Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next

Pull part one of ARM SoC updates from Olof Johansson:
 "A quite large set of SoC updates this cycle.  In no particular order:

   - Multi-cluster power management for Samsung Exynos, adding support
     for big.LITTLE CPU switching on EXYNOS5

   - SMP support for Marvell Armada 375 and 38x

   - SMP rework on Allwinner A31

   - Xilinx Zynq support for SOC_BUS, big endian

   - Marvell orion5x platform cleanup, modernizing the implementation
     and moving to DT.

   - _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
     that their platform can be enabled in the same kernel binary as
     most of the other v7 platforms in the tree.  \o/

     The work isn't quite complete, there's some driver fixes still
     needed, but the basics now work.

  New SoC support added:

   - Freescale i.MX6SX

   - LSI Axxia AXM55xx SoCs

   - Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800

   - STi STIH407

  plus a large set of various smaller updates for different platforms.
  I'm probably missing some important one here"

* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
  ARM: exynos: don't run exynos4 l2x0 setup on other platforms
  ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
  ARM: EXYNOS: mcpm rename the power_down_finish
  ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
  ARM: EXYNOS: Enable multi-platform build support
  ARM: EXYNOS: Consolidate Kconfig entries
  ARM: EXYNOS: Add support for EXYNOS5410 SoC
  ARM: EXYNOS: Support secondary CPU boot of Exynos3250
  ARM: EXYNOS: Add Exynos3250 SoC ID
  ARM: EXYNOS: Add 5800 SoC support
  ARM: EXYNOS: initial board support for exynos5260 SoC
  clk: exynos5410: register clocks using common clock framework
  ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
  ARM: sunxi: allow building without reset controller
  Documentation: devicetree: arm: sort enable-method entries
  ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
  clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
  ARM: dts: axxia: Add reset controller
  power: reset: Add Axxia system reset driver
  ARM: axxia: Adding defconfig for AXM55xx
  ...

11 files changed, 380 insertions, 846 deletions

diff --git a/arch/arm/mach-orion5x/Kconfig b/arch/arm/mach-orion5x/Kconfig
index 14f2cae4109..2412efb6cdd 100644
--- a/arch/arm/mach-orion5x/Kconfig
+++ b/arch/arm/mach-orion5x/Kconfig
@@ -5,6 +5,11 @@ menu "Orion Implementations"
 config ARCH_ORION5X_DT
 	bool "Marvell Orion5x Flattened Device Tree"
 	select USE_OF
+	select ORION_CLK
+	select ORION_IRQCHIP
+	select ORION_TIMER
+	select PINCTRL
+	select PINCTRL_ORION
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion5x using flattened device tree.
@@ -23,6 +28,14 @@ config MACH_RD88F5182
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion-NAS (88F5182) RD2
 
+config MACH_RD88F5182_DT
+	bool "Marvell Orion-NAS Reference Design (Flattened Device Tree)"
+	select ARCH_ORION5X_DT
+	select I2C_BOARDINFO
+	help
+	  Say 'Y' here if you want your kernel to support the Marvell
+	  Orion-NAS (88F5182) RD2, Flattened Device Tree.
+
 config MACH_KUROBOX_PRO
 	bool "KuroBox Pro"
 	select I2C_BOARDINFO
@@ -102,28 +115,13 @@ config MACH_MV2120
 	  Say 'Y' here if you want your kernel to support the
 	  HP Media Vault mv2120 or mv5100.
 
-config MACH_EDMINI_V2_DT
-	bool "LaCie Ethernet Disk mini V2 (Flattened Device Tree)"
-	select I2C_BOARDINFO
+config MACH_D2NET_DT
+	bool "LaCie d2 Network / Big Disk Network (Flattened Device Tree)"
 	select ARCH_ORION5X_DT
 	help
 	  Say 'Y' here if you want your kernel to support the
-	  LaCie Ethernet Disk mini V2 (Flattened Device Tree).
-
-config MACH_D2NET
-	bool "LaCie d2 Network"
-	select I2C_BOARDINFO
-	help
-	  Say 'Y' here if you want your kernel to support the
 	  LaCie d2 Network NAS.
 
-config MACH_BIGDISK
-	bool "LaCie Big Disk Network"
-	select I2C_BOARDINFO
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  LaCie Big Disk Network NAS.
-
 config MACH_NET2BIG
 	bool "LaCie 2Big Network"
 	select I2C_BOARDINFO
@@ -131,8 +129,9 @@ config MACH_NET2BIG
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie 2Big Network NAS.
 
-config MACH_MSS2
-	bool "Maxtor Shared Storage II"
+config MACH_MSS2_DT
+	bool "Maxtor Shared Storage II (Flattened Device Tree)"
+	select ARCH_ORION5X_DT
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Maxtor Shared Storage II platform.
diff --git a/arch/arm/mach-orion5x/Makefile b/arch/arm/mach-orion5x/Makefile
index 45da805fb23..a40b5c9a58c 100644
--- a/arch/arm/mach-orion5x/Makefile
+++ b/arch/arm/mach-orion5x/Makefile
@@ -12,10 +12,7 @@ obj-$(CONFIG_MACH_TS409)	+= ts409-setup.o tsx09-common.o
 obj-$(CONFIG_MACH_WRT350N_V2)	+= wrt350n-v2-setup.o
 obj-$(CONFIG_MACH_TS78XX)	+= ts78xx-setup.o
 obj-$(CONFIG_MACH_MV2120)	+= mv2120-setup.o
-obj-$(CONFIG_MACH_D2NET)	+= d2net-setup.o
-obj-$(CONFIG_MACH_BIGDISK)	+= d2net-setup.o
 obj-$(CONFIG_MACH_NET2BIG)	+= net2big-setup.o
-obj-$(CONFIG_MACH_MSS2)		+= mss2-setup.o
 obj-$(CONFIG_MACH_WNR854T)	+= wnr854t-setup.o
 obj-$(CONFIG_MACH_RD88F5181L_GE)	+= rd88f5181l-ge-setup.o
 obj-$(CONFIG_MACH_RD88F5181L_FXO)	+= rd88f5181l-fxo-setup.o
@@ -23,4 +20,6 @@ obj-$(CONFIG_MACH_RD88F6183AP_GE)	+= rd88f6183ap-ge-setup.o
 obj-$(CONFIG_MACH_LINKSTATION_LSCHL)	+= ls-chl-setup.o
 
