OMAP4: PandaBoard: Adding DVI support

Adding DVI support to OMAP4 PandaBoard.

PandaBoard uses TFP410 DVI Framer chip
http://focus.ti.com/lit/ds/symlink/tfp410.pdf

The TFP410 gets its power enable and display data over GPIO lines muxed
in from OMAP4430. PandaBoard supports other LCD displays through
expansion
connectors, following board rework. This will disable the DVI interface.
However, the existing mux settings remain the same

PandaBoard additionally supports display over HDMI interface. It is
mutually exclusive to display over DVI. Hence the mux settings need to
be
configured seperately, as and when HDMI is enabled

Also, I2C3 bus used for reading EDID data from DVI Monitors is
registered here. Since the design is similar to BeagleBoard, the code
for the same is taken from the kernel.org commit e3333f48dd5cb21
(omap: Adding beagle i2c eeprom driver to read EDID)

Reviewed-by: Manjunath G Kondaiah <manjugk@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tomi.valkeinen@ti.com: fixed conflicts with HDMI]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

1 files changed, 129 insertions, 2 deletions

diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 795ffc46152..e2b912f376c 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -40,6 +40,7 @@
 #include <plat/common.h>
 #include <plat/usb.h>
 #include <plat/mmc.h>
+#include <plat/panel-generic-dpi.h>
 #include "timer-gp.h"
 
 #include "hsmmc.h"
@@ -435,6 +436,17 @@ static struct i2c_board_info __initdata omap4_panda_i2c_boardinfo[] = {
 		.platform_data = &omap4_panda_twldata,
 	},
 };
+
+/*
+ * Display monitor features are burnt in their EEPROM as EDID data. The EEPROM
+ * is connected as I2C slave device, and can be accessed at address 0x50
+ */
+static struct i2c_board_info __initdata panda_i2c_eeprom[] = {
+	{
+		I2C_BOARD_INFO("eeprom", 0x50),
+	},
+};
+
 static int __init omap4_panda_i2c_init(void)
 {
 	/*
@@ -444,7 +456,12 @@ static int __init omap4_panda_i2c_init(void)
 	omap_register_i2c_bus(1, 400, omap4_panda_i2c_boardinfo,
 			ARRAY_SIZE(omap4_panda_i2c_boardinfo));
 	omap_register_i2c_bus(2, 400, NULL, 0);
-	omap_register_i2c_bus(3, 400, NULL, 0);
+	/*
+	 * Bus 3 is attached to the DVI port where devices like the pico DLP
+	 * projector don't work reliably with 400kHz
+	 */
+	omap_register_i2c_bus(3, 100, panda_i2c_eeprom,
+					ARRAY_SIZE(panda_i2c_eeprom));
 	omap_register_i2c_bus(4, 400, NULL, 0);
 	return 0;
 }
@@ -464,12 +481,115 @@ static struct omap_board_mux board_mux[] __initdata = {
 	OMAP4_MUX(SDMMC5_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
 	OMAP4_MUX(SDMMC5_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
 	OMAP4_MUX(SDMMC5_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	/* gpio 0 - TFP410 PD */
+	OMAP4_MUX(KPD_COL1, OMAP_PIN_OUTPUT | OMAP_MUX_MODE3),
+	/* dispc2_data23 */
+	OMAP4_MUX(USBB2_ULPITLL_STP, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data22 */
+	OMAP4_MUX(USBB2_ULPITLL_DIR, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data21 */
+	OMAP4_MUX(USBB2_ULPITLL_NXT, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data20 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT0, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data19 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT1, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data18 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT2, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data15 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT3, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data14 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT4, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data13 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT5, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data12 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT6, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data11 */
+	OMAP4_MUX(USBB2_ULPITLL_DAT7, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data10 */
+	OMAP4_MUX(DPM_EMU3, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data9 */
+	OMAP4_MUX(DPM_EMU4, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data16 */
+	OMAP4_MUX(DPM_EMU5, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data17 */
+	OMAP4_MUX(DPM_EMU6, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_hsync */
+	OMAP4_MUX(DPM_EMU7, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_pclk */
+	OMAP4_MUX(DPM_EMU8, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_vsync */
+	OMAP4_MUX(DPM_EMU9, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_de */
+	OMAP4_MUX(DPM_EMU10, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data8 */
+	OMAP4_MUX(DPM_EMU11, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data7 */
+	OMAP4_MUX(DPM_EMU12, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data6 */
+	OMAP4_MUX(DPM_EMU13, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data5 */
+	OMAP4_MUX(DPM_EMU14, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data4 */
+	OMAP4_MUX(DPM_EMU15, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data3 */
+	OMAP4_MUX(DPM_EMU16, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data2 */
+	OMAP4_MUX(DPM_EMU17, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data1 */
+	OMAP4_MUX(DPM_EMU18, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* dispc2_data0 */
+	OMAP4_MUX(DPM_EMU19, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #else
 #define board_mux	NULL
 #endif
 
+/* Display DVI */
+#define PANDA_DVI_TFP410_POWER_DOWN_GPIO	0
+
+static int omap4_panda_enable_dvi(struct omap_dss_device *dssdev)
+{
+	gpio_set_value(dssdev->reset_gpio, 1);
+	return 0;
+}
+
+static void omap4_panda_disable_dvi(struct omap_dss_device *dssdev)
+{
+	gpio_set_value(dssdev->reset_gpio, 0);
+}
+
+/* Using generic display panel */
+static struct panel_generic_dpi_data omap4_dvi_panel = {
+	.name			= "generic",
+	.platform_enable	= omap4_panda_enable_dvi,
+	.platform_disable	= omap4_panda_disable_dvi,
+};
+
+struct omap_dss_device omap4_panda_dvi_device = {
+	.type			= OMAP_DISPLAY_TYPE_DPI,
+	.name			= "dvi",
+	.driver_name		= "generic_dpi_panel",
+	.data			= &omap4_dvi_panel,
+	.phy.dpi.data_lines	= 24,
+	.reset_gpio		= PANDA_DVI_TFP410_POWER_DOWN_GPIO,
+	.channel		= OMAP_DSS_CHANNEL_LCD2,
+};
+
+int __init omap4_panda_dvi_init(void)
+{
+	int r;
+
+	/* Requesting TFP410 DVI GPIO and disabling it, at bootup */
+	r = gpio_request_one(omap4_panda_dvi_device.reset_gpio,
+				GPIOF_OUT_INIT_LOW, "DVI PD");
+	if (r)
+		pr_err("Failed to get DVI powerdown GPIO\n");
+
+	return r;
+}
+
+
 static void omap4_panda_hdmi_mux_init(void)
 {
 	/* PAD0_HDMI_HPD_PAD1_HDMI_CEC */
@@ -525,17 +645,24 @@ static struct omap_dss_device  omap4_panda_hdmi_device = {
 };
 
 static struct omap_dss_device *omap4_panda_dss_devices[] = {
+	&omap4_panda_dvi_device,
 	&omap4_panda_hdmi_device,
 };
 
 static struct omap_dss_board_info omap4_panda_dss_data = {
 	.num_devices	= ARRAY_SIZE(omap4_panda_dss_devices),
 	.devices	= omap4_panda_dss_devices,
-	.default_device	= &omap4_panda_hdmi_device,
+	.default_device	= &omap4_panda_dvi_device,
 };
 
 void omap4_panda_display_init(void)
 {
+	int r;
+
+	r = omap4_panda_dvi_init();
+	if (r)
+		pr_err("error initializing panda DVI\n");
+
 	omap4_panda_hdmi_mux_init();
 	omap_display_init(&omap4_panda_dss_data);
 }