Merge tag 'efi-urgent' into x86/urgent

 * Avoid WARN_ON() when mapping BGRT on Baytrail (EFI 32-bit).

Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

1 files changed, 189 insertions, 1 deletions

diff --git a/arch/arm/mach-shmobile/board-koelsch.c b/arch/arm/mach-shmobile/board-koelsch.c
index ace1711a6cd..de7cc64b1f3 100644
--- a/arch/arm/mach-shmobile/board-koelsch.c
+++ b/arch/arm/mach-shmobile/board-koelsch.c
@@ -19,18 +19,205 @@
  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  */
 
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
 #include <linux/kernel.h>
+#include <linux/leds.h>
+#include <linux/phy.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/platform_data/gpio-rcar.h>
+#include <linux/platform_data/rcar-du.h>
 #include <linux/platform_device.h>
+#include <linux/sh_eth.h>
 #include <mach/common.h>
+#include <mach/irqs.h>
 #include <mach/r8a7791.h>
 #include <mach/rcar-gen2.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
+/* DU */
+static struct rcar_du_encoder_data koelsch_du_encoders[] = {
+	{
+		.type = RCAR_DU_ENCODER_NONE,
+		.output = RCAR_DU_OUTPUT_LVDS0,
+		.connector.lvds.panel = {
+			.width_mm = 210,
+			.height_mm = 158,
+			.mode = {
+				.clock = 65000,
+				.hdisplay = 1024,
+				.hsync_start = 1048,
+				.hsync_end = 1184,
+				.htotal = 1344,
+				.vdisplay = 768,
+				.vsync_start = 771,
+				.vsync_end = 777,
+				.vtotal = 806,
+				.flags = 0,
+			},
+		},
+	},
+};
+
+static const struct rcar_du_platform_data koelsch_du_pdata __initconst = {
+	.encoders = koelsch_du_encoders,
+	.num_encoders = ARRAY_SIZE(koelsch_du_encoders),
+};
+
+static const struct resource du_resources[] __initconst = {
+	DEFINE_RES_MEM(0xfeb00000, 0x40000),
+	DEFINE_RES_MEM_NAMED(0xfeb90000, 0x1c, "lvds.0"),
+	DEFINE_RES_IRQ(gic_spi(256)),
+	DEFINE_RES_IRQ(gic_spi(268)),
+};
+
+static void __init koelsch_add_du_device(void)
+{
+	struct platform_device_info info = {
+		.name = "rcar-du-r8a7791",
+		.id = -1,
+		.res = du_resources,
+		.num_res = ARRAY_SIZE(du_resources),
+		.data = &koelsch_du_pdata,
+		.size_data = sizeof(koelsch_du_pdata),
+		.dma_mask = DMA_BIT_MASK(32),
+	};
+
+	platform_device_register_full(&info);
+}
+
+/* Ether */
+static const struct sh_eth_plat_data ether_pdata __initconst = {
+	.phy			= 0x1,
+	.edmac_endian		= EDMAC_LITTLE_ENDIAN,
+	.phy_interface		= PHY_INTERFACE_MODE_RMII,
+	.ether_link_active_low	= 1,
+};
+
+static const struct resource ether_resources[] __initconst = {
+	DEFINE_RES_MEM(0xee700000, 0x400),
+	DEFINE_RES_IRQ(gic_spi(162)),
+};
+
+/* LEDS */
+static struct gpio_led koelsch_leds[] = {
+	{
+		.name		= "led8",
+		.gpio		= RCAR_GP_PIN(2, 21),
+		.default_state	= LEDS_GPIO_DEFSTATE_ON,
+	}, {
+		.name		= "led7",
+		.gpio		= RCAR_GP_PIN(2, 20),
+		.default_state	= LEDS_GPIO_DEFSTATE_ON,
+	}, {
+		.name		= "led6",
+		.gpio		= RCAR_GP_PIN(2, 19),
+		.default_state	= LEDS_GPIO_DEFSTATE_ON,
+	},
+};
+
+static const struct gpio_led_platform_data koelsch_leds_pdata __initconst = {
+	.leds		= koelsch_leds,
+	.num_leds	= ARRAY_SIZE(koelsch_leds),
+};
+
+/* GPIO KEY */
+#define GPIO_KEY(c, g, d, ...) \
+	{ .code = c, .gpio = g, .desc = d, .active_low = 1, \
+	  .wakeup = 1, .debounce_interval = 20 }
+
+static struct gpio_keys_button gpio_buttons[] = {
+	GPIO_KEY(KEY_4,		RCAR_GP_PIN(5, 3),	"SW2-pin4"),
+	GPIO_KEY(KEY_3,		RCAR_GP_PIN(5, 2),	"SW2-pin3"),
+	GPIO_KEY(KEY_2,		RCAR_GP_PIN(5, 1),	"SW2-pin2"),
+	GPIO_KEY(KEY_1,		RCAR_GP_PIN(5, 0),	"SW2-pin1"),
+	GPIO_KEY(KEY_G,		RCAR_GP_PIN(7, 6),	"SW36"),
