Merge tag 'omap-board-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards

Board specific changes for omap.

Note that these are based on omap-pm-regulator-for-v3.5 as
both branches are adding twl regulators.

By Paul Gortmaker (8) and others
via Linus Torvalds (38) and others
* tag 'omap-board-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  OMAP: omap4panda: Use common configuration for V1V8, V2V1 supplies
  OMAP: 4430SDP: Use common configuration for V1V8, V2V1 supplies
  OMAP4: twl-common: Add twl6030 V1V8, V2V1 SMPS common configuration
  ARM: OMAP: Mark Beagleboard-xM MMC bus as 4-bit
  Add MSUB support for the LogicPD OMAP3530 DevKits
  ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer
  ARM: OMAP2+: craneboard: register emac device
  ARM: OMAP4: board-omap4panda: Register platform device for HDMI audio codec
  ARM: OMAP4: board-4430sdp: Register platform device for HDMI audio codec
  ARM: OMAP: devices: Register platform devices for HDMI audio
  ARM: OMAP3: igep0020: Add support for Micron NAND Flash storage memory
  ARM: OMAP2+: nand: Make board_onenand_init() visible to board code
  ARM: OMAP3: cm-t35: add support for power off
  ARM: OMAP: WiLink platform data for the PandaBoard
  ARM: OMAP2PLUS: Enable HIGHMEM
  ARM: OMAP: omap2plus_defconfig: Enable ehci-omap and sms95xx support

Signed-off-by: Olof Johansson <olof@lixom.net>

16 files changed, 442 insertions, 55 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 8141b76283a..964ee67a3b7 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -17,6 +17,7 @@ config ARCH_OMAP2PLUS_TYPICAL
 	select MENELAUS if ARCH_OMAP2
 	select TWL4030_CORE if ARCH_OMAP3 || ARCH_OMAP4
 	select TWL4030_POWER if ARCH_OMAP3 || ARCH_OMAP4
+	select HIGHMEM
 	help
 	  Compile a kernel suitable for booting most boards
 
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 130ab00c09a..2e5066458f7 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -384,6 +384,11 @@ static struct platform_device sdp4430_dmic_codec = {
 	.id	= -1,
 };
 
+static struct platform_device sdp4430_hdmi_audio_codec = {
+	.name	= "hdmi-audio-codec",
+	.id	= -1,
+};
+
 static struct omap_abe_twl6040_data sdp4430_abe_audio_data = {
 	.card_name = "SDP4430",
 	.has_hs		= ABE_TWL6040_LEFT | ABE_TWL6040_RIGHT,
@@ -418,6 +423,7 @@ static struct platform_device *sdp4430_devices[] __initdata = {
 	&sdp4430_vbat,
 	&sdp4430_dmic_codec,
 	&sdp4430_abe_audio,
+	&sdp4430_hdmi_audio_codec,
 };
 
 static struct omap_musb_board_data musb_board_data = {
@@ -615,7 +621,9 @@ static int __init omap4_i2c_init(void)
 			TWL_COMMON_REGULATOR_VANA |
 			TWL_COMMON_REGULATOR_VCXIO |
 			TWL_COMMON_REGULATOR_VUSB |
-			TWL_COMMON_REGULATOR_CLK32KG);
+			TWL_COMMON_REGULATOR_CLK32KG |
+			TWL_COMMON_REGULATOR_V1V8 |
+			TWL_COMMON_REGULATOR_V2V1);
 	omap4_pmic_init("twl6030", &sdp4430_twldata,
 			&twl6040_data, OMAP44XX_IRQ_SYS_2N);
 	omap_register_i2c_bus(2, 400, NULL, 0);
diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index c3851e8de28..3b8a53c1f2a 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -30,6 +30,7 @@
 #include "common.h"
 #include <plat/usb.h>
 
+#include "am35xx-emac.h"
 #include "mux.h"
 #include "control.h"
 
@@ -90,6 +91,7 @@ static void __init am3517_crane_init(void)
 	}
 
 	usbhs_init(&usbhs_bdata);
+	am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1);
 }
 
 MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index 909a8b91b56..d8c35a3c0fb 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -498,6 +498,10 @@ static struct twl4030_gpio_platform_data cm_t35_gpio_data = {
 	.setup          = cm_t35_twl_gpio_setup,
 };
 
