Merge branch 'master' into percpu

Conflicts:
	arch/powerpc/platforms/pseries/hvCall.S
	include/linux/percpu.h

6 files changed, 143 insertions, 225 deletions

diff --git a/arch/arm/mach-sa1100/include/mach/collie.h b/arch/arm/mach-sa1100/include/mach/collie.h
index 9efb569cdb6..71a0b3fdcc8 100644
--- a/arch/arm/mach-sa1100/include/mach/collie.h
+++ b/arch/arm/mach-sa1100/include/mach/collie.h
@@ -25,29 +25,39 @@
 #define COLLIE_GPIO_VPEN	(COLLIE_SCOOP_GPIO_BASE + 7)
 #define COLLIE_SCP_LB_VOL_CHG	SCOOP_GPCR_PA19
 
-#define COLLIE_SCOOP_IO_DIR	( COLLIE_SCP_MUTE_L | COLLIE_SCP_MUTE_R | \
+#define COLLIE_SCOOP_IO_DIR	(COLLIE_SCP_MUTE_L | COLLIE_SCP_MUTE_R | \
 				COLLIE_SCP_5VON | COLLIE_SCP_AMP_ON | \
-				COLLIE_SCP_LB_VOL_CHG )
-#define COLLIE_SCOOP_IO_OUT	( COLLIE_SCP_MUTE_L | COLLIE_SCP_MUTE_R )
+				COLLIE_SCP_LB_VOL_CHG)
+#define COLLIE_SCOOP_IO_OUT	(COLLIE_SCP_MUTE_L | COLLIE_SCP_MUTE_R)
 
-/* GPIOs for which the generic definition doesn't say much */
+/* GPIOs for gpiolib  */
 
-#define COLLIE_GPIO_ON_KEY		GPIO_GPIO (0)
-#define COLLIE_GPIO_AC_IN		GPIO_GPIO (1)
-#define COLLIE_GPIO_SDIO_INT		GPIO_GPIO (11)
-#define COLLIE_GPIO_CF_IRQ		GPIO_GPIO (14)
-#define COLLIE_GPIO_nREMOCON_INT	GPIO_GPIO (15)
-#define COLLIE_GPIO_UCB1x00_RESET	GPIO_GPIO (16)
-#define COLLIE_GPIO_nMIC_ON		GPIO_GPIO (17)
-#define COLLIE_GPIO_nREMOCON_ON		GPIO_GPIO (18)
-#define COLLIE_GPIO_CO			GPIO_GPIO (20)
-#define COLLIE_GPIO_MCP_CLK		GPIO_GPIO (21)
-#define COLLIE_GPIO_CF_CD		GPIO_GPIO (22)
-#define COLLIE_GPIO_UCB1x00_IRQ		GPIO_GPIO (23)
-#define COLLIE_GPIO_WAKEUP		GPIO_GPIO (24)
-#define COLLIE_GPIO_GA_INT		GPIO_GPIO (25)
-#define COLLIE_GPIO_MAIN_BAT_LOW	GPIO_GPIO (26)
+#define COLLIE_GPIO_ON_KEY		(0)
+#define COLLIE_GPIO_AC_IN		(1)
+#define COLLIE_GPIO_SDIO_INT		(11)
+#define COLLIE_GPIO_CF_IRQ		(14)
+#define COLLIE_GPIO_nREMOCON_INT	(15)
+#define COLLIE_GPIO_UCB1x00_RESET	(16)
+#define COLLIE_GPIO_nMIC_ON		(17)
+#define COLLIE_GPIO_nREMOCON_ON		(18)
+#define COLLIE_GPIO_CO			(20)
+#define COLLIE_GPIO_MCP_CLK		(21)
+#define COLLIE_GPIO_CF_CD		(22)
+#define COLLIE_GPIO_UCB1x00_IRQ		(23)
+#define COLLIE_GPIO_WAKEUP		(24)
+#define COLLIE_GPIO_GA_INT		(25)
+#define COLLIE_GPIO_MAIN_BAT_LOW	(26)
 
