Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm soc-specific pinctrl changes from Olof Johansson:
 "With this, five platforms are moving to the relatively new pinctrl
  subsystem for their pin management, replacing the older soc specific
  in-kernel interfaces with common code.

  There is quite a bit of net addition of code for each platform being
  added to the pinctrl subsystem.  But the payback comes later when
  adding new boards can be done by only providing new device trees
  instead."

Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}

* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
  mtd: nand: gpmi: fix compile error caused by pinctrl call
  ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
  ARM: nomadik: enable PINCTRL_NOMADIK where needed
  ARM: mxs: enable pinctrl support
  video: mxsfb: adopt pinctrl support
  ASoC: mxs-saif: adopt pinctrl support
  i2c: mxs: adopt pinctrl support
  mtd: nand: gpmi: adopt pinctrl support
  mmc: mxs-mmc: adopt pinctrl support
  serial: mxs-auart: adopt pinctrl support
  serial: amba-pl011: adopt pinctrl support
  spi/imx: adopt pinctrl support
  i2c: imx: adopt pinctrl support
  can: flexcan: adopt pinctrl support
  net: fec: adopt pinctrl support
  ARM: ux500: switch MSP to using pinctrl for pins
  ARM: ux500: alter MSP registration to return a device pointer
  ARM: ux500: switch to using pinctrl for uart0
  ARM: ux500: delete custom pin control system
  ARM: ux500: switch over to Nomadik pinctrl driver
  ...

14 files changed, 928 insertions, 345 deletions

diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index 0e8470a3fbe..53d3d46dec1 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -9,6 +9,8 @@ config UX500_SOC_COMMON
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_764369
 	select CACHE_L2X0
+	select PINCTRL
+	select PINCTRL_NOMADIK
 
 config UX500_SOC_DB8500
 	bool
@@ -16,6 +18,7 @@ config UX500_SOC_DB8500
 	select REGULATOR
 	select REGULATOR_DB8500_PRCMU
 	select CPU_FREQ_TABLE if CPU_FREQ
+	select PINCTRL_DB8500
 
 menu "Ux500 target platform (boards)"
 
diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index fc7db5df970..041c3588598 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_MACH_MOP500)	+= board-mop500.o board-mop500-sdi.o \
 				board-mop500-regulators.o \
 				board-mop500-uib.o board-mop500-stuib.o \
 				board-mop500-u8500uib.o \
-				board-mop500-pins.o
+				board-mop500-pins.o \
+				board-mop500-msp.o
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)	+= hotplug.o
diff --git a/arch/arm/mach-ux500/board-mop500-msp.c b/arch/arm/mach-ux500/board-mop500-msp.c
new file mode 100644
index 00000000000..99604803874
--- /dev/null
+++ b/arch/arm/mach-ux500/board-mop500-msp.c
@@ -0,0 +1,267 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License terms: GNU General Public License (GPL), version 2
+ */
+
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/pinctrl/consumer.h>
+
+#include <plat/gpio-nomadik.h>
+#include <plat/pincfg.h>
+#include <plat/ste_dma40.h>
+
+#include <mach/devices.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/msp.h>
+
+#include "ste-dma40-db8500.h"
+#include "board-mop500.h"
+#include "devices-db8500.h"
+#include "pins-db8500.h"
+
+/* MSP1/3 Tx/Rx usage protection */
+static DEFINE_SPINLOCK(msp_rxtx_lock);
+
+/* Reference Count */
+static int msp_rxtx_ref;
+
+/* Pin modes */
+struct pinctrl *msp1_p;
+struct pinctrl_state *msp1_def;
+struct pinctrl_state *msp1_sleep;
+
+int msp13_i2s_init(void)
+{
+	int retval = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&msp_rxtx_lock, flags);
+	if (msp_rxtx_ref == 0 && !(IS_ERR(msp1_p) || IS_ERR(msp1_def))) {
+		retval = pinctrl_select_state(msp1_p, msp1_def);
+		if (retval)
+			pr_err("could not set MSP1 defstate\n");
+	}
+	if (!retval)
+		msp_rxtx_ref++;
+	spin_unlock_irqrestore(&msp_rxtx_lock, flags);
+
+	return retval;
+}
+
+int msp13_i2s_exit(void)
+{
+	int retval = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&msp_rxtx_lock, flags);
+	WARN_ON(!msp_rxtx_ref);
+	msp_rxtx_ref--;
+	if (msp_rxtx_ref == 0 && !(IS_ERR(msp1_p) || IS_ERR(msp1_sleep))) {
+		retval = pinctrl_select_state(msp1_p, msp1_sleep);
+		if (retval)
+			pr_err("could not set MSP1 sleepstate\n");
+	}
+	spin_unlock_irqrestore(&msp_rxtx_lock, flags);
+
+	return retval;
+}
+
+static struct stedma40_chan_cfg msp0_dma_rx = {
+	.high_priority = true,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+
+	.src_dev_type = DB8500_DMA_DEV31_MSP0_RX_SLIM0_CH0_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	/* data_width is set during configuration */
+};
+
+static struct stedma40_chan_cfg msp0_dma_tx = {
+	.high_priority = true,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+
+	.src_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV31_MSP0_TX_SLIM0_CH0_TX,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	/* data_width is set during configuration */
+};
+
+static struct msp_i2s_platform_data msp0_platform_data = {
+	.id = MSP_I2S_0,
+	.msp_i2s_dma_rx = &msp0_dma_rx,
+	.msp_i2s_dma_tx = &msp0_dma_tx,
+};
+
+static struct stedma40_chan_cfg msp1_dma_rx = {
+	.high_priority = true,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+
+	.src_dev_type = DB8500_DMA_DEV30_MSP3_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	/* data_width is set during configuration */
+};
+
+static struct stedma40_chan_cfg msp1_dma_tx = {
+	.high_priority = true,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+
+	.src_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV30_MSP1_TX,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	/* data_width is set during configuration */
+};
+
+static struct msp_i2s_platform_data msp1_platform_data = {
+	.id = MSP_I2S_1,
+	.msp_i2s_dma_rx = NULL,
+	.msp_i2s_dma_tx = &msp1_dma_tx,
+	.msp_i2s_init = msp13_i2s_init,
+	.msp_i2s_exit = msp13_i2s_exit,
+};
+
+static struct stedma40_chan_cfg msp2_dma_rx = {
+	.high_priority = true,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+
+	.src_dev_type = DB8500_DMA_DEV14_MSP2_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+
+	/* MSP2 DMA doesn't work with PSIZE == 4 on DB8500v2 */
+	.src_info.psize = STEDMA40_PSIZE_LOG_1,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_1,
+
+	/* data_width is set during configuration */
+};
+
+static struct stedma40_chan_cfg msp2_dma_tx = {
+	.high_priority = true,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+
+	.src_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV14_MSP2_TX,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	.use_fixed_channel = true,
+	.phy_channel = 1,
+
+	/* data_width is set during configuration */
+};
+
+static struct platform_device *db8500_add_msp_i2s(struct device *parent,
+			int id,
+			resource_size_t base, int irq,
+			struct msp_i2s_platform_data *pdata)
+{
+	struct platform_device *pdev;
+	struct resource res[] = {
+		DEFINE_RES_MEM(base, SZ_4K),
+		DEFINE_RES_IRQ(irq),
+	};
+
+	pr_info("Register platform-device 'ux500-msp-i2s', id %d, irq %d\n",
+		id, irq);
+	pdev = platform_device_register_resndata(parent, "ux500-msp-i2s", id,
+						res, ARRAY_SIZE(res),
+						pdata, sizeof(*pdata));
+	if (!pdev) {
+		pr_err("Failed to register platform-device 'ux500-msp-i2s.%d'!\n",
+			id);
+		return NULL;
+	}
+
+	return pdev;
+}
+
+/* Platform device for ASoC U8500 machine */
+static struct platform_device snd_soc_u8500 = {
+		.name = "snd-soc-u8500",
+		.id = 0,
+		.dev = {
+			.platform_data = NULL,
+		},
+};
+
+/* Platform device for Ux500-PCM */
+static struct platform_device ux500_pcm = {
+		.name = "ux500-pcm",
+		.id = 0,
+		.dev = {
+			.platform_data = NULL,
+		},
+};
+
+static struct msp_i2s_platform_data msp2_platform_data = {
+	.id = MSP_I2S_2,
+	.msp_i2s_dma_rx = &msp2_dma_rx,
+	.msp_i2s_dma_tx = &msp2_dma_tx,
+};
+
+static struct msp_i2s_platform_data msp3_platform_data = {
+	.id		= MSP_I2S_3,
+	.msp_i2s_dma_rx	= &msp1_dma_rx,
+	.msp_i2s_dma_tx	= NULL,
+	.msp_i2s_init = msp13_i2s_init,
+	.msp_i2s_exit = msp13_i2s_exit,
+};
+
+int mop500_msp_init(struct device *parent)
+{
+	struct platform_device *msp1;
+
+	pr_info("%s: Register platform-device 'snd-soc-u8500'.\n", __func__);
+	platform_device_register(&snd_soc_u8500);
+
+	pr_info("Initialize MSP I2S-devices.\n");
+	db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0,
+			   &msp0_platform_data);
+	msp1 = db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1,
+			   &msp1_platform_data);
+	db8500_add_msp_i2s(parent, 2, U8500_MSP2_BASE, IRQ_DB8500_MSP2,
+			   &msp2_platform_data);
+	db8500_add_msp_i2s(parent, 3, U8500_MSP3_BASE, IRQ_DB8500_MSP1,
+			   &msp3_platform_data);
+
+	/* Get the pinctrl handle for MSP1 */
+	if (msp1) {
+		msp1_p = pinctrl_get(&msp1->dev);
+		if (IS_ERR(msp1_p))
+			dev_err(&msp1->dev, "could not get MSP1 pinctrl\n");
+		else {
+			msp1_def = pinctrl_lookup_state(msp1_p,
+							PINCTRL_STATE_DEFAULT);
+			if (IS_ERR(msp1_def)) {
+				dev_err(&msp1->dev,
+					"could not get MSP1 defstate\n");
+			}
+			msp1_sleep = pinctrl_lookup_state(msp1_p,
+							  PINCTRL_STATE_SLEEP);
+			if (IS_ERR(msp1_sleep))
+				dev_err(&msp1->dev,
+					"could not get MSP1 idlestate\n");
+		}
+	}
+
+	pr_info("%s: Register platform-device 'ux500-pcm'\n", __func__);
+	platform_device_register(&ux500_pcm);
+
+	return 0;
+}
diff --git a/arch/arm/mach-ux500/board-mop500-msp.h b/arch/arm/mach-ux500/board-mop500-msp.h
new file mode 100644
index 00000000000..6fcfb5e2cc9
--- /dev/null
+++ b/arch/arm/mach-ux500/board-mop500-msp.h
@@ -0,0 +1,14 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2012
+ *
+ * Author: Ola Lilja <ola.o.lilja@stericsson.com>,
+ *         for ST-Ericsson.
+ *
+ * License terms:
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+void mop500_msp_init(struct device *parent);
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index f5413dca532..32fd9920446 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -7,299 +7,508 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/bug.h>
+#include <linux/string.h>
+#include <linux/pinctrl/machine.h>
 
 #include <asm/mach-types.h>
 #include <plat/pincfg.h>
 #include <plat/gpio-nomadik.h>
+
 #include <mach/hardware.h>
 
 #include "pins-db8500.h"
+#include "board-mop500.h"
 
