Merge git://git.marvell.com/orion into devel

7 files changed, 272 insertions, 2 deletions

diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 532443622a1..b5421cccd7e 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -26,6 +26,12 @@ config MACH_SHEEVAPLUG
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell SheevaPlug Reference Board.
 
+config MACH_TS219
+	bool "QNAP TS-119 and TS-219 Turbo NAS"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  QNAP TS-119 and TS-219 Turbo NAS devices.
+
 endmenu
 
 endif
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index de81b4b5bd3..8f03c9b9bdd 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_MACH_DB88F6281_BP)		+= db88f6281-bp-setup.o
 obj-$(CONFIG_MACH_RD88F6192_NAS)	+= rd88f6192-nas-setup.o
 obj-$(CONFIG_MACH_RD88F6281)		+= rd88f6281-setup.o
 obj-$(CONFIG_MACH_SHEEVAPLUG)		+= sheevaplug-setup.o
+obj-$(CONFIG_MACH_TS219)		+= ts219-setup.o
diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c
index 9f012551794..19b03f62c3f 100644
--- a/arch/arm/mach-kirkwood/common.c
+++ b/arch/arm/mach-kirkwood/common.c
@@ -14,6 +14,7 @@
 #include <linux/serial_8250.h>
 #include <linux/mbus.h>
 #include <linux/mv643xx_eth.h>
+#include <linux/mv643xx_i2c.h>
 #include <linux/ata_platform.h>
 #include <linux/spi/orion_spi.h>
 #include <net/dsa.h>
@@ -371,6 +372,45 @@ void __init kirkwood_spi_init()
 
 
 /*****************************************************************************
+ * I2C
+ ****************************************************************************/
+static struct mv64xxx_i2c_pdata kirkwood_i2c_pdata = {
+	.freq_m		= 8, /* assumes 166 MHz TCLK */
+	.freq_n		= 3,
+	.timeout	= 1000, /* Default timeout of 1 second */
+};
+
+static struct resource kirkwood_i2c_resources[] = {
+	{
+		.name	= "i2c",
+		.start	= I2C_PHYS_BASE,
+		.end	= I2C_PHYS_BASE + 0x1f,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.name	= "i2c",
+		.start	= IRQ_KIRKWOOD_TWSI,
+		.end	= IRQ_KIRKWOOD_TWSI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device kirkwood_i2c = {
+	.name		= MV64XXX_I2C_CTLR_NAME,
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(kirkwood_i2c_resources),
+	.resource	= kirkwood_i2c_resources,
+	.dev		= {
+		.platform_data	= &kirkwood_i2c_pdata,
+	},
+};
+
+void __init kirkwood_i2c_init(void)
+{
+	platform_device_register(&kirkwood_i2c);
+}
+
+
+/*****************************************************************************
  * UART0
  ****************************************************************************/
 static struct plat_serial8250_port kirkwood_uart0_data[] = {
diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
index 9e5282684d5..6ee88406f38 100644
--- a/arch/arm/mach-kirkwood/common.h
+++ b/arch/arm/mach-kirkwood/common.h
@@ -37,9 +37,11 @@ void kirkwood_pcie_init(void);
 void kirkwood_sata_init(struct mv_sata_platform_data *sata_data);
 void kirkwood_sdio_init(struct mvsdio_platform_data *mvsdio_data);
 void kirkwood_spi_init(void);
+void kirkwood_i2c_init(void);
 void kirkwood_uart0_init(void);
 void kirkwood_uart1_init(void);
 
+extern int kirkwood_tclk;
 extern struct sys_timer kirkwood_timer;
 
 
diff --git a/arch/arm/mach-kirkwood/include/mach/kirkwood.h b/arch/arm/mach-kirkwood/include/mach/kirkwood.h
index d3db30fe763..38c98685359 100644
--- a/arch/arm/mach-kirkwood/include/mach/kirkwood.h
+++ b/arch/arm/mach-kirkwood/include/mach/kirkwood.h
@@ -93,6 +93,7 @@
 #define  DEVICE_ID		(DEV_BUS_VIRT_BASE | 0x0034)
 #define  RTC_PHYS_BASE		(DEV_BUS_PHYS_BASE | 0x0300)
 #define  SPI_PHYS_BASE		(DEV_BUS_PHYS_BASE | 0x0600)
+#define  I2C_PHYS_BASE		(DEV_BUS_PHYS_BASE | 0x1000)
 #define  UART0_PHYS_BASE	(DEV_BUS_PHYS_BASE | 0x2000)
 #define  UART0_VIRT_BASE	(DEV_BUS_VIRT_BASE | 0x2000)
 #define  UART1_PHYS_BASE	(DEV_BUS_PHYS_BASE | 0x2100)
diff --git a/arch/arm/mach-kirkwood/mpp.h b/arch/arm/mach-kirkwood/mpp.h
index 45cccb74310..e021a80c2ca 100644
--- a/arch/arm/mach-kirkwood/mpp.h
+++ b/arch/arm/mach-kirkwood/mpp.h
@@ -90,13 +90,13 @@
 