+static struct twl4030_power_data cm_t35_power_data = {
+	.use_poweroff	= true,
+};
+
 static struct twl4030_platform_data cm_t35_twldata = {
 	/* platform_data for children goes here */
 	.keypad		= &cm_t35_kp_data,
@@ -505,6 +509,7 @@ static struct twl4030_platform_data cm_t35_twldata = {
 	.vmmc1		= &cm_t35_vmmc1,
 	.vsim		= &cm_t35_vsim,
 	.vio		= &cm_t35_vio,
+	.power		= &cm_t35_power_data,
 };
 
 static void __init cm_t35_init_i2c(void)
diff --git a/arch/arm/mach-omap2/board-flash.c b/arch/arm/mach-omap2/board-flash.c
index 0349fd2b68d..70a81f900bb 100644
--- a/arch/arm/mach-omap2/board-flash.c
+++ b/arch/arm/mach-omap2/board-flash.c
@@ -87,7 +87,7 @@ static struct omap_onenand_platform_data board_onenand_data = {
 	.dma_channel	= -1,   /* disable DMA in OMAP OneNAND driver */
 };
 
-static void
+void
 __init board_onenand_init(struct mtd_partition *onenand_parts,
 				u8 nr_parts, u8 cs)
 {
@@ -98,7 +98,7 @@ __init board_onenand_init(struct mtd_partition *onenand_parts,
 	gpmc_onenand_init(&board_onenand_data);
 }
 #else
-static void
+void
 __init board_onenand_init(struct mtd_partition *nor_parts, u8 nr_parts, u8 cs)
 {
 }
diff --git a/arch/arm/mach-omap2/board-flash.h b/arch/arm/mach-omap2/board-flash.h
index d25503a9841..c44b70d5202 100644
--- a/arch/arm/mach-omap2/board-flash.h
+++ b/arch/arm/mach-omap2/board-flash.h
@@ -47,3 +47,14 @@ static inline void board_nand_init(struct mtd_partition *nand_parts,
 {
 }
 #endif
+
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+		defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+extern void board_onenand_init(struct mtd_partition *nand_parts,
+					u8 nr_parts, u8 cs);
+#else
+static inline void board_onenand_init(struct mtd_partition *nand_parts,
+					u8 nr_parts, u8 cs)
+{
+}
+#endif
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 930c0d38043..16ec5c89e03 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -24,6 +24,8 @@
 #include <linux/i2c/twl.h>
 #include <linux/mmc/host.h>
 
+#include <linux/mtd/nand.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
@@ -39,6 +41,8 @@
 #include "hsmmc.h"
 #include "sdram-numonyx-m65kxxxxam.h"
 #include "common-board-devices.h"
+#include "board-flash.h"
+#include "control.h"
 
 #define IGEP2_SMSC911X_CS       5
 #define IGEP2_SMSC911X_GPIO     176
@@ -60,6 +64,10 @@
 #define IGEP3_GPIO_LED1_RED	16
 #define IGEP3_GPIO_USBH_NRESET  183
 
+#define IGEP_SYSBOOT_MASK           0x1f
+#define IGEP_SYSBOOT_NAND           0x0f
+#define IGEP_SYSBOOT_ONENAND        0x10
+
 /*
  * IGEP2 Hardware Revision Table
  *
@@ -110,8 +118,10 @@ static void __init igep2_get_revision(void)
 	gpio_free(IGEP2_GPIO_LED1_RED);
 }
 
-#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
-	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+#if defined(CONFIG_MTD_ONENAND_OMAP2) ||		\
+	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) ||	\
+	defined(CONFIG_MTD_NAND_OMAP2) ||		\
+	defined(CONFIG_MTD_NAND_OMAP2_MODULE)
 
 #define ONENAND_MAP             0x20000000
 
@@ -123,7 +133,7 @@ static void __init igep2_get_revision(void)
  * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
  */
 
-static struct mtd_partition igep_onenand_partitions[] = {
+static struct mtd_partition igep_flash_partitions[] = {
 	{
 		.name           = "X-Loader",
 		.offset         = 0,
@@ -151,50 +161,28 @@ static struct mtd_partition igep_onenand_partitions[] = {
 	},
 };
 