-static pin_cfg_t mop500_pins_common[] = {
-	/* I2C */
-	GPIO147_I2C0_SCL,
-	GPIO148_I2C0_SDA,
-	GPIO16_I2C1_SCL,
-	GPIO17_I2C1_SDA,
-	GPIO10_I2C2_SDA,
-	GPIO11_I2C2_SCL,
-	GPIO229_I2C3_SDA,
-	GPIO230_I2C3_SCL,
-
-	/* MSP0 */
-	GPIO12_MSP0_TXD,
-	GPIO13_MSP0_TFS,
-	GPIO14_MSP0_TCK,
-	GPIO15_MSP0_RXD,
-
-	/* MSP2: HDMI */
-	GPIO193_MSP2_TXD,
-	GPIO194_MSP2_TCK,
-	GPIO195_MSP2_TFS,
-	GPIO196_MSP2_RXD | PIN_OUTPUT_LOW,
-
-	/* Touch screen INTERFACE */
-	GPIO84_GPIO	| PIN_INPUT_PULLUP, /* TOUCH_INT1 */
-
-	/* STMPE1601/tc35893 keypad  IRQ */
-	GPIO218_GPIO	| PIN_INPUT_PULLUP,
-
-	/* MMC0 (MicroSD card) */
-	GPIO18_MC0_CMDDIR	| PIN_OUTPUT_HIGH,
-	GPIO19_MC0_DAT0DIR	| PIN_OUTPUT_HIGH,
-	GPIO20_MC0_DAT2DIR	| PIN_OUTPUT_HIGH,
-
-	GPIO22_MC0_FBCLK	| PIN_INPUT_NOPULL,
-	GPIO23_MC0_CLK		| PIN_OUTPUT_LOW,
-	GPIO24_MC0_CMD		| PIN_INPUT_PULLUP,
-	GPIO25_MC0_DAT0		| PIN_INPUT_PULLUP,
-	GPIO26_MC0_DAT1		| PIN_INPUT_PULLUP,
-	GPIO27_MC0_DAT2		| PIN_INPUT_PULLUP,
-	GPIO28_MC0_DAT3		| PIN_INPUT_PULLUP,
-
-	/* SDI1 (SDIO) */
-	GPIO208_MC1_CLK		| PIN_OUTPUT_LOW,
-	GPIO209_MC1_FBCLK	| PIN_INPUT_NOPULL,
-	GPIO210_MC1_CMD		| PIN_INPUT_PULLUP,
-	GPIO211_MC1_DAT0	| PIN_INPUT_PULLUP,
-	GPIO212_MC1_DAT1	| PIN_INPUT_PULLUP,
-	GPIO213_MC1_DAT2	| PIN_INPUT_PULLUP,
-	GPIO214_MC1_DAT3	| PIN_INPUT_PULLUP,
-
-	/* MMC2 (On-board DATA INTERFACE eMMC) */
-	GPIO128_MC2_CLK		| PIN_OUTPUT_LOW,
-	GPIO129_MC2_CMD		| PIN_INPUT_PULLUP,
-	GPIO130_MC2_FBCLK	| PIN_INPUT_NOPULL,
-	GPIO131_MC2_DAT0	| PIN_INPUT_PULLUP,
-	GPIO132_MC2_DAT1	| PIN_INPUT_PULLUP,
-	GPIO133_MC2_DAT2	| PIN_INPUT_PULLUP,
-	GPIO134_MC2_DAT3	| PIN_INPUT_PULLUP,
-	GPIO135_MC2_DAT4	| PIN_INPUT_PULLUP,
-	GPIO136_MC2_DAT5	| PIN_INPUT_PULLUP,
-	GPIO137_MC2_DAT6	| PIN_INPUT_PULLUP,
-	GPIO138_MC2_DAT7	| PIN_INPUT_PULLUP,
-
-	/* MMC4 (On-board STORAGE INTERFACE eMMC) */
-	GPIO197_MC4_DAT3	| PIN_INPUT_PULLUP,
-	GPIO198_MC4_DAT2	| PIN_INPUT_PULLUP,
-	GPIO199_MC4_DAT1	| PIN_INPUT_PULLUP,
-	GPIO200_MC4_DAT0	| PIN_INPUT_PULLUP,
-	GPIO201_MC4_CMD		| PIN_INPUT_PULLUP,
-	GPIO202_MC4_FBCLK	| PIN_INPUT_NOPULL,
-	GPIO203_MC4_CLK		| PIN_OUTPUT_LOW,
-	GPIO204_MC4_DAT7	| PIN_INPUT_PULLUP,
-	GPIO205_MC4_DAT6	| PIN_INPUT_PULLUP,
-	GPIO206_MC4_DAT5	| PIN_INPUT_PULLUP,
-	GPIO207_MC4_DAT4	| PIN_INPUT_PULLUP,
-
-	/* SKE keypad */
-	GPIO153_KP_I7,
-	GPIO154_KP_I6,
-	GPIO155_KP_I5,
-	GPIO156_KP_I4,
-	GPIO157_KP_O7,
-	GPIO158_KP_O6,
-	GPIO159_KP_O5,
-	GPIO160_KP_O4,
-	GPIO161_KP_I3,
-	GPIO162_KP_I2,
-	GPIO163_KP_I1,
-	GPIO164_KP_I0,
-	GPIO165_KP_O3,
-	GPIO166_KP_O2,
-	GPIO167_KP_O1,
-	GPIO168_KP_O0,
+enum custom_pin_cfg_t {
+	PINS_FOR_DEFAULT,
+	PINS_FOR_U9500,
+};
 