+/* GPIO definitions for direct register access */
+
+#define _COLLIE_GPIO_ON_KEY		GPIO_GPIO(0)
+#define _COLLIE_GPIO_AC_IN		GPIO_GPIO(1)
+#define _COLLIE_GPIO_nREMOCON_INT	GPIO_GPIO(15)
+#define _COLLIE_GPIO_UCB1x00_RESET	GPIO_GPIO(16)
+#define _COLLIE_GPIO_nMIC_ON		GPIO_GPIO(17)
+#define _COLLIE_GPIO_nREMOCON_ON	GPIO_GPIO(18)
+#define _COLLIE_GPIO_CO			GPIO_GPIO(20)
+#define _COLLIE_GPIO_WAKEUP		GPIO_GPIO(24)
 /* Interrupts */
 
 #define COLLIE_IRQ_GPIO_ON_KEY		IRQ_GPIO0
@@ -70,19 +80,20 @@
 #define COLLIE_LCM_IRQ_GPIO_nSD_WP	IRQ_LOCOMO_GPIO14
 
 /* GPIO's on the TC35143AF (Toshiba Analog Frontend) */
-#define COLLIE_TC35143_GPIO_VERSION0    UCB_IO_0	/* GPIO0=Version                 */
-#define COLLIE_TC35143_GPIO_TBL_CHK     UCB_IO_1	/* GPIO1=TBL_CHK                 */
-#define COLLIE_TC35143_GPIO_VPEN_ON     UCB_IO_2	/* GPIO2=VPNE_ON                 */
-#define COLLIE_TC35143_GPIO_IR_ON       UCB_IO_3	/* GPIO3=IR_ON                   */
-#define COLLIE_TC35143_GPIO_AMP_ON      UCB_IO_4	/* GPIO4=AMP_ON                  */
-#define COLLIE_TC35143_GPIO_VERSION1    UCB_IO_5	/* GPIO5=Version                 */
-#define COLLIE_TC35143_GPIO_FS8KLPF     UCB_IO_5	/* GPIO5=fs 8k LPF               */
-#define COLLIE_TC35143_GPIO_BUZZER_BIAS UCB_IO_6	/* GPIO6=BUZZER BIAS             */
-#define COLLIE_TC35143_GPIO_MBAT_ON     UCB_IO_7	/* GPIO7=MBAT_ON                 */
-#define COLLIE_TC35143_GPIO_BBAT_ON     UCB_IO_8	/* GPIO8=BBAT_ON                 */
-#define COLLIE_TC35143_GPIO_TMP_ON      UCB_IO_9	/* GPIO9=TMP_ON                  */
-#define COLLIE_TC35143_GPIO_IN		( UCB_IO_0 | UCB_IO_2 | UCB_IO_5 )
-#define COLLIE_TC35143_GPIO_OUT		( UCB_IO_1 | UCB_IO_3 | UCB_IO_4 | UCB_IO_6 | \
-					UCB_IO_7 | UCB_IO_8 | UCB_IO_9 )
+#define COLLIE_TC35143_GPIO_BASE	(GPIO_MAX + 13)
+#define COLLIE_TC35143_GPIO_VERSION0    UCB_IO_0
+#define COLLIE_TC35143_GPIO_TBL_CHK     UCB_IO_1
+#define COLLIE_TC35143_GPIO_VPEN_ON     UCB_IO_2
+#define COLLIE_TC35143_GPIO_IR_ON       UCB_IO_3
+#define COLLIE_TC35143_GPIO_AMP_ON      UCB_IO_4
+#define COLLIE_TC35143_GPIO_VERSION1    UCB_IO_5
+#define COLLIE_TC35143_GPIO_FS8KLPF     UCB_IO_5
+#define COLLIE_TC35143_GPIO_BUZZER_BIAS UCB_IO_6
+#define COLLIE_GPIO_MBAT_ON     	(COLLIE_TC35143_GPIO_BASE + 7)
+#define COLLIE_GPIO_BBAT_ON     	(COLLIE_TC35143_GPIO_BASE + 8)
+#define COLLIE_GPIO_TMP_ON      	(COLLIE_TC35143_GPIO_BASE + 9)
+#define COLLIE_TC35143_GPIO_IN		(UCB_IO_0 | UCB_IO_2 | UCB_IO_5)
+#define COLLIE_TC35143_GPIO_OUT		(UCB_IO_1 | UCB_IO_3 | UCB_IO_4 \
+						| UCB_IO_6)
 
