp;
 
-	__raw_writel(__gpio_mask(gpio), value ? &g->set_data : &g->clr_data);
-}
-EXPORT_SYMBOL(__gpio_set);
+	spin_lock(&gpio_lock);
+	temp = __raw_readl(&g->dir);
+	temp |= (1 << offset);
+	__raw_writel(temp, &g->dir);
+	spin_unlock(&gpio_lock);
 
+	return 0;
+}
 
 /*
  * Read the pin's value (works even if it's set up as output);
@@ -75,61 +73,72 @@ EXPORT_SYMBOL(__gpio_set);
  * Note that changes are synched to the GPIO clock, so reading values back
  * right after you've set them may give old values.
  */
-int __gpio_get(unsigned gpio)
+static int davinci_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	struct gpio_controller *__iomem g = gpio2controller(gpio);
+	struct davinci_gpio *d = container_of(chip, struct davinci_gpio, chip);
+	struct gpio_controller *__iomem g = d->regs;
 
-	return !!(__gpio_mask(gpio) & __raw_readl(&g->in_data));
+	return (1 << offset) & __raw_readl(&g->in_data);
 }
-EXPORT_SYMBOL(__gpio_get);
 
-
-/*--------------------------------------------------------------------------*/
-
-/*
- * board setup code *MUST* set PINMUX0 and PINMUX1 as
- * needed, and enable the GPIO clock.
- */
-
-int gpio_direction_input(unsigned gpio)
+static int
+davinci_direction_out(struct gpio_chip *chip, unsigned offset, int value)
 {
-	struct gpio_controller *__iomem g = gpio2controller(gpio);
+	struct davinci_gpio *d = container_of(chip, struct davinci_gpio, chip);
+	struct gpio_controller *__iomem g = d->regs;
 	u32 temp;
-	u32 mask;
-
-	if (!g)
-		return -EINVAL;
+	u32 mask = 1 << offset;
 
 	spin_lock(&gpio_lock);
-	mask = __gpio_mask(gpio);
 	temp = __raw_readl(&g->dir);
-	temp |= mask;
+	temp &= ~mask;
+	__raw_writel(mask, value ? &g->set_data : &g->clr_data);
 	__raw_writel(temp, &g->dir);
 	spin_unlock(&gpio_lock);
 	return 0;
 }
-EXPORT_SYMBOL(gpio_direction_input);
 
-int gpio_direction_output(unsigned gpio, int value)
+/*
+ * Assuming the pin is muxed as a gpio output, set its output value.
+ */
+static void
+davinci_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	struct gpio_controller *__iomem g = gpio2controller(gpio);
-	u32 temp;
-	u32 mask;
+	struct davinci_gpio *d = container_of(chip, struct davinci_gpio, chip);
+	struct gpio_controller *__iomem g = d->regs;
 
-	if (!g)
-		return -EINVAL;
+	__raw_writel((1 << offset), value ? &g->set_data : &g->clr_data);
+}
+
+static int __init davinci_gpio_setup(void)
+{
+	int i, base;
+
+	for (i = 0, base = 0;
+			i < ARRAY_SIZE(chips);
+			i++, base += 32) {
+		chips[i].chip.label = "DaVinci";
+
+		chips[i].chip.direction_input = davinci_direction_in;
+		chips[i].chip.get = davinci_gpio_get;
+		chips[i].chip.direction_output = davinci_direction_out;
+		chips[i].chip.set = davinci_gpio_set;
+
+		chips[i].chip.base = base;
+		chips[i].chip.ngpio = DAVINCI_N_GPIO - base;
+		if (chips[i].chip.ngpio > 32)
+			chips[i].chip.ngpio = 32;
+
+		chips[i].regs = gpio2controller(base);
+
+		gpiochip_add(&chips[i].chip);
+	}
 
