Merge branch 'master' into for-next

Conflicts:
	arch/arm/mach-omap1/board-nokia770.c

20 files changed, 389 insertions, 354 deletions

diff --git a/arch/arm/plat-omap/include/plat/board.h b/arch/arm/plat-omap/include/plat/board.h
index 5cd622039da..3cf4fa25ab3 100644
--- a/arch/arm/plat-omap/include/plat/board.h
+++ b/arch/arm/plat-omap/include/plat/board.h
@@ -85,6 +85,14 @@ struct omap_usb_config {
 	 *  6 == 6 wire unidirectional (or TLL)
 	 */
 	u8		pins[3];
+
+	struct platform_device *udc_device;
+	struct platform_device *ohci_device;
+	struct platform_device *otg_device;
+
+	u32 (*usb0_init)(unsigned nwires, unsigned is_device);
+	u32 (*usb1_init)(unsigned nwires);
+	u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup);
 };
 
 struct omap_lcd_config {
diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h
index dfc472ca0cc..fef4696dcf6 100644
--- a/arch/arm/plat-omap/include/plat/clock.h
+++ b/arch/arm/plat-omap/include/plat/clock.h
@@ -19,6 +19,22 @@ struct module;
 struct clk;
 struct clockdomain;
 
+/**
+ * struct clkops - some clock function pointers
+ * @enable: fn ptr that enables the current clock in hardware
+ * @disable: fn ptr that enables the current clock in hardware
+ * @find_idlest: function returning the IDLEST register for the clock's IP blk
+ * @find_companion: function returning the "companion" clk reg for the clock
+ *
+ * A "companion" clk is an accompanying clock to the one being queried
+ * that must be enabled for the IP module connected to the clock to
+ * become accessible by the hardware.  Neither @find_idlest nor
+ * @find_companion should be needed; that information is IP
+ * block-specific; the hwmod code has been created to handle this, but
+ * until hwmod data is ready and drivers have been converted to use PM
+ * runtime calls in place of clk_enable()/clk_disable(), @find_idlest and
+ * @find_companion must, unfortunately, remain.
+ */
 struct clkops {
 	int			(*enable)(struct clk *);
 	void			(*disable)(struct clk *);
@@ -30,12 +46,45 @@ struct clkops {
 
 #ifdef CONFIG_ARCH_OMAP2PLUS
 
+/* struct clksel_rate.flags possibilities */
+#define RATE_IN_242X		(1 << 0)
+#define RATE_IN_243X		(1 << 1)
+#define RATE_IN_3XXX		(1 << 2)	/* rates common to all OMAP3 */
+#define RATE_IN_3430ES2		(1 << 3)	/* 3430ES2 rates only */
+#define RATE_IN_36XX		(1 << 4)
+#define RATE_IN_4430		(1 << 5)
+
+#define RATE_IN_24XX		(RATE_IN_242X | RATE_IN_243X)
+#define RATE_IN_3430ES2PLUS	(RATE_IN_3430ES2 | RATE_IN_36XX)
+
+/**
+ * struct clksel_rate - register bitfield values corresponding to clk divisors
+ * @val: register bitfield value (shifted to bit 0)
+ * @div: clock divisor corresponding to @val
+ * @flags: (see "struct clksel_rate.flags possibilities" above)
+ *
+ * @val should match the value of a read from struct clk.clksel_reg
+ * AND'ed with struct clk.clksel_mask, shifted right to bit 0.
+ *
+ * @div is the divisor that should be applied to the parent clock's rate
+ * to produce the current clock's rate.
+ *
+ * XXX @flags probably should be replaced with an struct omap_chip.
+ */
 struct clksel_rate {
 	u32			val;
 	u8			div;
 	u8			flags;
 };
 
+/**
+ * struct clksel - available parent clocks, and a pointer to their divisors
+ * @parent: struct clk * to a possible parent clock
+ * @rates: available divisors for this parent clock
+ *
+ * A struct clksel is always associated with one or more struct clks
+ * and one or more struct clksel_rates.
+ */
 struct clksel {
 	struct clk		 *parent;
 	const struct clksel_rate *rates;
@@ -116,6 +165,60 @@ struct dpll_data {
 
