ARM i.MX: Merge i.MX5 support into mach-imx

This patch moves the contents of arch/arm/mach-mx5 to arch/arm/mach-imx
and adjusts the Makefile/Kconfig entries in a way that it's possible
to compile i.MX5 together with i.MX3/6.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>

1 files changed, 0 insertions, 338 deletions

diff --git a/arch/arm/mach-mx5/board-cpuimx51sd.c b/arch/arm/mach-mx5/board-cpuimx51sd.c
deleted file mode 100644
index 52a11c1898e..00000000000
--- a/arch/arm/mach-mx5/board-cpuimx51sd.c
+++ /dev/null
@@ -1,338 +0,0 @@
-/*
- *
- * Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
- *
- * based on board-mx51_babbage.c which is
- * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/i2c.h>
-#include <linux/i2c/tsc2007.h>
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/interrupt.h>
-#include <linux/i2c-gpio.h>
-#include <linux/spi/spi.h>
-#include <linux/can/platform/mcp251x.h>
-
-#include <mach/eukrea-baseboards.h>
-#include <mach/common.h>
-#include <mach/hardware.h>
-#include <mach/iomux-mx51.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "devices-imx51.h"
-#include "cpu_op-mx51.h"
-
-#define USBH1_RST		IMX_GPIO_NR(2, 28)
-#define ETH_RST			IMX_GPIO_NR(2, 31)
-#define TSC2007_IRQGPIO		IMX_GPIO_NR(3, 12)
-#define CAN_IRQGPIO		IMX_GPIO_NR(1, 1)
-#define CAN_RST			IMX_GPIO_NR(4, 15)
-#define CAN_NCS			IMX_GPIO_NR(4, 24)
-#define CAN_RXOBF		IMX_GPIO_NR(1, 4)
-#define CAN_RX1BF		IMX_GPIO_NR(1, 6)
-#define CAN_TXORTS		IMX_GPIO_NR(1, 7)
-#define CAN_TX1RTS		IMX_GPIO_NR(1, 8)
-#define CAN_TX2RTS		IMX_GPIO_NR(1, 9)
-#define I2C_SCL			IMX_GPIO_NR(4, 16)
-#define I2C_SDA			IMX_GPIO_NR(4, 17)
-
-/* USB_CTRL_1 */
-#define MX51_USB_CTRL_1_OFFSET		0x10
-#define MX51_USB_CTRL_UH1_EXT_CLK_EN	(1 << 25)
-
-#define	MX51_USB_PLLDIV_12_MHZ		0x00
-#define	MX51_USB_PLL_DIV_19_2_MHZ	0x01
-#define	MX51_USB_PLL_DIV_24_MHZ		0x02
-
-static iomux_v3_cfg_t eukrea_cpuimx51sd_pads[] = {
-	/* UART1 */
-	MX51_PAD_UART1_RXD__UART1_RXD,
-	MX51_PAD_UART1_TXD__UART1_TXD,
-	MX51_PAD_UART1_RTS__UART1_RTS,
-	MX51_PAD_UART1_CTS__UART1_CTS,
-
-	/* USB HOST1 */
-	MX51_PAD_USBH1_CLK__USBH1_CLK,
-	MX51_PAD_USBH1_DIR__USBH1_DIR,
-	MX51_PAD_USBH1_NXT__USBH1_NXT,
-	MX51_PAD_USBH1_DATA0__USBH1_DATA0,
-	MX51_PAD_USBH1_DATA1__USBH1_DATA1,
-	MX51_PAD_USBH1_DATA2__USBH1_DATA2,
-	MX51_PAD_USBH1_DATA3__USBH1_DATA3,
-	MX51_PAD_USBH1_DATA4__USBH1_DATA4,
-	MX51_PAD_USBH1_DATA5__USBH1_DATA5,
-	MX51_PAD_USBH1_DATA6__USBH1_DATA6,
-	MX51_PAD_USBH1_DATA7__USBH1_DATA7,
-	MX51_PAD_USBH1_STP__USBH1_STP,
-	MX51_PAD_EIM_CS3__GPIO2_28,		/* PHY nRESET */
-
-	/* FEC */
-	MX51_PAD_EIM_DTACK__GPIO2_31,		/* PHY nRESET */
-
-	/* HSI2C */
-	MX51_PAD_I2C1_CLK__GPIO4_16,
-	MX51_PAD_I2C1_DAT__GPIO4_17,
-
-	/* CAN */
-	MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
-	MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
-	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
-	MX51_PAD_CSPI1_SS0__GPIO4_24,		/* nCS */
-	MX51_PAD_CSI2_PIXCLK__GPIO4_15,		/* nReset */
-	MX51_PAD_GPIO1_1__GPIO1_1,		/* IRQ */
-	MX51_PAD_GPIO1_4__GPIO1_4,		/* Control signals */