 #endif
diff --git a/arch/arm/mach-sa1100/include/mach/gpio.h b/arch/arm/mach-sa1100/include/mach/gpio.h
index 582a0c92da5..7befc104e9a 100644
--- a/arch/arm/mach-sa1100/include/mach/gpio.h
+++ b/arch/arm/mach-sa1100/include/mach/gpio.h
@@ -49,20 +49,9 @@ static inline void gpio_set_value(unsigned gpio, int value)
 
 #define gpio_cansleep	__gpio_cansleep
 
-static inline unsigned gpio_to_irq(unsigned gpio)
-{
-	if (gpio < 11)
-		return IRQ_GPIO0 + gpio;
-	else
-		return IRQ_GPIO11 - 11 + gpio;
-}
-
-static inline unsigned irq_to_gpio(unsigned irq)
-{
-	if (irq < IRQ_GPIO11_27)
-		return irq - IRQ_GPIO0;
-	else
-		return irq - IRQ_GPIO11 + 11;
-}
+#define gpio_to_irq(gpio)	((gpio < 11) ? (IRQ_GPIO0 + gpio) : \
+					(IRQ_GPIO11 - 11 + gpio))
+#define irq_to_gpio(irq)	((irq < IRQ_GPIO11_27) ? (irq - IRQ_GPIO0) : \
+					(irq - IRQ_GPIO11 + 11))
 
