OMAP3 SDRC: add support for 2 SDRAM chip selects

Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.

This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS

Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers

Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).

Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

1 files changed, 107 insertions, 30 deletions

diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index f41f8d96ddb..3aef7448b2a 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -36,7 +36,7 @@
 
 	.text
 
-/* r4 parameters */
+/* r1 parameters */
 #define SDRC_NO_UNLOCK_DLL		0x0
 #define SDRC_UNLOCK_DLL			0x1
 
@@ -71,40 +71,71 @@
 
 /*
  * omap3_sram_configure_core_dpll - change DPLL3 M2 divider
- * r0 = new SDRC_RFR_CTRL register contents
- * r1 = new SDRC_ACTIM_CTRLA register contents
- * r2 = new SDRC_ACTIM_CTRLB register contents
- * r3 = new M2 divider setting (only 1 and 2 supported right now)
- * r4 = unlock SDRC DLL? (1 = yes, 0 = no).  Only unlock DLL for
+ *
+ * Params passed in registers:
+ *  r0 = new M2 divider setting (only 1 and 2 supported right now)
+ *  r1 = unlock SDRC DLL? (1 = yes, 0 = no).  Only unlock DLL for
  *      SDRC rates < 83MHz
- * r5 = number of MPU cycles to wait for SDRC to stabilize after
+ *  r2 = number of MPU cycles to wait for SDRC to stabilize after
  *      reprogramming the SDRC when switching to a slower MPU speed
- * r6 = new SDRC_MR_0 register value
- * r7 = increasing SDRC rate? (1 = yes, 0 = no)
+ *  r3 = increasing SDRC rate? (1 = yes, 0 = no)
+ *
+ * Params passed via the stack. The needed params will be copied in SRAM
+ *  before use by the code in SRAM (SDRAM is not accessible during SDRC
+ *  reconfiguration):
+ *  new SDRC_RFR_CTRL_0 register contents
+ *  new SDRC_ACTIM_CTRL_A_0 register contents
+ *  new SDRC_ACTIM_CTRL_B_0 register contents
+ *  new SDRC_MR_0 register value
+ *  new SDRC_RFR_CTRL_1 register contents
+ *  new SDRC_ACTIM_CTRL_A_1 register contents
+ *  new SDRC_ACTIM_CTRL_B_1 register contents
+ *  new SDRC_MR_1 register value
  *
+ * If the param SDRC_RFR_CTRL_1 is 0, the parameters
+ *  are not programmed into the SDRC CS1 registers
  */
 ENTRY(omap3_sram_configure_core_dpll)
 	stmfd	sp!, {r1-r12, lr}	@ store regs to stack
-	ldr	r4, [sp, #52]		@ pull extra args off the stack
-	ldr	r5, [sp, #56]		@ load extra args from the stack
-	ldr	r6, [sp, #60]		@ load extra args from the stack
-	ldr	r7, [sp, #64]		@ load extra args from the stack
+
+					@ pull the extra args off the stack
+					@  and store them in SRAM
+	ldr	r4, [sp, #52]
+	str     r4, omap_sdrc_rfr_ctrl_0_val
+	ldr	r4, [sp, #56]
+	str     r4, omap_sdrc_actim_ctrl_a_0_val
+	ldr	r4, [sp, #60]
+	str     r4, omap_sdrc_actim_ctrl_b_0_val
+	ldr	r4, [sp, #64]
+	str     r4, omap_sdrc_mr_0_val
+	ldr	r4, [sp, #68]
+	str     r4, omap_sdrc_rfr_ctrl_1_val
+	cmp	r4, #0			@ if SDRC_RFR_CTRL_1 is 0,
+	beq	skip_cs1_params		@  do not use cs1 params
+	ldr	r4, [sp, #72]
+	str     r4, omap_sdrc_actim_ctrl_a_1_val
+	ldr	r4, [sp, #76]
+	str     r4, omap_sdrc_actim_ctrl_b_1_val
+	ldr	r4, [sp, #80]
+	str     r4, omap_sdrc_mr_1_val
+skip_cs1_params:
 	dsb				@ flush buffered writes to interconnect
-	cmp	r7, #1			@ if increasing SDRC clk rate,
+
+	cmp	r3, #1			@ if increasing SDRC clk rate,
 	bleq	configure_sdrc		@ program the SDRC regs early (for RFR)
-	cmp	r4, #SDRC_UNLOCK_DLL	@ set the intended DLL state
+	cmp	r1, #SDRC_UNLOCK_DLL	@ set the intended DLL state
 	bleq	unlock_dll
 	blne	lock_dll
 	bl	sdram_in_selfrefresh	@ put SDRAM in self refresh, idle SDRC
 	bl 	configure_core_dpll	@ change the DPLL3 M2 divider
 	bl	enable_sdrc		@ take SDRC out of idle
-	cmp	r4, #SDRC_UNLOCK_DLL	@ wait for DLL status to change
+	cmp	r1, #SDRC_UNLOCK_DLL	@ wait for DLL status to change
 	bleq	wait_dll_unlock
 	blne	wait_dll_lock
-	cmp	r7, #1			@ if increasing SDRC clk rate,
+	cmp	r3, #1			@ if increasing SDRC clk rate,
 	beq	return_to_sdram		@ return to SDRAM code, otherwise,
 	bl	configure_sdrc		@ reprogram SDRC regs now
-	mov	r12, r5
+	mov	r12, r2
 	bl	wait_clk_stable		@ wait for SDRC to stabilize
 return_to_sdram:
 	isb				@ prevent speculative exec past here
@@ -149,7 +180,7 @@ configure_core_dpll:
 	ldr	r12, [r11]
 	ldr	r10, core_m2_mask_val	@ modify m2 for core dpll
 	and	r12, r12, r10
-	orr	r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
+	orr	r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
 	str	r12, [r11]
 	ldr	r12, [r11]		@ posted-write barrier for CM
 	bx	lr
@@ -187,15 +218,34 @@ wait_dll_unlock:
 	bne	wait_dll_unlock
 	bx	lr
 configure_sdrc:
-	ldr	r11, omap3_sdrc_rfr_ctrl
-	str	r0, [r11]
-	ldr	r11, omap3_sdrc_actim_ctrla
-	str	r1, [r11]
-	ldr	r11, omap3_sdrc_actim_ctrlb
-	str	r2, [r11]
+	ldr	r12, omap_sdrc_rfr_ctrl_0_val	@ fetch value from SRAM
+	ldr	r11, omap3_sdrc_rfr_ctrl_0	@ fetch addr from SRAM
+	str	r12, [r11]			@ store
+	ldr	r12, omap_sdrc_actim_ctrl_a_0_val
+	ldr	r11, omap3_sdrc_actim_ctrl_a_0
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_actim_ctrl_b_0_val
+	ldr	r11, omap3_sdrc_actim_ctrl_b_0
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_mr_0_val
 	ldr	r11, omap3_sdrc_mr_0
-	str	r6, [r11]
-	ldr	r6, [r11]		@ posted-write barrier for SDRC
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_rfr_ctrl_1_val
+	cmp	r12, #0			@ if SDRC_RFR_CTRL_1 is 0,
+	beq	skip_cs1_prog		@  do not program cs1 params
+	ldr	r11, omap3_sdrc_rfr_ctrl_1
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_actim_ctrl_a_1_val
+	ldr	r11, omap3_sdrc_actim_ctrl_a_1
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_actim_ctrl_b_1_val
+	ldr	r11, omap3_sdrc_actim_ctrl_b_1
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_mr_1_val
+	ldr	r11, omap3_sdrc_mr_1
+	str	r12, [r11]
+skip_cs1_prog:
+	ldr	r12, [r11]		@ posted-write barrier for SDRC
 	bx	lr
 