-static struct omap_onenand_platform_data igep_onenand_data = {
-	.parts = igep_onenand_partitions,
-	.nr_parts = ARRAY_SIZE(igep_onenand_partitions),
-	.dma_channel	= -1,	/* disable DMA in OMAP OneNAND driver */
-};
-
-static struct platform_device igep_onenand_device = {
-	.name		= "omap2-onenand",
-	.id		= -1,
-	.dev = {
-		.platform_data = &igep_onenand_data,
-	},
-};
+static inline u32 igep_get_sysboot_value(void)
+{
+	return omap_ctrl_readl(OMAP343X_CONTROL_STATUS) & IGEP_SYSBOOT_MASK;
+}
 
 static void __init igep_flash_init(void)
 {
-	u8 cs = 0;
-	u8 onenandcs = GPMC_CS_NUM + 1;
-
-	for (cs = 0; cs < GPMC_CS_NUM; cs++) {
-		u32 ret;
-		ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
-
-		/* Check if NAND/oneNAND is configured */
-		if ((ret & 0xC00) == 0x800)
-			/* NAND found */
-			pr_err("IGEP: Unsupported NAND found\n");
-		else {
-			ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
-			if ((ret & 0x3F) == (ONENAND_MAP >> 24))
-				/* ONENAND found */
-				onenandcs = cs;
-		}
-	}
-
-	if (onenandcs > GPMC_CS_NUM) {
-		pr_err("IGEP: Unable to find configuration in GPMC\n");
-		return;
+	u32 mux;
+	mux = igep_get_sysboot_value();
+
+	if (mux == IGEP_SYSBOOT_NAND) {
+		pr_info("IGEP: initializing NAND memory device\n");
+		board_nand_init(igep_flash_partitions,
+				ARRAY_SIZE(igep_flash_partitions),
+				0, NAND_BUSWIDTH_16);
+	} else if (mux == IGEP_SYSBOOT_ONENAND) {
+		pr_info("IGEP: initializing OneNAND memory device\n");
+		board_onenand_init(igep_flash_partitions,
+				   ARRAY_SIZE(igep_flash_partitions), 0);
+	} else {
+		pr_err("IGEP: Flash: unsupported sysboot sequence found\n");
 	}
-
-	igep_onenand_data.cs = onenandcs;
-
-	if (platform_device_register(&igep_onenand_device) < 0)
-		pr_err("IGEP: Unable to register OneNAND device\n");
 }
 
 #else
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 7be8d659d91..ae7d3a737ba 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -83,11 +83,13 @@ static struct {
 	int usb_pwr_level;
 	int reset_gpio;
 	int usr_button_gpio;
+	int mmc_caps;
 } beagle_config = {
 	.mmc1_gpio_wp = -EINVAL,
 	.usb_pwr_level = GPIOF_OUT_INIT_LOW,
 	.reset_gpio = 129,
 	.usr_button_gpio = 4,
+	.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 };
 
 static struct gpio omap3_beagle_rev_gpios[] __initdata = {
@@ -145,10 +147,12 @@ static void __init omap3_beagle_init_rev(void)
 		printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
 		beagle_config.usb_pwr_level = GPIOF_OUT_INIT_HIGH;
+		beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
 		break;
 	case 2:
 		printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
+		beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
 		break;
 	default:
 		printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
@@ -251,7 +255,7 @@ static void __init beagle_display_init(void)
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_wp	= -EINVAL,
 		.deferred	= true,
 	},
@@ -523,6 +527,7 @@ static void __init omap3_beagle_init(void)
 
 	if (beagle_config.mmc1_gpio_wp != -EINVAL)
 		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
+	mmc[0].caps = beagle_config.mmc_caps;
 	omap_hsmmc_init(mmc);
 
 	omap3_beagle_i2c_init();
diff --git a/arch/arm/mach-omap2/board-omap3logic.c b/arch/arm/mach-omap2/board-omap3logic.c
index 9b3c141ff51..c008bf8e1c3 100644
--- a/arch/arm/mach-omap2/board-omap3logic.c
+++ b/arch/arm/mach-omap2/board-omap3logic.c
@@ -4,8 +4,9 @@
  * Copyright (C) 2010 Li-Pro.Net
  * Stephan Linz <linz@li-pro.net>
  *
- * Copyright (C) 2010 Logic Product Development, Inc.
+ * Copyright (C) 2010-2012 Logic Product Development, Inc.
  * Peter Barada <peter.barada@logicpd.com>
+ * Ashwin BIhari <ashwin.bihari@logicpd.com>
  *
  * Modified from Beagle, EVM, and RX51
  *
@@ -45,6 +46,7 @@
 #include <plat/gpmc-smsc911x.h>
 #include <plat/gpmc.h>
 #include <plat/sdrc.h>
+#include <plat/usb.h>
 
