Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC board specific changes from Arnd Bergmann:
 "These updates are all for board specific code, including

   - defconfig updates for shmobile, davinci, bcm2835, imx, omap and
     tegra

   - SD/MMC and I2C support on bcm2835 (Raspberry PI)

   - minor updates for PXA

   - shmobile updates to GPIO usage in board files

   - More things in OMAP board files are moved over to device tree
     probing

   - Better support for audio devices on some OMAP platforms"

* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
  ARM: imx_v4_v5_defconfig: Add VPU support
  ARM: imx: configs: enable netfilter support
  ARM: OMAP2+: Fix twl section warnings related to omap_twl4030_audio_init
  ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
  RX-51: Register twl4030-madc device
  RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
  ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
  ARM: OMAP1: nokia770: enable CBUS/Retu
  ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
  ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
  ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
  ARM: OMAP2+: craneboard: support the TPS65910 PMU
  ARM: OMAP2+: craneboard: support NAND device
  ARM: OMAP3: cm-t3517: add MMC support
  ARM: OMAP2+: Remove apollon board support
  ARM: shmobile: armadillo800eva: set clock rates before timer init
  ARM: tegra: defconfig updates
  ARM: shmobile: mackerel: Use gpio_request_one()
  ARM: shmobile: kzm9g: Use gpio_request_one()
  ARM: shmobile: bonito: Use gpio_request_one()
  ...

18 files changed, 234 insertions, 400 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index c3c033f283a..22ad24e9496 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -188,12 +188,6 @@ config MACH_OMAP_H4
 	select OMAP_DEBUG_DEVICES
 	select OMAP_PACKAGE_ZAF
 
-config MACH_OMAP_APOLLON
-	bool "OMAP 2420 Apollon board"
-	depends on SOC_OMAP2420
-	default y
-	select OMAP_PACKAGE_ZAC
-
 config MACH_OMAP_2430SDP
 	bool "OMAP 2430 SDP board"
 	depends on SOC_OMAP2430
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 65fb6fb38ca..ff528df7011 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -223,7 +223,6 @@ endif
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
 obj-$(CONFIG_MACH_OMAP_2430SDP)		+= board-2430sdp.o
-obj-$(CONFIG_MACH_OMAP_APOLLON)		+= board-apollon.o
 obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o
 obj-$(CONFIG_MACH_DEVKIT8000)     	+= board-devkit8000.o
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 15a3914ab49..ce812decfac 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -25,6 +25,7 @@
 #include <linux/gpio.h>
 #include <linux/mmc/host.h>
 #include <linux/platform_data/spi-omap2-mcspi.h>
+#include <linux/platform_data/omap-twl4030.h>
 #include <linux/usb/phy.h>
 
 #include <asm/mach-types.h>
@@ -210,6 +211,19 @@ static struct omap2_hsmmc_info mmc[] = {
 	{}	/* Terminator */
 };
 
+static struct omap_tw4030_pdata omap_twl4030_audio_data = {
+	.voice_connected = true,
+	.custom_routing	= true,
+
+	.has_hs		= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
+	.has_hf		= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
+
+	.has_mainmic	= true,
+	.has_submic	= true,
+	.has_hsmic	= true,
+	.has_linein	= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
+};
+
 static int sdp3430_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
@@ -226,6 +240,9 @@ static int sdp3430_twl_gpio_setup(struct device *dev,
 	/* gpio + 15 is "sub_lcd_nRST" (output) */
 	gpio_request_one(gpio + 15, GPIOF_OUT_INIT_LOW, "sub_lcd_nRST");
 
+	omap_twl4030_audio_data.jack_detect = gpio + 2;
+	omap_twl4030_audio_init("SDP3430", &omap_twl4030_audio_data);
+
 	return 0;
 }
 
@@ -383,6 +400,9 @@ static int __init omap3430_i2c_init(void)
 	sdp3430_twldata.vpll2->constraints.apply_uV = true;
 	sdp3430_twldata.vpll2->constraints.name = "VDVI";
 
+	sdp3430_twldata.audio->codec->hs_extmute = 1;
+	sdp3430_twldata.audio->codec->hs_extmute_gpio = -EINVAL;
+
 	omap3_pmic_init("twl4030", &sdp3430_twldata);
 
