Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

New feature development

This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.

* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  mfd/db8500-prcmu: remove support for early silicon revisions
  ARM: ux500: fix the smp_twd clock calculation
  ARM: ux500: remove support for early silicon revisions
  ARM: ux500: update register files
  ARM: ux500: register DB5500 PMU dynamically
  ARM: ux500: update ASIC detection for U5500
  ARM: ux500: support DB8520
  ARM: picoxcell: implement watchdog restart
  ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
  ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
  ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
  ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
  ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
  ARM: Orion: Remove address map info from all platform data structures
  ARM: Orion: Get address map from plat-orion instead of via platform_data
  ARM: Orion: mbus_dram_info consolidation
  ARM: Orion: Consolidate the address map setup
  ARM: Kirkwood: Add configuration for MPP12 as GPIO
  ARM: Kirkwood: Recognize A1 revision of 6282 chip
  ARM: ux500: update the MOP500 GPIO assignments
  ...

1 files changed, 56 insertions, 32 deletions

diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c
index 6826faeecc6..23be34b3bb6 100644
--- a/arch/arm/mach-ux500/board-mop500-sdi.c
+++ b/arch/arm/mach-ux500/board-mop500-sdi.c
@@ -22,6 +22,12 @@
 #include "ste-dma40-db8500.h"
 
 /*
+ * v2 has a new version of this block that need to be forced, the number found
+ * in hardware is incorrect
+ */
+#define U8500_SDI_V2_PERIPHID 0x10480180
+
+/*
  * SDI 0 (MicroSD slot)
  */
 
@@ -117,10 +123,7 @@ static void sdi0_configure(void)
 	gpio_direction_output(sdi0_en, 1);
 
 	/* Add the device, force v2 to subrevision 1 */
-	if (cpu_is_u8500v2())
-		db8500_add_sdi0(&mop500_sdi0_data, 0x10480180);
-	else
-		db8500_add_sdi0(&mop500_sdi0_data, 0);
+	db8500_add_sdi0(&mop500_sdi0_data, U8500_SDI_V2_PERIPHID);
 }
 
 void mop500_sdi_tc35892_init(void)
@@ -132,6 +135,42 @@ void mop500_sdi_tc35892_init(void)
 }
 
 /*
+ * SDI1 (SDIO WLAN)
+ */
+#ifdef CONFIG_STE_DMA40
+static struct stedma40_chan_cfg sdi1_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type = DB8500_DMA_DEV32_SD_MM1_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_WORD_WIDTH,
+	.dst_info.data_width = STEDMA40_WORD_WIDTH,
+};
+
+static struct stedma40_chan_cfg sdi1_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV32_SD_MM1_TX,
+	.src_info.data_width = STEDMA40_WORD_WIDTH,
+	.dst_info.data_width = STEDMA40_WORD_WIDTH,
+};
+#endif
+
+static struct mmci_platform_data mop500_sdi1_data = {
+	.ocr_mask	= MMC_VDD_29_30,
+	.f_max		= 50000000,
+	.capabilities	= MMC_CAP_4_BIT_DATA,
+	.gpio_cd	= -1,
+	.gpio_wp	= -1,
+#ifdef CONFIG_STE_DMA40
+	.dma_filter	= stedma40_filter,
+	.dma_rx_param	= &sdi1_dma_cfg_rx,
+	.dma_tx_param	= &sdi1_dma_cfg_tx,
+#endif
+};
+
+/*
  * SDI 2 (POP eMMC, not on DB8500ed)
  */
 
@@ -158,7 +197,8 @@ static struct stedma40_chan_cfg mop500_sdi2_dma_cfg_tx = {
 static struct mmci_platform_data mop500_sdi2_data = {
 	.ocr_mask	= MMC_VDD_165_195,
 	.f_max		= 50000000,
-	.capabilities	= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
+	.capabilities	= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA |
+			  MMC_CAP_MMC_HIGHSPEED,
 	.gpio_cd	= -1,
 	.gpio_wp	= -1,
 #ifdef CONFIG_STE_DMA40
@@ -208,20 +248,10 @@ static struct mmci_platform_data mop500_sdi4_data = {
 
 void __init mop500_sdi_init(void)
 {
-	u32 periphid = 0;
-
-	/* v2 has a new version of this block that need to be forced */
-	if (cpu_is_u8500v2())
-		periphid = 0x10480180;
-	/* PoP:ed eMMC on top of DB8500 v1.0 has problems with high speed */
-	if (!cpu_is_u8500v10())
-		mop500_sdi2_data.capabilities |= MMC_CAP_MMC_HIGHSPEED;
-
-	db8500_add_sdi2(&mop500_sdi2_data, periphid);
-
+	/* PoP:ed eMMC */
+	db8500_add_sdi2(&mop500_sdi2_data, U8500_SDI_V2_PERIPHID);
 	/* On-board eMMC */
-	db8500_add_sdi4(&mop500_sdi4_data, periphid);
-
+	db8500_add_sdi4(&mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
 	/*
 	 * On boards with the TC35892 GPIO expander, sdi0 will finally
 	 * be added when the TC35892 initializes and calls
@@ -231,13 +261,9 @@ void __init mop500_sdi_init(void)
 
 void __init snowball_sdi_init(void)
 {
-	u32 periphid = 0x10480180;
-
-	mop500_sdi2_data.capabilities |= MMC_CAP_MMC_HIGHSPEED;
-
 	/* On-board eMMC */
-	db8500_add_sdi4(&mop500_sdi4_data, periphid);
-
+	db8500_add_sdi4(&mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
+	/* External Micro SD slot */
 	mop500_sdi0_data.gpio_cd = SNOWBALL_SDMMC_CD_GPIO;
 	mop500_sdi0_data.cd_invert = true;
 	sdi0_en = SNOWBALL_SDMMC_EN_GPIO;
@@ -247,17 +273,15 @@ void __init snowball_sdi_init(void)
 
 void __init hrefv60_sdi_init(void)
 {
-	u32 periphid = 0x10480180;
-
-	mop500_sdi2_data.capabilities |= MMC_CAP_MMC_HIGHSPEED;
-
-	db8500_add_sdi2(&mop500_sdi2_data, periphid);
-
+	/* PoP:ed eMMC */
+	db8500_add_sdi2(&mop500_sdi2_data, U8500_SDI_V2_PERIPHID);
 	/* On-board eMMC */
-	db8500_add_sdi4(&mop500_sdi4_data, periphid);
-
+	db8500_add_sdi4(&mop500_sdi4_data, U8500_SDI_V2_PERIPHID);
+	/* External Micro SD slot */
 	mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO;
 	sdi0_en = HREFV60_SDMMC_EN_GPIO;
 	sdi0_vsel = HREFV60_SDMMC_1V8_3V_GPIO;
 	sdi0_configure();
+	/* WLAN SDIO channel */
+	db8500_add_sdi1(&mop500_sdi1_data, U8500_SDI_V2_PERIPHID);
 }