-	spin_lock(&gpio_lock);
-	mask = __gpio_mask(gpio);
-	temp = __raw_readl(&g->dir);
-	temp &= ~mask;
-	__raw_writel(mask, value ? &g->set_data : &g->clr_data);
-	__raw_writel(temp, &g->dir);
-	spin_unlock(&gpio_lock);
 	return 0;
 }
-EXPORT_SYMBOL(gpio_direction_output);
+pure_initcall(davinci_gpio_setup);
 
+/*--------------------------------------------------------------------------*/
 /*
  * We expect irqs will normally be set up as input pins, but they can also be
  * used as output pins ... which is convenient for testing.
diff --git a/arch/arm/mach-davinci/include/mach/common.h b/arch/arm/mach-davinci/include/mach/common.h
index a97dfbb15e5..4b522e5c70e 100644
--- a/arch/arm/mach-davinci/include/mach/common.h
+++ b/arch/arm/mach-davinci/include/mach/common.h
@@ -16,4 +16,7 @@ struct sys_timer;
 
 extern struct sys_timer davinci_timer;
 
+/* parameters describe VBUS sourcing for host mode */
+extern void setup_usb(unsigned mA, unsigned potpgt_msec);
+
 #endif /* __ARCH_ARM_MACH_DAVINCI_COMMON_H */
diff --git a/arch/arm/mach-davinci/include/mach/gpio.h b/arch/arm/mach-davinci/include/mach/gpio.h
index ec151ccf1e8..b3a2961f0f4 100644
--- a/arch/arm/mach-davinci/include/mach/gpio.h
+++ b/arch/arm/mach-davinci/include/mach/gpio.h
@@ -14,6 +14,7 @@
 #define	__DAVINCI_GPIO_H
 
 #include <linux/io.h>
+#include <asm-generic/gpio.h>
 #include <mach/hardware.h>
 
 /*
@@ -27,13 +28,16 @@
  * need to pay attention to PINMUX0 and PINMUX1 to be sure those pins are
  * used as gpios, not with other peripherals.
  *
- * GPIOs are numbered 0..(DAVINCI_N_GPIO-1).  For documentation, and maybe
- * for later updates, code should write GPIO(N) or:
+ * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1).  For documentation,
+ * and maybe for later updates, code should write GPIO(N) or:
  *  - GPIOV18(N) for 1.8V pins, N in 0..53; same as GPIO(0)..GPIO(53)
  *  - GPIOV33(N) for 3.3V pins, N in 0..17; same as GPIO(54)..GPIO(70)
  *
  * For GPIO IRQs use gpio_to_irq(GPIO(N)) or gpio_to_irq(GPIOV33(N)) etc
  * for now, that's != GPIO(N)
+ *
+ * GPIOs can also be on external chips, numbered after the ones built-in
+ * to the DaVinci chip.  For now, they won't be usable as IRQ sources.
  */
 #define	GPIO(X)		(X)		/* 0 <= X <= 70 */
 #define	GPIOV18(X)	(X)		/* 1.8V i/o; 0 <= X <= 53 */
@@ -67,11 +71,11 @@ __gpio_to_controller(unsigned gpio)
 	void *__iomem ptr;
 
 	if (gpio < 32)
-		ptr = (void *__iomem)IO_ADDRESS(DAVINCI_GPIO_BASE + 0x10);
+		ptr = IO_ADDRESS(DAVINCI_GPIO_BASE + 0x10);
 	else if (gpio < 64)
-		ptr = (void *__iomem)IO_ADDRESS(DAVINCI_GPIO_BASE + 0x38);
+		ptr = IO_ADDRESS(DAVINCI_GPIO_BASE + 0x38);
 	else if (gpio < DAVINCI_N_GPIO)
-		ptr = (void *__iomem)IO_ADDRESS(DAVINCI_GPIO_BASE + 0x60);
+		ptr = IO_ADDRESS(DAVINCI_GPIO_BASE + 0x60);
 	else
 		ptr = NULL;
 	return ptr;
@@ -83,25 +87,17 @@ static inline u32 __gpio_mask(unsigned gpio)
 }
 