 	/* i2c2 on camera connector (for sensor control) and optional isp1301 */
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 508e2752b7d..35f3ad0cb7c 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -24,8 +24,10 @@
 #include <linux/gpio_keys.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/fixed.h>
+#include <linux/pwm.h>
 #include <linux/leds.h>
 #include <linux/leds_pwm.h>
+#include <linux/pwm_backlight.h>
 #include <linux/irqchip/arm-gic.h>
 #include <linux/platform_data/omap4-keypad.h>
 #include <linux/usb/musb.h>
@@ -257,10 +259,20 @@ static struct gpio_led_platform_data sdp4430_led_data = {
 	.num_leds	= ARRAY_SIZE(sdp4430_gpio_leds),
 };
 
+static struct pwm_lookup sdp4430_pwm_lookup[] = {
+	PWM_LOOKUP("twl-pwm", 0, "leds_pwm", "omap4::keypad"),
+	PWM_LOOKUP("twl-pwm", 1, "pwm-backlight", NULL),
+	PWM_LOOKUP("twl-pwmled", 0, "leds_pwm", "omap4:green:chrg"),
+};
+
 static struct led_pwm sdp4430_pwm_leds[] = {
 	{
+		.name		= "omap4::keypad",
+		.max_brightness	= 127,
+		.pwm_period_ns	= 7812500,
+	},
+	{
 		.name		= "omap4:green:chrg",
-		.pwm_id		= 1,
 		.max_brightness	= 255,
 		.pwm_period_ns	= 7812500,
 	},
@@ -279,6 +291,20 @@ static struct platform_device sdp4430_leds_pwm = {
 	},
 };
 
+static struct platform_pwm_backlight_data sdp4430_backlight_data = {
+	.max_brightness = 127,
+	.dft_brightness = 127,
+	.pwm_period_ns = 7812500,
+};
+
+static struct platform_device sdp4430_backlight_pwm = {
+	.name   = "pwm-backlight",
+	.id     = -1,
+	.dev    = {
+		.platform_data = &sdp4430_backlight_data,
+	},
+};
+
 static int omap_prox_activate(struct device *dev)
 {
 	gpio_set_value(OMAP4_SFH7741_ENABLE_GPIO , 1);
@@ -413,6 +439,7 @@ static struct platform_device *sdp4430_devices[] __initdata = {
 	&sdp4430_gpio_keys_device,
 	&sdp4430_leds_gpio,
 	&sdp4430_leds_pwm,
+	&sdp4430_backlight_pwm,
 	&sdp4430_vbat,
 	&sdp4430_dmic_codec,
 	&sdp4430_abe_audio,
@@ -709,6 +736,7 @@ static void __init omap_4430sdp_init(void)
 				ARRAY_SIZE(sdp4430_spi_board_info));
 	}
 
+	pwm_add_table(sdp4430_pwm_lookup, ARRAY_SIZE(sdp4430_pwm_lookup));
 	status = omap4_keyboard_init(&sdp4430_keypad_data, &keypad_data);
 	if (status)
 		pr_err("Keypad initialization failed: %d\n", status);
diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 52cc2c59731..7d3358b2e59 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -20,12 +20,18 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/gpio.h>
+#include <linux/mfd/tps65910.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
 #include "common.h"
+#include "common-board-devices.h"
+#include "board-flash.h"
 
 #include "am35xx-emac.h"
 #include "mux.h"
@@ -36,6 +42,7 @@
 
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
+	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #endif
@@ -51,6 +58,54 @@ static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 	.reset_gpio_port[2]  = -EINVAL
 };
 
