OMAP: adapt hsmmc to hwmod framework

OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.

Changes involves:
1) Remove controller reset in devices.c which is taken care of
   by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
   hwmod data file for base address, dma channel number, Irq_number,
   device attribute.
3) Update the driver to use dev_attr to find whether controller
   supports dual volt cards

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 0 insertions, 168 deletions

diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 2f4a598ba67..31632ac1ca7 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -544,112 +544,6 @@ static inline void omap_init_aes(void) { }
 
 /*-------------------------------------------------------------------------*/
 
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
-
-#define MMCHS_SYSCONFIG			0x0010
-#define MMCHS_SYSCONFIG_SWRESET		(1 << 1)
-#define MMCHS_SYSSTATUS			0x0014
-#define MMCHS_SYSSTATUS_RESETDONE	(1 << 0)
-
-static struct platform_device dummy_pdev = {
-	.dev = {
-		.bus = &platform_bus_type,
-	},
-};
-
-/**
- * omap_hsmmc_reset() - Full reset of each HS-MMC controller
- *
- * Ensure that each MMC controller is fully reset.  Controllers
- * left in an unknown state (by bootloader) may prevent retention
- * or OFF-mode.  This is especially important in cases where the
- * MMC driver is not enabled, _or_ built as a module.
- *
- * In order for reset to work, interface, functional and debounce
- * clocks must be enabled.  The debounce clock comes from func_32k_clk
- * and is not under SW control, so we only enable i- and f-clocks.
- **/
-static void __init omap_hsmmc_reset(void)
-{
-	u32 i, nr_controllers;
-	struct clk *iclk, *fclk;
-
-	if (cpu_is_omap242x())
-		return;
-
-	nr_controllers = cpu_is_omap44xx() ? OMAP44XX_NR_MMC :
-		(cpu_is_omap34xx() ? OMAP34XX_NR_MMC : OMAP24XX_NR_MMC);
-
-	for (i = 0; i < nr_controllers; i++) {
-		u32 v, base = 0;
-		struct device *dev = &dummy_pdev.dev;
-
-		switch (i) {
-		case 0:
-			base = OMAP2_MMC1_BASE;
-			break;
-		case 1:
-			base = OMAP2_MMC2_BASE;
-			break;
-		case 2:
-			base = OMAP3_MMC3_BASE;
-			break;
-		case 3:
-			if (!cpu_is_omap44xx())
-				return;
-			base = OMAP4_MMC4_BASE;
-			break;
-		case 4:
-			if (!cpu_is_omap44xx())
-				return;
-			base = OMAP4_MMC5_BASE;
-			break;
-		}
-
-		if (cpu_is_omap44xx())
-			base += OMAP4_MMC_REG_OFFSET;
-
-		dummy_pdev.id = i;
-		dev_set_name(&dummy_pdev.dev, "mmci-omap-hs.%d", i);
-		iclk = clk_get(dev, "ick");
-		if (IS_ERR(iclk))
-			goto err1;
-		if (clk_enable(iclk))
-			goto err2;
-
-		fclk = clk_get(dev, "fck");
-		if (IS_ERR(fclk))
-			goto err3;
-		if (clk_enable(fclk))
-			goto err4;
-
-		omap_writel(MMCHS_SYSCONFIG_SWRESET, base + MMCHS_SYSCONFIG);
-		v = omap_readl(base + MMCHS_SYSSTATUS);
-		while (!(omap_readl(base + MMCHS_SYSSTATUS) &
-			 MMCHS_SYSSTATUS_RESETDONE))
-			cpu_relax();
-
-		clk_disable(fclk);
-		clk_put(fclk);
-		clk_disable(iclk);
-		clk_put(iclk);
-	}
-	return;
-
-err4:
-	clk_put(fclk);
-err3:
-	clk_disable(iclk);
-err2:
-	clk_put(iclk);
-err1:
-	printk(KERN_WARNING "%s: Unable to enable clocks for MMC%d, "
-			    "cannot reset.\n",  __func__, i);
-}
-#else
-static inline void omap_hsmmc_reset(void) {}
-#endif
-
 #if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
 
 static inline void omap242x_mmc_mux(struct omap_mmc_platform_data
@@ -706,67 +600,6 @@ void __init omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
 
 #endif
 
-#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
-
-void __init omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,
-			int nr_controllers)
-{
-	int i;
-	char *name;
-
-	for (i = 0; i < nr_controllers; i++) {
-		unsigned long base, size;
-		unsigned int irq = 0;
-
-		if (!mmc_data[i])
-			continue;
-
-		switch (i) {
-		case 0:
-			base = OMAP2_MMC1_BASE;
-			irq = INT_24XX_MMC_IRQ;
-			break;
-		case 1:
-			base = OMAP2_MMC2_BASE;
-			irq = INT_24XX_MMC2_IRQ;
-			break;
-		case 2:
-			if (!cpu_is_omap44xx() && !cpu_is_omap34xx())
-				return;
-			base = OMAP3_MMC3_BASE;
-			irq = INT_34XX_MMC3_IRQ;
-			break;
-		case 3:
-			if (!cpu_is_omap44xx())
-				return;
-			base = OMAP4_MMC4_BASE;
-			irq = OMAP44XX_IRQ_MMC4;
-			break;
-		case 4:
-			if (!cpu_is_omap44xx())
-				return;
-			base = OMAP4_MMC5_BASE;
-			irq = OMAP44XX_IRQ_MMC5;
-			break;
-		default:
-			continue;
-		}
-
-		if (cpu_is_omap44xx()) {
-			if (i < 3)
-				irq += OMAP44XX_IRQ_GIC_START;
-			size = OMAP4_HSMMC_SIZE;
-			name = "mmci-omap-hs";
-		} else {
-			size = OMAP3_HSMMC_SIZE;
-			name = "mmci-omap-hs";
-		}
-		omap_mmc_add(name, i, base, size, irq, mmc_data[i]);
-	};
-}
-
-#endif
-
 /*-------------------------------------------------------------------------*/
 
 #if defined(CONFIG_HDQ_MASTER_OMAP) || defined(CONFIG_HDQ_MASTER_OMAP_MODULE)
@@ -836,7 +669,6 @@ static int __init omap2_init_devices(void)
 	 * please keep these calls, and their implementations above,
 	 * in alphabetical order so they're easier to sort through.
 	 */
-	omap_hsmmc_reset();
 	omap_init_audio();
 	omap_init_camera();
 	omap_init_mbox();