 #define MPP10_GPO		MPP( 10, 0x0, 0, 1, 1,   1,   1,   1    )
 #define MPP10_SPI_SCK		MPP( 10, 0x2, 0, 1, 1,   1,   1,   1    )
-#define MPP10_UArt0_TXD		MPP( 10, 0X3, 0, 1, 1,   1,   1,   1    )
+#define MPP10_UART0_TXD		MPP( 10, 0X3, 0, 1, 1,   1,   1,   1    )
 #define MPP10_SATA1_ACTn	MPP( 10, 0x5, 0, 1, 0,   0,   1,   1    )
 #define MPP10_PTP_TRIG_GEN	MPP( 10, 0xc, 0, 1, 1,   1,   1,   1    )
 
 #define MPP11_GPIO		MPP( 11, 0x0, 1, 1, 1,   1,   1,   1    )
 #define MPP11_SPI_MISO		MPP( 11, 0x2, 1, 0, 1,   1,   1,   1    )
-#define MPP11_UArt0_RXD		MPP( 11, 0x3, 1, 0, 1,   1,   1,   1    )
+#define MPP11_UART0_RXD		MPP( 11, 0x3, 1, 0, 1,   1,   1,   1    )
 #define MPP11_PTP_EVENT_REQ	MPP( 11, 0x4, 1, 0, 1,   1,   1,   1    )
 #define MPP11_PTP_TRIG_GEN	MPP( 11, 0xc, 0, 1, 1,   1,   1,   1    )
 #define MPP11_PTP_CLK		MPP( 11, 0xd, 1, 0, 1,   1,   1,   1    )
diff --git a/arch/arm/mach-kirkwood/ts219-setup.c b/arch/arm/mach-kirkwood/ts219-setup.c
new file mode 100644
index 00000000000..dda5743cf3e
--- /dev/null
+++ b/arch/arm/mach-kirkwood/ts219-setup.c
@@ -0,0 +1,220 @@
+/*
+ *
+ * QNAP TS-119/TS-219 Turbo NAS Board Setup
+ *
+ * Copyright (C) 2009  Martin Michlmayr <tbm@cyrius.com>
+ * Copyright (C) 2008  Byron Bradley <byron.bbradley@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/orion_spi.h>
+#include <linux/i2c.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/ata_platform.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/timex.h>
+#include <linux/serial_reg.h>
+#include <linux/pci.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+#include "mpp.h"
+
+/****************************************************************************
+ * 16 MiB NOR flash. The struct mtd_partition is not in the same order as the
+ *     partitions on the device because we want to keep compatability with
+ *     the QNAP firmware.
+ * Layout as used by QNAP:
+ *  0x00000000-0x00080000 : "U-Boot"
+ *  0x00200000-0x00400000 : "Kernel"
+ *  0x00400000-0x00d00000 : "RootFS"
+ *  0x00d00000-0x01000000 : "RootFS2"
+ *  0x00080000-0x000c0000 : "U-Boot Config"
+ *  0x000c0000-0x00200000 : "NAS Config"
+ *
+ * We'll use "RootFS1" instead of "RootFS" to stay compatible with the layout
+ * used by the QNAP TS-109/TS-209.
+ *
+ ***************************************************************************/
+
+static struct mtd_partition qnap_ts219_partitions[] = {
+	{
+		.name		= "U-Boot",
+		.size		= 0x00080000,
+		.offset		= 0,
+		.mask_flags	= MTD_WRITEABLE,
+	}, {
+		.name		= "Kernel",
+		.size		= 0x00200000,
+		.offset		= 0x00200000,
+	}, {
+		.name		= "RootFS1",
+		.size		= 0x00900000,
+		.offset		= 0x00400000,
+	}, {
+		.name		= "RootFS2",
+		.size		= 0x00300000,
+		.offset		= 0x00d00000,
+	}, {
+		.name		= "U-Boot Config",
+		.size		= 0x00040000,
+		.offset		= 0x00080000,
+	}, {
+		.name		= "NAS Config",
+		.size		= 0x00140000,
+		.offset		= 0x000c0000,
+	},
+};
+
+static const struct flash_platform_data qnap_ts219_flash = {
+	.type		= "m25p128",
+	.name		= "spi_flash",
+	.parts		= qnap_ts219_partitions,
+	.nr_parts	= ARRAY_SIZE(qnap_ts219_partitions),
+};
+
+static struct spi_board_info __initdata qnap_ts219_spi_slave_info[] = {
+	{
+		.modalias	= "m25p80",
+		.platform_data	= &qnap_ts219_flash,
+		.irq		= -1,
