Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
  arm: remove machine_desc.io_pg_offst and .phys_io
  arm: use addruart macro to establish debug mappings
  arm: return both physical and virtual addresses from addruart
  arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
  ARM: make struct machine_desc definition coherent with its comment
  eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
  cpuimx27: fix compile when ULPI is selected
  mach-pcm037_eet: fix compile errors
  Fixing ethernet driver compilation error for i.MX31 ADS board
  cpuimx51: update board support
  mx5: add cpuimx51sd module and its baseboard
  iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
  imx-esdhc: update devices registration
  mx51: add resources for SD/MMC on i.MX51
  iomux-mx51: fix SD1 and SD2's iomux configuration
  clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
  clock-mx51: factorize clk_set_parent and clk_get_rate
  eukrea_mbimxsd: add support for DVI displays
  cpuimx25 & cpuimx35: fix OTG port registration in host mode
  i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
  ...

1 files changed, 34 insertions, 2 deletions

diff --git a/arch/arm/plat-nomadik/include/plat/pincfg.h b/arch/arm/plat-nomadik/include/plat/pincfg.h
index 7eed11c1038..8c5ae3f2acf 100644
--- a/arch/arm/plat-nomadik/include/plat/pincfg.h
+++ b/arch/arm/plat-nomadik/include/plat/pincfg.h
@@ -19,12 +19,16 @@
  *	bit  9..10 - Alternate Function Selection
  *	bit 11..12 - Pull up/down state
  *	bit     13 - Sleep mode behaviour
+ *	bit     14 - (sleep mode) Direction
+ *	bit     15 - (sleep mode) Value (if output)
  *
  * to facilitate the definition, the following macros are provided
  *
  * PIN_CFG_DEFAULT - default config (0):
  *		     pull up/down = disabled
- *		     sleep mode = input
+ *		     sleep mode = input/wakeup
+ *		     (sleep mode) direction = input
+ *		     (sleep mode) value = low
  *
  * PIN_CFG	   - default config with alternate function
  * PIN_CFG_PULL	   - default config with alternate function and pull up/down
@@ -53,8 +57,36 @@ typedef unsigned long pin_cfg_t;
 #define PIN_SLPM_SHIFT		13
 #define PIN_SLPM_MASK		(0x1 << PIN_SLPM_SHIFT)
 #define PIN_SLPM(x)		(((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT)
-#define PIN_SLPM_INPUT		(NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT)
+#define PIN_SLPM_MAKE_INPUT	(NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT)
 #define PIN_SLPM_NOCHANGE	(NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT)
+/* These two replace the above in DB8500v2+ */
+#define PIN_SLPM_WAKEUP_ENABLE	(NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT)
+#define PIN_SLPM_WAKEUP_DISABLE	(NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT)
+
+#define PIN_DIR_SHIFT		14
+#define PIN_DIR_MASK		(0x1 << PIN_DIR_SHIFT)
+#define PIN_DIR(x)		(((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT)
+#define PIN_DIR_INPUT		(0 << PIN_DIR_SHIFT)
+#define PIN_DIR_OUTPUT		(1 << PIN_DIR_SHIFT)
+
+#define PIN_VAL_SHIFT		15
+#define PIN_VAL_MASK		(0x1 << PIN_VAL_SHIFT)
+#define PIN_VAL(x)		(((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT)
+#define PIN_VAL_LOW		(0 << PIN_VAL_SHIFT)
+#define PIN_VAL_HIGH		(1 << PIN_VAL_SHIFT)
+
+/* Shortcuts.  Use these instead of separate DIR and VAL.  */
+#define PIN_INPUT		PIN_DIR_INPUT
+#define PIN_OUTPUT_LOW		(PIN_DIR_OUTPUT | PIN_VAL_LOW)
+#define PIN_OUTPUT_HIGH		(PIN_DIR_OUTPUT | PIN_VAL_HIGH)
+
+/*
+ * These are the same as the ones above, but should make more sense to the
+ * reader when seen along with a setting a pin to AF mode.
+ */
+#define PIN_SLPM_INPUT		PIN_INPUT
+#define PIN_SLPM_OUTPUT_LOW	PIN_OUTPUT_LOW
+#define PIN_SLPM_OUTPUT_HIGH	PIN_OUTPUT_HIGH
 
 #define PIN_CFG_DEFAULT		(PIN_PULL_NONE | PIN_SLPM_INPUT)