 /* The get/set/clear functions will inline when called with constant
- * parameters, for low-overhead bitbanging.  Illegal constant parameters
- * cause link-time errors.
+ * parameters referencing built-in GPIOs, for low-overhead bitbanging.
  *
- * Otherwise, calls with variable parameters use outlined functions.
+ * Otherwise, calls with variable parameters or referencing external
+ * GPIOs (e.g. on GPIO expander chips) use outlined functions.
  */
-extern int __error_inval_gpio(void);
-
-extern void __gpio_set(unsigned gpio, int value);
-extern int __gpio_get(unsigned gpio);
-
 static inline void gpio_set_value(unsigned gpio, int value)
 {
-	if (__builtin_constant_p(value)) {
+	if (__builtin_constant_p(value) && gpio < DAVINCI_N_GPIO) {
 		struct gpio_controller	*__iomem g;
 		u32			mask;
 
-		if (gpio >= DAVINCI_N_GPIO)
-			__error_inval_gpio();
-
 		g = __gpio_to_controller(gpio);
 		mask = __gpio_mask(gpio);
 		if (value)
@@ -111,48 +107,47 @@ static inline void gpio_set_value(unsigned gpio, int value)
 		return;
 	}
 
-	__gpio_set(gpio, value);
+	__gpio_set_value(gpio, value);
 }
 
 /* Returns zero or nonzero; works for gpios configured as inputs OR
- * as outputs.
+ * as outputs, at least for built-in GPIOs.
  *
- * NOTE: changes in reported values are synchronized to the GPIO clock.
- * This is most easily seen after calling gpio_set_value() and then immediatly
- * gpio_get_value(), where the gpio_get_value() would return the old value
- * until the GPIO clock ticks and the new value gets latched.
+ * NOTE: for built-in GPIOs, changes in reported values are synchronized
+ * to the GPIO clock.  This is easily seen after calling gpio_set_value()
+ * and then immediately gpio_get_value(), where the gpio_get_value() will
+ * return the old value until the GPIO clock ticks and the new value gets
+ * latched.
  */
-
 static inline int gpio_get_value(unsigned gpio)
 {
-	struct gpio_controller *__iomem g;
-
-	if (!__builtin_constant_p(gpio))
-		return __gpio_get(gpio);
+	struct gpio_controller	*__iomem g;
 
-	if (gpio >= DAVINCI_N_GPIO)
-		return __error_inval_gpio();
+	if (!__builtin_constant_p(gpio) || gpio >= DAVINCI_N_GPIO)
+		return __gpio_get_value(gpio);
 
 	g = __gpio_to_controller(gpio);
-	return !!(__gpio_mask(gpio) & __raw_readl(&g->in_data));
+	return __gpio_mask(gpio) & __raw_readl(&g->in_data);
 }
 
-/* powerup default direction is IN */
-extern int gpio_direction_input(unsigned gpio);
-extern int gpio_direction_output(unsigned gpio, int value);
-
-#include <asm-generic/gpio.h>	/* cansleep wrappers */
-
-extern int gpio_request(unsigned gpio, const char *tag);
-extern void gpio_free(unsigned gpio);
+static inline int gpio_cansleep(unsigned gpio)
+{
+	if (__builtin_constant_p(gpio) && gpio < DAVINCI_N_GPIO)
+		return 0;
+	else
+		return __gpio_cansleep(gpio);
+}
 
 static inline int gpio_to_irq(unsigned gpio)
 {
+	if (gpio >= DAVINCI_N_GPIO)
+		return -EINVAL;
 	return DAVINCI_N_AINTC_IRQ + gpio;
 }
 
 static inline int irq_to_gpio(unsigned irq)
 {
+	/* caller guarantees gpio_to_irq() succeeded */
 	return irq - DAVINCI_N_AINTC_IRQ;
 }
 
diff --git a/arch/arm/mach-davinci/include/mach/i2c.h b/arch/arm/mach-davinci/include/mach/i2c.h
index e2f54168abd..c248e9b7e82 100644
--- a/arch/arm/mach-davinci/include/mach/i2c.h
+++ b/arch/arm/mach-davinci/include/mach/i2c.h
@@ -14,8 +14,11 @@
 