 #endif
 
+/* struct clk.flags possibilities */
+#define ENABLE_REG_32BIT	(1 << 0)	/* Use 32-bit access */
+#define CLOCK_IDLE_CONTROL	(1 << 1)
+#define CLOCK_NO_IDLE_PARENT	(1 << 2)
+#define ENABLE_ON_INIT		(1 << 3)	/* Enable upon framework init */
+#define INVERT_ENABLE		(1 << 4)	/* 0 enables, 1 disables */
+
+/**
+ * struct clk - OMAP struct clk
+ * @node: list_head connecting this clock into the full clock list
+ * @ops: struct clkops * for this clock
+ * @name: the name of the clock in the hardware (used in hwmod data and debug)
+ * @parent: pointer to this clock's parent struct clk
+ * @children: list_head connecting to the child clks' @sibling list_heads
+ * @sibling: list_head connecting this clk to its parent clk's @children
+ * @rate: current clock rate
+ * @enable_reg: register to write to enable the clock (see @enable_bit)
+ * @recalc: fn ptr that returns the clock's current rate
+ * @set_rate: fn ptr that can change the clock's current rate
+ * @round_rate: fn ptr that can round the clock's current rate
+ * @init: fn ptr to do clock-specific initialization
+ * @enable_bit: bitshift to write to enable/disable the clock (see @enable_reg)
+ * @usecount: number of users that have requested this clock to be enabled
+ * @fixed_div: when > 0, this clock's rate is its parent's rate / @fixed_div
+ * @flags: see "struct clk.flags possibilities" above
+ * @clksel_reg: for clksel clks, register va containing src/divisor select
+ * @clksel_mask: bitmask in @clksel_reg for the src/divisor selector
+ * @clksel: for clksel clks, pointer to struct clksel for this clock
+ * @dpll_data: for DPLLs, pointer to struct dpll_data for this clock
+ * @clkdm_name: clockdomain name that this clock is contained in
+ * @clkdm: pointer to struct clockdomain, resolved from @clkdm_name at runtime
+ * @rate_offset: bitshift for rate selection bitfield (OMAP1 only)
+ * @src_offset: bitshift for source selection bitfield (OMAP1 only)
+ *
+ * XXX @rate_offset, @src_offset should probably be removed and OMAP1
+ * clock code converted to use clksel.
+ *
+ * XXX @usecount is poorly named.  It should be "enable_count" or
+ * something similar.  "users" in the description refers to kernel
+ * code (core code or drivers) that have called clk_enable() and not
+ * yet called clk_disable(); the usecount of parent clocks is also
+ * incremented by the clock code when clk_enable() is called on child
+ * clocks and decremented by the clock code when clk_disable() is
+ * called on child clocks.
+ *
+ * XXX @clkdm, @usecount, @children, @sibling should be marked for
+ * internal use only.
+ *
+ * @children and @sibling are used to optimize parent-to-child clock
+ * tree traversals.  (child-to-parent traversals use @parent.)
+ *
+ * XXX The notion of the clock's current rate probably needs to be
+ * separated from the clock's target rate.
+ */
 struct clk {
 	struct list_head	node;
 	const struct clkops	*ops;
@@ -129,8 +232,8 @@ struct clk {
 	int			(*set_rate)(struct clk *, unsigned long);
 	long			(*round_rate)(struct clk *, unsigned long);
 	void			(*init)(struct clk *);
-	__u8			enable_bit;
-	__s8			usecount;
+	u8			enable_bit;
+	s8			usecount;
 	u8			fixed_div;
 	u8			flags;
 #ifdef CONFIG_ARCH_OMAP2PLUS
@@ -141,8 +244,8 @@ struct clk {
 	const char		*clkdm_name;
 	struct clockdomain	*clkdm;
 #else
-	__u8			rate_offset;
-	__u8			src_offset;
+	u8			rate_offset;
+	u8			src_offset;
 #endif
 #if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS)
 	struct dentry		*dent;	/* For visible tree hierarchy */
@@ -188,23 +291,4 @@ extern const struct clkops clkops_null;
 
 extern struct clk dummy_ck;
 