-	/* UART */
-	/* uart-0 pins gpio configuration should be
-	 * kept intact to prevent glitch in tx line
-	 * when tty dev is opened. Later these pins
+static enum custom_pin_cfg_t pinsfor;
+
+/* These simply sets bias for pins */
+#define BIAS(a,b) static unsigned long a[] = { b }
+
+BIAS(pd, PIN_PULL_DOWN);
+BIAS(slpm_gpio_nopull, PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
+BIAS(in_nopull, PIN_INPUT_NOPULL);
+BIAS(in_nopull_sleep_nowkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_DISABLE);
+BIAS(in_pu, PIN_INPUT_PULLUP);
+BIAS(in_pd, PIN_INPUT_PULLDOWN);
+BIAS(in_pd_slpm_in_pu, PIN_INPUT_PULLDOWN|PIN_SLPM_INPUT_PULLUP);
+BIAS(in_pu_slpm_out_lo, PIN_INPUT_PULLUP|PIN_SLPM_OUTPUT_LOW);
+BIAS(out_hi, PIN_OUTPUT_HIGH);
+BIAS(out_lo, PIN_OUTPUT_LOW);
+BIAS(out_lo_sleep_nowkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE);
+/* These also force them into GPIO mode */
+BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
+BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED);
+BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
+BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
+BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
+BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
+/* Sleep modes */
+BIAS(sleep_in_wkup_pdis, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
+BIAS(sleep_in_nopull_wkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE);
+BIAS(sleep_out_hi_wkup_pdis, PIN_SLPM_OUTPUT_HIGH|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
+BIAS(sleep_out_lo_wkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE);
+BIAS(sleep_out_wkup_pdis, PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
+
+/* We use these to define hog settings that are always done on boot */
+#define DB8500_MUX_HOG(group,func) \
+	PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-db8500", group, func)
+#define DB8500_PIN_HOG(pin,conf) \
+	PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-db8500", pin, conf)
+
+/* These are default states associated with device and changed runtime */
+#define DB8500_MUX(group,func,dev) \
+	PIN_MAP_MUX_GROUP_DEFAULT(dev, "pinctrl-db8500", group, func)
+#define DB8500_PIN(pin,conf,dev) \
+	PIN_MAP_CONFIGS_PIN_DEFAULT(dev, "pinctrl-db8500", pin, conf)
+
+#define DB8500_PIN_SLEEP(pin,conf,dev) \
+	PIN_MAP_CONFIGS_PIN(dev, PINCTRL_STATE_SLEEP, "pinctrl-db8500",	\
+			    pin, conf)
+
+/* Pin control settings */
+static struct pinctrl_map __initdata mop500_family_pinmap[] = {
+	/*
+	 * uMSP0, mux in 4 pins, regular placement of RX/TX
+	 * explicitly set the pins to no pull
+	 */
+	DB8500_MUX_HOG("msp0txrx_a_1", "msp0"),
+	DB8500_MUX_HOG("msp0tfstck_a_1", "msp0"),
+	DB8500_PIN_HOG("GPIO12_AC4", in_nopull), /* TXD */
+	DB8500_PIN_HOG("GPIO15_AC3", in_nopull), /* RXD */
+	DB8500_PIN_HOG("GPIO13_AF3", in_nopull), /* TFS */
+	DB8500_PIN_HOG("GPIO14_AE3", in_nopull), /* TCK */
+	/* MSP2 for HDMI, pull down TXD, TCK, TFS  */
+	DB8500_MUX_HOG("msp2_a_1", "msp2"),
+	DB8500_PIN_HOG("GPIO193_AH27", in_pd), /* TXD */
+	DB8500_PIN_HOG("GPIO194_AF27", in_pd), /* TCK */
+	DB8500_PIN_HOG("GPIO195_AG28", in_pd), /* TFS */
+	DB8500_PIN_HOG("GPIO196_AG26", out_lo), /* RXD */
+	/*
+	 * LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to
+	 * pull-up
+	 * TODO: is this really correct? Snowball doesn't have a LCD.
+	 */
+	DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
+	DB8500_PIN_HOG("GPIO68_E1", in_pu),
+	DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
+	/*
+	 * STMPE1601/tc35893 keypad IRQ GPIO 218
+	 * TODO: set for snowball and HREF really??
+	 */
+	DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
+	/*
+	 * UART0, we do not mux in u0 here.
+	 * uart-0 pins gpio configuration should be kept intact to prevent
+	 * a glitch in tx line when the tty dev is opened. Later these pins
 	 * are configured to uart mop500_pins_uart0
-	 *
-	 * It will be replaced with uart configuration
-	 * once the issue is solved.
 	 */
-	GPIO0_GPIO	| PIN_INPUT_PULLUP,
-	GPIO1_GPIO	| PIN_OUTPUT_HIGH,
-	GPIO2_GPIO	| PIN_INPUT_PULLUP,
-	GPIO3_GPIO	| PIN_OUTPUT_HIGH,
-
-	GPIO29_U2_RXD	| PIN_INPUT_PULLUP,
-	GPIO30_U2_TXD	| PIN_OUTPUT_HIGH,
-	GPIO31_U2_CTSn	| PIN_INPUT_PULLUP,
-	GPIO32_U2_RTSn	| PIN_OUTPUT_HIGH,
-
-	/* Display & HDMI HW sync */
-	GPIO68_LCD_VSI0	| PIN_INPUT_PULLUP,
-	GPIO69_LCD_VSI1	| PIN_INPUT_PULLUP,
+	DB8500_PIN_HOG("GPIO0_AJ5", in_pu), /* CTS */
+	DB8500_PIN_HOG("GPIO1_AJ3", out_hi), /* RTS */
+	DB8500_PIN_HOG("GPIO2_AH4", in_pu), /* RXD */
+	DB8500_PIN_HOG("GPIO3_AH3", out_hi), /* TXD */
+	/*
+	 * Mux in UART2 on altfunction C and set pull-ups.
+	 * TODO: is this used on U8500 variants and Snowball really?
+	 * The setting on GPIO31 conflicts with magnetometer use on hrefv60
+	 */
+	DB8500_MUX_HOG("u2rxtx_c_1", "u2"),
+	DB8500_MUX_HOG("u2ctsrts_c_1", "u2"),
+	DB8500_PIN_HOG("GPIO29_W2", in_pu), /* RXD */
+	DB8500_PIN_HOG("GPIO30_W3", out_hi), /* TXD */
+	DB8500_PIN_HOG("GPIO31_V3", in_pu), /* CTS */
+	DB8500_PIN_HOG("GPIO32_V2", out_hi), /* RTS */
+	/*
+	 * The following pin sets were known as "runtime pins" before being
+	 * converted to the pinctrl model. Here we model them as "default"
+	 * states.
+	 */
+	/* Mux in UART0 after initialization */
+	DB8500_MUX("u0_a_1", "u0", "uart0"),
+	DB8500_PIN("GPIO0_AJ5", in_pu, "uart0"), /* CTS */
+	DB8500_PIN("GPIO1_AJ3", out_hi, "uart0"), /* RTS */
+	DB8500_PIN("GPIO2_AH4", in_pu, "uart0"), /* RXD */
+	DB8500_PIN("GPIO3_AH3", out_hi, "uart0"), /* TXD */
+	/* UART0 sleep state */
+	DB8500_PIN_SLEEP("GPIO0_AJ5", sleep_in_wkup_pdis, "uart0"),
+	DB8500_PIN_SLEEP("GPIO1_AJ3", sleep_out_hi_wkup_pdis, "uart0"),
+	DB8500_PIN_SLEEP("GPIO2_AH4", sleep_in_wkup_pdis, "uart0"),
+	DB8500_PIN_SLEEP("GPIO3_AH3", sleep_out_wkup_pdis, "uart0"),
+	/* MSP1 for ALSA codec */
+	DB8500_MUX("msp1txrx_a_1", "msp1", "ux500-msp-i2s.1"),
+	DB8500_MUX("msp1_a_1", "msp1", "ux500-msp-i2s.1"),
+	DB8500_PIN("GPIO33_AF2", out_lo_sleep_nowkup, "ux500-msp-i2s.1"),
+	DB8500_PIN("GPIO34_AE1", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+	DB8500_PIN("GPIO35_AE2", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+	DB8500_PIN("GPIO36_AG2", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+	/* MSP1 sleep state */
+	DB8500_PIN_SLEEP("GPIO33_AF2", sleep_out_lo_wkup, "ux500-msp-i2s.1"),
+	DB8500_PIN_SLEEP("GPIO34_AE1", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
+	DB8500_PIN_SLEEP("GPIO35_AE2", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
+	DB8500_PIN_SLEEP("GPIO36_AG2", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
+	/* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
+	DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
+	DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
+	/* Mux in LCD VSI1 and pull it up for MCDE HDMI output */
+	DB8500_MUX("lcdvsi1_a_1", "lcd", "av8100-hdmi"),
+	/* Mux in I2C blocks, put pins into GPIO in sleepmode no pull-up */
+	DB8500_MUX("i2c0_a_1", "i2c0", "nmk-i2c.0"),
+	DB8500_PIN("GPIO147_C15", slpm_gpio_nopull, "nmk-i2c.0"),
+	DB8500_PIN("GPIO148_B16", slpm_gpio_nopull, "nmk-i2c.0"),
+	DB8500_MUX("i2c1_b_2", "i2c1", "nmk-i2c.1"),
+	DB8500_PIN("GPIO16_AD3", slpm_gpio_nopull, "nmk-i2c.1"),
+	DB8500_PIN("GPIO17_AD4", slpm_gpio_nopull, "nmk-i2c.1"),
+	DB8500_MUX("i2c2_b_2", "i2c2", "nmk-i2c.2"),
+	DB8500_PIN("GPIO10_AF5", slpm_gpio_nopull, "nmk-i2c.2"),
+	DB8500_PIN("GPIO11_AG4", slpm_gpio_nopull, "nmk-i2c.2"),
+	DB8500_MUX("i2c3_c_2", "i2c3", "nmk-i2c.3"),
+	DB8500_PIN("GPIO229_AG7", slpm_gpio_nopull, "nmk-i2c.3"),
+	DB8500_PIN("GPIO230_AF7", slpm_gpio_nopull, "nmk-i2c.3"),
+	/* Mux in SDI0 (here called MC0) used for removable MMC/SD/SDIO cards */
+	DB8500_MUX("mc0_a_1", "mc0", "sdi0"),
+	DB8500_PIN("GPIO18_AC2", out_hi, "sdi0"), /* CMDDIR */
+	DB8500_PIN("GPIO19_AC1", out_hi, "sdi0"), /* DAT0DIR */
+	DB8500_PIN("GPIO20_AB4", out_hi, "sdi0"), /* DAT2DIR */
+	DB8500_PIN("GPIO22_AA3", in_nopull, "sdi0"), /* FBCLK */
+	DB8500_PIN("GPIO23_AA4", out_lo, "sdi0"), /* CLK */
+	DB8500_PIN("GPIO24_AB2", in_pu, "sdi0"), /* CMD */
+	DB8500_PIN("GPIO25_Y4", in_pu, "sdi0"), /* DAT0 */
+	DB8500_PIN("GPIO26_Y2", in_pu, "sdi0"), /* DAT1 */
+	DB8500_PIN("GPIO27_AA2", in_pu, "sdi0"), /* DAT2 */
+	DB8500_PIN("GPIO28_AA1", in_pu, "sdi0"), /* DAT3 */
+	/* Mux in SDI1 (here called MC1) used for SDIO for CW1200 WLAN */
+	DB8500_MUX("mc1_a_1", "mc1", "sdi1"),
+	DB8500_PIN("GPIO208_AH16", out_lo, "sdi1"), /* CLK */
+	DB8500_PIN("GPIO209_AG15", in_nopull, "sdi1"), /* FBCLK */
+	DB8500_PIN("GPIO210_AJ15", in_pu, "sdi1"), /* CMD */
+	DB8500_PIN("GPIO211_AG14", in_pu, "sdi1"), /* DAT0 */
+	DB8500_PIN("GPIO212_AF13", in_pu, "sdi1"), /* DAT1 */
+	DB8500_PIN("GPIO213_AG13", in_pu, "sdi1"), /* DAT2 */
+	DB8500_PIN("GPIO214_AH15", in_pu, "sdi1"), /* DAT3 */
+	/* Mux in SDI2 (here called MC2) used for for PoP eMMC */
+	DB8500_MUX("mc2_a_1", "mc2", "sdi2"),
+	DB8500_PIN("GPIO128_A5", out_lo, "sdi2"), /* CLK */
+	DB8500_PIN("GPIO129_B4", in_pu, "sdi2"), /* CMD */
+	DB8500_PIN("GPIO130_C8", in_nopull, "sdi2"), /* FBCLK */
+	DB8500_PIN("GPIO131_A12", in_pu, "sdi2"), /* DAT0 */
+	DB8500_PIN("GPIO132_C10", in_pu, "sdi2"), /* DAT1 */
+	DB8500_PIN("GPIO133_B10", in_pu, "sdi2"), /* DAT2 */
+	DB8500_PIN("GPIO134_B9", in_pu, "sdi2"), /* DAT3 */
+	DB8500_PIN("GPIO135_A9", in_pu, "sdi2"), /* DAT4 */
+	DB8500_PIN("GPIO136_C7", in_pu, "sdi2"), /* DAT5 */
+	DB8500_PIN("GPIO137_A7", in_pu, "sdi2"), /* DAT6 */
+	DB8500_PIN("GPIO138_C5", in_pu, "sdi2"), /* DAT7 */
+	/* Mux in SDI4 (here called MC4) used for for PCB-mounted eMMC */
+	DB8500_MUX("mc4_a_1", "mc4", "sdi4"),
+	DB8500_PIN("GPIO197_AH24", in_pu, "sdi4"), /* DAT3 */
+	DB8500_PIN("GPIO198_AG25", in_pu, "sdi4"), /* DAT2 */
+	DB8500_PIN("GPIO199_AH23", in_pu, "sdi4"), /* DAT1 */
+	DB8500_PIN("GPIO200_AH26", in_pu, "sdi4"), /* DAT0 */
+	DB8500_PIN("GPIO201_AF24", in_pu, "sdi4"), /* CMD */
+	DB8500_PIN("GPIO202_AF25", in_nopull, "sdi4"), /* FBCLK */
+	DB8500_PIN("GPIO203_AE23", out_lo, "sdi4"), /* CLK */
+	DB8500_PIN("GPIO204_AF23", in_pu, "sdi4"), /* DAT7 */
+	DB8500_PIN("GPIO205_AG23", in_pu, "sdi4"), /* DAT6 */
+	DB8500_PIN("GPIO206_AG24", in_pu, "sdi4"), /* DAT5 */
+	DB8500_PIN("GPIO207_AJ23", in_pu, "sdi4"), /* DAT4 */
+	/* Mux in USB pins, drive STP high */
+	DB8500_MUX("usb_a_1", "usb", "musb-ux500.0"),
+	DB8500_PIN("GPIO257_AE29", out_hi, "musb-ux500.0"), /* STP */
+	/* Mux in SPI2 pins on the "other C1" altfunction */
+	DB8500_MUX("spi2_oc1_1", "spi2", "spi2"),
+	DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */
+	DB8500_PIN("GPIO218_AH11", in_pd, "spi2"), /* RXD */
+	DB8500_PIN("GPIO215_AH13", out_lo, "spi2"), /* TXD */
+	DB8500_PIN("GPIO217_AH12", out_lo, "spi2"), /* CLK */
 };
 