-	MX51_PAD_GPIO1_6__GPIO1_6,
-	MX51_PAD_GPIO1_7__GPIO1_7,
-	MX51_PAD_GPIO1_8__GPIO1_8,
-	MX51_PAD_GPIO1_9__GPIO1_9,
-
-	/* Touchscreen */
-	/* IRQ */
-	NEW_PAD_CTRL(MX51_PAD_GPIO_NAND__GPIO_NAND, PAD_CTL_PUS_22K_UP |
-			PAD_CTL_PKE | PAD_CTL_SRE_FAST |
-			PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct tsc2007_platform_data tsc2007_info = {
-	.model			= 2007,
-	.x_plate_ohms		= 180,
-};
-
-static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	}, {
-		I2C_BOARD_INFO("tsc2007", 0x49),
-		.type		= "tsc2007",
-		.platform_data	= &tsc2007_info,
-		.irq		= IMX_GPIO_TO_IRQ(TSC2007_IRQGPIO),
-	},
-};
-
-static const struct mxc_nand_platform_data
-		eukrea_cpuimx51sd_nand_board_info __initconst = {
-	.width		= 1,
-	.hw_ecc		= 1,
-	.flash_bbt	= 1,
-};
-
-/* This function is board specific as the bit mask for the plldiv will also
-be different for other Freescale SoCs, thus a common bitmask is not
-possible and cannot get place in /plat-mxc/ehci.c.*/
-static int initialize_otg_port(struct platform_device *pdev)
-{
-	u32 v;
-	void __iomem *usb_base;
-	void __iomem *usbother_base;
-
-	usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
-	if (!usb_base)
-		return -ENOMEM;
-	usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
-
-	/* Set the PHY clock to 19.2MHz */
-	v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
-	v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
-	v |= MX51_USB_PLL_DIV_19_2_MHZ;
-	__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
-	iounmap(usb_base);
-
-	mdelay(10);
-
-	return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
-}
-
-static int initialize_usbh1_port(struct platform_device *pdev)
-{
-	u32 v;
-	void __iomem *usb_base;
-	void __iomem *usbother_base;
-
-	usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
-	if (!usb_base)
-		return -ENOMEM;
-	usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
-
-	/* The clock for the USBH1 ULPI port will come from the PHY. */
-	v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
-	__raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN,
-			usbother_base + MX51_USB_CTRL_1_OFFSET);
-	iounmap(usb_base);
-
-	mdelay(10);
-
-	return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
-			MXC_EHCI_ITC_NO_THRESHOLD);
-}
-
-static const struct mxc_usbh_platform_data dr_utmi_config __initconst = {
-	.init		= initialize_otg_port,
-	.portsc	= MXC_EHCI_UTMI_16BIT,
-};
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
-	.operating_mode	= FSL_USB2_DR_DEVICE,
-	.phy_mode	= FSL_USB2_PHY_UTMI_WIDE,
-};
-
-static const struct mxc_usbh_platform_data usbh1_config __initconst = {
-	.init		= initialize_usbh1_port,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static int otg_mode_host;
-
-static int __init eukrea_cpuimx51sd_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = 1;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = 0;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 0;
-}
-__setup("otg_mode=", eukrea_cpuimx51sd_otg_mode);
-
-static struct i2c_gpio_platform_data pdata = {