-/* Clock flags */
-#define ENABLE_REG_32BIT	(1 << 0)	/* Use 32-bit access */
-#define CLOCK_IDLE_CONTROL	(1 << 1)
-#define CLOCK_NO_IDLE_PARENT	(1 << 2)
-#define ENABLE_ON_INIT		(1 << 3)	/* Enable upon framework init */
-#define INVERT_ENABLE		(1 << 4)	/* 0 enables, 1 disables */
-
-/* Clksel_rate flags */
-#define RATE_IN_242X		(1 << 0)
-#define RATE_IN_243X		(1 << 1)
-#define RATE_IN_3XXX		(1 << 2)	/* rates common to all OMAP3 */
-#define RATE_IN_3430ES2		(1 << 3)	/* 3430ES2 rates only */
-#define RATE_IN_36XX		(1 << 4)
-#define RATE_IN_4430		(1 << 5)
-
-#define RATE_IN_24XX		(RATE_IN_242X | RATE_IN_243X)
-
-#define RATE_IN_3430ES2PLUS	(RATE_IN_3430ES2 | RATE_IN_36XX)
-
 #endif
diff --git a/arch/arm/plat-omap/include/plat/common.h b/arch/arm/plat-omap/include/plat/common.h
index 5e4afbee0fd..9776b41ad76 100644
--- a/arch/arm/plat-omap/include/plat/common.h
+++ b/arch/arm/plat-omap/include/plat/common.h
@@ -58,8 +58,7 @@ struct omap_globals {
 
 void omap2_set_globals_242x(void);
 void omap2_set_globals_243x(void);
-void omap2_set_globals_343x(void);
-void omap2_set_globals_36xx(void);
+void omap2_set_globals_3xxx(void);
 void omap2_set_globals_443x(void);
 
 /* These get called from omap2_set_globals_xxxx(), do not call these */
@@ -69,6 +68,8 @@ void omap2_set_globals_control(struct omap_globals *);
 void omap2_set_globals_prcm(struct omap_globals *);
 void omap2_set_globals_uart(struct omap_globals *);
 
+void omap3_map_io(void);
+
 /**
  * omap_test_timeout - busy-loop, testing a condition
  * @cond: condition to test until it evaluates to true
@@ -89,4 +90,8 @@ void omap2_set_globals_uart(struct omap_globals *);
 	}							\
 })
 
+extern struct device *omap2_get_mpuss_device(void);
+extern struct device *omap2_get_dsp_device(void);
+extern struct device *omap2_get_l3_device(void);
+
 #endif /* __ARCH_ARM_MACH_OMAP_COMMON_H */
diff --git a/arch/arm/plat-omap/include/plat/cpu.h b/arch/arm/plat-omap/include/plat/cpu.h
index 75141742300..2e2ae530fce 100644
--- a/arch/arm/plat-omap/include/plat/cpu.h
+++ b/arch/arm/plat-omap/include/plat/cpu.h
@@ -66,6 +66,8 @@ unsigned int omap_rev(void);
  * family. This difference can be handled separately.
  */
 #define OMAP_REVBITS_00		0x00
+#define OMAP_REVBITS_01		0x01
+#define OMAP_REVBITS_02		0x02
 #define OMAP_REVBITS_10		0x10
 #define OMAP_REVBITS_20		0x20
 #define OMAP_REVBITS_30		0x30
@@ -376,6 +378,8 @@ IS_OMAP_TYPE(3517, 0x3517)
 #define OMAP3430_REV_ES3_1_2	0x34305034
 
 #define OMAP3630_REV_ES1_0	0x36300034
+#define OMAP3630_REV_ES1_1	0x36300134
+#define OMAP3630_REV_ES1_2	0x36300234
 