 obj-$(CONFIG_ARCH_ORION5X_DT)		+= board-dt.o
-obj-$(CONFIG_MACH_EDMINI_V2_DT)	+= edmini_v2-setup.o
+obj-$(CONFIG_MACH_D2NET_DT)	+= board-d2net.o
+obj-$(CONFIG_MACH_MSS2_DT)	+= board-mss2.o
+obj-$(CONFIG_MACH_RD88F5182_DT)	+= board-rd88f5182.o
diff --git a/arch/arm/mach-orion5x/board-d2net.c b/arch/arm/mach-orion5x/board-d2net.c
new file mode 100644
index 00000000000..8a728412415
--- /dev/null
+++ b/arch/arm/mach-orion5x/board-d2net.c
@@ -0,0 +1,109 @@
+/*
+ * arch/arm/mach-orion5x/board-d2net.c
+ *
+ * LaCie d2Network and Big Disk Network NAS setup
+ *
+ * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include <plat/orion-gpio.h>
+#include "common.h"
+
+/*****************************************************************************
+ * LaCie d2 Network Info
+ ****************************************************************************/
+
+/*****************************************************************************
+ * GPIO LED's
+ ****************************************************************************/
+
+/*
+ * The blue front LED is wired to the CPLD and can blink in relation with the
+ * SATA activity.
+ *
+ * The following array detail the different LED registers and the combination
+ * of their possible values:
+ *
+ * led_off   | blink_ctrl | SATA active | LED state
+ *           |            |             |
+ *    1      |     x      |      x      |  off
+ *    0      |     0      |      0      |  off
+ *    0      |     1      |      0      |  blink (rate 300ms)
+ *    0      |     x      |      1      |  on
+ *
+ * Notes: The blue and the red front LED's can't be on at the same time.
+ *        Red LED have priority.
+ */
+
+#define D2NET_GPIO_RED_LED		6
+#define D2NET_GPIO_BLUE_LED_BLINK_CTRL	16
+#define D2NET_GPIO_BLUE_LED_OFF		23
+
+static struct gpio_led d2net_leds[] = {
+	{
+		.name = "d2net:blue:sata",
+		.default_trigger = "default-on",
+		.gpio = D2NET_GPIO_BLUE_LED_OFF,
+		.active_low = 1,
+	},
+	{
+		.name = "d2net:red:fail",
+		.gpio = D2NET_GPIO_RED_LED,
+	},
+};
+
+static struct gpio_led_platform_data d2net_led_data = {
+	.num_leds = ARRAY_SIZE(d2net_leds),
+	.leds = d2net_leds,
+};
+
+static struct platform_device d2net_gpio_leds = {
+	.name           = "leds-gpio",
+	.id             = -1,
+	.dev            = {
+		.platform_data  = &d2net_led_data,
+	},
+};
+
+static void __init d2net_gpio_leds_init(void)
+{
+	int err;
+
+	/* Configure register blink_ctrl to allow SATA activity LED blinking. */
+	err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
+	}
+	if (err)
+		pr_err("d2net: failed to configure blue LED blink GPIO\n");
+
+	platform_device_register(&d2net_gpio_leds);
+}
+
+/*****************************************************************************
+ * General Setup
+ ****************************************************************************/
+
+void __init d2net_init(void)
+{
+	d2net_gpio_leds_init();
+
+	pr_notice("d2net: Flash write are not yet supported.\n");
+}
diff --git a/arch/arm/mach-orion5x/board-dt.c b/arch/arm/mach-orion5x/board-dt.c
index c134a826070..35d418faf8f 100644
--- a/arch/arm/mach-orion5x/board-dt.c
+++ b/arch/arm/mach-orion5x/board-dt.c
@@ -15,10 +15,16 @@
 #include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/cpu.h>
+#include <linux/mbus.h>
+#include <linux/clk-provider.h>
+#include <linux/clocksource.h>
 #include <asm/system_misc.h>
 #include <asm/mach/arch.h>
+#include <asm/mach/map.h>
 #include <mach/orion5x.h>
+#include <mach/bridge-regs.h>
 #include <plat/irq.h>
+#include <plat/time.h>
 #include "common.h"
 
 static struct of_dev_auxdata orion5x_auxdata_lookup[] __initdata = {
@@ -39,14 +45,13 @@ static void __init orion5x_dt_init(void)
 	orion5x_id(&dev, &rev, &dev_name);
 	printk(KERN_INFO "Orion ID: %s. TCLK=%d.\n", dev_name, orion5x_tclk);
 
+	BUG_ON(mvebu_mbus_dt_init());
+
 	/*
 	 * Setup Orion address map
 	 */
 	orion5x_setup_wins();
 
-	/* Setup root of clk tree */
-	clk_init();
-
 	/*
 	 * Don't issue "Wait for Interrupt" instruction if we are
 	 * running on D0 5281 silicon.
@@ -56,8 +61,8 @@ static void __init orion5x_dt_init(void)
 		cpu_idle_poll_ctrl(true);
 	}
 