 #endif
diff --git a/arch/arm/mach-sa1100/include/mach/h3600.h b/arch/arm/mach-sa1100/include/mach/h3600.h
deleted file mode 100644
index 2827faa4742..00000000000
--- a/arch/arm/mach-sa1100/include/mach/h3600.h
+++ /dev/null
@@ -1,100 +0,0 @@
-/*
- *
- * Definitions for H3600 Handheld Computer
- *
- * Copyright 2000 Compaq Computer Corporation.
- *
- * Use consistent with the GNU GPL is permitted,
- * provided that this copyright notice is
- * preserved in its entirety in all copies and derived works.
- *
- * COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
- * AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS
- * FITNESS FOR ANY PARTICULAR PURPOSE.
- *
- * Author: Jamey Hicks.
- *
- * History:
- *
- * 2001-10-??	Andrew Christian   Added support for iPAQ H3800
- *
- */
-
-#ifndef _INCLUDE_H3600_H_
-#define _INCLUDE_H3600_H_
-
-typedef int __bitwise pm_request_t;
-
-#define PM_SUSPEND	((__force pm_request_t) 1)	/* enter D1-D3 */
-#define PM_RESUME	((__force pm_request_t) 2)	/* enter D0 */
-
-/* generalized support for H3xxx series Compaq Pocket PC's */
-#define machine_is_h3xxx() (machine_is_h3100() || machine_is_h3600())
-
-/* Physical memory regions corresponding to chip selects */
-#define H3600_EGPIO_PHYS	(SA1100_CS5_PHYS + 0x01000000)
-#define H3600_BANK_2_PHYS	SA1100_CS2_PHYS
-#define H3600_BANK_4_PHYS	SA1100_CS4_PHYS
-
-/* Virtual memory regions corresponding to chip selects 2 & 4 (used on sleeves) */
-#define H3600_EGPIO_VIRT	0xf0000000
-#define H3600_BANK_2_VIRT	0xf1000000
-#define H3600_BANK_4_VIRT	0xf3800000
-
-/*
-   Machine-independent GPIO definitions
-   --- these are common across all current iPAQ platforms
-*/
-
-#define GPIO_H3600_NPOWER_BUTTON	GPIO_GPIO (0)	/* Also known as the "off button"  */
-
-#define GPIO_H3600_PCMCIA_CD1		GPIO_GPIO (10)
-#define GPIO_H3600_PCMCIA_IRQ1		GPIO_GPIO (11)
-
-/* UDA1341 L3 Interface */
-#define GPIO_H3600_L3_DATA		GPIO_GPIO (14)
-#define GPIO_H3600_L3_MODE		GPIO_GPIO (15)
-#define GPIO_H3600_L3_CLOCK		GPIO_GPIO (16)
-
-#define GPIO_H3600_PCMCIA_CD0		GPIO_GPIO (17)
-#define GPIO_H3600_SYS_CLK		GPIO_GPIO (19)
-#define GPIO_H3600_PCMCIA_IRQ0		GPIO_GPIO (21)
-
-#define GPIO_H3600_COM_DCD		GPIO_GPIO (23)
-#define GPIO_H3600_OPT_IRQ		GPIO_GPIO (24)
-#define GPIO_H3600_COM_CTS		GPIO_GPIO (25)
-#define GPIO_H3600_COM_RTS		GPIO_GPIO (26)
-
-#define IRQ_GPIO_H3600_NPOWER_BUTTON	IRQ_GPIO0
-#define IRQ_GPIO_H3600_PCMCIA_CD1	IRQ_GPIO10
-#define IRQ_GPIO_H3600_PCMCIA_IRQ1	IRQ_GPIO11
-#define IRQ_GPIO_H3600_PCMCIA_CD0	IRQ_GPIO17
-#define IRQ_GPIO_H3600_PCMCIA_IRQ0	IRQ_GPIO21
-#define IRQ_GPIO_H3600_COM_DCD		IRQ_GPIO23
-#define IRQ_GPIO_H3600_OPT_IRQ		IRQ_GPIO24
-#define IRQ_GPIO_H3600_COM_CTS		IRQ_GPIO25
-
-
-#ifndef __ASSEMBLY__
-
-enum ipaq_egpio_type {
-	IPAQ_EGPIO_LCD_POWER,	  /* Power to the LCD panel */
