Merge branch 'perf/core' into perf/uprobes

Merge in latest upstream (and the latest perf development tree),
to prepare for tooling changes, and also to pick up v3.4 MM
changes that the uprobes code needs to take care of.

Signed-off-by: Ingo Molnar <mingo@kernel.org>

1 files changed, 140 insertions, 54 deletions

diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c
index 0c4b76ab4d8..375d3f779a8 100644
--- a/arch/arm/mach-sa1100/assabet.c
+++ b/arch/arm/mach-sa1100/assabet.c
@@ -15,14 +15,16 @@
 #include <linux/errno.h>
 #include <linux/ioport.h>
 #include <linux/serial_core.h>
+#include <linux/mfd/ucb1x00.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/delay.h>
 #include <linux/mm.h>
 
+#include <video/sa1100fb.h>
+
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
-#include <asm/irq.h>
 #include <asm/setup.h>
 #include <asm/page.h>
 #include <asm/pgtable-hwdef.h>
@@ -36,17 +38,18 @@
 #include <asm/mach/serial_sa1100.h>
 #include <mach/assabet.h>
 #include <mach/mcp.h>
+#include <mach/irqs.h>
 
 #include "generic.h"
 
 #define ASSABET_BCR_DB1110 \
-	(ASSABET_BCR_SPK_OFF    | ASSABET_BCR_QMUTE     | \
+	(ASSABET_BCR_SPK_OFF    | \
 	 ASSABET_BCR_LED_GREEN  | ASSABET_BCR_LED_RED   | \
 	 ASSABET_BCR_RS232EN    | ASSABET_BCR_LCD_12RGB | \
 	 ASSABET_BCR_IRDA_MD0)
 
 #define ASSABET_BCR_DB1111 \
-	(ASSABET_BCR_SPK_OFF    | ASSABET_BCR_QMUTE     | \
+	(ASSABET_BCR_SPK_OFF    | \
 	 ASSABET_BCR_LED_GREEN  | ASSABET_BCR_LED_RED   | \
 	 ASSABET_BCR_RS232EN    | ASSABET_BCR_LCD_12RGB | \
 	 ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \
@@ -69,31 +72,10 @@ void ASSABET_BCR_frob(unsigned int mask, unsigned int val)
 
 EXPORT_SYMBOL(ASSABET_BCR_frob);
 
-static void assabet_backlight_power(int on)
-{
-#ifndef ASSABET_PAL_VIDEO
-	if (on)
-		ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
-	else
-#endif
-		ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
-}
-
-/*
- * Turn on/off the backlight.  When turning the backlight on,
- * we wait 500us after turning it on so we don't cause the
- * supplies to droop when we enable the LCD controller (and
- * cause a hard reset.)
- */
-static void assabet_lcd_power(int on)
+static void assabet_ucb1x00_reset(enum ucb1x00_reset state)
 {
-#ifndef ASSABET_PAL_VIDEO
-	if (on) {
-		ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
-		udelay(500);
-	} else
-#endif
-		ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+	if (state == UCB_RST_PROBE)
+		ASSABET_BCR_set(ASSABET_BCR_CODEC_RST);
 }
 
 
@@ -152,15 +134,8 @@ static struct flash_platform_data assabet_flash_data = {
 };
 
 static struct resource assabet_flash_resources[] = {
-	{
-		.start	= SA1100_CS0_PHYS,
-		.end	= SA1100_CS0_PHYS + SZ_32M - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.start	= SA1100_CS1_PHYS,
-		.end	= SA1100_CS1_PHYS + SZ_32M - 1,
-		.flags	= IORESOURCE_MEM,
-	}
+	DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M),
+	DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M),
 };
 
 
@@ -199,18 +174,126 @@ static struct irda_platform_data assabet_irda_data = {
 	.set_speed	= assabet_irda_set_speed,
 };
 