-static pin_cfg_t mop500_pins_default[] = {
-	/* SSP0 */
-	GPIO143_SSP0_CLK,
-	GPIO144_SSP0_FRM,
-	GPIO145_SSP0_RXD | PIN_PULL_DOWN,
-	GPIO146_SSP0_TXD,
-
-
-	GPIO217_GPIO	| PIN_INPUT_PULLUP, /* TC35892 IRQ */
-
-	/* SDI0 (MicroSD card) */
-	GPIO21_MC0_DAT31DIR	| PIN_OUTPUT_HIGH,
-
-	/* UART */
-	GPIO4_U1_RXD	| PIN_INPUT_PULLUP,
-	GPIO5_U1_TXD	| PIN_OUTPUT_HIGH,
-	GPIO6_U1_CTSn	| PIN_INPUT_PULLUP,
-	GPIO7_U1_RTSn	| PIN_OUTPUT_HIGH,
+/*
+ * These are specifically for the MOP500 and HREFP (pre-v60) version of the
+ * board, which utilized a TC35892 GPIO expander instead of using a lot of
+ * on-chip pins as the HREFv60 and later does.
+ */
+static struct pinctrl_map __initdata mop500_pinmap[] = {
+	/* Mux in SSP0, pull down RXD pin */
+	DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
+	DB8500_PIN_HOG("GPIO145_C13", pd),
+	/*
+	 * XENON Flashgun on image processor GPIO (controlled from image
+	 * processor firmware), mux in these image processor GPIO lines 0
+	 * (XENON_FLASH_ID) and 1 (XENON_READY) on altfunction C and pull up
+	 * the pins.
+	 */
+	DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
+	DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
+	DB8500_PIN_HOG("GPIO6_AF6", in_pu),
+	DB8500_PIN_HOG("GPIO7_AG5", in_pu),
+	/* TC35892 IRQ, pull up the line, let the driver mux in the pin */
+	DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu),
+	/* Mux in UART1 and set the pull-ups */
+	DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
+	DB8500_MUX_HOG("u1ctsrts_a_1", "u1"),
+	DB8500_PIN_HOG("GPIO4_AH6", in_pu), /* RXD */
+	DB8500_PIN_HOG("GPIO5_AG6", out_hi), /* TXD */
+	DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* CTS */
+	DB8500_PIN_HOG("GPIO7_AG5", out_hi), /* RTS */
+	/*
+	 * Runtime stuff: make it possible to mux in the SKE keypad
+	 * and bias the pins
+	 */
+	DB8500_MUX("kp_a_2", "kp", "ske"),
+	DB8500_PIN("GPIO153_B17", in_pd_slpm_in_pu, "ske"), /* I7 */
+	DB8500_PIN("GPIO154_C16", in_pd_slpm_in_pu, "ske"), /* I6 */
+	DB8500_PIN("GPIO155_C19", in_pd_slpm_in_pu, "ske"), /* I5 */
+	DB8500_PIN("GPIO156_C17", in_pd_slpm_in_pu, "ske"), /* I4 */
+	DB8500_PIN("GPIO161_D21", in_pd_slpm_in_pu, "ske"), /* I3 */
+	DB8500_PIN("GPIO162_D20", in_pd_slpm_in_pu, "ske"), /* I2 */
+	DB8500_PIN("GPIO163_C20", in_pd_slpm_in_pu, "ske"), /* I1 */
+	DB8500_PIN("GPIO164_B21", in_pd_slpm_in_pu, "ske"), /* I0 */
+	DB8500_PIN("GPIO157_A18", in_pu_slpm_out_lo, "ske"), /* O7 */
+	DB8500_PIN("GPIO158_C18", in_pu_slpm_out_lo, "ske"), /* O6 */
+	DB8500_PIN("GPIO159_B19", in_pu_slpm_out_lo, "ske"), /* O5 */
+	DB8500_PIN("GPIO160_B20", in_pu_slpm_out_lo, "ske"), /* O4 */
+	DB8500_PIN("GPIO165_C21", in_pu_slpm_out_lo, "ske"), /* O3 */
+	DB8500_PIN("GPIO166_A22", in_pu_slpm_out_lo, "ske"), /* O2 */
+	DB8500_PIN("GPIO167_B24", in_pu_slpm_out_lo, "ske"), /* O1 */
+	DB8500_PIN("GPIO168_C22", in_pu_slpm_out_lo, "ske"), /* O0 */
+	/* Mux in and drive the SDI0 DAT31DIR line high at runtime */
+	DB8500_MUX("mc0dat31dir_a_1", "mc0", "sdi0"),
+	DB8500_PIN("GPIO21_AB3", out_hi, "sdi0"),
 };
 
-static pin_cfg_t hrefv60_pins[] = {
-	/* WLAN */
-	GPIO4_GPIO		| PIN_INPUT_PULLUP,/* WLAN_IRQ */
-	GPIO85_GPIO		| PIN_OUTPUT_LOW,/* WLAN_ENA */
-
-	/* XENON Flashgun INTERFACE */
-	GPIO6_IP_GPIO0	| PIN_INPUT_PULLUP,/* XENON_FLASH_ID */
-	GPIO7_IP_GPIO1	| PIN_INPUT_PULLUP,/* XENON_READY */
-	GPIO170_GPIO	| PIN_OUTPUT_LOW, /* XENON_CHARGE */
-
-	/* Assistant LED INTERFACE */
-	GPIO21_GPIO | PIN_OUTPUT_LOW,  /* XENON_EN1 */
-	GPIO64_IP_GPIO4 | PIN_OUTPUT_LOW,  /* XENON_EN2 */
-
-	/* Magnetometer */
-	GPIO31_GPIO | PIN_INPUT_PULLUP,  /* magnetometer_INT */
-	GPIO32_GPIO | PIN_INPUT_PULLDOWN, /* Magnetometer DRDY */
-
-	/* Display Interface */
-	GPIO65_GPIO		| PIN_OUTPUT_LOW, /* DISP1 RST */
-	GPIO66_GPIO		| PIN_OUTPUT_LOW, /* DISP2 RST */
-
-	/* Touch screen INTERFACE */
-	GPIO143_GPIO	| PIN_OUTPUT_LOW,/*TOUCH_RST1 */
-
-	/* Touch screen INTERFACE 2 */
-	GPIO67_GPIO	| PIN_INPUT_PULLUP, /* TOUCH_INT2 */
-	GPIO146_GPIO	| PIN_OUTPUT_LOW,/*TOUCH_RST2 */
-
-	/* ETM_PTM_TRACE INTERFACE */
-	GPIO70_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA23 */
-	GPIO71_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA22 */
-	GPIO72_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA21 */
-	GPIO73_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA20 */
-	GPIO74_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA19 */
-
-	/* NAHJ INTERFACE */
-	GPIO76_GPIO	| PIN_OUTPUT_LOW,/* NAHJ_CTRL */
-	GPIO216_GPIO	| PIN_OUTPUT_HIGH,/* NAHJ_CTRL_INV */
-
-	/* NFC INTERFACE */
-	GPIO77_GPIO	| PIN_OUTPUT_LOW, /* NFC_ENA */
-	GPIO144_GPIO	| PIN_INPUT_PULLDOWN, /* NFC_IRQ */
-	GPIO142_GPIO	| PIN_OUTPUT_LOW, /* NFC_RESET */
-
-	/* Keyboard MATRIX INTERFACE */
-	GPIO90_MC5_CMD	| PIN_OUTPUT_LOW, /* KP_O_1 */
-	GPIO87_MC5_DAT1	| PIN_OUTPUT_LOW, /* KP_O_2 */
-	GPIO86_MC5_DAT0	| PIN_OUTPUT_LOW, /* KP_O_3 */
-	GPIO96_KP_O6	| PIN_OUTPUT_LOW, /* KP_O_6 */
-	GPIO94_KP_O7	| PIN_OUTPUT_LOW, /* KP_O_7 */
-	GPIO93_MC5_DAT4	| PIN_INPUT_PULLUP, /* KP_I_0 */
-	GPIO89_MC5_DAT3	| PIN_INPUT_PULLUP, /* KP_I_2 */
-	GPIO88_MC5_DAT2	| PIN_INPUT_PULLUP, /* KP_I_3 */
-	GPIO91_GPIO	| PIN_INPUT_PULLUP, /* FORCE_SENSING_INT */
-	GPIO92_GPIO	| PIN_OUTPUT_LOW, /* FORCE_SENSING_RST */
-	GPIO97_GPIO	| PIN_OUTPUT_LOW, /* FORCE_SENSING_WU */
-
-	/* DiPro Sensor Interface */
-	GPIO139_GPIO	| PIN_INPUT_PULLUP, /* DIPRO_INT */
-
-	/* HAL SWITCH INTERFACE */
-	GPIO145_GPIO	| PIN_INPUT_PULLDOWN,/* HAL_SW */
-
-	/* Audio Amplifier Interface */
-	GPIO149_GPIO	| PIN_OUTPUT_LOW, /* VAUDIO_HF_EN */
-
-	/* GBF INTERFACE */
-	GPIO171_GPIO	| PIN_OUTPUT_LOW, /* GBF_ENA_RESET */
-
-	/* MSP : HDTV INTERFACE */
-	GPIO192_GPIO	| PIN_INPUT_PULLDOWN,
-
-	/* ACCELEROMETER_INTERFACE */
-	GPIO82_GPIO		| PIN_INPUT_PULLUP, /* ACC_INT1 */
-	GPIO83_GPIO		| PIN_INPUT_PULLUP, /* ACC_INT2 */
-
-	/* Proximity Sensor */
-	GPIO217_GPIO		| PIN_INPUT_PULLUP,
-
-
+/*
+ * The HREFv60 series of platforms is using available pins on the DB8500
+ * insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0
+ * and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
+ */
+static struct pinctrl_map __initdata hrefv60_pinmap[] = {
+	/* Drive WLAN_ENA low */
+	DB8500_PIN_HOG("GPIO85_D5", gpio_out_lo), /* WLAN_ENA */
+	/*
+	 * XENON Flashgun on image processor GPIO (controlled from image
+	 * processor firmware), mux in these image processor GPIO lines 0
+	 * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+	 * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+	 * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+	 */
+	DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
+	DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
+	DB8500_MUX_HOG("ipgpio4_c_1", "ipgpio"),
+	DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* XENON_FLASH_ID */
+	DB8500_PIN_HOG("GPIO7_AG5", in_pu), /* XENON_READY */
+	DB8500_PIN_HOG("GPIO21_AB3", gpio_out_lo), /* XENON_EN1 */
+	DB8500_PIN_HOG("GPIO64_F3", out_lo), /* XENON_EN2 */
+	/* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
+	DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
+	DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
+	/*
+	 * Display Interface 1 uses GPIO 65 for RST (reset).
+	 * Display Interface 2 uses GPIO 66 for RST (reset).
+	 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+	 */
+	DB8500_PIN_HOG("GPIO65_F1", gpio_out_hi), /* DISP1 NO RST */
+	DB8500_PIN_HOG("GPIO66_G3", gpio_out_lo), /* DISP2 RST */
+	/*
+	 * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
+	 * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
+	 * reset signals low.
+	 */
+	DB8500_PIN_HOG("GPIO143_D12", gpio_out_lo), /* TOUCH_RST1 */
+	DB8500_PIN_HOG("GPIO67_G2", gpio_in_pu), /* TOUCH_INT2 */
+	DB8500_PIN_HOG("GPIO146_D13", gpio_out_lo), /* TOUCH_RST2 */
+	/*
+	 * Drive D19-D23 for the ETM PTM trace interface low,
+	 * (presumably pins are unconnected therefore grounded here,
+	 * the "other alt C1" setting enables these pins)
+	 */
+	DB8500_PIN_HOG("GPIO70_G5", gpio_out_lo),
+	DB8500_PIN_HOG("GPIO71_G4", gpio_out_lo),
+	DB8500_PIN_HOG("GPIO72_H4", gpio_out_lo),
+	DB8500_PIN_HOG("GPIO73_H3", gpio_out_lo),
+	DB8500_PIN_HOG("GPIO74_J3", gpio_out_lo),
+	/* NAHJ CTRL on GPIO 76 to low, CTRL_INV on GPIO216 to high */
+	DB8500_PIN_HOG("GPIO76_J2", gpio_out_lo), /* CTRL */
+	DB8500_PIN_HOG("GPIO216_AG12", gpio_out_hi), /* CTRL_INV */
+	/* NFC ENA and RESET to low, pulldown IRQ line */
+	DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */
+	DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */
+	DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */
+	/*
+	 * SKE keyboard partly on alt A and partly on "Other alt C1"
+	 * Driver KP_O1,2,3,6,7 low and pull up KP_I 0,2,3 for three
+	 * rows of 6 keys, then pull up force sensing interrup and
+	 * drive reset and force sensing WU low.
+	 */
+	DB8500_MUX_HOG("kp_a_1", "kp"),
+	DB8500_MUX_HOG("kp_oc1_1", "kp"),
+	DB8500_PIN_HOG("GPIO90_A3", out_lo), /* KP_O1 */
+	DB8500_PIN_HOG("GPIO87_B3", out_lo), /* KP_O2 */
+	DB8500_PIN_HOG("GPIO86_C6", out_lo), /* KP_O3 */
+	DB8500_PIN_HOG("GPIO96_D8", out_lo), /* KP_O6 */
+	DB8500_PIN_HOG("GPIO94_D7", out_lo), /* KP_O7 */
+	DB8500_PIN_HOG("GPIO93_B7", in_pu), /* KP_I0 */
+	DB8500_PIN_HOG("GPIO89_E6", in_pu), /* KP_I2 */
+	DB8500_PIN_HOG("GPIO88_C4", in_pu), /* KP_I3 */
+	DB8500_PIN_HOG("GPIO91_B6", gpio_in_pu), /* FORCE_SENSING_INT */
+	DB8500_PIN_HOG("GPIO92_D6", gpio_out_lo), /* FORCE_SENSING_RST */
+	DB8500_PIN_HOG("GPIO97_D9", gpio_out_lo), /* FORCE_SENSING_WU */
+	/* DiPro Sensor interrupt */
+	DB8500_PIN_HOG("GPIO139_C9", gpio_in_pu), /* DIPRO_INT */
+	/* Audio Amplifier HF enable */
+	DB8500_PIN_HOG("GPIO149_B14", gpio_out_hi), /* VAUDIO_HF_EN, enable MAX8968 */
+	/* GBF interface, pull low to reset state */
+	DB8500_PIN_HOG("GPIO171_D23", gpio_out_lo), /* GBF_ENA_RESET */
+	/* MSP : HDTV INTERFACE GPIO line */
+	DB8500_PIN_HOG("GPIO192_AJ27", gpio_in_pd),
+	/* Accelerometer interrupt lines */
+	DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */
+	DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
+	/* SD card detect GPIO pin */
+	DB8500_PIN_HOG("GPIO95_E8", gpio_in_pu),
+	/*
+	 * Runtime stuff
+	 * Pull up/down of some sensor GPIO pins, for proximity, HAL sensor
+	 * etc.
+	 */
+	DB8500_PIN("GPIO217_AH12", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"),
+	DB8500_PIN("GPIO145_C13", gpio_in_pd_slpm_gpio_nopull, "gpio-keys.0"),
+	DB8500_PIN("GPIO139_C9", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"),
+	/*
+	 * Make it possible to mux in the SKE keypad and bias the pins
+	 * FIXME: what's the point with this on HREFv60? KP/SKE is already
+	 * muxed in at another place! Enabling this will bork.
+	 */
+	DB8500_MUX("kp_a_2", "kp", "ske"),
+	DB8500_PIN("GPIO153_B17", in_pd_slpm_in_pu, "ske"), /* I7 */
+	DB8500_PIN("GPIO154_C16", in_pd_slpm_in_pu, "ske"), /* I6 */
+	DB8500_PIN("GPIO155_C19", in_pd_slpm_in_pu, "ske"), /* I5 */
+	DB8500_PIN("GPIO156_C17", in_pd_slpm_in_pu, "ske"), /* I4 */
+	DB8500_PIN("GPIO161_D21", in_pd_slpm_in_pu, "ske"), /* I3 */
+	DB8500_PIN("GPIO162_D20", in_pd_slpm_in_pu, "ske"), /* I2 */
+	DB8500_PIN("GPIO163_C20", in_pd_slpm_in_pu, "ske"), /* I1 */
+	DB8500_PIN("GPIO164_B21", in_pd_slpm_in_pu, "ske"), /* I0 */
+	DB8500_PIN("GPIO157_A18", in_pu_slpm_out_lo, "ske"), /* O7 */
+	DB8500_PIN("GPIO158_C18", in_pu_slpm_out_lo, "ske"), /* O6 */
+	DB8500_PIN("GPIO159_B19", in_pu_slpm_out_lo, "ske"), /* O5 */
+	DB8500_PIN("GPIO160_B20", in_pu_slpm_out_lo, "ske"), /* O4 */
+	DB8500_PIN("GPIO165_C21", in_pu_slpm_out_lo, "ske"), /* O3 */
+	DB8500_PIN("GPIO166_A22", in_pu_slpm_out_lo, "ske"), /* O2 */
+	DB8500_PIN("GPIO167_B24", in_pu_slpm_out_lo, "ske"), /* O1 */
+	DB8500_PIN("GPIO168_C22", in_pu_slpm_out_lo, "ske"), /* O0 */
 };
 