-	IPAQ_EGPIO_CODEC_NRESET,  /* Clear to reset the audio codec (remember to return high) */
-	IPAQ_EGPIO_AUDIO_ON,	  /* Audio power */
-	IPAQ_EGPIO_QMUTE,	  /* Audio muting */
-	IPAQ_EGPIO_OPT_NVRAM_ON,  /* Non-volatile RAM on extension sleeves (SPI interface) */
-	IPAQ_EGPIO_OPT_ON,	  /* Power to extension sleeves */
-	IPAQ_EGPIO_CARD_RESET,	  /* Reset PCMCIA cards on extension sleeve (???) */
-	IPAQ_EGPIO_OPT_RESET,	  /* Reset option pack (???) */
-	IPAQ_EGPIO_IR_ON,	  /* IR sensor/emitter power */
-	IPAQ_EGPIO_IR_FSEL,	  /* IR speed selection 1->fast, 0->slow */
-	IPAQ_EGPIO_RS232_ON,	  /* Maxim RS232 chip power */
-	IPAQ_EGPIO_VPP_ON,	  /* Turn on power to flash programming */
-	IPAQ_EGPIO_LCD_ENABLE,	  /* Enable/disable LCD controller */
-};
-
-extern void (*assign_h3600_egpio)(enum ipaq_egpio_type x, int level);
-
-#endif /* ASSEMBLY */
-
-#endif /* _INCLUDE_H3600_H_ */
diff --git a/arch/arm/mach-sa1100/include/mach/h3600_gpio.h b/arch/arm/mach-sa1100/include/mach/h3600_gpio.h
deleted file mode 100644
index a36ca76d018..00000000000
--- a/arch/arm/mach-sa1100/include/mach/h3600_gpio.h
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- *
- * Definitions for H3600 Handheld Computer
- *
- * Copyright 2000 Compaq Computer Corporation.
- *
- * Use consistent with the GNU GPL is permitted,
- * provided that this copyright notice is
- * preserved in its entirety in all copies and derived works.
- *
- * COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
- * AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS
- * FITNESS FOR ANY PARTICULAR PURPOSE.
- *
- * Author: Jamey Hicks.
- *
- * History:
- *
- * 2001-10-??   Andrew Christian   Added support for iPAQ H3800
- *
- */
-
-#ifndef _INCLUDE_H3600_GPIO_H_
-#define _INCLUDE_H3600_GPIO_H_
-
-/*
- * GPIO lines that are common across ALL iPAQ models are in "h3600.h"
- * This file contains machine-specific definitions
- */
-
-#define GPIO_H3600_SUSPEND              GPIO_GPIO (0)
-/* GPIO[2:9] used by LCD on H3600/3800, used as GPIO on H3100 */
-#define GPIO_H3100_BT_ON		GPIO_GPIO (2)
-#define GPIO_H3100_GPIO3		GPIO_GPIO (3)
-#define GPIO_H3100_QMUTE		GPIO_GPIO (4)
-#define GPIO_H3100_LCD_3V_ON		GPIO_GPIO (5)
-#define GPIO_H3100_AUD_ON		GPIO_GPIO (6)
-#define GPIO_H3100_AUD_PWR_ON		GPIO_GPIO (7)
-#define GPIO_H3100_IR_ON		GPIO_GPIO (8)
-#define GPIO_H3100_IR_FSEL		GPIO_GPIO (9)
-
-/* for H3600, audio sample rate clock generator */
-#define GPIO_H3600_CLK_SET0		GPIO_GPIO (12)
-#define GPIO_H3600_CLK_SET1		GPIO_GPIO (13)
-
-#define GPIO_H3600_ACTION_BUTTON	GPIO_GPIO (18)
-#define GPIO_H3600_SOFT_RESET           GPIO_GPIO (20)   /* Also known as BATT_FAULT */
-#define GPIO_H3600_OPT_LOCK		GPIO_GPIO (22)
-#define GPIO_H3600_OPT_DET		GPIO_GPIO (27)
-
-/****************************************************/
-
-#define IRQ_GPIO_H3600_ACTION_BUTTON    IRQ_GPIO18
-#define IRQ_GPIO_H3600_OPT_DET		IRQ_GPIO27