+static struct ucb1x00_plat_data assabet_ucb1x00_data = {
+	.reset		= assabet_ucb1x00_reset,
+	.gpio_base	= -1,
+};
+
 static struct mcp_plat_data assabet_mcp_data = {
 	.mccr0		= MCCR0_ADM,
 	.sclk_rate	= 11981000,
+	.codec_pdata	= &assabet_ucb1x00_data,
+};
+
+static void assabet_lcd_set_visual(u32 visual)
+{
+	u_int is_true_color = visual == FB_VISUAL_TRUECOLOR;
+
+	if (machine_is_assabet()) {
+#if 1		// phase 4 or newer Assabet's
+		if (is_true_color)
+			ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
+		else
+			ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
+#else
+		// older Assabet's
+		if (is_true_color)
+			ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
+		else
+			ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
+#endif
+	}
+}
+
+#ifndef ASSABET_PAL_VIDEO
+static void assabet_lcd_backlight_power(int on)
+{
+	if (on)
+		ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
+	else
+		ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
+}
+
+/*
+ * Turn on/off the backlight.  When turning the backlight on, we wait
+ * 500us after turning it on so we don't cause the supplies to droop
+ * when we enable the LCD controller (and cause a hard reset.)
+ */
+static void assabet_lcd_power(int on)
+{
+	if (on) {
+		ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
+		udelay(500);
+	} else
+		ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+}
+
+/*
+ * The assabet uses a sharp LQ039Q2DS54 LCD module.  It is actually
+ * takes an RGB666 signal, but we provide it with an RGB565 signal
+ * instead (def_rgb_16).
+ */
+static struct sa1100fb_mach_info lq039q2ds54_info = {
+	.pixclock	= 171521,	.bpp		= 16,
+	.xres		= 320,		.yres		= 240,
+
+	.hsync_len	= 5,		.vsync_len	= 1,
+	.left_margin	= 61,		.upper_margin	= 3,
+	.right_margin	= 9,		.lower_margin	= 0,
+
+	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
+
+	.backlight_power = assabet_lcd_backlight_power,
+	.lcd_power = assabet_lcd_power,
+	.set_visual = assabet_lcd_set_visual,
+};
+#else
+static void assabet_pal_backlight_power(int on)
+{
+	ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
+}
+
+static void assabet_pal_power(int on)
+{
+	ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+}
+
+static struct sa1100fb_mach_info pal_info = {
+	.pixclock	= 67797,	.bpp		= 16,
+	.xres		= 640,		.yres		= 512,
+
+	.hsync_len	= 64,		.vsync_len	= 6,
+	.left_margin	= 125,		.upper_margin	= 70,
+	.right_margin	= 115,		.lower_margin	= 36,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
+
+	.backlight_power = assabet_pal_backlight_power,
+	.lcd_power = assabet_pal_power,
+	.set_visual = assabet_lcd_set_visual,
 };
+#endif
+
+#ifdef CONFIG_ASSABET_NEPONSET
+static struct resource neponset_resources[] = {
+	DEFINE_RES_MEM(0x10000000, 0x08000000),
+	DEFINE_RES_MEM(0x18000000, 0x04000000),
+	DEFINE_RES_MEM(0x40000000, SZ_8K),
+	DEFINE_RES_IRQ(IRQ_GPIO25),
+};
+#endif
 
 static void __init assabet_init(void)
 {
 	/*
 	 * Ensure that the power supply is in "high power" mode.
 	 */
-	GPDR |= GPIO_GPIO16;
 	GPSR = GPIO_GPIO16;
+	GPDR |= GPIO_GPIO16;
 
 	/*
 	 * Ensure that these pins are set as outputs and are driving
@@ -218,8 +301,16 @@ static void __init assabet_init(void)
 	 * the WS latch in the CPLD, and we don't float causing
 	 * excessive power drain.  --rmk
 	 */
-	GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
 	GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+	GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+
+	/*
+	 * Also set GPIO27 as an output; this is used to clock UART3
+	 * via the FPGA and as otherwise has no pullups or pulldowns,
+	 * so stop it floating.
+	 */
+	GPCR = GPIO_GPIO27;
+	GPDR |= GPIO_GPIO27;
 
 	/*
 	 * Set up registers for sleep mode.
@@ -231,8 +322,7 @@ static void __init assabet_init(void)
 	PPDR |= PPC_TXD3 | PPC_TXD1;
 	PPSR |= PPC_TXD3 | PPC_TXD1;
 
-	sa1100fb_lcd_power = assabet_lcd_power;
-	sa1100fb_backlight_power = assabet_backlight_power;
+	sa11x0_ppc_configure_mcp();
 
 	if (machine_has_neponset()) {
 		/*
@@ -246,9 +336,17 @@ static void __init assabet_init(void)
 #ifndef CONFIG_ASSABET_NEPONSET
 		printk( "Warning: Neponset detected but full support "
 			"hasn't been configured in the kernel\n" );
+#else
+		platform_device_register_simple("neponset", 0,
+			neponset_resources, ARRAY_SIZE(neponset_resources));
 #endif
 	}
 
+#ifndef ASSABET_PAL_VIDEO
+	sa11x0_register_lcd(&lq039q2ds54_info);
+#else
+	sa11x0_register_lcd(&pal_video);
+#endif
 	sa11x0_register_mtd(&assabet_flash_data, assabet_flash_resources,
 			    ARRAY_SIZE(assabet_flash_resources));
 	sa11x0_register_irda(&assabet_irda_data);
@@ -412,21 +510,8 @@ static void __init assabet_map_io(void)
 	 */
 	Ser1SDCR0 |= SDCR0_SUS;
 
-	if (machine_has_neponset()) {
-#ifdef CONFIG_ASSABET_NEPONSET
-		extern void neponset_map_io(void);
-
-		/*
-		 * We map Neponset registers even if it isn't present since
-		 * many drivers will try to probe their stuff (and fail).
-		 * This is still more friendly than a kernel paging request
-		 * crash.
-		 */
-		neponset_map_io();
-#endif
-	} else {
+	if (!machine_has_neponset())
 		sa1100_register_uart_fns(&assabet_port_fns);
-	}
 
 	/*
 	 * When Neponset is attached, the first UART should be
@@ -449,6 +534,7 @@ MACHINE_START(ASSABET, "Intel-Assabet")
 	.atag_offset	= 0x100,
 	.fixup		= fixup_assabet,
 	.map_io		= assabet_map_io,
+	.nr_irqs	= SA1100_NR_IRQS,
 	.init_irq	= sa1100_init_irq,
 	.timer		= &sa1100_timer,
 	.init_machine	= assabet_init,