+static struct mtd_partition crane_nand_partitions[] = {
+	{
+		.name		= "X-Loader",
+		.offset		= 0,
+		.size		= 4 * NAND_BLOCK_SIZE,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	{
+		.name		= "U-Boot",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 14 * NAND_BLOCK_SIZE,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	{
+		.name		= "U-Boot Env",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 2 * NAND_BLOCK_SIZE,
+	},
+	{
+		.name		= "Kernel",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 40 * NAND_BLOCK_SIZE,
+	},
+	{
+		.name		= "File System",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct tps65910_board tps65910_pdata = {
+	.irq = 7 + OMAP_INTC_START,
+	.en_ck32k_xtal = true,
+};
+
+static struct i2c_board_info __initdata tps65910_board_info[] = {
+	{
+		I2C_BOARD_INFO("tps65910", 0x2d),
+		.platform_data = &tps65910_pdata,
+	},
+};
+
+static void __init am3517_crane_i2c_init(void)
+{
+	omap_register_i2c_bus(1, 2600, tps65910_board_info,
+			ARRAY_SIZE(tps65910_board_info));
+}
+
 static void __init am3517_crane_init(void)
 {
 	int ret;
@@ -58,6 +113,10 @@ static void __init am3517_crane_init(void)
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
+	board_nand_init(crane_nand_partitions,
+			ARRAY_SIZE(crane_nand_partitions), 0,
+			NAND_BUSWIDTH_16, NULL);
+	am3517_crane_i2c_init();
 