-
-/* H3100 / 3600 EGPIO pins */
-#define EGPIO_H3600_VPP_ON		(1 << 0)
-#define EGPIO_H3600_CARD_RESET		(1 << 1)   /* reset the attached pcmcia/compactflash card.  active high. */
-#define EGPIO_H3600_OPT_RESET		(1 << 2)   /* reset the attached option pack.  active high. */
-#define EGPIO_H3600_CODEC_NRESET	(1 << 3)   /* reset the onboard UDA1341.  active low. */
-#define EGPIO_H3600_OPT_NVRAM_ON	(1 << 4)   /* apply power to optionpack nvram, active high. */
-#define EGPIO_H3600_OPT_ON		(1 << 5)   /* full power to option pack.  active high. */
-#define EGPIO_H3600_LCD_ON		(1 << 6)   /* enable 3.3V to LCD.  active high. */
-#define EGPIO_H3600_RS232_ON		(1 << 7)   /* UART3 transceiver force on.  Active high. */
-
-/* H3600 only EGPIO pins */
-#define EGPIO_H3600_LCD_PCI		(1 << 8)   /* LCD control IC enable.  active high. */
-#define EGPIO_H3600_IR_ON		(1 << 9)   /* apply power to IR module.  active high. */
-#define EGPIO_H3600_AUD_AMP_ON		(1 << 10)  /* apply power to audio power amp.  active high. */
-#define EGPIO_H3600_AUD_PWR_ON		(1 << 11)  /* apply power to reset of audio circuit.  active high. */
-#define EGPIO_H3600_QMUTE		(1 << 12)  /* mute control for onboard UDA1341.  active high. */
-#define EGPIO_H3600_IR_FSEL		(1 << 13)  /* IR speed select: 1->fast, 0->slow */
-#define EGPIO_H3600_LCD_5V_ON		(1 << 14)  /* enable 5V to LCD. active high. */
-#define EGPIO_H3600_LVDD_ON		(1 << 15)  /* enable 9V and -6.5V to LCD. */
-
-
-#endif /* _INCLUDE_H3600_GPIO_H_ */
diff --git a/arch/arm/mach-sa1100/include/mach/h3xxx.h b/arch/arm/mach-sa1100/include/mach/h3xxx.h
new file mode 100644
index 00000000000..7d9df16f04a
--- /dev/null
+++ b/arch/arm/mach-sa1100/include/mach/h3xxx.h
@@ -0,0 +1,94 @@
+/*
+ * Definitions for Compaq iPAQ H3100 and H3600 handheld computers
+ *
+ * (c) 2000 Compaq Computer Corporation. (Author: Jamey Hicks)
+ * (c) 2009 Dmitry Artamonow <mad_soft@inbox.ru>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef _INCLUDE_H3XXX_H_
+#define _INCLUDE_H3XXX_H_
+
+/* Physical memory regions corresponding to chip selects */
+#define H3600_EGPIO_PHYS	(SA1100_CS5_PHYS + 0x01000000)
+#define H3600_BANK_2_PHYS	SA1100_CS2_PHYS
+#define H3600_BANK_4_PHYS	SA1100_CS4_PHYS
+
+/* Virtual memory regions corresponding to chip selects 2 & 4 (used on sleeves) */
+#define H3600_EGPIO_VIRT	0xf0000000
+#define H3600_BANK_2_VIRT	0xf1000000
+#define H3600_BANK_4_VIRT	0xf3800000
+
+/*
+ * gpiolib numbers for all iPAQs
+ */
+#define H3XXX_GPIO_PWR_BUTTON		0
+#define H3XXX_GPIO_PCMCIA_CD1		10
+#define H3XXX_GPIO_PCMCIA_IRQ1		11
+#define H3XXX_GPIO_PCMCIA_CD0		17
+#define H3XXX_GPIO_ACTION_BUTTON	18
+#define H3XXX_GPIO_SYS_CLK		19
+#define H3XXX_GPIO_PCMCIA_IRQ0		21
+#define H3XXX_GPIO_COM_DCD		23
+#define H3XXX_GPIO_OPTION		24
+#define H3XXX_GPIO_COM_CTS		25
+#define H3XXX_GPIO_COM_RTS		26
+