 #define OMAP35XX_CLASS		0x35000034
 #define OMAP3503_REV(v)		(OMAP35XX_CLASS | (0x3503 << 16) | (v << 8))
@@ -411,6 +415,8 @@ IS_OMAP_TYPE(3517, 0x3517)
 #define CHIP_IS_OMAP3430ES3_1		(1 << 6)
 #define CHIP_IS_OMAP3630ES1		(1 << 7)
 #define CHIP_IS_OMAP4430ES1		(1 << 8)
+#define CHIP_IS_OMAP3630ES1_1           (1 << 9)
+#define CHIP_IS_OMAP3630ES1_2           (1 << 10)
 
 #define CHIP_IS_OMAP24XX		(CHIP_IS_OMAP2420 | CHIP_IS_OMAP2430)
 
@@ -424,11 +430,12 @@ IS_OMAP_TYPE(3517, 0x3517)
  */
 #define CHIP_GE_OMAP3430ES2		(CHIP_IS_OMAP3430ES2 | \
 					 CHIP_IS_OMAP3430ES3_0 | \
-					 CHIP_IS_OMAP3430ES3_1 | \
-					 CHIP_IS_OMAP3630ES1)
+					 CHIP_GE_OMAP3430ES3_1)
 #define CHIP_GE_OMAP3430ES3_1		(CHIP_IS_OMAP3430ES3_1 | \
-					 CHIP_IS_OMAP3630ES1)
-
+					 CHIP_IS_OMAP3630ES1 | \
+					 CHIP_GE_OMAP3630ES1_1)
+#define CHIP_GE_OMAP3630ES1_1		(CHIP_IS_OMAP3630ES1_1 | \
+					 CHIP_IS_OMAP3630ES1_2)
 
 int omap_chip_is(struct omap_chip_id oci);
 void omap2_check_revision(void);
@@ -444,6 +451,7 @@ extern u32 omap3_features;
 #define OMAP3_HAS_NEON			BIT(3)
 #define OMAP3_HAS_ISP			BIT(4)
 #define OMAP3_HAS_192MHZ_CLK		BIT(5)
+#define OMAP3_HAS_IO_WAKEUP		BIT(6)
 
 #define OMAP3_HAS_FEATURE(feat,flag)			\
 static inline unsigned int omap3_has_ ##feat(void)	\
@@ -457,5 +465,6 @@ OMAP3_HAS_FEATURE(iva, IVA)
 OMAP3_HAS_FEATURE(neon, NEON)
 OMAP3_HAS_FEATURE(isp, ISP)
 OMAP3_HAS_FEATURE(192mhz_clk, 192MHZ_CLK)
+OMAP3_HAS_FEATURE(io_wakeup, IO_WAKEUP)
 
 #endif
diff --git a/arch/arm/plat-omap/include/plat/display.h b/arch/arm/plat-omap/include/plat/display.h
index 1c529ce9dc1..8bd15bdb413 100644
--- a/arch/arm/plat-omap/include/plat/display.h
+++ b/arch/arm/plat-omap/include/plat/display.h
@@ -238,7 +238,7 @@ int dsi_vc_dcs_write_1(int channel, u8 dcs_cmd, u8 param);
 int dsi_vc_dcs_write_nosync(int channel, u8 *data, int len);
 int dsi_vc_dcs_read(int channel, u8 dcs_cmd, u8 *buf, int buflen);
 int dsi_vc_dcs_read_1(int channel, u8 dcs_cmd, u8 *data);
-int dsi_vc_dcs_read_2(int channel, u8 dcs_cmd, u16 *data);
+int dsi_vc_dcs_read_2(int channel, u8 dcs_cmd, u8 *data1, u8 *data2);
 int dsi_vc_set_max_rx_packet_size(int channel, u16 len);
 int dsi_vc_send_null(int channel);
 int dsi_vc_send_bta_sync(int channel);
@@ -277,8 +277,8 @@ struct omap_video_timings {
  * identify the mode, and does not actually use the configs
  * itself. However, the configs should be something that
  * a normal monitor can also show */
-const extern struct omap_video_timings omap_dss_pal_timings;
-const extern struct omap_video_timings omap_dss_ntsc_timings;
+extern const struct omap_video_timings omap_dss_pal_timings;
+extern const struct omap_video_timings omap_dss_ntsc_timings;
 #endif
 