-static pin_cfg_t snowball_pins[] = {
-	/* SSP0, to AB8500 */
-	GPIO143_SSP0_CLK,
-	GPIO144_SSP0_FRM,
-	GPIO145_SSP0_RXD	| PIN_PULL_DOWN,
-	GPIO146_SSP0_TXD,
+static struct pinctrl_map __initdata u9500_pinmap[] = {
+	/* Mux in UART1 (just RX/TX) and set the pull-ups */
+	DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
+	DB8500_PIN_HOG("GPIO4_AH6", in_pu),
+	DB8500_PIN_HOG("GPIO5_AG6", out_hi),
+	/* WLAN_IRQ line */
+	DB8500_PIN_HOG("GPIO144_B13", gpio_in_pu),
+	/* HSI */
+	DB8500_MUX_HOG("hsir_a_1", "hsi"),
+	DB8500_MUX_HOG("hsit_a_1", "hsi"),
+	DB8500_PIN_HOG("GPIO219_AG10", in_pd), /* RX FLA0 */
+	DB8500_PIN_HOG("GPIO220_AH10", in_pd), /* RX DAT0 */
+	DB8500_PIN_HOG("GPIO221_AJ11", out_lo), /* RX RDY0 */
+	DB8500_PIN_HOG("GPIO222_AJ9", out_lo), /* TX FLA0 */
+	DB8500_PIN_HOG("GPIO223_AH9", out_lo), /* TX DAT0 */
+	DB8500_PIN_HOG("GPIO224_AG9", in_pd), /* TX RDY0 */
+	DB8500_PIN_HOG("GPIO225_AG8", in_pd), /* CAWAKE0 */
+	DB8500_PIN_HOG("GPIO226_AF8", out_hi), /* ACWAKE0 */
+};
 
-	/* MMC0: MicroSD card */
-	GPIO21_MC0_DAT31DIR     | PIN_OUTPUT_HIGH,
+static struct pinctrl_map __initdata u8500_pinmap[] = {
+	DB8500_PIN_HOG("GPIO226_AF8", gpio_out_lo), /* WLAN_PMU_EN */
+	DB8500_PIN_HOG("GPIO4_AH6", gpio_in_pu), /* WLAN_IRQ */
+};
 
-	/* MMC2: LAN */
-	GPIO86_SM_ADQ0,
-	GPIO87_SM_ADQ1,
-	GPIO88_SM_ADQ2,
-	GPIO89_SM_ADQ3,
-	GPIO90_SM_ADQ4,
-	GPIO91_SM_ADQ5,
-	GPIO92_SM_ADQ6,
-	GPIO93_SM_ADQ7,
+static struct pinctrl_map __initdata snowball_pinmap[] = {
+	/* Mux in SSP0 connected to AB8500, pull down RXD pin */
+	DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
+	DB8500_PIN_HOG("GPIO145_C13", pd),
+	/* Always drive the MC0 DAT31DIR line high on these boards */
+	DB8500_PIN_HOG("GPIO21_AB3", out_hi),
+	/* Mux in "SM" which is used for the SMSC911x Ethernet adapter */
+	DB8500_MUX_HOG("sm_b_1", "sm"),
+	/* Drive RSTn_LAN high */
+	DB8500_PIN_HOG("GPIO141_C12", gpio_out_hi),
+	/*  Accelerometer/Magnetometer */
+	DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */
+	DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */
+	DB8500_PIN_HOG("GPIO165_C21", gpio_in_pu), /* MAG_DRDY */
+	/* WLAN/GBF */
+	DB8500_PIN_HOG("GPIO161_D21", gpio_out_lo), /* WLAN_PMU_EN */
+	DB8500_PIN_HOG("GPIO171_D23", gpio_out_hi), /* GBF_ENA */
+	DB8500_PIN_HOG("GPIO215_AH13", gpio_out_lo), /* WLAN_ENA */
+	DB8500_PIN_HOG("GPIO216_AG12", gpio_in_pu), /* WLAN_IRQ */
+};
 
-	GPIO94_SM_ADVn,
-	GPIO95_SM_CS0n,
-	GPIO96_SM_OEn,
-	GPIO97_SM_WEn,
+/*
+ * passing "pinsfor=" in kernel cmdline allows for custom
+ * configuration of GPIOs on u8500 derived boards.
+ */
+static int __init early_pinsfor(char *p)
+{
+	pinsfor = PINS_FOR_DEFAULT;
 
-	GPIO128_SM_CKO,
-	GPIO130_SM_FBCLK,
-	GPIO131_SM_ADQ8,
-	GPIO132_SM_ADQ9,
-	GPIO133_SM_ADQ10,
-	GPIO134_SM_ADQ11,
-	GPIO135_SM_ADQ12,
-	GPIO136_SM_ADQ13,
-	GPIO137_SM_ADQ14,
-	GPIO138_SM_ADQ15,
+	if (strcmp(p, "u9500-21") == 0)
+		pinsfor = PINS_FOR_U9500;
 
-	/* RSTn_LAN */
-	GPIO141_GPIO		| PIN_OUTPUT_HIGH,
-};
+	return 0;
+}
+early_param("pinsfor", early_pinsfor);
 
-void __init mop500_pins_init(void)
+int pins_for_u9500(void)
 {
-	nmk_config_pins(mop500_pins_common,
-			ARRAY_SIZE(mop500_pins_common));
+	if (pinsfor == PINS_FOR_U9500)
+		return 1;
 
-	nmk_config_pins(mop500_pins_default,
-			ARRAY_SIZE(mop500_pins_default));
+	return 0;
 }
 
-void __init snowball_pins_init(void)
+static void __init mop500_href_family_pinmaps_init(void)
 {
-	nmk_config_pins(mop500_pins_common,
-			ARRAY_SIZE(mop500_pins_common));
+	switch (pinsfor) {
+	case PINS_FOR_U9500:
+		pinctrl_register_mappings(u9500_pinmap,
+					  ARRAY_SIZE(u9500_pinmap));
+		break;
+	case PINS_FOR_DEFAULT:
+		pinctrl_register_mappings(u8500_pinmap,
+					  ARRAY_SIZE(u8500_pinmap));
+	default:
+		break;
+	}
+}
 
-	nmk_config_pins(snowball_pins,
-			ARRAY_SIZE(snowball_pins));
+void __init mop500_pinmaps_init(void)
+{
+	pinctrl_register_mappings(mop500_family_pinmap,
+				  ARRAY_SIZE(mop500_family_pinmap));
+	pinctrl_register_mappings(mop500_pinmap,
+				  ARRAY_SIZE(mop500_pinmap));
+	mop500_href_family_pinmaps_init();
 }
 
-void __init hrefv60_pins_init(void)
+void __init snowball_pinmaps_init(void)
 {
-	nmk_config_pins(mop500_pins_common,
-			ARRAY_SIZE(mop500_pins_common));
+	pinctrl_register_mappings(mop500_family_pinmap,
+				  ARRAY_SIZE(mop500_family_pinmap));
+	pinctrl_register_mappings(snowball_pinmap,
+				  ARRAY_SIZE(snowball_pinmap));
+	pinctrl_register_mappings(u8500_pinmap,
+				  ARRAY_SIZE(u8500_pinmap));
+}
 