 /* All frequencies are expressed in kHz */
 struct davinci_i2c_platform_data {
-	unsigned int	bus_freq;	/* standard bus frequency */
-	unsigned int	bus_delay;	/* transaction delay */
+	unsigned int	bus_freq;	/* standard bus frequency (kHz) */
+	unsigned int	bus_delay;	/* post-transaction delay (usec) */
 };
 
+/* for board setup code */
+void davinci_init_i2c(struct davinci_i2c_platform_data *);
+
 #endif /* __ASM_ARCH_I2C_H */
diff --git a/arch/arm/mach-davinci/include/mach/io.h b/arch/arm/mach-davinci/include/mach/io.h
index e7accb91086..b78ee914049 100644
--- a/arch/arm/mach-davinci/include/mach/io.h
+++ b/arch/arm/mach-davinci/include/mach/io.h
@@ -22,9 +22,8 @@
 #define IO_OFFSET	0xfd000000 /* Virtual IO = 0xfec00000 */
 #define IO_SIZE		0x00400000
 #define IO_VIRT		(IO_PHYS + IO_OFFSET)
-#define io_p2v(pa)	((pa) + IO_OFFSET)
 #define io_v2p(va)	((va) - IO_OFFSET)
-#define IO_ADDRESS(x)	io_p2v(x)
+#define __IO_ADDRESS(x)	((x) + IO_OFFSET)
 
 /*
  * We don't actually have real ISA nor PCI buses, but there is so many
@@ -35,7 +34,12 @@
 #define __mem_pci(a)		(a)
 #define __mem_isa(a)		(a)
 
-#ifndef __ASSEMBLER__
+#define IO_ADDRESS(pa)          IOMEM(__IO_ADDRESS(pa))
+
+#ifdef __ASSEMBLER__
+#define IOMEM(x)                x
+#else
+#define IOMEM(x)                ((void __force __iomem *)(x))
 
 /*
  * Functions to access the DaVinci IO region
@@ -46,34 +50,13 @@
  *	 - DO NOT use hardcoded virtual addresses to allow changing the
  *	   IO address space again if needed
  */
-#define davinci_readb(a)	(*(volatile unsigned char  *)IO_ADDRESS(a))
-#define davinci_readw(a)	(*(volatile unsigned short *)IO_ADDRESS(a))
-#define davinci_readl(a)	(*(volatile unsigned int   *)IO_ADDRESS(a))
-
-#define davinci_writeb(v,a)	(*(volatile unsigned char  *)IO_ADDRESS(a) = (v))
-#define davinci_writew(v,a)	(*(volatile unsigned short *)IO_ADDRESS(a) = (v))
-#define davinci_writel(v,a)	(*(volatile unsigned int   *)IO_ADDRESS(a) = (v))
-
-/* 16 bit uses LDRH/STRH, base +/- offset_8 */
-typedef struct { volatile u16 offset[256]; } __regbase16;
-#define __REGV16(vaddr)		((__regbase16 *)((vaddr)&~0xff)) \
-					->offset[((vaddr)&0xff)>>1]
-#define __REG16(paddr)          __REGV16(io_p2v(paddr))
-
-/* 8/32 bit uses LDR/STR, base +/- offset_12 */
-typedef struct { volatile u8 offset[4096]; } __regbase8;
-#define __REGV8(vaddr)		((__regbase8  *)((vaddr)&~4095)) \
-					->offset[((vaddr)&4095)>>0]
-#define __REG8(paddr)		__REGV8(io_p2v(paddr))
-
-typedef struct { volatile u32 offset[4096]; } __regbase32;
-#define __REGV32(vaddr)		((__regbase32 *)((vaddr)&~4095)) \
-					->offset[((vaddr)&4095)>>2]
-
-#define __REG(paddr)		__REGV32(io_p2v(paddr))
-#else
+#define davinci_readb(a)	__raw_readb(IO_ADDRESS(a))
+#define davinci_readw(a)	__raw_readw(IO_ADDRESS(a))
+#define davinci_readl(a)	__raw_readl(IO_ADDRESS(a))
 