-	.sda_pin		= I2C_SDA,
-	.sda_is_open_drain	= 0,
-	.scl_pin		= I2C_SCL,
-	.scl_is_open_drain	= 0,
-	.udelay			= 2,
-};
-
-static struct platform_device hsi2c_gpio_device = {
-	.name			= "i2c-gpio",
-	.id			= 0,
-	.dev.platform_data	= &pdata,
-};
-
-static struct mcp251x_platform_data mcp251x_info = {
-	.oscillator_frequency = 24E6,
-};
-
-static struct spi_board_info cpuimx51sd_spi_device[] = {
-	{
-		.modalias        = "mcp2515",
-		.max_speed_hz    = 10000000,
-		.bus_num         = 0,
-		.mode		= SPI_MODE_0,
-		.chip_select     = 0,
-		.platform_data   = &mcp251x_info,
-		.irq             = IMX_GPIO_TO_IRQ(CAN_IRQGPIO)
-	},
-};
-
-static int cpuimx51sd_spi1_cs[] = {
-	CAN_NCS,
-};
-
-static const struct spi_imx_master cpuimx51sd_ecspi1_pdata __initconst = {
-	.chipselect	= cpuimx51sd_spi1_cs,
-	.num_chipselect	= ARRAY_SIZE(cpuimx51sd_spi1_cs),
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&hsi2c_gpio_device,
-};
-
-static void __init eukrea_cpuimx51sd_init(void)
-{
-	imx51_soc_init();
-
-	mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
-					ARRAY_SIZE(eukrea_cpuimx51sd_pads));
-
-#if defined(CONFIG_CPU_FREQ_IMX)
-	get_cpu_op = mx51_get_cpu_op;
-#endif
-
-	imx51_add_imx_uart(0, &uart_pdata);
-	imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);
-
-	gpio_request(ETH_RST, "eth_rst");
-	gpio_set_value(ETH_RST, 1);
-	imx51_add_fec(NULL);
-
-	gpio_request(CAN_IRQGPIO, "can_irq");
-	gpio_direction_input(CAN_IRQGPIO);
-	gpio_free(CAN_IRQGPIO);
-	gpio_request(CAN_NCS, "can_ncs");
-	gpio_direction_output(CAN_NCS, 1);
-	gpio_free(CAN_NCS);
-	gpio_request(CAN_RST, "can_rst");
-	gpio_direction_output(CAN_RST, 0);
-	msleep(20);
-	gpio_set_value(CAN_RST, 1);
-	imx51_add_ecspi(0, &cpuimx51sd_ecspi1_pdata);
-	spi_register_board_info(cpuimx51sd_spi_device,
-				ARRAY_SIZE(cpuimx51sd_spi_device));
-
-	gpio_request(TSC2007_IRQGPIO, "tsc2007_irq");
-	gpio_direction_input(TSC2007_IRQGPIO);
-	gpio_free(TSC2007_IRQGPIO);
-
-	i2c_register_board_info(0, eukrea_cpuimx51sd_i2c_devices,
-			ARRAY_SIZE(eukrea_cpuimx51sd_i2c_devices));
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-
-	if (otg_mode_host)
-		imx51_add_mxc_ehci_otg(&dr_utmi_config);
-	else {
-		initialize_otg_port(NULL);
-		imx51_add_fsl_usb2_udc(&usb_pdata);
-	}
-
-	gpio_request(USBH1_RST, "usb_rst");
-	gpio_direction_output(USBH1_RST, 0);
-	msleep(20);
-	gpio_set_value(USBH1_RST, 1);
-	imx51_add_mxc_ehci_hs(1, &usbh1_config);
-
-#ifdef CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD
-	eukrea_mbimxsd51_baseboard_init();
-#endif
-}
-
-static void __init eukrea_cpuimx51sd_timer_init(void)
-{
-	mx51_clocks_init(32768, 24000000, 22579200, 0);
-}
-
-static struct sys_timer mxc_timer = {
-	.init	= eukrea_cpuimx51sd_timer_init,
-};
-
-MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
-	/* Maintainer: Eric Bénard <eric@eukrea.com> */
-	.atag_offset = 0x100,
-	.map_io = mx51_map_io,
-	.init_early = imx51_init_early,
-	.init_irq = mx51_init_irq,
-	.handle_irq = imx51_handle_irq,
-	.timer = &mxc_timer,
-	.init_machine = eukrea_cpuimx51sd_init,
-MACHINE_END