 struct omap_overlay_info {
@@ -560,7 +560,8 @@ void omapdss_dsi_vc_enable_hs(int channel, bool enable);
 int omapdss_dsi_enable_te(struct omap_dss_device *dssdev, bool enable);
 
 int omap_dsi_prepare_update(struct omap_dss_device *dssdev,
-				    u16 *x, u16 *y, u16 *w, u16 *h);
+				    u16 *x, u16 *y, u16 *w, u16 *h,
+				    bool enlarge_update_area);
 int omap_dsi_update(struct omap_dss_device *dssdev,
 		int channel,
 		u16 x, u16 y, u16 w, u16 h,
diff --git a/arch/arm/plat-omap/include/plat/dma.h b/arch/arm/plat-omap/include/plat/dma.h
index 02232ca2c37..af3a03941ad 100644
--- a/arch/arm/plat-omap/include/plat/dma.h
+++ b/arch/arm/plat-omap/include/plat/dma.h
@@ -345,6 +345,7 @@
 #define OMAP_DMA_SYNC_BLOCK		0x02
 #define OMAP_DMA_SYNC_PACKET		0x03
 
+#define OMAP_DMA_DST_SYNC_PREFETCH	0x02
 #define OMAP_DMA_SRC_SYNC		0x01
 #define OMAP_DMA_DST_SYNC		0x00
 
diff --git a/arch/arm/plat-omap/include/plat/dsp_common.h b/arch/arm/plat-omap/include/plat/dsp_common.h
deleted file mode 100644
index da97736f3ef..00000000000
--- a/arch/arm/plat-omap/include/plat/dsp_common.h
+++ /dev/null
@@ -1,40 +0,0 @@
-/*
- * This file is part of OMAP DSP driver (DSP Gateway version 3.3.1)
- *
- * Copyright (C) 2004-2006 Nokia Corporation. All rights reserved.
- *
- * Contact: Toshihiro Kobayashi <toshihiro.kobayashi@nokia.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#ifndef ASM_ARCH_DSP_COMMON_H
-#define ASM_ARCH_DSP_COMMON_H
-
-#if defined(CONFIG_ARCH_OMAP1) && defined(CONFIG_OMAP_MMU_FWK)
-extern void omap_dsp_request_mpui(void);
-extern void omap_dsp_release_mpui(void);
-extern int omap_dsp_request_mem(void);
-extern int omap_dsp_release_mem(void);
-#else
-static inline int omap_dsp_request_mem(void)
-{
-	return 0;
-}
-#define omap_dsp_release_mem()	do {} while (0)
-#endif
-
-#endif /* ASM_ARCH_DSP_COMMON_H */
diff --git a/arch/arm/plat-omap/include/plat/gpmc.h b/arch/arm/plat-omap/include/plat/gpmc.h
index 145838a81ef..9fd99b9e40a 100644
--- a/arch/arm/plat-omap/include/plat/gpmc.h
+++ b/arch/arm/plat-omap/include/plat/gpmc.h
@@ -25,10 +25,26 @@
 #define GPMC_CS_NAND_ADDRESS	0x20
 #define GPMC_CS_NAND_DATA	0x24
 
-#define GPMC_CONFIG		0x50
-#define GPMC_STATUS		0x54
-#define GPMC_CS0_BASE		0x60
-#define GPMC_CS_SIZE		0x30
+/* Control Commands */
+#define GPMC_CONFIG_RDY_BSY	0x00000001
+#define GPMC_CONFIG_DEV_SIZE	0x00000002
+#define GPMC_CONFIG_DEV_TYPE	0x00000003
+#define GPMC_SET_IRQ_STATUS	0x00000004
+#define GPMC_CONFIG_WP		0x00000005
+
+#define GPMC_GET_IRQ_STATUS	0x00000006
+#define GPMC_PREFETCH_FIFO_CNT	0x00000007 /* bytes available in FIFO for r/w */
+#define GPMC_PREFETCH_COUNT	0x00000008 /* remaining bytes to be read/write*/
+#define GPMC_STATUS_BUFFER	0x00000009 /* 1: buffer is available to write */
+
+#define GPMC_NAND_COMMAND	0x0000000a
+#define GPMC_NAND_ADDRESS	0x0000000b
+#define GPMC_NAND_DATA		0x0000000c
+
+/* ECC commands */
+#define GPMC_ECC_READ		0 /* Reset Hardware ECC for read */
+#define GPMC_ECC_WRITE		1 /* Reset Hardware ECC for write */
+#define GPMC_ECC_READSYN	2 /* Reset before syndrom is read back */
 