 omap3_sdrc_power:
@@ -206,14 +256,40 @@ omap3_cm_idlest1_core:
 	.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST)
 omap3_cm_iclken1_core:
 	.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1)
-omap3_sdrc_rfr_ctrl:
+
+omap3_sdrc_rfr_ctrl_0:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0)
-omap3_sdrc_actim_ctrla:
+omap3_sdrc_rfr_ctrl_1:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1)
+omap3_sdrc_actim_ctrl_a_0:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0)
-omap3_sdrc_actim_ctrlb:
+omap3_sdrc_actim_ctrl_a_1:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1)
+omap3_sdrc_actim_ctrl_b_0:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0)
+omap3_sdrc_actim_ctrl_b_1:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1)
 omap3_sdrc_mr_0:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_MR_0)
+omap3_sdrc_mr_1:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_MR_1)
+omap_sdrc_rfr_ctrl_0_val:
+	.word 0xDEADBEEF
+omap_sdrc_rfr_ctrl_1_val:
+	.word 0xDEADBEEF
+omap_sdrc_actim_ctrl_a_0_val:
+	.word 0xDEADBEEF
+omap_sdrc_actim_ctrl_a_1_val:
+	.word 0xDEADBEEF
+omap_sdrc_actim_ctrl_b_0_val:
+	.word 0xDEADBEEF
+omap_sdrc_actim_ctrl_b_1_val:
+	.word 0xDEADBEEF
+omap_sdrc_mr_0_val:
+	.word 0xDEADBEEF
+omap_sdrc_mr_1_val:
+	.word 0xDEADBEEF
+
 omap3_sdrc_dlla_status:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS)
 omap3_sdrc_dlla_ctrl:
@@ -223,3 +299,4 @@ core_m2_mask_val:
 
 ENTRY(omap3_sram_configure_core_dpll_sz)
 	.word	. - omap3_sram_configure_core_dpll
+