 	/* Configure GPIO for EHCI port */
 	if (omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT)) {
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
deleted file mode 100644
index 3a6ca74709a..00000000000
--- a/arch/arm/mach-omap2/board-apollon.c
+++ /dev/null
@@ -1,342 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-apollon.c
- *
- * Copyright (C) 2005,2006 Samsung Electronics
- * Author: Kyungmin Park <kyungmin.park@samsung.com>
- *
- * Modified from mach-omap/omap2/board-h4.c
- *
- * Code for apollon OMAP2 board. Should work on many OMAP2 systems where
- * the bootloader passes the board-specific data to the kernel.
- * Do not put any board specific code to this file; create a new machine
- * type if you need custom low-level initializations.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/onenand.h>
-#include <linux/delay.h>
-#include <linux/leds.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/smc91x.h>
-#include <linux/gpio.h>
-#include <linux/platform_data/leds-omap.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-
-#include <video/omapdss.h>
-#include <video/omap-panel-generic-dpi.h>
-
-#include "mux.h"
-#include "control.h"
-
-/* LED & Switch macros */
-#define LED0_GPIO13		13
-#define LED1_GPIO14		14
-#define LED2_GPIO15		15
-#define SW_ENTER_GPIO16		16
-#define SW_UP_GPIO17		17
-#define SW_DOWN_GPIO58		58
-
-#define APOLLON_FLASH_CS	0
-#define APOLLON_ETH_CS		1
-#define APOLLON_ETHR_GPIO_IRQ	74
-
-static struct mtd_partition apollon_partitions[] = {
-	{
-		.name		= "X-Loader + U-Boot",
-		.offset		= 0,
-		.size		= SZ_128K,
-		.mask_flags	= MTD_WRITEABLE,
-	},
-	{
-		.name		= "params",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_128K,
-	},
-	{
-		.name		= "kernel",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_2M,
-	},
-	{
-		.name		= "rootfs",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_16M,
-	},
-	{
-		.name		= "filesystem00",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_32M,
-	},
-	{
-		.name		= "filesystem01",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct onenand_platform_data apollon_flash_data = {
-	.parts		= apollon_partitions,
-	.nr_parts	= ARRAY_SIZE(apollon_partitions),
-};
-
-static struct resource apollon_flash_resource[] = {
-	[0] = {
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device apollon_onenand_device = {
-	.name		= "onenand-flash",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &apollon_flash_data,
-	},
-	.num_resources	= ARRAY_SIZE(apollon_flash_resource),
-	.resource	= apollon_flash_resource,
-};
-
-static void __init apollon_flash_init(void)
-{
-	unsigned long base;
-
-	if (gpmc_cs_request(APOLLON_FLASH_CS, SZ_128K, &base) < 0) {
-		printk(KERN_ERR "Cannot request OneNAND GPMC CS\n");
-		return;
-	}
-	apollon_flash_resource[0].start = base;
-	apollon_flash_resource[0].end   = base + SZ_128K - 1;
-}
-
-static struct smc91x_platdata appolon_smc91x_info = {
-	.flags	= SMC91X_USE_16BIT | SMC91X_NOWAIT,
-	.leda	= RPC_LED_100_10,
-	.ledb	= RPC_LED_TX_RX,
-};
-
-static struct resource apollon_smc91x_resources[] = {
-	[0] = {
-		.flags  = IORESOURCE_MEM,
-	},
-	[1] = {
-		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
-	},
-};
-
-static struct platform_device apollon_smc91x_device = {
-	.name		= "smc91x",
-	.id		= -1,
-	.dev	= {
-		.platform_data	= &appolon_smc91x_info,
-	},
-	.num_resources	= ARRAY_SIZE(apollon_smc91x_resources),
-	.resource	= apollon_smc91x_resources,
-};
-
-static struct omap_led_config apollon_led_config[] = {
-	{
-		.cdev	= {
-			.name	= "apollon:led0",
-		},
-		.gpio	= LED0_GPIO13,
-	},
-	{
-		.cdev	= {
-			.name	= "apollon:led1",
-		},
-		.gpio	= LED1_GPIO14,
-	},
-	{
-		.cdev	= {
-			.name	= "apollon:led2",
-		},
-		.gpio	= LED2_GPIO15,
-	},
-};
-
-static struct omap_led_platform_data apollon_led_data = {
-	.nr_leds	= ARRAY_SIZE(apollon_led_config),
-	.leds		= apollon_led_config,
-};
-
-static struct platform_device apollon_led_device = {
-	.name		= "omap-led",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &apollon_led_data,
-	},
-};
-
-static struct platform_device *apollon_devices[] __initdata = {
-	&apollon_onenand_device,
-	&apollon_smc91x_device,
-	&apollon_led_device,
-};
-
-static inline void __init apollon_init_smc91x(void)
-{
-	unsigned long base;
-
-	unsigned int rate;
-	struct clk *gpmc_fck;
-	int eth_cs;
-	int err;
-
-	gpmc_fck = clk_get(NULL, "gpmc_fck");	/* Always on ENABLE_ON_INIT */
-	if (IS_ERR(gpmc_fck)) {
-		WARN_ON(1);
-		return;
-	}
-
-	clk_prepare_enable(gpmc_fck);
-	rate = clk_get_rate(gpmc_fck);
-
-	eth_cs = APOLLON_ETH_CS;
-
-	/* Make sure CS1 timings are correct */
-	gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
-
-	if (rate >= 160000000) {
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
-	} else if (rate >= 130000000) {
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
-	} else {/* rate = 100000000 */
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
-	}
-
-	if (gpmc_cs_request(APOLLON_ETH_CS, SZ_16M, &base) < 0) {
-		printk(KERN_ERR "Failed to request GPMC CS for smc91x\n");
-		goto out;
-	}
-	apollon_smc91x_resources[0].start = base + 0x300;
-	apollon_smc91x_resources[0].end   = base + 0x30f;
-	udelay(100);
-
-	omap_mux_init_gpio(APOLLON_ETHR_GPIO_IRQ, 0);
-	err = gpio_request_one(APOLLON_ETHR_GPIO_IRQ, GPIOF_IN, "SMC91x irq");
-	if (err) {
-		printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
-			APOLLON_ETHR_GPIO_IRQ);
-		gpmc_cs_free(APOLLON_ETH_CS);
-	}
-out:
-	clk_disable_unprepare(gpmc_fck);
-	clk_put(gpmc_fck);
-}
-
-static struct panel_generic_dpi_data apollon_panel_data = {
-	.name			= "apollon",
-};
-
-static struct omap_dss_device apollon_lcd_device = {
-	.name			= "lcd",
-	.driver_name		= "generic_dpi_panel",
-	.type			= OMAP_DISPLAY_TYPE_DPI,
-	.phy.dpi.data_lines	= 18,
-	.data			= &apollon_panel_data,
-};
-
-static struct omap_dss_device *apollon_dss_devices[] = {
-	&apollon_lcd_device,
-};
-
-static struct omap_dss_board_info apollon_dss_data = {
-	.num_devices	= ARRAY_SIZE(apollon_dss_devices),
-	.devices	= apollon_dss_devices,
-	.default_device	= &apollon_lcd_device,
-};
-
-static struct gpio apollon_gpio_leds[] __initdata = {
-	{ LED0_GPIO13, GPIOF_OUT_INIT_LOW, "LED0" }, /* LED0 - AA10 */
-	{ LED1_GPIO14, GPIOF_OUT_INIT_LOW, "LED1" }, /* LED1 - AA6  */
-	{ LED2_GPIO15, GPIOF_OUT_INIT_LOW, "LED2" }, /* LED2 - AA4  */
-};
-
-static void __init apollon_led_init(void)
-{
-	omap_mux_init_signal("vlynq_clk.gpio_13", 0);
-	omap_mux_init_signal("vlynq_rx1.gpio_14", 0);
-	omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
-
-	gpio_request_array(apollon_gpio_leds, ARRAY_SIZE(apollon_gpio_leds));
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init omap_apollon_init(void)
-{
-	u32 v;
-
-	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
-
-	apollon_init_smc91x();
-	apollon_led_init();
-	apollon_flash_init();
-
-	/* REVISIT: where's the correct place */
-	omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);
-
-	/* LCD PWR_EN */
-	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
-
-	/* Use Internal loop-back in MMC/SDIO Module Input Clock selection */
-	v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
-	v |= (1 << 24);
-	omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
-
-	/*
- 	 * Make sure the serial ports are muxed on at this point.
-	 * You have to mux them off in device drivers later on
-	 * if not needed.
-	 */
-	apollon_smc91x_resources[1].start = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
-	apollon_smc91x_resources[1].end = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
-	platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
-	omap_serial_init();
-	omap_sdrc_init(NULL, NULL);
-	omap_display_init(&apollon_dss_data);
-}
-
-MACHINE_START(OMAP_APOLLON, "OMAP24xx Apollon")
-	/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap242x_map_io,
-	.init_early	= omap2420_init_early,
-	.init_irq	= omap2_init_irq,
-	.handle_irq	= omap2_intc_handle_irq,
-	.init_machine	= omap_apollon_init,
-	.init_late	= omap2420_init_late,
-	.init_time	= omap2_sync32k_timer_init,
-	.restart	= omap2xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index 10054e3c348..af2bb219e21 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -723,7 +723,7 @@ static void __init cm_t3x_common_init(void)
 	cm_t35_init_ethernet();
 	cm_t35_init_led();
 	cm_t35_init_display();
-	omap_twl4030_audio_init("cm-t3x");
+	omap_twl4030_audio_init("cm-t3x", NULL);
 