 #define OMAP3LOGIC_SMSC911X_CS			1
 
@@ -85,6 +87,11 @@ static struct twl4030_gpio_platform_data omap3logic_gpio_data = {
 			| BIT(13) | BIT(15) | BIT(16) | BIT(17),
 };
 
+static struct twl4030_usb_data omap3logic_usb_data = {
+	.usb_mode	= T2_USB_MODE_ULPI,
+};
+
+
 static struct twl4030_platform_data omap3logic_twldata = {
 	.irq_base	= TWL4030_IRQ_BASE,
 	.irq_end	= TWL4030_IRQ_END,
@@ -92,6 +99,7 @@ static struct twl4030_platform_data omap3logic_twldata = {
 	/* platform_data for children goes here */
 	.gpio		= &omap3logic_gpio_data,
 	.vmmc1		= &omap3logic_vmmc1,
+	.usb		= &omap3logic_usb_data,
 };
 
 static int __init omap3logic_i2c_init(void)
@@ -185,6 +193,20 @@ static inline void __init board_smsc911x_init(void)
 
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
+	/* mUSB */
+	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+	OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #endif
@@ -205,6 +227,8 @@ static void __init omap3logic_init(void)
 	board_mmc_init();
 	board_smsc911x_init();
 
+	usb_musb_init(NULL);
+
 	/* Ensure SDRC pins are mux'd for self-refresh */
 	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
 	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 1b782ba5343..c1061d439fe 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -28,6 +28,7 @@
 #include <linux/mfd/twl6040.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/fixed.h>
+#include <linux/ti_wilink_st.h>
 #include <linux/wl12xx.h>
 #include <linux/platform_data/omap-abe-twl6040.h>
 
@@ -58,12 +59,21 @@
 #define HDMI_GPIO_HPD  63 /* Hotplug detect */
 
 /* wl127x BT, FM, GPS connectivity chip */
-static int wl1271_gpios[] = {46, -1, -1};
+static struct ti_st_plat_data wilink_platform_data = {
+	.nshutdown_gpio	= 46,
+	.dev_name	= "/dev/ttyO1",
+	.flow_cntrl	= 1,
+	.baud_rate	= 3000000,
+	.chip_enable	= NULL,
+	.suspend	= NULL,
+	.resume		= NULL,
+};
+
 static struct platform_device wl1271_device = {
 	.name	= "kim",
 	.id	= -1,
 	.dev	= {
-		.platform_data	= &wl1271_gpios,
+		.platform_data	= &wilink_platform_data,
 	},
 };
 
@@ -117,6 +127,11 @@ static struct platform_device panda_abe_audio = {
 	},
 };
 
+static struct platform_device panda_hdmi_audio_codec = {
+	.name	= "hdmi-audio-codec",
+	.id	= -1,
+};
+
 static struct platform_device btwilink_device = {
 	.name	= "btwilink",
 	.id	= -1,
@@ -126,6 +141,7 @@ static struct platform_device *panda_devices[] __initdata = {
 	&leds_gpio,
 	&wl1271_device,
 	&panda_abe_audio,
+	&panda_hdmi_audio_codec,
 	&btwilink_device,
 };
 
@@ -323,7 +339,9 @@ static int __init omap4_panda_i2c_init(void)
 			TWL_COMMON_REGULATOR_VANA |
 			TWL_COMMON_REGULATOR_VCXIO |
 			TWL_COMMON_REGULATOR_VUSB |
-			TWL_COMMON_REGULATOR_CLK32KG);
+			TWL_COMMON_REGULATOR_CLK32KG |
+			TWL_COMMON_REGULATOR_V1V8 |
+			TWL_COMMON_REGULATOR_V2V1);
 	omap4_pmic_init("twl6030", &omap4_panda_twldata,
 			&twl6040_data, OMAP44XX_IRQ_SYS_2N);
 	omap_register_i2c_bus(2, 400, NULL, 0);
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index d87ee061209..415a4b7e86b 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -44,6 +44,7 @@
 #include <linux/leds-lp5523.h>
 
 #include <../drivers/staging/iio/light/tsl2563.h>
+#include <linux/lis3lv02d.h>
 
 #include "mux.h"
 #include "hsmmc.h"
@@ -63,6 +64,9 @@
 #define RX51_TSC2005_RESET_GPIO         104
 #define RX51_TSC2005_IRQ_GPIO           100
 
