Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
  MAINTAINERS: EB110ATX is not ebsa110
  MAINTAINERS: update Eric Miao's email address and status
  fb: add support of LCD display controller on pxa168/910 (base layer)
  [ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
  [ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
  [ARM] 5544/1: Trust PrimeCell resource sizes
  [ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
  [ARM] pxa/sharpsl_pm: drop set_irq_type calls
  [ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
  [ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
  [ARM] sa1100: remove unused collie_pm.c
  [ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
  [ARM] 5550/1: Add default configure file for w90p910 platform
  [ARM] 5549/1: Add clock api for w90p910 platform.
  [ARM] 5548/1: Add gpio api for w90p910 platform
  [ARM] 5551/1: Add multi-function pin api for w90p910 platform.
  [ARM] Make ARM_VIC_NR depend on ARM_VIC
  [ARM] 5546/1: ARM PL022 SSP/SPI driver v3
  ARM: OMAP4: SMP: Update defconfig for OMAP4430
  ARM: OMAP4: SMP: Enable SMP support for OMAP4430
  ...

1 files changed, 78 insertions, 5 deletions

diff --git a/arch/arm/plat-omap/include/mach/entry-macro.S b/arch/arm/plat-omap/include/mach/entry-macro.S
index 2276f89671d..56426ed45ef 100644
--- a/arch/arm/plat-omap/include/mach/entry-macro.S
+++ b/arch/arm/plat-omap/include/mach/entry-macro.S
@@ -3,6 +3,9 @@
  *
  * Low-level IRQ helper macros for OMAP-based platforms
  *
+ * Copyright (C) 2009 Texas Instruments
+ * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
  * This file is licensed under  the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
@@ -10,6 +13,7 @@
 #include <mach/hardware.h>
 #include <mach/io.h>
 #include <mach/irqs.h>
+#include <asm/hardware/gic.h>
 
 #if defined(CONFIG_ARCH_OMAP1)
 
@@ -56,15 +60,21 @@
 		.endm
 
 #endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
+#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
+			defined(CONFIG_ARCH_OMAP4)
 
-#if defined(CONFIG_ARCH_OMAP24XX)
 #include <mach/omap24xx.h>
-#endif
-#if defined(CONFIG_ARCH_OMAP34XX)
 #include <mach/omap34xx.h>
-#endif
 
+/* REVISIT: This should be set dynamically if CONFIG_MULTI_OMAP2 is selected */
+#if defined(CONFIG_ARCH_OMAP2420) || defined(CONFIG_ARCH_OMAP2430)
+#define OMAP2_VA_IC_BASE		IO_ADDRESS(OMAP24XX_IC_BASE)
+#elif defined(CONFIG_ARCH_OMAP34XX)
+#define OMAP2_VA_IC_BASE		IO_ADDRESS(OMAP34XX_IC_BASE)
+#endif
+#if defined(CONFIG_ARCH_OMAP4)
+#include <mach/omap44xx.h>
+#endif
 #define INTCPS_SIR_IRQ_OFFSET	0x0040		/* Active interrupt offset */
 #define	ACTIVEIRQ_MASK		0x7f		/* Active interrupt bits */
 
@@ -77,6 +87,7 @@
 		.macro  arch_ret_to_user, tmp1, tmp2
 		.endm
 
+#ifndef CONFIG_ARCH_OMAP4
 		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
 		ldr	\base, =OMAP2_VA_IC_BASE
 		ldr	\irqnr, [\base, #0x98] /* IRQ pending reg 1 */
@@ -92,6 +103,68 @@
 		and	\irqnr, \irqnr, #ACTIVEIRQ_MASK /* Clear spurious bits */
 
 		.endm
+#else
+		/*
+		 * The interrupt numbering scheme is defined in the
+		 * interrupt controller spec.  To wit:
+		 *
+		 * Interrupts 0-15 are IPI
+		 * 16-28 are reserved
+		 * 29-31 are local.  We allow 30 to be used for the watchdog.
+		 * 32-1020 are global
+		 * 1021-1022 are reserved
+		 * 1023 is "spurious" (no interrupt)
+		 *
+		 * For now, we ignore all local interrupts so only return an
+		 * interrupt if it's between 30 and 1020.  The test_for_ipi
+		 * routine below will pick up on IPIs.
+		 * A simple read from the controller will tell us the number
+		 * of the highest priority enabled interrupt.
+		 * We then just need to check whether it is in the
+		 * valid range for an IRQ (30-1020 inclusive).
+		 */
+		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
+		ldr     \base, =OMAP44XX_VA_GIC_CPU_BASE
+		ldr     \irqstat, [\base, #GIC_CPU_INTACK]
+
+		ldr     \tmp, =1021
+
+		bic     \irqnr, \irqstat, #0x1c00
+
+		cmp     \irqnr, #29
+		cmpcc   \irqnr, \irqnr
+		cmpne   \irqnr, \tmp
+		cmpcs   \irqnr, \irqnr
+		.endm
+
+		/* We assume that irqstat (the raw value of the IRQ acknowledge
+		 * register) is preserved from the macro above.
+		 * If there is an IPI, we immediately signal end of interrupt
+		 * on the controller, since this requires the original irqstat
+		 * value which we won't easily be able to recreate later.
+		 */
+
+		.macro test_for_ipi, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		cmp	\irqnr, #16
+		it	cc
+		strcc	\irqstat, [\base, #GIC_CPU_EOI]
+		it	cs
+		cmpcs	\irqnr, \irqnr
+		.endm
+
+		/* As above, this assumes that irqstat and base are preserved */
+
+		.macro test_for_ltirq, irqnr, irqstat, base, tmp
+		bic	\irqnr, \irqstat, #0x1c00
+		mov 	\tmp, #0
+		cmp	\irqnr, #29
+		itt	eq
+		moveq	\tmp, #1
+		streq	\irqstat, [\base, #GIC_CPU_EOI]
+		cmp	\tmp, #0
+		.endm
+#endif
 
 		.macro	irq_prio_table
 		.endm