 	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(NULL);
diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c
index 5e54f565a29..a66da808cc4 100644
--- a/arch/arm/mach-omap2/board-cm-t3517.c
+++ b/arch/arm/mach-omap2/board-cm-t3517.c
@@ -32,6 +32,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
+#include <linux/mmc/host.h>
 #include <linux/can/platform/ti_hecc.h>
 
 #include <asm/mach-types.h>
@@ -46,6 +47,7 @@
 
 #include "mux.h"
 #include "control.h"
+#include "hsmmc.h"
 #include "common-board-devices.h"
 #include "am35xx-emac.h"
 #include "gpmc-nand.h"
@@ -121,6 +123,26 @@ static void cm_t3517_init_hecc(void)
 static inline void cm_t3517_init_hecc(void) {}
 #endif
 
+#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
+static struct omap2_hsmmc_info cm_t3517_mmc[] = {
+	{
+		.mmc		= 1,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= 144,
+		.gpio_wp	= 59,
+	},
+	{
+		.mmc		= 2,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+	},
+	{}	/* Terminator */
+};
+#else
+#define cm_t3517_mmc NULL
+#endif
+
 #if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE)
 #define RTC_IO_GPIO		(153)
 #define RTC_WR_GPIO		(154)
@@ -271,6 +293,10 @@ static struct omap_board_mux board_mux[] __initdata = {
 	/* CM-T3517 USB HUB nRESET */
 	OMAP3_MUX(MCBSP4_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
 
+	/* CD - GPIO144 and WP - GPIO59 for MMC1 - SB-T35 */
+	OMAP3_MUX(UART2_CTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(GPMC_CLK, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
+
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #endif
@@ -286,6 +312,7 @@ static void __init cm_t3517_init(void)
 	cm_t3517_init_usbh();
 	cm_t3517_init_hecc();
 	am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1);
+	omap_hsmmc_init(cm_t3517_mmc);
 }
 