+#define LIS302_IRQ1_GPIO 181
+#define LIS302_IRQ2_GPIO 180  /* Not yet in use */
+
 /* list all spi devices here */
 enum {
 	RX51_SPI_WL1251,
@@ -73,6 +77,77 @@ enum {
 static struct wl12xx_platform_data wl1251_pdata;
 static struct tsc2005_platform_data tsc2005_pdata;
 
+#if defined(CONFIG_SENSORS_LIS3_I2C) || defined(CONFIG_SENSORS_LIS3_I2C_MODULE)
+static int lis302_setup(void)
+{
+	int err;
+	int irq1 = LIS302_IRQ1_GPIO;
+	int irq2 = LIS302_IRQ2_GPIO;
+
+	/* gpio for interrupt pin 1 */
+	err = gpio_request(irq1, "lis3lv02dl_irq1");
+	if (err) {
+		printk(KERN_ERR "lis3lv02dl: gpio request failed\n");
+		goto out;
+	}
+
+	/* gpio for interrupt pin 2 */
+	err = gpio_request(irq2, "lis3lv02dl_irq2");
+	if (err) {
+		gpio_free(irq1);
+		printk(KERN_ERR "lis3lv02dl: gpio request failed\n");
+		goto out;
+	}
+
+	gpio_direction_input(irq1);
+	gpio_direction_input(irq2);
+
+out:
+	return err;
+}
+
+static int lis302_release(void)
+{
+	gpio_free(LIS302_IRQ1_GPIO);
+	gpio_free(LIS302_IRQ2_GPIO);
+
+	return 0;
+}
+
+static struct lis3lv02d_platform_data rx51_lis3lv02d_data = {
+	.click_flags    = LIS3_CLICK_SINGLE_X | LIS3_CLICK_SINGLE_Y |
+			  LIS3_CLICK_SINGLE_Z,
+	/* Limits are 0.5g * value */
+	.click_thresh_x = 8,
+	.click_thresh_y = 8,
+	.click_thresh_z = 10,
+	/* Click must be longer than time limit */
+	.click_time_limit = 9,
+	/* Kind of debounce filter */
+	.click_latency    = 50,
+
+	/* Limits for all axis. millig-value / 18 to get HW values */
+	.wakeup_flags = LIS3_WAKEUP_X_HI | LIS3_WAKEUP_Y_HI,
+	.wakeup_thresh = 800 / 18,
+	.wakeup_flags2 = LIS3_WAKEUP_Z_HI ,
+	.wakeup_thresh2 = 900 / 18,
+
+	.hipass_ctrl = LIS3_HIPASS1_DISABLE | LIS3_HIPASS2_DISABLE,
+
+	/* Interrupt line 2 for click detection, line 1 for thresholds */
+	.irq_cfg = LIS3_IRQ2_CLICK | LIS3_IRQ1_FF_WU_12,
+
+	.axis_x = LIS3_DEV_X,
+	.axis_y = LIS3_INV_DEV_Y,
+	.axis_z = LIS3_INV_DEV_Z,
+	.setup_resources = lis302_setup,
+	.release_resources = lis302_release,
+	.st_min_limits = {-32, 3, 3},
+	.st_max_limits = {-3, 32, 32},
+	.irq2 = OMAP_GPIO_IRQ(LIS302_IRQ2_GPIO),
+};
+#endif
+
 #if defined(CONFIG_SENSORS_TSL2563) || defined(CONFIG_SENSORS_TSL2563_MODULE)
 static struct tsl2563_platform_data rx51_tsl2563_platform_data = {
 	.cover_comp_gain = 16,
@@ -950,6 +1025,16 @@ static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_2[] = {
 	}
 };
 
+static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_3[] = {
+#if defined(CONFIG_SENSORS_LIS3_I2C) || defined(CONFIG_SENSORS_LIS3_I2C_MODULE)
+	{
+		I2C_BOARD_INFO("lis3lv02d", 0x1d),
+		.platform_data = &rx51_lis3lv02d_data,
+		.irq = OMAP_GPIO_IRQ(LIS302_IRQ1_GPIO),
+	},
+#endif
+};
+
 static int __init rx51_i2c_init(void)
 {
 	if ((system_rev >= SYSTEM_REV_S_USES_VAUX3 && system_rev < 0x100) ||
@@ -971,7 +1056,8 @@ static int __init rx51_i2c_init(void)
 	omap_pmic_init(1, 2200, "twl5030", INT_34XX_SYS_NIRQ, &rx51_twldata);
 	omap_register_i2c_bus(2, 100, rx51_peripherals_i2c_board_info_2,
 			      ARRAY_SIZE(rx51_peripherals_i2c_board_info_2));
-	omap_register_i2c_bus(3, 400, NULL, 0);
+	omap_register_i2c_bus(3, 400, rx51_peripherals_i2c_board_info_3,
+			      ARRAY_SIZE(rx51_peripherals_i2c_board_info_3));
 	return 0;
 }
 