-#define __REG(x)	(*((volatile unsigned long *)io_p2v(x)))
+#define davinci_writeb(v, a)	__raw_writeb(v, IO_ADDRESS(a))
+#define davinci_writew(v, a)	__raw_writew(v, IO_ADDRESS(a))
+#define davinci_writel(v, a)	__raw_writel(v, IO_ADDRESS(a))
 
 #endif /* __ASSEMBLER__ */
 #endif /* __ASM_ARCH_IO_H */
diff --git a/arch/arm/mach-davinci/usb.c b/arch/arm/mach-davinci/usb.c
new file mode 100644
index 00000000000..fe182a85159
--- /dev/null
+++ b/arch/arm/mach-davinci/usb.c
@@ -0,0 +1,116 @@
+/*
+ * USB
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+
+#include <linux/usb/musb.h>
+#include <linux/usb/otg.h>
+
+#include <mach/common.h>
+#include <mach/hardware.h>
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct musb_hdrc_eps_bits musb_eps[] = {
+	{ "ep1_tx", 8, },
+	{ "ep1_rx", 8, },
+	{ "ep2_tx", 8, },
+	{ "ep2_rx", 8, },
+	{ "ep3_tx", 5, },
+	{ "ep3_rx", 5, },
+	{ "ep4_tx", 5, },
+	{ "ep4_rx", 5, },
+};
+
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= true,
+	.dyn_fifo	= true,
+	.soft_con	= true,
+	.dma		= true,
+
+	.num_eps	= 5,
+	.dma_channels	= 8,
+	.ram_bits	= 10,
+	.eps_bits	= musb_eps,
+};
+
+static struct musb_hdrc_platform_data usb_data = {
+#if defined(CONFIG_USB_MUSB_OTG)
+	/* OTG requires a Mini-AB connector */
+	.mode           = MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
+	.mode           = MUSB_PERIPHERAL,
+#elif defined(CONFIG_USB_MUSB_HOST)
+	.mode           = MUSB_HOST,
+#endif
+	.config		= &musb_config,
+};
+
+static struct resource usb_resources[] = {
+	{
+		/* physical address */
+		.start          = DAVINCI_USB_OTG_BASE,
+		.end            = DAVINCI_USB_OTG_BASE + 0x5ff,
+		.flags          = IORESOURCE_MEM,
+	},
+	{
+		.start          = IRQ_USBINT,
+		.flags          = IORESOURCE_IRQ,
+	},
+};
+
+static u64 usb_dmamask = DMA_32BIT_MASK;
+
+static struct platform_device usb_dev = {
+	.name           = "musb_hdrc",
+	.id             = -1,
+	.dev = {
+		.platform_data		= &usb_data,
+		.dma_mask		= &usb_dmamask,
+		.coherent_dma_mask      = DMA_32BIT_MASK,
+	},
+	.resource       = usb_resources,
+	.num_resources  = ARRAY_SIZE(usb_resources),
+};
+
+#ifdef CONFIG_USB_MUSB_OTG
+
+static struct otg_transceiver *xceiv;
+
+struct otg_transceiver *otg_get_transceiver(void)
+{
+	if (xceiv)
+		get_device(xceiv->dev);
+	return xceiv;
+}
+EXPORT_SYMBOL(otg_get_transceiver);
+
+int otg_set_transceiver(struct otg_transceiver *x)
+{
+	if (xceiv && x)
+		return -EBUSY;
+	xceiv = x;
+	return 0;
+}
+EXPORT_SYMBOL(otg_set_transceiver);
+
+#endif
+
+void __init setup_usb(unsigned mA, unsigned potpgt_msec)
+{
+	usb_data.power = mA / 2;
+	usb_data.potpgt = potpgt_msec / 2;
+	platform_device_register(&usb_dev);
+}
+
+#else
+
+void __init setup_usb(unsigned mA, unsigned potpgt_msec)
+{
+}
+
+#endif  /* CONFIG_USB_MUSB_HDRC */
+