 MACHINE_START(CM_T3517, "Compulab CM-T3517")
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 4dadb0b7b80..53056c3b083 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -629,7 +629,7 @@ static void __init devkit8000_init(void)
 	board_nand_init(devkit8000_nand_partitions,
 			ARRAY_SIZE(devkit8000_nand_partitions), NAND_CS,
 			NAND_BUSWIDTH_16, NULL);
-	omap_twl4030_audio_init("omap3beagle");
+	omap_twl4030_audio_init("omap3beagle", NULL);
 
 	/* Ensure SDRC pins are mux'd for self-refresh */
 	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index c10738a067c..bf92678a01d 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -301,20 +301,20 @@ static struct omap2_hsmmc_info mmc[] = {
 
 static struct gpio_led igep_gpio_leds[] = {
 	[0] = {
-		.name			= "gpio-led:red:d0",
-		.default_trigger	= "default-off"
+		.name			= "omap3:red:user0",
+		.default_state		= 0,
 	},
 	[1] = {
-		.name			= "gpio-led:green:d0",
-		.default_trigger	= "default-off",
+		.name			= "omap3:green:boot",
+		.default_state		= 1,
 	},
 	[2] = {
-		.name			= "gpio-led:red:d1",
-		.default_trigger	= "default-off",
+		.name			= "omap3:red:user1",
+		.default_state		= 0,
 	},
 	[3] = {
-		.name			= "gpio-led:green:d1",
-		.default_trigger	= "heartbeat",
+		.name			= "omap3:green:user1",
+		.default_state		= 0,
 		.gpio			= -EINVAL, /* gets replaced */
 		.active_low		= 1,
 	},
@@ -631,7 +631,7 @@ static void __init igep_init(void)
 
 	igep_flash_init();
 	igep_leds_init();
-	omap_twl4030_audio_init("igep2");
+	omap_twl4030_audio_init("igep2", NULL);
 
 	/*
 	 * WLAN-BT combo module from MuRata which has a Marvell WLAN
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 70bc1fc808c..c3558f93d42 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -20,6 +20,8 @@
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/leds.h>
+#include <linux/pwm.h>
+#include <linux/leds_pwm.h>
 #include <linux/gpio.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
@@ -56,6 +58,32 @@
 
 #define	NAND_CS	0
 
+static struct pwm_lookup pwm_lookup[] = {
+	/* LEDB -> PMU_STAT */
+	PWM_LOOKUP("twl-pwmled", 1, "leds_pwm", "beagleboard::pmu_stat"),
+};
+
+static struct led_pwm pwm_leds[] = {
+	{
+		.name		= "beagleboard::pmu_stat",
+		.max_brightness	= 127,
+		.pwm_period_ns	= 7812500,
+	},
+};
+
+static struct led_pwm_platform_data pwm_data = {
+	.num_leds	= ARRAY_SIZE(pwm_leds),
+	.leds		= pwm_leds,
+};
+
+static struct platform_device leds_pwm = {
+	.name	= "leds_pwm",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &pwm_data,
+	},
+};
+
 /*
  * OMAP3 Beagle revision
  * Run time detection of Beagle revision is done by reading GPIO.
@@ -293,9 +321,6 @@ static int beagle_twl_gpio_setup(struct device *dev,
 	gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
 			"nEN_USB_PWR");
 
-	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
 	return 0;
 }
 
@@ -377,11 +402,6 @@ static struct gpio_led gpio_leds[] = {
 		.default_trigger	= "mmc0",
 		.gpio			= 149,
 	},
-	{
-		.name			= "beagleboard::pmu_stat",
-		.gpio			= -EINVAL,	/* gets replaced */
-		.active_low		= true,
-	},
 };
 
 static struct gpio_led_platform_data gpio_led_info = {
@@ -429,6 +449,7 @@ static struct platform_device *omap3_beagle_devices[] __initdata = {
 	&leds_gpio,
 	&keys_gpio,
 	&madc_hwmon,
+	&leds_pwm,
 };
 
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
@@ -526,7 +547,7 @@ static void __init omap3_beagle_init(void)
 	board_nand_init(omap3beagle_nand_partitions,
 			ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS,
 			NAND_BUSWIDTH_16, NULL);
-	omap_twl4030_audio_init("omap3beagle");
+	omap_twl4030_audio_init("omap3beagle", NULL);
 