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index e4336035c0e..17dacefaa7e 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -355,6 +355,36 @@ static void __init omap_init_dmic(void)
 static inline void omap_init_dmic(void) {}
 #endif
 
+#if defined(CONFIG_SND_OMAP_SOC_OMAP_HDMI) || \
+		defined(CONFIG_SND_OMAP_SOC_OMAP_HDMI_MODULE)
+
+static struct platform_device omap_hdmi_audio = {
+	.name	= "omap-hdmi-audio",
+	.id	= -1,
+};
+
+static void __init omap_init_hdmi_audio(void)
+{
+	struct omap_hwmod *oh;
+	struct platform_device *pdev;
+
+	oh = omap_hwmod_lookup("dss_hdmi");
+	if (!oh) {
+		printk(KERN_ERR "Could not look up dss_hdmi hw_mod\n");
+		return;
+	}
+
+	pdev = omap_device_build("omap-hdmi-audio-dai",
+		-1, oh, NULL, 0, NULL, 0, 0);
+	WARN(IS_ERR(pdev),
+	     "Can't build omap_device for omap-hdmi-audio-dai.\n");
+
+	platform_device_register(&omap_hdmi_audio);
+}
+#else
+static inline void omap_init_hdmi_audio(void) {}
+#endif
+
 #if defined(CONFIG_SPI_OMAP24XX) || defined(CONFIG_SPI_OMAP24XX_MODULE)
 
 #include <plat/mcspi.h>
@@ -704,6 +734,7 @@ static int __init omap2_init_devices(void)
 	omap_init_mcpdm();
 	omap_init_dmic();
 	omap_init_camera();
+	omap_init_hdmi_audio();
 	omap_init_mbox();
 	omap_init_mcspi();
 	omap_init_pmu();
diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c
index 7a7b89304c4..119d5a910f3 100644
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -31,6 +31,7 @@
 
 #include "twl-common.h"
 #include "pm.h"
+#include "voltage.h"
 
 static struct i2c_board_info __initdata pmic_i2c_board_info = {
 	.addr		= 0x48,
@@ -47,6 +48,18 @@ static struct i2c_board_info __initdata omap4_i2c1_board_info[] = {
 	},
 };
 
+static int twl_set_voltage(void *data, int target_uV)
+{
+	struct voltagedomain *voltdm = (struct voltagedomain *)data;
+	return voltdm_scale(voltdm, target_uV);
+}
+
+static int twl_get_voltage(void *data)
+{
+	struct voltagedomain *voltdm = (struct voltagedomain *)data;
+	return voltdm_get_voltage(voltdm);
+}
+
 void __init omap_pmic_init(int bus, u32 clkrate,
 			   const char *pmic_type, int pmic_irq,
 			   struct twl4030_platform_data *pmic_data)
@@ -153,6 +166,48 @@ static struct regulator_init_data omap3_vpll2_idata = {
 	.consumer_supplies		= omap3_vpll2_supplies,
 };
 
+static struct regulator_consumer_supply omap3_vdd1_supply[] = {
+	REGULATOR_SUPPLY("vcc", "mpu.0"),
+};
+
+static struct regulator_consumer_supply omap3_vdd2_supply[] = {
+	REGULATOR_SUPPLY("vcc", "l3_main.0"),
+};
+
+static struct regulator_init_data omap3_vdd1 = {
+	.constraints = {
+		.name			= "vdd_mpu_iva",
+		.min_uV			= 600000,
+		.max_uV			= 1450000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap3_vdd1_supply),
+	.consumer_supplies		= omap3_vdd1_supply,
+};
+
+static struct regulator_init_data omap3_vdd2 = {
+	.constraints = {
+		.name			= "vdd_core",
+		.min_uV			= 600000,
+		.max_uV			= 1450000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap3_vdd2_supply),
+	.consumer_supplies		= omap3_vdd2_supply,
+};
+
+static struct twl_regulator_driver_data omap3_vdd1_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
+static struct twl_regulator_driver_data omap3_vdd2_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
 void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
 				  u32 pdata_flags, u32 regulators_flags)
 {
@@ -160,6 +215,16 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
 		pmic_data->irq_base = TWL4030_IRQ_BASE;
 	if (!pmic_data->irq_end)
 		pmic_data->irq_end = TWL4030_IRQ_END;
+	if (!pmic_data->vdd1) {
+		omap3_vdd1.driver_data = &omap3_vdd1_drvdata;
+		omap3_vdd1_drvdata.data = voltdm_lookup("mpu_iva");
+		pmic_data->vdd1 = &omap3_vdd1;
+	}
+	if (!pmic_data->vdd2) {
+		omap3_vdd2.driver_data = &omap3_vdd2_drvdata;
+		omap3_vdd2_drvdata.data = voltdm_lookup("core");
+		pmic_data->vdd2 = &omap3_vdd2;
+	}
 