-	if (of_machine_is_compatible("lacie,ethernet-disk-mini-v2"))
-		edmini_v2_init();
+	if (of_machine_is_compatible("maxtor,shared-storage-2"))
+		mss2_init();
 
 	of_platform_populate(NULL, of_default_bus_match_table,
 			     orion5x_auxdata_lookup, NULL);
@@ -71,9 +76,6 @@ static const char *orion5x_dt_compat[] = {
 DT_MACHINE_START(ORION5X_DT, "Marvell Orion5x (Flattened Device Tree)")
 	/* Maintainer: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> */
 	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion_dt_init_irq,
-	.init_time	= orion5x_timer_init,
 	.init_machine	= orion5x_dt_init,
 	.restart	= orion5x_restart,
 	.dt_compat	= orion5x_dt_compat,
diff --git a/arch/arm/mach-orion5x/board-mss2.c b/arch/arm/mach-orion5x/board-mss2.c
new file mode 100644
index 00000000000..66f9c3ba86c
--- /dev/null
+++ b/arch/arm/mach-orion5x/board-mss2.c
@@ -0,0 +1,90 @@
+/*
+ * Maxtor Shared Storage II Board Setup
+ *
+ * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include <mach/bridge-regs.h>
+#include "common.h"
+
+/*****************************************************************************
+ * Maxtor Shared Storage II Info
+ ****************************************************************************/
+
+/****************************************************************************
+ * PCI setup
+ ****************************************************************************/
+static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int irq;
+
+	/*
+	 * Check for devices with hard-wired IRQs.
+	 */
+	irq = orion5x_pci_map_irq(dev, slot, pin);
+	if (irq != -1)
+		return irq;
+
+	return -1;
+}
+
+static struct hw_pci mss2_pci __initdata = {
+	.nr_controllers = 2,
+	.setup		= orion5x_pci_sys_setup,
+	.scan		= orion5x_pci_sys_scan_bus,
+	.map_irq	= mss2_pci_map_irq,
+};
+
+static int __init mss2_pci_init(void)
+{
+	if (machine_is_mss2())
+		pci_common_init(&mss2_pci);
+
+	return 0;
+}
+subsys_initcall(mss2_pci_init);
+
+/*****************************************************************************
+ * MSS2 power off method
+ ****************************************************************************/
+/*
+ * On the Maxtor Shared Storage II, the shutdown process is the following :
+ * - Userland modifies U-boot env to tell U-boot to go idle at next boot
+ * - The board reboots
+ * - U-boot starts and go into an idle mode until the user press "power"
+ */
+static void mss2_power_off(void)
+{
+	u32 reg;
+
+	/*
+	 * Enable and issue soft reset
+	 */
+	reg = readl(RSTOUTn_MASK);
+	reg |= 1 << 2;
+	writel(reg, RSTOUTn_MASK);
+
+	reg = readl(CPU_SOFT_RESET);
+	reg |= 1;
+	writel(reg, CPU_SOFT_RESET);
+}
+
+void __init mss2_init(void)
+{
+	/* register mss2 specific power-off method */
+	pm_power_off = mss2_power_off;
+}
diff --git a/arch/arm/mach-orion5x/board-rd88f5182.c b/arch/arm/mach-orion5x/board-rd88f5182.c
new file mode 100644
index 00000000000..270824b0e50
--- /dev/null
+++ b/arch/arm/mach-orion5x/board-rd88f5182.c
@@ -0,0 +1,116 @@
+/*
+ * arch/arm/mach-orion5x/rd88f5182-setup.c
+ *
+ * Marvell Orion-NAS Reference Design Setup
+ *
+ * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include "common.h"
+
+/*****************************************************************************
+ * RD-88F5182 Info
+ ****************************************************************************/
+
+/*
+ * PCI
+ */
+
+#define RD88F5182_PCI_SLOT0_OFFS	7
+#define RD88F5182_PCI_SLOT0_IRQ_A_PIN	7
+#define RD88F5182_PCI_SLOT0_IRQ_B_PIN	6
+
+/*****************************************************************************
+ * PCI
+ ****************************************************************************/
+
+static void __init rd88f5182_pci_preinit(void)
+{
+	int pin;
+
+	/*
+	 * Configure PCI GPIO IRQ pins
+	 */
+	pin = RD88F5182_PCI_SLOT0_IRQ_A_PIN;
+	if (gpio_request(pin, "PCI IntA") == 0) {
+		if (gpio_direction_input(pin) == 0) {
+			irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
+		} else {
+			printk(KERN_ERR "rd88f5182_pci_preinit failed to "
+					"set_irq_type pin %d\n", pin);
+			gpio_free(pin);
+		}
+	} else {
+		printk(KERN_ERR "rd88f5182_pci_preinit failed to request gpio %d\n", pin);
+	}
+
+	pin = RD88F5182_PCI_SLOT0_IRQ_B_PIN;
+	if (gpio_request(pin, "PCI IntB") == 0) {
+		if (gpio_direction_input(pin) == 0) {
+			irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
+		} else {
+			printk(KERN_ERR "rd88f5182_pci_preinit failed to "
+					"set_irq_type pin %d\n", pin);
+			gpio_free(pin);
+		}
+	} else {
+		printk(KERN_ERR "rd88f5182_pci_preinit failed to gpio_request %d\n", pin);
+	}
+}
+
+static int __init rd88f5182_pci_map_irq(const struct pci_dev *dev, u8 slot,
+	u8 pin)
+{
+	int irq;
+
+	/*
+	 * Check for devices with hard-wired IRQs.
+	 */
+	irq = orion5x_pci_map_irq(dev, slot, pin);
+	if (irq != -1)
+		return irq;
+
+	/*
+	 * PCI IRQs are connected via GPIOs
+	 */
+	switch (slot - RD88F5182_PCI_SLOT0_OFFS) {
+	case 0:
+		if (pin == 1)
+			return gpio_to_irq(RD88F5182_PCI_SLOT0_IRQ_A_PIN);
+		else
+			return gpio_to_irq(RD88F5182_PCI_SLOT0_IRQ_B_PIN);
+	default:
+		return -1;
+	}
+}
+
+static struct hw_pci rd88f5182_pci __initdata = {
+	.nr_controllers	= 2,
+	.preinit	= rd88f5182_pci_preinit,
+	.setup		= orion5x_pci_sys_setup,
+	.scan		= orion5x_pci_sys_scan_bus,
+	.map_irq	= rd88f5182_pci_map_irq,
+};
+
+static int __init rd88f5182_pci_init(void)
+{
+	if (of_machine_is_compatible("marvell,rd-88f5182-nas"))
+		pci_common_init(&rd88f5182_pci);
+
+	return 0;
+}
+
+subsys_initcall(rd88f5182_pci_init);
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index 7548db2bfb8..26d6f34b602 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -64,17 +64,16 @@ int orion5x_pci_sys_setup(int nr, struct pci_sys_data *sys);
 struct pci_bus *orion5x_pci_sys_scan_bus(int nr, struct pci_sys_data *sys);
 int orion5x_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
 