 	/* Ensure msecure is mux'd to be able to set the RTC. */
 	omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
@@ -534,6 +555,8 @@ static void __init omap3_beagle_init(void)
 	/* Ensure SDRC pins are mux'd for self-refresh */
 	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
 	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
+
+	pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
 }
 
 MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 8258a78c3df..48789e0bb91 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -746,7 +746,7 @@ static void __init omap3_evm_init(void)
 	omap3evm_init_smsc911x();
 	omap3_evm_display_init();
 	omap3_evm_wl12xx_init();
-	omap_twl4030_audio_init("omap3evm");
+	omap_twl4030_audio_init("omap3evm", NULL);
 }
 
 MACHINE_START(OMAP3EVM, "OMAP3 EVM")
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 1bcf39671c3..86bab51154e 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -508,7 +508,7 @@ static void __init overo_init(void)
 	overo_display_init();
 	overo_init_led();
 	overo_init_keys();
-	omap_twl4030_audio_init("overo");
+	omap_twl4030_audio_init("overo", NULL);
 
 	/* Ensure SDRC pins are mux'd for self-refresh */
 	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index f3d075baebb..c26d441ca4f 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -162,30 +162,39 @@ static struct tsl2563_platform_data rx51_tsl2563_platform_data = {
 #if defined(CONFIG_LEDS_LP5523) || defined(CONFIG_LEDS_LP5523_MODULE)
 static struct lp5523_led_config rx51_lp5523_led_config[] = {
 	{
+		.name		= "lp5523:kb1",
 		.chan_nr	= 0,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb2",
 		.chan_nr	= 1,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb3",
 		.chan_nr	= 2,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb4",
 		.chan_nr	= 3,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:b",
 		.chan_nr	= 4,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:g",
 		.chan_nr	= 5,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:r",
 		.chan_nr	= 6,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb5",
 		.chan_nr	= 7,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb6",
 		.chan_nr	= 8,
 		.led_current	= 50,
 	}
@@ -1253,6 +1262,16 @@ static void __init rx51_init_lirc(void)
 }
 #endif
 
+static struct platform_device madc_hwmon = {
+	.name	= "twl4030_madc_hwmon",
+	.id	= -1,
+};
+
+static void __init rx51_init_twl4030_hwmon(void)
+{
+	platform_device_register(&madc_hwmon);
+}
+
 void __init rx51_peripherals_init(void)
 {
 	rx51_i2c_init();
@@ -1272,5 +1291,6 @@ void __init rx51_peripherals_init(void)
 		omap_hsmmc_init(mmc);
 
 	rx51_charger_init();
+	rx51_init_twl4030_hwmon();
 }
 
diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c
index dc5498b1b3a..cdc0c102186 100644
--- a/arch/arm/mach-omap2/board-zoom-peripherals.c
+++ b/arch/arm/mach-omap2/board-zoom-peripherals.c
@@ -20,6 +20,7 @@
 #include <linux/wl12xx.h>
 #include <linux/mmc/host.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/omap-twl4030.h>
 #include <linux/usb/phy.h>
 
 #include <asm/mach-types.h>
@@ -35,11 +36,9 @@
 #include "common-board-devices.h"
 
 #define OMAP_ZOOM_WLAN_PMENA_GPIO	(101)
-#define ZOOM2_HEADSET_EXTMUTE_GPIO	(153)
+#define OMAP_ZOOM_TSC2004_IRQ_GPIO	(153)
 #define OMAP_ZOOM_WLAN_IRQ_GPIO		(162)
 
-#define LCD_PANEL_ENABLE_GPIO		(7 + OMAP_MAX_GPIO_LINES)
-
 /* Zoom2 has Qwerty keyboard*/
 static uint32_t board_keymap[] = {
 	KEY(0, 0, KEY_E),
@@ -227,22 +226,31 @@ static struct omap2_hsmmc_info mmc[] = {
 	{}      /* Terminator */
 };
 
+static struct omap_tw4030_pdata omap_twl4030_audio_data = {
+	.voice_connected = true,
+	.custom_routing	= true,
+
+	.has_hs		= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
+	.has_hf		= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
+
+	.has_mainmic	= true,
+	.has_submic	= true,
+	.has_hsmic	= true,
+	.has_linein	= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
+};
+
 static int zoom_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
-	int ret;
-
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
 	mmc[0].gpio_cd = gpio + 0;
 	omap_hsmmc_late_init(mmc);
 