 	/* Common platform data configurations */
 	if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
@@ -201,6 +266,7 @@ static struct regulator_init_data omap4_vdac_idata = {
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
+	.supply_regulator	= "V2V1",
 };
 
 static struct regulator_init_data omap4_vaux2_idata = {
@@ -291,6 +357,7 @@ static struct regulator_init_data omap4_vcxio_idata = {
 	},
 	.num_consumer_supplies	= ARRAY_SIZE(omap4_vcxio_supply),
 	.consumer_supplies	= omap4_vcxio_supply,
+	.supply_regulator	= "V2V1",
 };
 
 static struct regulator_init_data omap4_vusb_idata = {
@@ -310,6 +377,105 @@ static struct regulator_init_data omap4_clk32kg_idata = {
 	},
 };
 
+static struct regulator_consumer_supply omap4_vdd1_supply[] = {
+	REGULATOR_SUPPLY("vcc", "mpu.0"),
+};
+
+static struct regulator_consumer_supply omap4_vdd2_supply[] = {
+	REGULATOR_SUPPLY("vcc", "iva.0"),
+};
+
+static struct regulator_consumer_supply omap4_vdd3_supply[] = {
+	REGULATOR_SUPPLY("vcc", "l3_main.0"),
+};
+
+static struct regulator_init_data omap4_vdd1 = {
+	.constraints = {
+		.name			= "vdd_mpu",
+		.min_uV			= 500000,
+		.max_uV			= 1500000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap4_vdd1_supply),
+	.consumer_supplies		= omap4_vdd1_supply,
+};
+
+static struct regulator_init_data omap4_vdd2 = {
+	.constraints = {
+		.name			= "vdd_iva",
+		.min_uV			= 500000,
+		.max_uV			= 1500000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap4_vdd2_supply),
+	.consumer_supplies		= omap4_vdd2_supply,
+};
+
+static struct regulator_init_data omap4_vdd3 = {
+	.constraints = {
+		.name			= "vdd_core",
+		.min_uV			= 500000,
+		.max_uV			= 1500000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap4_vdd3_supply),
+	.consumer_supplies		= omap4_vdd3_supply,
+};
+
+
+static struct twl_regulator_driver_data omap4_vdd1_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
+static struct twl_regulator_driver_data omap4_vdd2_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
+static struct twl_regulator_driver_data omap4_vdd3_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
+static struct regulator_consumer_supply omap4_v1v8_supply[] = {
+	REGULATOR_SUPPLY("vio", "1-004b"),
+};
+
+static struct regulator_init_data omap4_v1v8_idata = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+		.always_on		= true,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(omap4_v1v8_supply),
+	.consumer_supplies	= omap4_v1v8_supply,
+};
+
+static struct regulator_consumer_supply omap4_v2v1_supply[] = {
+	REGULATOR_SUPPLY("v2v1", "1-004b"),
+};
+
+static struct regulator_init_data omap4_v2v1_idata = {
+	.constraints = {
+		.min_uV			= 2100000,
+		.max_uV			= 2100000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(omap4_v2v1_supply),
+	.consumer_supplies	= omap4_v2v1_supply,
+};
+
 void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
 				  u32 pdata_flags, u32 regulators_flags)
 {
@@ -318,6 +484,24 @@ void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
 	if (!pmic_data->irq_end)
 		pmic_data->irq_end = TWL6030_IRQ_END;
 