-/* board init functions for boards not fully converted to fdt */
-#ifdef CONFIG_MACH_EDMINI_V2_DT
-void edmini_v2_init(void);
-#else
-static inline void edmini_v2_init(void) {};
-#endif
-
 struct meminfo;
 struct tag;
 extern void __init tag_fixup_mem32(struct tag *, char **, struct meminfo *);
 
+#ifdef CONFIG_MACH_MSS2_DT
+extern void mss2_init(void);
+#else
+static inline void mss2_init(void) {}
+#endif
+
 /*****************************************************************************
  * Helpers to access Orion registers
  ****************************************************************************/
diff --git a/arch/arm/mach-orion5x/d2net-setup.c b/arch/arm/mach-orion5x/d2net-setup.c
deleted file mode 100644
index 8f68b745c1d..00000000000
--- a/arch/arm/mach-orion5x/d2net-setup.c
+++ /dev/null
@@ -1,365 +0,0 @@
-/*
- * arch/arm/mach-orion5x/d2net-setup.c
- *
- * LaCie d2Network and Big Disk Network NAS setup
- *
- * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include <plat/orion-gpio.h>
-#include "common.h"
-#include "mpp.h"
-
-/*****************************************************************************
- * LaCie d2 Network Info
- ****************************************************************************/
-
-/*
- * 512KB NOR flash Device bus boot chip select
- */
-
-#define D2NET_NOR_BOOT_BASE		0xfff80000
-#define D2NET_NOR_BOOT_SIZE		SZ_512K
-
-/*****************************************************************************
- * 512KB NOR Flash on Boot Device
- ****************************************************************************/
-
-/*
- * TODO: Check write support on flash MX29LV400CBTC-70G
- */
-
-static struct mtd_partition d2net_partitions[] = {
-	{
-		.name		= "Full512kb",
-		.size		= MTDPART_SIZ_FULL,
-		.offset		= 0,
-		.mask_flags	= MTD_WRITEABLE,
-	},
-};
-
-static struct physmap_flash_data d2net_nor_flash_data = {
-	.width		= 1,
-	.parts		= d2net_partitions,
-	.nr_parts	= ARRAY_SIZE(d2net_partitions),
-};
-
-static struct resource d2net_nor_flash_resource = {
-	.flags			= IORESOURCE_MEM,
-	.start			= D2NET_NOR_BOOT_BASE,
-	.end			= D2NET_NOR_BOOT_BASE
-					+ D2NET_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device d2net_nor_flash = {
-	.name			= "physmap-flash",
-	.id			= 0,
-	.dev		= {
-		.platform_data	= &d2net_nor_flash_data,
-	},
-	.num_resources		= 1,
-	.resource		= &d2net_nor_flash_resource,
-};
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data d2net_eth_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * I2C devices
- ****************************************************************************/
-
-/*
- * i2c addr | chip         | description
- * 0x32     | Ricoh 5C372b | RTC
- * 0x3e     | GMT G762     | PWM fan controller
- * 0x50     | HT24LC08     | eeprom (1kB)
- *
- * TODO: Add G762 support to the g760a driver.
- */
-static struct i2c_board_info __initdata d2net_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("rs5c372b", 0x32),
-	}, {
-		I2C_BOARD_INFO("24c08", 0x50),
-	},
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data d2net_sata_data = {
-	.n_ports	= 2,
-};
-
-#define D2NET_GPIO_SATA0_POWER	3
-#define D2NET_GPIO_SATA1_POWER	12
-
-static void __init d2net_sata_power_init(void)
-{
-	int err;
-
-	err = gpio_request(D2NET_GPIO_SATA0_POWER, "SATA0 power");
-	if (err == 0) {
-		err = gpio_direction_output(D2NET_GPIO_SATA0_POWER, 1);
-		if (err)
-			gpio_free(D2NET_GPIO_SATA0_POWER);
-	}
-	if (err)
-		pr_err("d2net: failed to configure SATA0 power GPIO\n");
-
-	err = gpio_request(D2NET_GPIO_SATA1_POWER, "SATA1 power");
-	if (err == 0) {
-		err = gpio_direction_output(D2NET_GPIO_SATA1_POWER, 1);
-		if (err)
-			gpio_free(D2NET_GPIO_SATA1_POWER);
-	}
-	if (err)
-		pr_err("d2net: failed to configure SATA1 power GPIO\n");
-}
-
-/*****************************************************************************
- * GPIO LED's
- ****************************************************************************/
-
-/*
- * The blue front LED is wired to the CPLD and can blink in relation with the
- * SATA activity.
- *
- * The following array detail the different LED registers and the combination
- * of their possible values:
- *
- * led_off   | blink_ctrl | SATA active | LED state
- *           |            |             |
- *    1      |     x      |      x      |  off
- *    0      |     0      |      0      |  off
- *    0      |     1      |      0      |  blink (rate 300ms)
- *    0      |     x      |      1      |  on
- *
- * Notes: The blue and the red front LED's can't be on at the same time.
- *        Red LED have priority.
- */
-
-#define D2NET_GPIO_RED_LED		6
-#define D2NET_GPIO_BLUE_LED_BLINK_CTRL	16
-#define D2NET_GPIO_BLUE_LED_OFF		23
-
-static struct gpio_led d2net_leds[] = {
-	{
-		.name = "d2net:blue:sata",
-		.default_trigger = "default-on",
-		.gpio = D2NET_GPIO_BLUE_LED_OFF,