-	nmk_config_pins(hrefv60_pins,
-			ARRAY_SIZE(hrefv60_pins));
+void __init hrefv60_pinmaps_init(void)
+{
+	pinctrl_register_mappings(mop500_family_pinmap,
+				  ARRAY_SIZE(mop500_family_pinmap));
+	pinctrl_register_mappings(hrefv60_pinmap,
+				  ARRAY_SIZE(hrefv60_pinmap));
+	mop500_href_family_pinmaps_init();
 }
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index f8150155a44..4bc0cbc5f07 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -1,3 +1,4 @@
+
 /*
  * Copyright (C) 2008-2009 ST-Ericsson
  *
@@ -29,18 +30,17 @@
 #include <linux/smsc911x.h>
 #include <linux/gpio_keys.h>
 #include <linux/delay.h>
-
 #include <linux/of.h>
 #include <linux/of_platform.h>
-
 #include <linux/leds.h>
+#include <linux/pinctrl/consumer.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
 
 #include <plat/i2c.h>
 #include <plat/ste_dma40.h>
-#include <plat/pincfg.h>
 #include <plat/gpio-nomadik.h>
 
 #include <mach/hardware.h>
@@ -48,11 +48,11 @@
 #include <mach/devices.h>
 #include <mach/irqs.h>
 
-#include "pins-db8500.h"
 #include "ste-dma40-db8500.h"
 #include "devices-db8500.h"
 #include "board-mop500.h"
 #include "board-mop500-regulators.h"
+#include "board-mop500-msp.h"
 
 static struct gpio_led snowball_led_array[] = {
 	{
@@ -520,14 +520,6 @@ static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
 };
 #endif
 
-
-static pin_cfg_t mop500_pins_uart0[] = {
-	GPIO0_U0_CTSn   | PIN_INPUT_PULLUP,
-	GPIO1_U0_RTSn   | PIN_OUTPUT_HIGH,
-	GPIO2_U0_RXD    | PIN_INPUT_PULLUP,
-	GPIO3_U0_TXD    | PIN_OUTPUT_HIGH,
-};
-
 #define PRCC_K_SOFTRST_SET      0x18
 #define PRCC_K_SOFTRST_CLEAR    0x1C
 static void ux500_uart0_reset(void)
@@ -548,24 +540,33 @@ static void ux500_uart0_reset(void)
 	udelay(1);
 }
 
+/* This needs to be referenced by callbacks */
+struct pinctrl *u0_p;
+struct pinctrl_state *u0_def;
+struct pinctrl_state *u0_sleep;
+
 static void ux500_uart0_init(void)
 {
 	int ret;
 
-	ret = nmk_config_pins(mop500_pins_uart0,
-			ARRAY_SIZE(mop500_pins_uart0));
-	if (ret < 0)
-		pr_err("pl011: uart pins_enable failed\n");
+	if (IS_ERR(u0_p) || IS_ERR(u0_def))
+		return;
+
+	ret = pinctrl_select_state(u0_p, u0_def);
+	if (ret)
+		pr_err("could not set UART0 defstate\n");
 }
 
 static void ux500_uart0_exit(void)
 {
 	int ret;
 
-	ret = nmk_config_pins_sleep(mop500_pins_uart0,
-			ARRAY_SIZE(mop500_pins_uart0));
-	if (ret < 0)
-		pr_err("pl011: uart pins_disable failed\n");
+	if (IS_ERR(u0_p) || IS_ERR(u0_sleep))
+		return;
+
+	ret = pinctrl_select_state(u0_p, u0_sleep);
+	if (ret)
+		pr_err("could not set UART0 idlestate\n");
 }
 
 static struct amba_pl011_data uart0_plat = {
@@ -597,7 +598,28 @@ static struct amba_pl011_data uart2_plat = {
 
 static void __init mop500_uart_init(struct device *parent)
 {
-	db8500_add_uart0(parent, &uart0_plat);
+	struct amba_device *uart0_device;
+
+	uart0_device = db8500_add_uart0(parent, &uart0_plat);
+	if (uart0_device) {
+		u0_p = pinctrl_get(&uart0_device->dev);
+		if (IS_ERR(u0_p))
+			dev_err(&uart0_device->dev,
+				"could not get UART0 pinctrl\n");
+		else {
+			u0_def = pinctrl_lookup_state(u0_p,
+						      PINCTRL_STATE_DEFAULT);
+			if (IS_ERR(u0_def)) {
+				dev_err(&uart0_device->dev,
+					"could not get UART0 defstate\n");
+			}
+			u0_sleep = pinctrl_lookup_state(u0_p,
+							PINCTRL_STATE_SLEEP);
+			if (IS_ERR(u0_sleep))
+				dev_err(&uart0_device->dev,
+					"could not get UART0 idlestate\n");
+		}
+	}
 	db8500_add_uart1(parent, &uart1_plat);
 	db8500_add_uart2(parent, &uart2_plat);
 }
@@ -616,10 +638,9 @@ static void __init mop500_init_machine(void)
 
 	mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;
 
+	mop500_pinmaps_init();
 	parent = u8500_init_devices();
 
-	mop500_pins_init();
-
 	/* FIXME: parent of ab8500 should be prcmu */
 	for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
 		mop500_platform_devs[i]->dev.parent = parent;
@@ -630,6 +651,7 @@ static void __init mop500_init_machine(void)
 	mop500_i2c_init(parent);
 	mop500_sdi_init(parent);
 	mop500_spi_init(parent);
+	mop500_msp_init(parent);
 	mop500_uart_init(parent);
 
 	i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices);
@@ -647,10 +669,9 @@ static void __init snowball_init_machine(void)
 	struct device *parent = NULL;
 	int i;
 
+	snowball_pinmaps_init();
 	parent = u8500_init_devices();
 
-	snowball_pins_init();
-
 	for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
 		snowball_platform_devs[i]->dev.parent = parent;
 
@@ -660,6 +681,7 @@ static void __init snowball_init_machine(void)
 	mop500_i2c_init(parent);
 	snowball_sdi_init(parent);
 	mop500_spi_init(parent);
+	mop500_msp_init(parent);
 	mop500_uart_init(parent);
 
 	/* This board has full regulator constraints */
@@ -679,10 +701,9 @@ static void __init hrefv60_init_machine(void)
 	 */
 	mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO;
 
+	hrefv60_pinmaps_init();
 	parent = u8500_init_devices();
 
-	hrefv60_pins_init();
-
 	for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
 		mop500_platform_devs[i]->dev.parent = parent;
 
@@ -692,6 +713,7 @@ static void __init hrefv60_init_machine(void)
 	mop500_i2c_init(parent);
 	hrefv60_sdi_init(parent);
 	mop500_spi_init(parent);
+	mop500_msp_init(parent);
 	mop500_uart_init(parent);
 
 	i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices);
@@ -739,10 +761,22 @@ MACHINE_END
 #ifdef CONFIG_MACH_UX500_DT
 
 struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
+	/* Requires DMA and call-back bindings. */
 	OF_DEV_AUXDATA("arm,pl011", 0x80120000, "uart0", &uart0_plat),
 	OF_DEV_AUXDATA("arm,pl011", 0x80121000, "uart1", &uart1_plat),
 	OF_DEV_AUXDATA("arm,pl011", 0x80007000, "uart2", &uart2_plat),
+	/* Requires DMA bindings. */
 	OF_DEV_AUXDATA("arm,pl022", 0x80002000, "ssp0",  &ssp0_plat),
+	/* Requires clock name bindings. */
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e000, "gpio.0", NULL),
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e080, "gpio.1", NULL),
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e000, "gpio.2", NULL),
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e080, "gpio.3", NULL),
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e100, "gpio.4", NULL),
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e180, "gpio.5", NULL),
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e000, "gpio.6", NULL),
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e080, "gpio.7", NULL),
+	OF_DEV_AUXDATA("st,nomadik-gpio", 0xa03fe000, "gpio.8", NULL),
 	{},
 };
 
@@ -759,6 +793,14 @@ static void __init u8500_init_machine(void)
 	int i2c0_devs;
 	int i;
 
+	/* Pinmaps must be in place before devices register */
+	if (of_machine_is_compatible("st-ericsson,mop500"))
+		mop500_pinmaps_init();
+	else if (of_machine_is_compatible("calaosystems,snowball-a9500"))
+		snowball_pinmaps_init();
+	else if (of_machine_is_compatible("st-ericsson,hrefv60+"))
+		hrefv60_pinmaps_init();
+
 	parent = u8500_init_devices();
 
 	for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
@@ -771,7 +813,6 @@ static void __init u8500_init_machine(void)
 
 	if (of_machine_is_compatible("st-ericsson,mop500")) {
 		mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;
-		mop500_pins_init();
 
 		platform_add_devices(mop500_platform_devs,
 				ARRAY_SIZE(mop500_platform_devs));
@@ -784,7 +825,6 @@ static void __init u8500_init_machine(void)
 					ARRAY_SIZE(mop500_i2c2_devices));
 
 	} else if (of_machine_is_compatible("calaosystems,snowball-a9500")) {
-		snowball_pins_init();
 		platform_add_devices(snowball_platform_devs,
 				ARRAY_SIZE(snowball_platform_devs));
 
@@ -796,7 +836,6 @@ static void __init u8500_init_machine(void)
 		 * instead.
 		 */
 		mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO;
-		hrefv60_pins_init();
 		platform_add_devices(mop500_platform_devs,
 				ARRAY_SIZE(mop500_platform_devs));
 
diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h
index fdcfa8721bb..bc44c07c71a 100644
--- a/arch/arm/mach-ux500/board-mop500.h
+++ b/arch/arm/mach-ux500/board-mop500.h
@@ -7,6 +7,9 @@
 #ifndef __BOARD_MOP500_H
 #define __BOARD_MOP500_H
 
+/* For NOMADIK_NR_GPIO */
+#include <mach/irqs.h>
+
 /* Snowball specific GPIO assignments, this board has no GPIO expander */
 #define SNOWBALL_ACCEL_INT1_GPIO	163
 #define SNOWBALL_ACCEL_INT2_GPIO	164
@@ -73,6 +76,7 @@
 #define SNOWBALL_PME_ETH_GPIO		MOP500_AB8500_PIN_GPIO(24)	/* SYSCLKREQ7/GPIO24 */
 #define SNOWBALL_EN_3V3_ETH_GPIO	MOP500_AB8500_PIN_GPIO(26)	/* GPIO26 */
 
+struct device;
 struct i2c_board_info;
 
 extern void mop500_sdi_init(struct device *parent);
@@ -81,9 +85,9 @@ extern void hrefv60_sdi_init(struct device *parent);
 extern void mop500_sdi_tc35892_init(struct device *parent);
 void __init mop500_u8500uib_init(void);
 void __init mop500_stuib_init(void);
-void __init mop500_pins_init(void);
-void __init hrefv60_pins_init(void);
-void __init snowball_pins_init(void);
+void __init mop500_pinmaps_init(void);
+void __init snowball_pinmaps_init(void);
+void __init hrefv60_pinmaps_init(void);
 
 void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
 		unsigned n);
diff --git a/arch/arm/mach-ux500/clock.c b/arch/arm/mach-ux500/clock.c
index 063f3dbd45a..a121cb472dd 100644
--- a/arch/arm/mach-ux500/clock.c
+++ b/arch/arm/mach-ux500/clock.c
@@ -334,6 +334,7 @@ static DEFINE_PRCMU_CLK(uiccclk,	0x4, 1, UICCCLK); /* v1 */
  */
 