+/* machine-specific gpios */
+
+#define H3100_GPIO_BT_ON		2
+#define H3100_GPIO_QMUTE		4
+#define H3100_GPIO_LCD_3V_ON		5
+#define H3100_GPIO_AUD_ON		6
+#define H3100_GPIO_AUD_PWR_ON		7
+#define H3100_GPIO_IR_ON		8
+#define H3100_GPIO_IR_FSEL		9
+
+#define H3600_GPIO_CLK_SET0		12	/* audio sample rate clock generator */
+#define H3600_GPIO_CLK_SET1		13
+#define H3600_GPIO_SOFT_RESET		20	/* also known as BATT_FAULT */
+#define H3600_GPIO_OPT_LOCK		22
+#define H3600_GPIO_OPT_DET		27
+
+
+/* H3100 / 3600 EGPIO pins */
+#define H3XXX_EGPIO_BASE		(GPIO_MAX + 1)
+
+#define H3XXX_EGPIO_VPP_ON		(H3XXX_EGPIO_BASE + 0)
+#define H3XXX_EGPIO_CARD_RESET		(H3XXX_EGPIO_BASE + 1) /* reset the attached pcmcia/compactflash card.  active high. */
+#define H3XXX_EGPIO_OPT_RESET		(H3XXX_EGPIO_BASE + 2) /* reset the attached option pack.  active high. */
+#define H3XXX_EGPIO_CODEC_NRESET	(H3XXX_EGPIO_BASE + 3) /* reset the onboard UDA1341.  active low. */
+#define H3XXX_EGPIO_OPT_NVRAM_ON	(H3XXX_EGPIO_BASE + 4) /* apply power to optionpack nvram, active high. */
+#define H3XXX_EGPIO_OPT_ON		(H3XXX_EGPIO_BASE + 5) /* full power to option pack.  active high. */
+#define H3XXX_EGPIO_LCD_ON		(H3XXX_EGPIO_BASE + 6) /* enable 3.3V to LCD.  active high. */
+#define H3XXX_EGPIO_RS232_ON		(H3XXX_EGPIO_BASE + 7) /* UART3 transceiver force on.  Active high. */
+
+/* H3600 only EGPIO pins */
+#define H3600_EGPIO_LCD_PCI		(H3XXX_EGPIO_BASE + 8) /* LCD control IC enable.  active high. */
+#define H3600_EGPIO_IR_ON		(H3XXX_EGPIO_BASE + 9) /* apply power to IR module.  active high. */
+#define H3600_EGPIO_AUD_AMP_ON		(H3XXX_EGPIO_BASE + 10) /* apply power to audio power amp.  active high. */
+#define H3600_EGPIO_AUD_PWR_ON		(H3XXX_EGPIO_BASE + 11) /* apply power to reset of audio circuit.  active high. */
+#define H3600_EGPIO_QMUTE		(H3XXX_EGPIO_BASE + 12) /* mute control for onboard UDA1341.  active high. */
+#define H3600_EGPIO_IR_FSEL		(H3XXX_EGPIO_BASE + 13) /* IR speed select: 1->fast, 0->slow */
+#define H3600_EGPIO_LCD_5V_ON		(H3XXX_EGPIO_BASE + 14) /* enable 5V to LCD. active high. */
+#define H3600_EGPIO_LVDD_ON		(H3XXX_EGPIO_BASE + 15) /* enable 9V and -6.5V to LCD. */
+
+struct gpio_default_state {
+	int gpio;
+	int mode;
+	const char *name;
+};
+
+#define GPIO_MODE_IN	-1
+#define GPIO_MODE_OUT0	0
+#define GPIO_MODE_OUT1	1
+
+void h3xxx_init_gpio(struct gpio_default_state *s, size_t n);
+void __init h3xxx_map_io(void);
+void __init h3xxx_mach_init(void);
+
+#endif /* _INCLUDE_H3XXX_H_ */
diff --git a/arch/arm/mach-sa1100/include/mach/mcp.h b/arch/arm/mach-sa1100/include/mach/mcp.h
index fb8b09a57ad..ed1a331508a 100644
--- a/arch/arm/mach-sa1100/include/mach/mcp.h
+++ b/arch/arm/mach-sa1100/include/mach/mcp.h
@@ -16,6 +16,7 @@ struct mcp_plat_data {
 	u32 mccr0;
 	u32 mccr1;
 	unsigned int sclk_rate;
+	int gpio_base;
 };
 
 #endif