-		.active_low = 1,
-	},
-	{
-		.name = "d2net:red:fail",
-		.gpio = D2NET_GPIO_RED_LED,
-	},
-};
-
-static struct gpio_led_platform_data d2net_led_data = {
-	.num_leds = ARRAY_SIZE(d2net_leds),
-	.leds = d2net_leds,
-};
-
-static struct platform_device d2net_gpio_leds = {
-	.name           = "leds-gpio",
-	.id             = -1,
-	.dev            = {
-		.platform_data  = &d2net_led_data,
-	},
-};
-
-static void __init d2net_gpio_leds_init(void)
-{
-	int err;
-
-	/* Configure GPIO over MPP max number. */
-	orion_gpio_set_valid(D2NET_GPIO_BLUE_LED_OFF, 1);
-
-	/* Configure register blink_ctrl to allow SATA activity LED blinking. */
-	err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
-	if (err == 0) {
-		err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
-		if (err)
-			gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
-	}
-	if (err)
-		pr_err("d2net: failed to configure blue LED blink GPIO\n");
-
-	platform_device_register(&d2net_gpio_leds);
-}
-
-/****************************************************************************
- * GPIO keys
- ****************************************************************************/
-
-#define D2NET_GPIO_PUSH_BUTTON		18
-#define D2NET_GPIO_POWER_SWITCH_ON	8
-#define D2NET_GPIO_POWER_SWITCH_OFF	9
-
-#define D2NET_SWITCH_POWER_ON		0x1
-#define D2NET_SWITCH_POWER_OFF		0x2
-
-static struct gpio_keys_button d2net_buttons[] = {
-	{
-		.type		= EV_SW,
-		.code		= D2NET_SWITCH_POWER_OFF,
-		.gpio		= D2NET_GPIO_POWER_SWITCH_OFF,
-		.desc		= "Power rocker switch (auto|off)",
-		.active_low	= 0,
-	},
-	{
-		.type		= EV_SW,
-		.code		= D2NET_SWITCH_POWER_ON,
-		.gpio		= D2NET_GPIO_POWER_SWITCH_ON,
-		.desc		= "Power rocker switch (on|auto)",
-		.active_low	= 0,
-	},
-	{
-		.type		= EV_KEY,
-		.code		= KEY_POWER,
-		.gpio		= D2NET_GPIO_PUSH_BUTTON,
-		.desc		= "Front Push Button",
-		.active_low	= 0,
-	},
-};
-
-static struct gpio_keys_platform_data d2net_button_data = {
-	.buttons	= d2net_buttons,
-	.nbuttons	= ARRAY_SIZE(d2net_buttons),
-};
-
-static struct platform_device d2net_gpio_buttons = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &d2net_button_data,
-	},
-};
-
-/*****************************************************************************
- * General Setup
- ****************************************************************************/
-
-static unsigned int d2net_mpp_modes[] __initdata = {
-	MPP0_GPIO,	/* Board ID (bit 0) */
-	MPP1_GPIO,	/* Board ID (bit 1) */
-	MPP2_GPIO,	/* Board ID (bit 2) */
-	MPP3_GPIO,	/* SATA 0 power */
-	MPP4_UNUSED,
-	MPP5_GPIO,	/* Fan fail detection */
-	MPP6_GPIO,	/* Red front LED */
-	MPP7_UNUSED,
-	MPP8_GPIO,	/* Rear power switch (on|auto) */
-	MPP9_GPIO,	/* Rear power switch (auto|off) */
-	MPP10_UNUSED,
-	MPP11_UNUSED,
-	MPP12_GPIO,	/* SATA 1 power */
-	MPP13_UNUSED,
-	MPP14_SATA_LED,	/* SATA 0 active */
-	MPP15_SATA_LED,	/* SATA 1 active */
-	MPP16_GPIO,	/* Blue front LED blink control */
-	MPP17_UNUSED,
-	MPP18_GPIO,	/* Front button (0 = Released, 1 = Pushed ) */
-	MPP19_UNUSED,
-	0,
-	/* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
-	/* 23: Blue front LED off */
-	/* 24: Inhibit board power off (0 = Disabled, 1 = Enabled) */
-};
-
-#define D2NET_GPIO_INHIBIT_POWER_OFF    24
-
-static void __init d2net_init(void)
-{
-	/*
-	 * Setup basic Orion functions. Need to be called early.
-	 */
-	orion5x_init();
-
-	orion5x_mpp_conf(d2net_mpp_modes);
-
-	/*
-	 * Configure peripherals.
-	 */
-	orion5x_ehci0_init();
-	orion5x_eth_init(&d2net_eth_data);
-	orion5x_i2c_init();
-	orion5x_uart0_init();
-
-	d2net_sata_power_init();
-	orion5x_sata_init(&d2net_sata_data);
-
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-				    D2NET_NOR_BOOT_BASE,
-				    D2NET_NOR_BOOT_SIZE);
-	platform_device_register(&d2net_nor_flash);
-
-	platform_device_register(&d2net_gpio_buttons);
-
-	d2net_gpio_leds_init();
-
-	pr_notice("d2net: Flash write are not yet supported.\n");
-
-	i2c_register_board_info(0, d2net_i2c_devices,
-				ARRAY_SIZE(d2net_i2c_devices));
-
-	orion_gpio_set_valid(D2NET_GPIO_INHIBIT_POWER_OFF, 1);
-}
-
-/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
-
-#ifdef CONFIG_MACH_D2NET
-MACHINE_START(D2NET, "LaCie d2 Network")
-	.atag_offset	= 0x100,
-	.init_machine	= d2net_init,
-	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion5x_init_irq,
-	.init_time	= orion5x_timer_init,
-	.fixup		= tag_fixup_mem32,
-	.restart	= orion5x_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_BIGDISK
-MACHINE_START(BIGDISK, "LaCie Big Disk Network")
-	.atag_offset	= 0x100,
-	.init_machine	= d2net_init,
-	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion5x_init_irq,
-	.init_time	= orion5x_timer_init,
-	.fixup		= tag_fixup_mem32,
-	.restart	= orion5x_restart,
-MACHINE_END
-#endif
-
diff --git a/arch/arm/mach-orion5x/edmini_v2-setup.c b/arch/arm/mach-orion5x/edmini_v2-setup.c