 /* Peripheral Cluster #1 */
+static DEFINE_PRCC_CLK(1, msp3,		11, 10, &clk_msp1clk);
 static DEFINE_PRCC_CLK(1, i2c4,		10, 9, &clk_i2cclk);
 static DEFINE_PRCC_CLK(1, gpio0,	9, -1, NULL);
 static DEFINE_PRCC_CLK(1, slimbus0,	8,  8, &clk_slimclk);
@@ -403,7 +404,7 @@ static struct clk_lookup u8500_clks[] = {
 	CLK(slimbus0,	"slimbus0",	NULL),
 	CLK(i2c2,	"nmk-i2c.2",	NULL),
 	CLK(sdi0,	"sdi0",		NULL),
-	CLK(msp0,	"msp0",		NULL),
+	CLK(msp0,	"ux500-msp-i2s.0",	NULL),
 	CLK(i2c1,	"nmk-i2c.1",	NULL),
 	CLK(uart1,	"uart1",	NULL),
 	CLK(uart0,	"uart0",	NULL),
@@ -453,7 +454,8 @@ static struct clk_lookup u8500_clks[] = {
 	/* Peripheral Cluster #1 */
 	CLK(i2c4,	"nmk-i2c.4",	NULL),
 	CLK(spi3,	"spi3",		NULL),
-	CLK(msp1,	"msp1",		NULL),
+	CLK(msp1,	"ux500-msp-i2s.1",	NULL),
+	CLK(msp3,	"ux500-msp-i2s.3",	NULL),
 
 	/* Peripheral Cluster #2 */
 	CLK(gpio1,	"gpio.6",	NULL),
@@ -463,7 +465,7 @@ static struct clk_lookup u8500_clks[] = {
 	CLK(spi0,	"spi0",		NULL),
 	CLK(sdi3,	"sdi3",		NULL),
 	CLK(sdi1,	"sdi1",		NULL),
-	CLK(msp2,	"msp2",		NULL),
+	CLK(msp2,	"ux500-msp-i2s.2",	NULL),
 	CLK(sdi4,	"sdi4",		NULL),
 	CLK(pwl,	"pwl",		NULL),
 	CLK(spi1,	"spi1",		NULL),
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 76a7503a11a..16169c4bf6c 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -163,6 +163,7 @@ static void __init db8500_add_gpios(struct device *parent)
 
 	dbx500_add_gpios(parent, ARRAY_AND_SIZE(db8500_gpio_base),
 			 IRQ_DB8500_GPIO0, &pdata);
+	dbx500_add_pinctrl(parent, "pinctrl-db8500");
 }
 
 static int usb_db8500_rx_dma_cfg[] = {
diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c
index 0982279f51f..a29a0e3adcf 100644
--- a/arch/arm/mach-ux500/cpu.c
+++ b/arch/arm/mach-ux500/cpu.c
@@ -29,6 +29,18 @@
 
 void __iomem *_PRCMU_BASE;
 
+/*
+ * FIXME: Should we set up the GPIO domain here?
+ *
+ * The problem is that we cannot put the interrupt resources into the platform
+ * device until the irqdomain has been added. Right now, we set the GIC interrupt
+ * domain from init_irq(), then load the gpio driver from
+ * core_initcall(nmk_gpio_init) and add the platform devices from
+ * arch_initcall(customize_machine).
+ *
+ * This feels fragile because it depends on the gpio device getting probed
+ * _before_ any device uses the gpio interrupts.
+*/
 static const struct of_device_id ux500_dt_irq_match[] = {
 	{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
 	{},
diff --git a/arch/arm/mach-ux500/devices-common.h b/arch/arm/mach-ux500/devices-common.h
index f75bcb2ab13..7cbccfd9e15 100644
--- a/arch/arm/mach-ux500/devices-common.h
+++ b/arch/arm/mach-ux500/devices-common.h
@@ -90,4 +90,16 @@ struct nmk_gpio_platform_data;
 void dbx500_add_gpios(struct device *parent, resource_size_t *base, int num,
 		      int irq, struct nmk_gpio_platform_data *pdata);
 
+static inline void
+dbx500_add_pinctrl(struct device *parent, const char *name)
+{
+	struct platform_device_info pdevinfo = {
+		.parent = parent,
+		.name = name,
+		.id = -1,
+	};
+
+	platform_device_register_full(&pdevinfo);
+}
+
 #endif
diff --git a/arch/arm/mach-ux500/devices-db8500.h b/arch/arm/mach-ux500/devices-db8500.h
index 6fc7eb24d9a..0b9677a95bb 100644
--- a/arch/arm/mach-ux500/devices-db8500.h
+++ b/arch/arm/mach-ux500/devices-db8500.h
@@ -34,7 +34,6 @@ db8500_add_ssp(struct device *parent, const char *name, resource_size_t base,
 	return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, pdata, 0);
 }
 
-
 #define db8500_add_i2c0(parent, pdata) \
 	dbx500_add_i2c(parent, 0, U8500_I2C0_BASE, IRQ_DB8500_I2C0, pdata)
 #define db8500_add_i2c1(parent, pdata) \
@@ -46,15 +45,6 @@ db8500_add_ssp(struct device *parent, const char *name, resource_size_t base,
 #define db8500_add_i2c4(parent, pdata) \
 	dbx500_add_i2c(parent, 4, U8500_I2C4_BASE, IRQ_DB8500_I2C4, pdata)
 
-#define db8500_add_msp0_i2s(parent, pdata) \
-	dbx500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0, pdata)
-#define db8500_add_msp1_i2s(parent, pdata) \
-	dbx500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1, pdata)
-#define db8500_add_msp2_i2s(parent, pdata) \
-	dbx500_add_msp_i2s(parent, 2, U8500_MSP2_BASE, IRQ_DB8500_MSP2, pdata)
-#define db8500_add_msp3_i2s(parent, pdata) \
-	dbx500_add_msp_i2s(parent, 3, U8500_MSP3_BASE, IRQ_DB8500_MSP1, pdata)
-
 #define db8500_add_msp0_spi(parent, pdata) \
 	dbx500_add_msp_spi(parent, "msp0", U8500_MSP0_BASE, \
 			   IRQ_DB8500_MSP0, pdata)
diff --git a/arch/arm/mach-ux500/include/mach/msp.h b/arch/arm/mach-ux500/include/mach/msp.h
new file mode 100644
index 00000000000..798be19129e
--- /dev/null
+++ b/arch/arm/mach-ux500/include/mach/msp.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
+ * License terms: GNU General Public License (GPL), version 2.
+ */
+
+#ifndef __MSP_H
+#define __MSP_H
+
+#include <plat/ste_dma40.h>
+
+enum msp_i2s_id {
+	MSP_I2S_0 = 0,
+	MSP_I2S_1,
+	MSP_I2S_2,
+	MSP_I2S_3,
+};
+
+/* Platform data structure for a MSP I2S-device */
+struct msp_i2s_platform_data {
+	enum msp_i2s_id id;
+	struct stedma40_chan_cfg *msp_i2s_dma_rx;
+	struct stedma40_chan_cfg *msp_i2s_dma_tx;
+	int (*msp_i2s_init) (void);
+	int (*msp_i2s_exit) (void);
+};
+
+#endif
diff --git a/arch/arm/mach-ux500/pins-db8500.h b/arch/arm/mach-ux500/pins-db8500.h
index 8b1d1a7a679..062c7acf457 100644
--- a/arch/arm/mach-ux500/pins-db8500.h
+++ b/arch/arm/mach-ux500/pins-db8500.h
@@ -35,40 +35,40 @@
 
 #define GPIO4_GPIO		PIN_CFG(4, GPIO)
 #define GPIO4_U1_RXD		PIN_CFG(4, ALT_A)
-#define GPIO4_I2C4_SCL		PIN_CFG_INPUT(4, ALT_B, PULLUP)
+#define GPIO4_I2C4_SCL		PIN_CFG(4, ALT_B)
 #define GPIO4_IP_TRSTn		PIN_CFG(4, ALT_C)
 
 #define GPIO5_GPIO		PIN_CFG(5, GPIO)
 #define GPIO5_U1_TXD		PIN_CFG(5, ALT_A)
-#define GPIO5_I2C4_SDA		PIN_CFG_INPUT(5, ALT_B, PULLUP)
+#define GPIO5_I2C4_SDA		PIN_CFG(5, ALT_B)
 #define GPIO5_IP_GPIO6		PIN_CFG(5, ALT_C)
 
 #define GPIO6_GPIO		PIN_CFG(6, GPIO)
 #define GPIO6_U1_CTSn		PIN_CFG(6, ALT_A)
-#define GPIO6_I2C1_SCL		PIN_CFG_INPUT(6, ALT_B, PULLUP)
+#define GPIO6_I2C1_SCL		PIN_CFG(6, ALT_B)
 #define GPIO6_IP_GPIO0		PIN_CFG(6, ALT_C)
 
 #define GPIO7_GPIO		PIN_CFG(7, GPIO)
 #define GPIO7_U1_RTSn		PIN_CFG(7, ALT_A)
-#define GPIO7_I2C1_SDA		PIN_CFG_INPUT(7, ALT_B, PULLUP)
+#define GPIO7_I2C1_SDA		PIN_CFG(7, ALT_B)
 #define GPIO7_IP_GPIO1		PIN_CFG(7, ALT_C)
 
 #define GPIO8_GPIO		PIN_CFG(8, GPIO)
-#define GPIO8_IPI2C_SDA		PIN_CFG_INPUT(8, ALT_A, PULLUP)
-#define GPIO8_I2C2_SDA		PIN_CFG_INPUT(8, ALT_B, PULLUP)
+#define GPIO8_IPI2C_SDA		PIN_CFG(8, ALT_A)
+#define GPIO8_I2C2_SDA		PIN_CFG(8, ALT_B)
 
 #define GPIO9_GPIO		PIN_CFG(9, GPIO)
-#define GPIO9_IPI2C_SCL		PIN_CFG_INPUT(9, ALT_A, PULLUP)
-#define GPIO9_I2C2_SCL		PIN_CFG_INPUT(9, ALT_B, PULLUP)
+#define GPIO9_IPI2C_SCL		PIN_CFG(9, ALT_A)
+#define GPIO9_I2C2_SCL		PIN_CFG(9, ALT_B)
 
 #define GPIO10_GPIO		PIN_CFG(10, GPIO)
-#define GPIO10_IPI2C_SDA	PIN_CFG_INPUT(10, ALT_A, PULLUP)
-#define GPIO10_I2C2_SDA		PIN_CFG_INPUT(10, ALT_B, PULLUP)
+#define GPIO10_IPI2C_SDA	PIN_CFG(10, ALT_A)
+#define GPIO10_I2C2_SDA		PIN_CFG(10, ALT_B)
 #define GPIO10_IP_GPIO3		PIN_CFG(10, ALT_C)
 
 #define GPIO11_GPIO		PIN_CFG(11, GPIO)
-#define GPIO11_IPI2C_SCL	PIN_CFG_INPUT(11, ALT_A, PULLUP)
-#define GPIO11_I2C2_SCL		PIN_CFG_INPUT(11, ALT_B, PULLUP)
+#define GPIO11_IPI2C_SCL	PIN_CFG(11, ALT_A)
+#define GPIO11_I2C2_SCL		PIN_CFG(11, ALT_B)
 #define GPIO11_IP_GPIO2		PIN_CFG(11, ALT_C)
 