 #define GPMC_CONFIG1_WRAPBURST_SUPP     (1 << 31)
 #define GPMC_CONFIG1_READMULTIPLE_SUPP  (1 << 30)
@@ -47,7 +63,6 @@
 #define GPMC_CONFIG1_DEVICESIZE_16      GPMC_CONFIG1_DEVICESIZE(1)
 #define GPMC_CONFIG1_DEVICETYPE(val)    ((val & 3) << 10)
 #define GPMC_CONFIG1_DEVICETYPE_NOR     GPMC_CONFIG1_DEVICETYPE(0)
-#define GPMC_CONFIG1_DEVICETYPE_NAND    GPMC_CONFIG1_DEVICETYPE(2)
 #define GPMC_CONFIG1_MUXADDDATA         (1 << 9)
 #define GPMC_CONFIG1_TIME_PARA_GRAN     (1 << 4)
 #define GPMC_CONFIG1_FCLK_DIV(val)      (val & 3)
@@ -56,6 +71,14 @@
 #define GPMC_CONFIG1_FCLK_DIV4          (GPMC_CONFIG1_FCLK_DIV(3))
 #define GPMC_CONFIG7_CSVALID		(1 << 6)
 
+#define GPMC_DEVICETYPE_NOR		0
+#define GPMC_DEVICETYPE_NAND		2
+#define GPMC_CONFIG_WRITEPROTECT	0x00000010
+#define GPMC_STATUS_BUFF_EMPTY		0x00000001
+#define WR_RD_PIN_MONITORING		0x00600000
+#define GPMC_PREFETCH_STATUS_FIFO_CNT(val)	((val >> 24) & 0x7F)
+#define GPMC_PREFETCH_STATUS_COUNT(val)	(val & 0x00003fff)
+
 /*
  * Note that all values in this struct are in nanoseconds, while
  * the register values are in gpmc_fck cycles.
@@ -108,10 +131,15 @@ extern int gpmc_cs_set_reserved(int cs, int reserved);
 extern int gpmc_cs_reserved(int cs);
 extern int gpmc_prefetch_enable(int cs, int dma_mode,
 					unsigned int u32_count, int is_write);
-extern void gpmc_prefetch_reset(void);
-extern int gpmc_prefetch_status(void);
+extern int gpmc_prefetch_reset(int cs);
 extern void omap3_gpmc_save_context(void);
 extern void omap3_gpmc_restore_context(void);
 extern void gpmc_init(void);
+extern int gpmc_read_status(int cmd);
+extern int gpmc_cs_configure(int cs, int cmd, int wval);
+extern int gpmc_nand_read(int cs, int cmd);
+extern int gpmc_nand_write(int cs, int cmd, int wval);
 
+int gpmc_enable_hwecc(int cs, int mode, int dev_width, int ecc_size);
+int gpmc_calculate_ecc(int cs, const u_char *dat, u_char *ecc_code);
 #endif
diff --git a/arch/arm/plat-omap/include/plat/iommu.h b/arch/arm/plat-omap/include/plat/iommu.h
index 0752af9d099..33c7d41cb6a 100644
--- a/arch/arm/plat-omap/include/plat/iommu.h
+++ b/arch/arm/plat-omap/include/plat/iommu.h
@@ -80,6 +80,7 @@ struct iommu_functions {
 
 	int (*enable)(struct iommu *obj);
 	void (*disable)(struct iommu *obj);
+	void (*set_twl)(struct iommu *obj, bool on);
 	u32 (*fault_isr)(struct iommu *obj, u32 *ra);
 