deleted file mode 100644
index f66c1b2ee8c..00000000000
--- a/arch/arm/mach-orion5x/edmini_v2-setup.c
+++ /dev/null
@@ -1,169 +0,0 @@
-/*
- * arch/arm/mach-orion5x/edmini_v2-setup.c
- *
- * LaCie Ethernet Disk mini V2 Setup
- *
- * Copyright (C) 2008 Christopher Moore <moore@free.fr>
- * Copyright (C) 2008 Albert Aribaud <albert.aribaud@free.fr>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-/*
- * TODO: add Orion USB device port init when kernel.org support is added.
- * TODO: add flash write support: see below.
- * TODO: add power-off support.
- * TODO: add I2C EEPROM support.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mbus.h>
-#include <linux/mtd/physmap.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include "common.h"
-#include "mpp.h"
-
-/*****************************************************************************
- * EDMINI_V2 Info
- ****************************************************************************/
-
-/*
- * 512KB NOR flash Device bus boot chip select
- */
-
-#define EDMINI_V2_NOR_BOOT_BASE		0xfff80000
-#define EDMINI_V2_NOR_BOOT_SIZE		SZ_512K
-
-/*****************************************************************************
- * 512KB NOR Flash on BOOT Device
- ****************************************************************************/
-
-/*
- * Currently the MTD code does not recognize the MX29LV400CBCT as a bottom
- * -type device. This could cause risks of accidentally erasing critical
- * flash sectors. We thus define a single, write-protected partition covering
- * the whole flash.
- * TODO: once the flash part TOP/BOTTOM detection issue is sorted out in the MTD
- * code, break this into at least three partitions: 'u-boot code', 'u-boot
- * environment' and 'whatever is left'.
- */
-
-static struct mtd_partition edmini_v2_partitions[] = {
-	{
-		.name		= "Full512kb",
-		.size		= 0x00080000,
-		.offset		= 0x00000000,
-		.mask_flags	= MTD_WRITEABLE,
-	},
-};
-
-static struct physmap_flash_data edmini_v2_nor_flash_data = {
-	.width		= 1,
-	.parts		= edmini_v2_partitions,
-	.nr_parts	= ARRAY_SIZE(edmini_v2_partitions),
-};
-
-static struct resource edmini_v2_nor_flash_resource = {
-	.flags			= IORESOURCE_MEM,
-	.start			= EDMINI_V2_NOR_BOOT_BASE,
-	.end			= EDMINI_V2_NOR_BOOT_BASE
-		+ EDMINI_V2_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device edmini_v2_nor_flash = {
-	.name			= "physmap-flash",
-	.id			= 0,
-	.dev		= {
-		.platform_data	= &edmini_v2_nor_flash_data,
-	},
-	.num_resources		= 1,
-	.resource		= &edmini_v2_nor_flash_resource,
-};
-
-/*****************************************************************************
- * RTC 5C372a on I2C bus
- ****************************************************************************/
-
-#define EDMINIV2_RTC_GPIO	3
-
-static struct i2c_board_info __initdata edmini_v2_i2c_rtc = {
-	I2C_BOARD_INFO("rs5c372a", 0x32),
-	.irq = 0,
-};
-
-/*****************************************************************************
- * General Setup
- ****************************************************************************/
-static unsigned int edminiv2_mpp_modes[] __initdata = {
-	MPP0_UNUSED,
-	MPP1_UNUSED,
-	MPP2_UNUSED,
-	MPP3_GPIO,	/* RTC interrupt */
-	MPP4_UNUSED,
-	MPP5_UNUSED,
-	MPP6_UNUSED,
-	MPP7_UNUSED,
-	MPP8_UNUSED,
-	MPP9_UNUSED,
-	MPP10_UNUSED,
-	MPP11_UNUSED,
-	MPP12_SATA_LED,	/* SATA 0 presence */
-	MPP13_SATA_LED,	/* SATA 1 presence */
-	MPP14_SATA_LED,	/* SATA 0 active */
-	MPP15_SATA_LED,	/* SATA 1 active */
-	/* 16: Power LED control (0 = On, 1 = Off) */
-	MPP16_GPIO,
-	/* 17: Power LED control select (0 = CPLD, 1 = GPIO16) */
-	MPP17_GPIO,
-	/* 18: Power button status (0 = Released, 1 = Pressed) */
-	MPP18_GPIO,
-	MPP19_UNUSED,
-	0,
-};
-
-void __init edmini_v2_init(void)
-{
-	orion5x_mpp_conf(edminiv2_mpp_modes);
-
-	/*
-	 * Configure peripherals.
-	 */
-	orion5x_ehci0_init();
-
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-				    EDMINI_V2_NOR_BOOT_BASE,
-				    EDMINI_V2_NOR_BOOT_SIZE);
-	platform_device_register(&edmini_v2_nor_flash);
-
-	pr_notice("edmini_v2: USB device port, flash write and power-off "
-		  "are not yet supported.\n");
-
-	/* Get RTC IRQ and register the chip */
-	if (gpio_request(EDMINIV2_RTC_GPIO, "rtc") == 0) {
-		if (gpio_direction_input(EDMINIV2_RTC_GPIO) == 0)
-			edmini_v2_i2c_rtc.irq = gpio_to_irq(EDMINIV2_RTC_GPIO);
-		else
-			gpio_free(EDMINIV2_RTC_GPIO);
-	}
-
-	if (edmini_v2_i2c_rtc.irq == 0)
-		pr_warning("edmini_v2: failed to get RTC IRQ\n");
-
-	i2c_register_board_info(0, &edmini_v2_i2c_rtc, 1);
-}
diff --git a/arch/arm/mach-orion5x/irq.c b/arch/arm/mach-orion5x/irq.c
index 9654b0cc589..cd4bac4d7e4 100644
--- a/arch/arm/mach-orion5x/irq.c
+++ b/arch/arm/mach-orion5x/irq.c
@@ -16,6 +16,7 @@
 #include <mach/bridge-regs.h>
 #include <plat/orion-gpio.h>
 #include <plat/irq.h>
+#include <asm/exception.h>
 #include "common.h"
 