-	ret = gpio_request_one(LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW,
-			       "lcd enable");
-	if (ret)
-		pr_err("Failed to get LCD_PANEL_ENABLE_GPIO (gpio%d).\n",
-				LCD_PANEL_ENABLE_GPIO);
+	/* Audio setup */
+	omap_twl4030_audio_data.jack_detect = gpio + 2;
+	omap_twl4030_audio_init("Zoom2", &omap_twl4030_audio_data);
 
-	return ret;
+	return 0;
 }
 
 static struct twl4030_gpio_platform_data zoom_gpio_data = {
@@ -265,14 +273,9 @@ static int __init omap_i2c_init(void)
 			TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO,
 			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
 
-	if (machine_is_omap_zoom2()) {
-		struct twl4030_codec_data *codec_data;
-		codec_data = zoom_twldata.audio->codec;
+	if (machine_is_omap_zoom2())
+		zoom_twldata.audio->codec->ramp_delay_value = 3; /* 161 ms */
 
-		codec_data->ramp_delay_value = 3;	/* 161 ms */
-		codec_data->hs_extmute = 1;
-		codec_data->hs_extmute_gpio = ZOOM2_HEADSET_EXTMUTE_GPIO;
-	}
 	omap_pmic_init(1, 2400, "twl5030", 7 + OMAP_INTC_START, &zoom_twldata);
 	omap_register_i2c_bus(2, 400, NULL, 0);
 	omap_register_i2c_bus(3, 400, NULL, 0);
diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
index 8d70bd03c5d..e4b16c8efe8 100644
--- a/arch/arm/mach-omap2/gpmc.c
+++ b/arch/arm/mach-omap2/gpmc.c
@@ -790,9 +790,6 @@ static int gpmc_mem_init(void)
 	 * even if we didn't boot from ROM.
 	 */
 	boot_rom_space = BOOT_ROM_SPACE;
-	/* In apollon the CS0 is mapped as 0x0000 0000 */
-	if (machine_is_omap_apollon())
-		boot_rom_space = 0;
 	gpmc_mem_root.start = GPMC_MEM_START + boot_rom_space;
 	gpmc_mem_root.end = GPMC_MEM_END;
 
diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c
index 6a7aec6d117..51e138cc539 100644
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -529,24 +529,29 @@ void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
 	defined(CONFIG_SND_OMAP_SOC_OMAP_TWL4030_MODULE)
 #include <linux/platform_data/omap-twl4030.h>
 
+/* Commonly used configuration */
 static struct omap_tw4030_pdata omap_twl4030_audio_data;
 
 static struct platform_device audio_device = {
 	.name		= "omap-twl4030",
 	.id		= -1,
-	.dev = {
-		.platform_data = &omap_twl4030_audio_data,
-	},
 };
 
-void __init omap_twl4030_audio_init(char *card_name)
+void omap_twl4030_audio_init(char *card_name,
+				    struct omap_tw4030_pdata *pdata)
 {
-	omap_twl4030_audio_data.card_name = card_name;
+	if (!pdata)
+		pdata = &omap_twl4030_audio_data;
+
+	pdata->card_name = card_name;
+
+	audio_device.dev.platform_data = pdata;
 	platform_device_register(&audio_device);
 }
 
 #else /* SOC_OMAP_TWL4030 */
-void __init omap_twl4030_audio_init(char *card_name)
+void omap_twl4030_audio_init(char *card_name,
+				    struct omap_tw4030_pdata *pdata)
 {
 	return;
 }
diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h
index dcfbad5ac47..24b65d081b6 100644
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -32,6 +32,7 @@
 
 struct twl4030_platform_data;
 struct twl6040_platform_data;
+struct omap_tw4030_pdata;
 struct i2c_board_info;
 
 void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq,
@@ -60,6 +61,6 @@ void omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
 void omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
 			   u32 pdata_flags, u32 regulators_flags);
 
-void omap_twl4030_audio_init(char *card_name);
+void omap_twl4030_audio_init(char *card_name, struct omap_tw4030_pdata *pdata);
 
 #endif /* __OMAP_PMIC_COMMON__ */