+	if (!pmic_data->vdd1) {
+		omap4_vdd1.driver_data = &omap4_vdd1_drvdata;
+		omap4_vdd1_drvdata.data = voltdm_lookup("mpu");
+		pmic_data->vdd1 = &omap4_vdd1;
+	}
+
+	if (!pmic_data->vdd2) {
+		omap4_vdd2.driver_data = &omap4_vdd2_drvdata;
+		omap4_vdd2_drvdata.data = voltdm_lookup("iva");
+		pmic_data->vdd2 = &omap4_vdd2;
+	}
+
+	if (!pmic_data->vdd3) {
+		omap4_vdd3.driver_data = &omap4_vdd3_drvdata;
+		omap4_vdd3_drvdata.data = voltdm_lookup("core");
+		pmic_data->vdd3 = &omap4_vdd3;
+	}
+
 	/* Common platform data configurations */
 	if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
 		pmic_data->usb = &omap4_usb_pdata;
@@ -350,5 +534,11 @@ void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
 	if (regulators_flags & TWL_COMMON_REGULATOR_CLK32KG &&
 	    !pmic_data->clk32kg)
 		pmic_data->clk32kg = &omap4_clk32kg_idata;
+
+	if (regulators_flags & TWL_COMMON_REGULATOR_V1V8 && !pmic_data->v1v8)
+		pmic_data->v1v8 = &omap4_v1v8_idata;
+
+	if (regulators_flags & TWL_COMMON_REGULATOR_V2V1 && !pmic_data->v2v1)
+		pmic_data->v2v1 = &omap4_v2v1_idata;
 }
 #endif /* CONFIG_ARCH_OMAP4 */
diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h
index 09627483a57..8fe71cfd002 100644
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -22,6 +22,8 @@
 #define TWL_COMMON_REGULATOR_VCXIO	(1 << 8)
 #define TWL_COMMON_REGULATOR_VUSB	(1 << 9)
 #define TWL_COMMON_REGULATOR_CLK32KG	(1 << 10)
+#define TWL_COMMON_REGULATOR_V1V8	(1 << 11)
+#define TWL_COMMON_REGULATOR_V2V1	(1 << 12)
 
 /* TWL4030 LDO regulators */
 #define TWL_COMMON_REGULATOR_VPLL1	(1 << 4)
diff --git a/arch/arm/mach-omap2/vc3xxx_data.c b/arch/arm/mach-omap2/vc3xxx_data.c
index a5ec7f8f2ea..5d8eaf31569 100644
--- a/arch/arm/mach-omap2/vc3xxx_data.c
+++ b/arch/arm/mach-omap2/vc3xxx_data.c
@@ -46,6 +46,7 @@ static struct omap_vc_common omap3_vc_common = {
 };
 
 struct omap_vc_channel omap3_vc_mpu = {
+	.flags = OMAP_VC_CHANNEL_DEFAULT,
 	.common = &omap3_vc_common,
 	.smps_sa_reg	 = OMAP3_PRM_VC_SMPS_SA_OFFSET,
 	.smps_volra_reg	 = OMAP3_PRM_VC_SMPS_VOL_RA_OFFSET,
diff --git a/arch/arm/mach-omap2/voltage.c b/arch/arm/mach-omap2/voltage.c
index 8a36342e60d..4dc60e83e00 100644
--- a/arch/arm/mach-omap2/voltage.c
+++ b/arch/arm/mach-omap2/voltage.c
@@ -73,7 +73,8 @@ unsigned long voltdm_get_voltage(struct voltagedomain *voltdm)
 int voltdm_scale(struct voltagedomain *voltdm,
 		 unsigned long target_volt)
 {
-	int ret;
+	int ret, i;
+	unsigned long volt = 0;
 
 	if (!voltdm || IS_ERR(voltdm)) {
 		pr_warning("%s: VDD specified does not exist!\n", __func__);
@@ -86,9 +87,23 @@ int voltdm_scale(struct voltagedomain *voltdm,
 		return -ENODATA;
 	}
 
-	ret = voltdm->scale(voltdm, target_volt);
+	/* Adjust voltage to the exact voltage from the OPP table */
+	for (i = 0; voltdm->volt_data[i].volt_nominal != 0; i++) {
+		if (voltdm->volt_data[i].volt_nominal >= target_volt) {
+			volt = voltdm->volt_data[i].volt_nominal;
+			break;
+		}
+	}
+
+	if (!volt) {
+		pr_warning("%s: not scaling. OPP voltage for %lu, not found.\n",
+			   __func__, target_volt);
+		return -EINVAL;
+	}
+
+	ret = voltdm->scale(voltdm, volt);
 	if (!ret)
-		voltdm->nominal_volt = target_volt;
+		voltdm->nominal_volt = volt;
 
 	return ret;
 }