 static int __initdata gpio0_irqs[4] = {
@@ -25,10 +26,37 @@ static int __initdata gpio0_irqs[4] = {
 	IRQ_ORION5X_GPIO_24_31,
 };
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+/*
+ * Compiling with both non-DT and DT support enabled, will
+ * break asm irq handler used by non-DT boards. Therefore,
+ * we provide a C-style irq handler even for non-DT boards,
+ * if MULTI_IRQ_HANDLER is set.
+ */
+
+asmlinkage void
+__exception_irq_entry orion5x_legacy_handle_irq(struct pt_regs *regs)
+{
+	u32 stat;
+
+	stat = readl_relaxed(MAIN_IRQ_CAUSE);
+	stat &= readl_relaxed(MAIN_IRQ_MASK);
+	if (stat) {
+		unsigned int hwirq = __fls(stat);
+		handle_IRQ(hwirq, regs);
+		return;
+	}
+}
+#endif
+
 void __init orion5x_init_irq(void)
 {
 	orion_irq_init(0, MAIN_IRQ_MASK);
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+	set_handle_irq(orion5x_legacy_handle_irq);
+#endif
+
 	/*
 	 * Initialize gpiolib for GPIOs 0-31.
 	 */
diff --git a/arch/arm/mach-orion5x/mss2-setup.c b/arch/arm/mach-orion5x/mss2-setup.c
deleted file mode 100644
index e105130ba51..00000000000
--- a/arch/arm/mach-orion5x/mss2-setup.c
+++ /dev/null
@@ -1,274 +0,0 @@
-/*
- * Maxtor Shared Storage II Board Setup
- *
- * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include <mach/bridge-regs.h>
-#include "common.h"
-#include "mpp.h"
-
-#define MSS2_NOR_BOOT_BASE	0xff800000
-#define MSS2_NOR_BOOT_SIZE	SZ_256K
-
-/*****************************************************************************
- * Maxtor Shared Storage II Info
- ****************************************************************************/
-
-/*
- * Maxtor Shared Storage II hardware :
- * - Marvell 88F5182-A2 C500
- * - Marvell 88E1111 Gigabit Ethernet PHY
- * - RTC M41T81 (@0x68) on I2C bus
- * - 256KB NOR flash
- * - 64MB of RAM
- */
-
-/*****************************************************************************
- * 256KB NOR Flash on BOOT Device
- ****************************************************************************/
-
-static struct physmap_flash_data mss2_nor_flash_data = {
-	.width		= 1,
-};
-
-static struct resource mss2_nor_flash_resource = {
-	.flags		= IORESOURCE_MEM,
-	.start		= MSS2_NOR_BOOT_BASE,
-	.end		= MSS2_NOR_BOOT_BASE + MSS2_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device mss2_nor_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &mss2_nor_flash_data,
-	},
-	.resource	= &mss2_nor_flash_resource,
-	.num_resources	= 1,
-};
-
-/****************************************************************************
- * PCI setup
- ****************************************************************************/
-static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	int irq;
-
-	/*
-	 * Check for devices with hard-wired IRQs.
-	 */
-	irq = orion5x_pci_map_irq(dev, slot, pin);
-	if (irq != -1)
-		return irq;
-
-	return -1;
-}
-
-static struct hw_pci mss2_pci __initdata = {
-	.nr_controllers = 2,
-	.setup		= orion5x_pci_sys_setup,
-	.scan		= orion5x_pci_sys_scan_bus,
-	.map_irq	= mss2_pci_map_irq,
-};
-
-static int __init mss2_pci_init(void)
-{
-	if (machine_is_mss2())
-		pci_common_init(&mss2_pci);
-
-	return 0;
-}
-subsys_initcall(mss2_pci_init);
-
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data mss2_eth_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data mss2_sata_data = {
-	.n_ports	= 2,
-};
-
-/*****************************************************************************
- * GPIO buttons
- ****************************************************************************/
-
-#define MSS2_GPIO_KEY_RESET	12
-#define MSS2_GPIO_KEY_POWER	11
-
-static struct gpio_keys_button mss2_buttons[] = {
-	{
-		.code		= KEY_POWER,