 #define GPIO12_GPIO		PIN_CFG(12, GPIO)
@@ -87,12 +87,12 @@
 
 #define GPIO16_GPIO		PIN_CFG(16, GPIO)
 #define GPIO16_MSP0_RFS		PIN_CFG(16, ALT_A)
-#define GPIO16_I2C1_SCL		PIN_CFG_INPUT(16, ALT_B, PULLUP)
+#define GPIO16_I2C1_SCL		PIN_CFG(16, ALT_B)
 #define GPIO16_SLIM0_DAT	PIN_CFG(16, ALT_C)
 
 #define GPIO17_GPIO		PIN_CFG(17, GPIO)
 #define GPIO17_MSP0_RCK		PIN_CFG(17, ALT_A)
-#define GPIO17_I2C1_SDA		PIN_CFG_INPUT(17, ALT_B, PULLUP)
+#define GPIO17_I2C1_SDA		PIN_CFG(17, ALT_B)
 #define GPIO17_SLIM0_CLK	PIN_CFG(17, ALT_C)
 
 #define GPIO18_GPIO		PIN_CFG(18, GPIO)
@@ -434,10 +434,10 @@
 #define GPIO146_SSP0_TXD	PIN_CFG(146, ALT_A)
 
 #define GPIO147_GPIO		PIN_CFG(147, GPIO)
-#define GPIO147_I2C0_SCL	PIN_CFG_INPUT(147, ALT_A, PULLUP)
+#define GPIO147_I2C0_SCL	PIN_CFG(147, ALT_A)
 
 #define GPIO148_GPIO		PIN_CFG(148, GPIO)
-#define GPIO148_I2C0_SDA	PIN_CFG_INPUT(148, ALT_A, PULLUP)
+#define GPIO148_I2C0_SDA	PIN_CFG(148, ALT_A)
 
 #define GPIO149_GPIO		PIN_CFG(149, GPIO)
 #define GPIO149_IP_GPIO0	PIN_CFG(149, ALT_A)
@@ -459,82 +459,82 @@
 #define GPIO152_KP_O9		PIN_CFG(152, ALT_C)
 
 #define GPIO153_GPIO		PIN_CFG(153, GPIO)
-#define GPIO153_KP_I7		PIN_CFG_INPUT(153, ALT_A, PULLDOWN)
+#define GPIO153_KP_I7		PIN_CFG(153, ALT_A)
 #define GPIO153_LCD_D24		PIN_CFG(153, ALT_B)
 #define GPIO153_U2_RXD		PIN_CFG(153, ALT_C)
 
 #define GPIO154_GPIO		PIN_CFG(154, GPIO)
-#define GPIO154_KP_I6		PIN_CFG_INPUT(154, ALT_A, PULLDOWN)
+#define GPIO154_KP_I6		PIN_CFG(154, ALT_A)
 #define GPIO154_LCD_D25		PIN_CFG(154, ALT_B)
 #define GPIO154_U2_TXD		PIN_CFG(154, ALT_C)
 
 #define GPIO155_GPIO		PIN_CFG(155, GPIO)
-#define GPIO155_KP_I5		PIN_CFG_INPUT(155, ALT_A, PULLDOWN)
+#define GPIO155_KP_I5		PIN_CFG(155, ALT_A)
 #define GPIO155_LCD_D26		PIN_CFG(155, ALT_B)
 #define GPIO155_STMAPE_CLK	PIN_CFG(155, ALT_C)
 
 #define GPIO156_GPIO		PIN_CFG(156, GPIO)
-#define GPIO156_KP_I4		PIN_CFG_INPUT(156, ALT_A, PULLDOWN)
+#define GPIO156_KP_I4		PIN_CFG(156, ALT_A)
 #define GPIO156_LCD_D27		PIN_CFG(156, ALT_B)
 #define GPIO156_STMAPE_DAT3	PIN_CFG(156, ALT_C)
 
 #define GPIO157_GPIO		PIN_CFG(157, GPIO)
-#define GPIO157_KP_O7		PIN_CFG_INPUT(157, ALT_A, PULLUP)
+#define GPIO157_KP_O7		PIN_CFG(157, ALT_A)
 #define GPIO157_LCD_D28		PIN_CFG(157, ALT_B)
 #define GPIO157_STMAPE_DAT2	PIN_CFG(157, ALT_C)
 
 #define GPIO158_GPIO		PIN_CFG(158, GPIO)
-#define GPIO158_KP_O6		PIN_CFG_INPUT(158, ALT_A, PULLUP)
+#define GPIO158_KP_O6		PIN_CFG(158, ALT_A)
 #define GPIO158_LCD_D29		PIN_CFG(158, ALT_B)
 #define GPIO158_STMAPE_DAT1	PIN_CFG(158, ALT_C)
 
 #define GPIO159_GPIO		PIN_CFG(159, GPIO)
-#define GPIO159_KP_O5		PIN_CFG_INPUT(159, ALT_A, PULLUP)
+#define GPIO159_KP_O5		PIN_CFG(159, ALT_A)
 #define GPIO159_LCD_D30		PIN_CFG(159, ALT_B)
 #define GPIO159_STMAPE_DAT0	PIN_CFG(159, ALT_C)
 
 #define GPIO160_GPIO		PIN_CFG(160, GPIO)
-#define GPIO160_KP_O4		PIN_CFG_INPUT(160, ALT_A, PULLUP)
+#define GPIO160_KP_O4		PIN_CFG(160, ALT_A)
 #define GPIO160_LCD_D31		PIN_CFG(160, ALT_B)
 #define GPIO160_NONE		PIN_CFG(160, ALT_C)
 
 #define GPIO161_GPIO		PIN_CFG(161, GPIO)
-#define GPIO161_KP_I3		PIN_CFG_INPUT(161, ALT_A, PULLDOWN)
+#define GPIO161_KP_I3		PIN_CFG(161, ALT_A)
 #define GPIO161_LCD_D32		PIN_CFG(161, ALT_B)
 #define GPIO161_UARTMOD_RXD	PIN_CFG(161, ALT_C)
 
 #define GPIO162_GPIO		PIN_CFG(162, GPIO)
-#define GPIO162_KP_I2		PIN_CFG_INPUT(162, ALT_A, PULLDOWN)
+#define GPIO162_KP_I2		PIN_CFG(162, ALT_A)
 #define GPIO162_LCD_D33		PIN_CFG(162, ALT_B)
 #define GPIO162_UARTMOD_TXD	PIN_CFG(162, ALT_C)
 
 #define GPIO163_GPIO		PIN_CFG(163, GPIO)
-#define GPIO163_KP_I1		PIN_CFG_INPUT(163, ALT_A, PULLDOWN)
+#define GPIO163_KP_I1		PIN_CFG(163, ALT_A)
 #define GPIO163_LCD_D34		PIN_CFG(163, ALT_B)
 #define GPIO163_STMMOD_CLK	PIN_CFG(163, ALT_C)
 
 #define GPIO164_GPIO		PIN_CFG(164, GPIO)
-#define GPIO164_KP_I0		PIN_CFG_INPUT(164, ALT_A, PULLUP)
+#define GPIO164_KP_I0		PIN_CFG(164, ALT_A)
 #define GPIO164_LCD_D35		PIN_CFG(164, ALT_B)
 #define GPIO164_STMMOD_DAT3	PIN_CFG(164, ALT_C)
 
 #define GPIO165_GPIO		PIN_CFG(165, GPIO)
-#define GPIO165_KP_O3		PIN_CFG_INPUT(165, ALT_A, PULLUP)
+#define GPIO165_KP_O3		PIN_CFG(165, ALT_A)
 #define GPIO165_LCD_D36		PIN_CFG(165, ALT_B)
 #define GPIO165_STMMOD_DAT2	PIN_CFG(165, ALT_C)
 
 #define GPIO166_GPIO		PIN_CFG(166, GPIO)
-#define GPIO166_KP_O2		PIN_CFG_INPUT(166, ALT_A, PULLUP)
+#define GPIO166_KP_O2		PIN_CFG(166, ALT_A)
 #define GPIO166_LCD_D37		PIN_CFG(166, ALT_B)
 #define GPIO166_STMMOD_DAT1	PIN_CFG(166, ALT_C)
 
 #define GPIO167_GPIO		PIN_CFG(167, GPIO)
-#define GPIO167_KP_O1		PIN_CFG_INPUT(167, ALT_A, PULLUP)
+#define GPIO167_KP_O1		PIN_CFG(167, ALT_A)
 #define GPIO167_LCD_D38		PIN_CFG(167, ALT_B)
 #define GPIO167_STMMOD_DAT0	PIN_CFG(167, ALT_C)
 
 #define GPIO168_GPIO		PIN_CFG(168, GPIO)
-#define GPIO168_KP_O0		PIN_CFG_INPUT(168, ALT_A, PULLUP)
+#define GPIO168_KP_O0		PIN_CFG(168, ALT_A)
 #define GPIO168_LCD_D39		PIN_CFG(168, ALT_B)
 #define GPIO168_NONE		PIN_CFG(168, ALT_C)
 
@@ -637,7 +637,7 @@
 #define GPIO216_GPIO		PIN_CFG(216, GPIO)
 #define GPIO216_MC1_DAT2DIR	PIN_CFG(216, ALT_A)
 #define GPIO216_MC3_CMDDIR	PIN_CFG(216, ALT_B)
-#define GPIO216_I2C3_SDA	PIN_CFG_INPUT(216, ALT_C, PULLUP)
+#define GPIO216_I2C3_SDA	PIN_CFG(216, ALT_C)
 #define GPIO216_SPI2_FRM	PIN_CFG(216, ALT_C)
 
 #define GPIO217_GPIO		PIN_CFG(217, GPIO)
@@ -649,7 +649,7 @@
 #define GPIO218_GPIO		PIN_CFG(218, GPIO)
 #define GPIO218_MC1_DAT31DIR	PIN_CFG(218, ALT_A)
 #define GPIO218_MC3_DAT0DIR	PIN_CFG(218, ALT_B)
-#define GPIO218_I2C3_SCL	PIN_CFG_INPUT(218, ALT_C, PULLUP)
+#define GPIO218_I2C3_SCL	PIN_CFG(218, ALT_C)
 #define GPIO218_SPI2_RXD	PIN_CFG(218, ALT_C)
 
 #define GPIO219_GPIO		PIN_CFG(219, GPIO)
@@ -698,12 +698,12 @@
 #define GPIO229_GPIO		PIN_CFG(229, GPIO)
 #define GPIO229_CLKOUT1		PIN_CFG(229, ALT_A)
 #define GPIO229_PWL		PIN_CFG(229, ALT_B)
-#define GPIO229_I2C3_SDA	PIN_CFG_INPUT(229, ALT_C, PULLUP)
+#define GPIO229_I2C3_SDA	PIN_CFG(229, ALT_C)
 
 #define GPIO230_GPIO		PIN_CFG(230, GPIO)
 #define GPIO230_CLKOUT2		PIN_CFG(230, ALT_A)
 #define GPIO230_PWL		PIN_CFG(230, ALT_B)
-#define GPIO230_I2C3_SCL	PIN_CFG_INPUT(230, ALT_C, PULLUP)
+#define GPIO230_I2C3_SCL	PIN_CFG(230, ALT_C)
 
 #define GPIO256_GPIO		PIN_CFG(256, GPIO)
 #define GPIO256_USB_NXT		PIN_CFG(256, ALT_A)