 	void (*tlb_read_cr)(struct iommu *obj, struct cr_regs *cr);
@@ -143,6 +144,7 @@ extern void iotlb_cr_to_e(struct cr_regs *cr, struct iotlb_entry *e);
 extern u32 iotlb_cr_to_virt(struct cr_regs *cr);
 
 extern int load_iotlb_entry(struct iommu *obj, struct iotlb_entry *e);
+extern void iommu_set_twl(struct iommu *obj, bool on);
 extern void flush_iotlb_page(struct iommu *obj, u32 da);
 extern void flush_iotlb_range(struct iommu *obj, u32 start, u32 end);
 extern void flush_iotlb_all(struct iommu *obj);
diff --git a/arch/arm/plat-omap/include/plat/mailbox.h b/arch/arm/plat-omap/include/plat/mailbox.h
index 729166b76a7..99765655210 100644
--- a/arch/arm/plat-omap/include/plat/mailbox.h
+++ b/arch/arm/plat-omap/include/plat/mailbox.h
@@ -3,10 +3,11 @@
 #ifndef MAILBOX_H
 #define MAILBOX_H
 
-#include <linux/wait.h>
+#include <linux/spinlock.h>
 #include <linux/workqueue.h>
-#include <linux/blkdev.h>
 #include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/kfifo.h>
 
 typedef u32 mbox_msg_t;
 struct omap_mbox;
@@ -42,7 +43,7 @@ struct omap_mbox_ops {
 
 struct omap_mbox_queue {
 	spinlock_t		lock;
-	struct request_queue	*queue;
+	struct kfifo		fifo;
 	struct work_struct	work;
 	struct tasklet_struct	tasklet;
 	int	(*callback)(void *);
@@ -52,19 +53,10 @@ struct omap_mbox_queue {
 struct omap_mbox {
 	char			*name;
 	unsigned int		irq;
-
 	struct omap_mbox_queue	*txq, *rxq;
-
 	struct omap_mbox_ops	*ops;
-
-	mbox_msg_t		seq_snd, seq_rcv;
-
 	struct device		*dev;
-
-	struct omap_mbox	*next;
 	void			*priv;
-
-	void			(*err_notify)(void);
 };
 
 int omap_mbox_msg_send(struct omap_mbox *, mbox_msg_t msg);
@@ -73,8 +65,8 @@ void omap_mbox_init_seq(struct omap_mbox *);
 struct omap_mbox *omap_mbox_get(const char *);
 void omap_mbox_put(struct omap_mbox *);
 
-int omap_mbox_register(struct device *parent, struct omap_mbox *);
-int omap_mbox_unregister(struct omap_mbox *);
+int omap_mbox_register(struct device *parent, struct omap_mbox **);
+int omap_mbox_unregister(void);
 
 static inline void omap_mbox_save_ctx(struct omap_mbox *mbox)
 {
diff --git a/arch/arm/plat-omap/include/plat/mcbsp.h b/arch/arm/plat-omap/include/plat/mcbsp.h
index 975744f10a5..b4ff6a11a8f 100644
--- a/arch/arm/plat-omap/include/plat/mcbsp.h
+++ b/arch/arm/plat-omap/include/plat/mcbsp.h
@@ -473,6 +473,7 @@ void omap_mcbsp_set_tx_threshold(unsigned int id, u16 threshold);
 void omap_mcbsp_set_rx_threshold(unsigned int id, u16 threshold);
 u16 omap_mcbsp_get_max_tx_threshold(unsigned int id);
 u16 omap_mcbsp_get_max_rx_threshold(unsigned int id);
+u16 omap_mcbsp_get_fifo_size(unsigned int id);
 u16 omap_mcbsp_get_tx_delay(unsigned int id);
 u16 omap_mcbsp_get_rx_delay(unsigned int id);
 int omap_mcbsp_get_dma_op_mode(unsigned int id);
@@ -483,6 +484,7 @@ static inline void omap_mcbsp_set_rx_threshold(unsigned int id, u16 threshold)
 { }
 static inline u16 omap_mcbsp_get_max_tx_threshold(unsigned int id) { return 0; }
 static inline u16 omap_mcbsp_get_max_rx_threshold(unsigned int id) { return 0; }
+static inline u16 omap_mcbsp_get_fifo_size(unsigned int id) { return 0; }
 static inline u16 omap_mcbsp_get_tx_delay(unsigned int id) { return 0; }
 static inline u16 omap_mcbsp_get_rx_delay(unsigned int id) { return 0; }
 static inline int omap_mcbsp_get_dma_op_mode(unsigned int id) { return 0; }
diff --git a/arch/arm/plat-omap/include/plat/mux.h b/arch/arm/plat-omap/include/plat/mux.h
index c7472a28ce2..aeba71796ad 100644
--- a/arch/arm/plat-omap/include/plat/mux.h
+++ b/arch/arm/plat-omap/include/plat/mux.h
@@ -114,28 +114,11 @@
 	PU_PD_REG(NA, 0)		\
 },
 