+		.max_speed_hz	= 20000000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+	},
+};
+
+static struct i2c_board_info __initdata qnap_ts219_i2c_rtc = {
+	I2C_BOARD_INFO("s35390a", 0x30),
+};
+
+static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
+};
+
+static struct mv_sata_platform_data qnap_ts219_sata_data = {
+	.n_ports	= 2,
+};
+
+static struct gpio_keys_button qnap_ts219_buttons[] = {
+	{
+		.code		= KEY_COPY,
+		.gpio		= 15,
+		.desc		= "USB Copy",
+		.active_low	= 1,
+	},
+	{
+		.code		= KEY_RESTART,
+		.gpio		= 16,
+		.desc		= "Reset",
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_platform_data qnap_ts219_button_data = {
+	.buttons	= qnap_ts219_buttons,
+	.nbuttons	= ARRAY_SIZE(qnap_ts219_buttons),
+};
+
+static struct platform_device qnap_ts219_button_device = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.num_resources	= 0,
+	.dev		= {
+		.platform_data	= &qnap_ts219_button_data,
+	}
+};
+
+static unsigned int qnap_ts219_mpp_config[] __initdata = {
+	MPP0_SPI_SCn,
+	MPP1_SPI_MOSI,
+	MPP2_SPI_SCK,
+	MPP3_SPI_MISO,
+	MPP8_TW_SDA,
+	MPP9_TW_SCK,
+	MPP10_UART0_TXD,
+	MPP11_UART0_RXD,
+	MPP13_UART1_TXD,	/* PIC controller */
+	MPP14_UART1_RXD,	/* PIC controller */
+	MPP15_GPIO,		/* USB Copy button */
+	MPP16_GPIO,		/* Reset button */
+	MPP20_SATA1_ACTn,
+	MPP21_SATA0_ACTn,
+	MPP22_SATA1_PRESENTn,
+	MPP23_SATA0_PRESENTn,
+	0
+};
+
+
+/*****************************************************************************
+ * QNAP TS-x19 specific power off method via UART1-attached PIC
+ ****************************************************************************/
+
+#define UART1_REG(x)	(UART1_VIRT_BASE + ((UART_##x) << 2))
+
+void qnap_ts219_power_off(void)
+{
+	/* 19200 baud divisor */
+	const unsigned divisor = ((kirkwood_tclk + (8 * 19200)) / (16 * 19200));
+
+	pr_info("%s: triggering power-off...\n", __func__);
+
+	/* hijack UART1 and reset into sane state (19200,8n1) */
+	writel(0x83, UART1_REG(LCR));
+	writel(divisor & 0xff, UART1_REG(DLL));
+	writel((divisor >> 8) & 0xff, UART1_REG(DLM));
+	writel(0x03, UART1_REG(LCR));
+	writel(0x00, UART1_REG(IER));
+	writel(0x00, UART1_REG(FCR));
+	writel(0x00, UART1_REG(MCR));
+
+	/* send the power-off command 'A' to PIC */
+	writel('A', UART1_REG(TX));
+}
+
+static void __init qnap_ts219_init(void)
+{
+	/*
+	 * Basic setup. Needs to be called early.
+	 */
+	kirkwood_init();
+	kirkwood_mpp_conf(qnap_ts219_mpp_config);
+
+	kirkwood_uart0_init();
+	kirkwood_uart1_init(); /* A PIC controller is connected here. */
+	spi_register_board_info(qnap_ts219_spi_slave_info,
+				ARRAY_SIZE(qnap_ts219_spi_slave_info));
+	kirkwood_spi_init();
+	kirkwood_i2c_init();
+	i2c_register_board_info(0, &qnap_ts219_i2c_rtc, 1);
+	kirkwood_ge00_init(&qnap_ts219_ge00_data);
+	kirkwood_sata_init(&qnap_ts219_sata_data);
+	kirkwood_ehci_init();
+	platform_device_register(&qnap_ts219_button_device);
+
+	pm_power_off = qnap_ts219_power_off;
+
+}
+
+MACHINE_START(TS219, "QNAP TS-119/TS-219")
+	/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
+	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
+	.io_pg_offst	= ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x00000100,
+	.init_machine	= qnap_ts219_init,
+	.map_io		= kirkwood_map_io,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &kirkwood_timer,
+MACHINE_END