-		.gpio		= MSS2_GPIO_KEY_POWER,
-		.desc		= "Power",
-		.active_low	= 1,
-	}, {
-		.code		= KEY_RESTART,
-		.gpio		= MSS2_GPIO_KEY_RESET,
-		.desc		= "Reset",
-		.active_low	= 1,
-	},
-};
-
-static struct gpio_keys_platform_data mss2_button_data = {
-	.buttons	= mss2_buttons,
-	.nbuttons	= ARRAY_SIZE(mss2_buttons),
-};
-
-static struct platform_device mss2_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &mss2_button_data,
-	},
-};
-
-/*****************************************************************************
- * RTC m41t81 on I2C bus
- ****************************************************************************/
-
-#define MSS2_GPIO_RTC_IRQ	3
-
-static struct i2c_board_info __initdata mss2_i2c_rtc = {
-	I2C_BOARD_INFO("m41t81", 0x68),
-};
-
-/*****************************************************************************
- * MSS2 power off method
- ****************************************************************************/
-/*
- * On the Maxtor Shared Storage II, the shutdown process is the following :
- * - Userland modifies U-boot env to tell U-boot to go idle at next boot
- * - The board reboots
- * - U-boot starts and go into an idle mode until the user press "power"
- */
-static void mss2_power_off(void)
-{
-	u32 reg;
-
-	/*
-	 * Enable and issue soft reset
-	 */
-	reg = readl(RSTOUTn_MASK);
-	reg |= 1 << 2;
-	writel(reg, RSTOUTn_MASK);
-
-	reg = readl(CPU_SOFT_RESET);
-	reg |= 1;
-	writel(reg, CPU_SOFT_RESET);
-}
-
-/****************************************************************************
- * General Setup
- ****************************************************************************/
-static unsigned int mss2_mpp_modes[] __initdata = {
-	MPP0_GPIO,		/* Power LED */
-	MPP1_GPIO,		/* Error LED */
-	MPP2_UNUSED,
-	MPP3_GPIO,		/* RTC interrupt */
-	MPP4_GPIO,		/* HDD ind. (Single/Dual)*/
-	MPP5_GPIO,		/* HD0 5V control */
-	MPP6_GPIO,		/* HD0 12V control */
-	MPP7_GPIO,		/* HD1 5V control */
-	MPP8_GPIO,		/* HD1 12V control */
-	MPP9_UNUSED,
-	MPP10_GPIO,		/* Fan control */
-	MPP11_GPIO,		/* Power button */
-	MPP12_GPIO,		/* Reset button */
-	MPP13_UNUSED,
-	MPP14_SATA_LED,		/* SATA 0 active */
-	MPP15_SATA_LED,		/* SATA 1 active */
-	MPP16_UNUSED,
-	MPP17_UNUSED,
-	MPP18_UNUSED,
-	MPP19_UNUSED,
-	0,
-};
-
-static void __init mss2_init(void)
-{
-	/* Setup basic Orion functions. Need to be called early. */
-	orion5x_init();
-
-	orion5x_mpp_conf(mss2_mpp_modes);
-
-	/*
-	 * MPP[20] Unused
-	 * MPP[21] PCI clock
-	 * MPP[22] USB 0 over current
-	 * MPP[23] USB 1 over current
-	 */
-
-	/*
-	 * Configure peripherals.
-	 */
-	orion5x_ehci0_init();
-	orion5x_ehci1_init();
-	orion5x_eth_init(&mss2_eth_data);
-	orion5x_i2c_init();
-	orion5x_sata_init(&mss2_sata_data);
-	orion5x_uart0_init();
-	orion5x_xor_init();
-
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-				    MSS2_NOR_BOOT_BASE,
-				    MSS2_NOR_BOOT_SIZE);
-	platform_device_register(&mss2_nor_flash);
-
-	platform_device_register(&mss2_button_device);
-
-	if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) {
-		if (gpio_direction_input(MSS2_GPIO_RTC_IRQ) == 0)
-			mss2_i2c_rtc.irq = gpio_to_irq(MSS2_GPIO_RTC_IRQ);
-		else
-			gpio_free(MSS2_GPIO_RTC_IRQ);
-	}
-	i2c_register_board_info(0, &mss2_i2c_rtc, 1);
-
-	/* register mss2 specific power-off method */
-	pm_power_off = mss2_power_off;
-}
-
-MACHINE_START(MSS2, "Maxtor Shared Storage II")
-	/* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
-	.atag_offset	= 0x100,
-	.init_machine	= mss2_init,
-	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion5x_init_irq,
-	.init_time	= orion5x_timer_init,
-	.fixup		= tag_fixup_mem32,
-	.restart	= orion5x_restart,
-MACHINE_END