+	GPIO_KEY(KEY_F,		RCAR_GP_PIN(7, 5),	"SW35"),
+	GPIO_KEY(KEY_E,		RCAR_GP_PIN(7, 4),	"SW34"),
+	GPIO_KEY(KEY_D,		RCAR_GP_PIN(7, 3),	"SW33"),
+	GPIO_KEY(KEY_C,		RCAR_GP_PIN(7, 2),	"SW32"),
+	GPIO_KEY(KEY_B,		RCAR_GP_PIN(7, 1),	"SW31"),
+	GPIO_KEY(KEY_A,		RCAR_GP_PIN(7, 0),	"SW30"),
+};
+
+static const struct gpio_keys_platform_data koelsch_keys_pdata __initconst = {
+	.buttons	= gpio_buttons,
+	.nbuttons	= ARRAY_SIZE(gpio_buttons),
+};
+
+static const struct pinctrl_map koelsch_pinctrl_map[] = {
+	/* DU */
+	PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7791", "pfc-r8a7791",
+				  "du_rgb666", "du"),
+	PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7791", "pfc-r8a7791",
+				  "du_sync", "du"),
+	PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7791", "pfc-r8a7791",
+				  "du_clk_out_0", "du"),
+	/* Ether */
+	PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
+				  "eth_link", "eth"),
+	PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
+				  "eth_mdio", "eth"),
+	PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
+				  "eth_rmii", "eth"),
+	PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
+				  "intc_irq0", "intc"),
+	/* SCIF0 (CN19: DEBUG SERIAL0) */
+	PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7791",
+				  "scif0_data_d", "scif0"),
+	/* SCIF1 (CN20: DEBUG SERIAL1) */
+	PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.7", "pfc-r8a7791",
+				  "scif1_data_d", "scif1"),
+};
+
 static void __init koelsch_add_standard_devices(void)
 {
 	r8a7791_clock_init();
+	pinctrl_register_mappings(koelsch_pinctrl_map,
+				  ARRAY_SIZE(koelsch_pinctrl_map));
+	r8a7791_pinmux_init();
 	r8a7791_add_standard_devices();
+	platform_device_register_resndata(&platform_bus, "r8a7791-ether", -1,
+					  ether_resources,
+					  ARRAY_SIZE(ether_resources),
+					  &ether_pdata, sizeof(ether_pdata));
+	platform_device_register_data(&platform_bus, "leds-gpio", -1,
+				      &koelsch_leds_pdata,
+				      sizeof(koelsch_leds_pdata));
+	platform_device_register_data(&platform_bus, "gpio-keys", -1,
+				      &koelsch_keys_pdata,
+				      sizeof(koelsch_keys_pdata));
+
+	koelsch_add_du_device();
+}
+
+/*
+ * Ether LEDs on the Koelsch board are named LINK and ACTIVE which corresponds
+ * to non-default 01 setting of the Micrel KSZ8041 PHY control register 1 bits
+ * 14-15. We have to set them back to 01 from the default 00 value each time
+ * the PHY is reset. It's also important because the PHY's LED0 signal is
+ * connected to SoC's ETH_LINK signal and in the PHY's default mode it will
+ * bounce on and off after each packet, which we apparently want to avoid.
+ */
+static int koelsch_ksz8041_fixup(struct phy_device *phydev)
+{
+	u16 phyctrl1 = phy_read(phydev, 0x1e);
+
+	phyctrl1 &= ~0xc000;
+	phyctrl1 |= 0x4000;
+	return phy_write(phydev, 0x1e, phyctrl1);
+}
+
+static void __init koelsch_init(void)
+{
+	koelsch_add_standard_devices();
+
+	if (IS_ENABLED(CONFIG_PHYLIB))
+		phy_register_fixup_for_id("r8a7791-ether-ff:01",
+					  koelsch_ksz8041_fixup);
 }
 
 static const char * const koelsch_boards_compat_dt[] __initconst = {
@@ -41,7 +228,8 @@ static const char * const koelsch_boards_compat_dt[] __initconst = {
 DT_MACHINE_START(KOELSCH_DT, "koelsch")
 	.smp		= smp_ops(r8a7791_smp_ops),
 	.init_early	= r8a7791_init_early,
-	.init_machine	= koelsch_add_standard_devices,
 	.init_time	= rcar_gen2_timer_init,
+	.init_machine	= koelsch_init,
+	.init_late	= shmobile_init_late,
 	.dt_compat	= koelsch_boards_compat_dt,
 MACHINE_END