-#define MUX_CFG_24XX(desc, reg_offset, mode,			\
-				pull_en, pull_mode, dbg)	\
-{								\
-	.name		= desc,					\
-	.debug		= dbg,					\
-	.mux_reg	= reg_offset,				\
-	.mask		= mode,					\
-	.pull_val	= pull_en,				\
-	.pu_pd_val	= pull_mode,				\
-},
-
-/* 24xx/34xx mux bit defines */
-#define OMAP2_PULL_ENA		(1 << 3)
-#define OMAP2_PULL_UP		(1 << 4)
-#define OMAP2_ALTELECTRICALSEL	(1 << 5)
-
 struct pin_config {
 	char 			*name;
 	const unsigned int 	mux_reg;
 	unsigned char		debug;
 
-#if	defined(CONFIG_ARCH_OMAP1) || defined(CONFIG_ARCH_OMAP2)
 	const unsigned char mask_offset;
 	const unsigned char mask;
 
@@ -147,7 +130,6 @@ struct pin_config {
 	const char *pu_pd_name;
 	const unsigned int pu_pd_reg;
 	const unsigned char pu_pd_val;
-#endif
 
 #if	defined(CONFIG_OMAP_MUX_DEBUG) || defined(CONFIG_OMAP_MUX_WARNINGS)
 	const char *mux_reg_name;
@@ -191,6 +173,10 @@ enum omap7xx_index {
 	SPI_7XX_4,
 	SPI_7XX_5,
 	SPI_7XX_6,
+
+	/* UART */
+	UART_7XX_1,
+	UART_7XX_2,
 };
 
 enum omap1xxx_index {
@@ -446,208 +432,6 @@ enum omap1xxx_index {
 
 };
 
-enum omap24xx_index {
-	/* 24xx I2C */
-	M19_24XX_I2C1_SCL,
-	L15_24XX_I2C1_SDA,
-	J15_24XX_I2C2_SCL,
-	H19_24XX_I2C2_SDA,
-
-	/* 24xx Menelaus interrupt */
-	W19_24XX_SYS_NIRQ,
-
-	/* 24xx clock */
-	W14_24XX_SYS_CLKOUT,
-
-	/* 24xx GPMC chipselects, wait pin monitoring */
-	E2_GPMC_NCS2,
-	L2_GPMC_NCS7,
-	L3_GPMC_WAIT0,
-	N7_GPMC_WAIT1,
-	M1_GPMC_WAIT2,
-	P1_GPMC_WAIT3,
-
-	/* 242X McBSP */
-	Y15_24XX_MCBSP2_CLKX,
-	R14_24XX_MCBSP2_FSX,
-	W15_24XX_MCBSP2_DR,
-	V15_24XX_MCBSP2_DX,
-
-	/* 24xx GPIO */
-	M21_242X_GPIO11,
-	P21_242X_GPIO12,
-	AA10_242X_GPIO13,
-	AA6_242X_GPIO14,
-	AA4_242X_GPIO15,
-	Y11_242X_GPIO16,
-	AA12_242X_GPIO17,
-	AA8_242X_GPIO58,
-	Y20_24XX_GPIO60,
-	W4__24XX_GPIO74,
-	N15_24XX_GPIO85,
-	M15_24XX_GPIO92,
-	P20_24XX_GPIO93,
-	P18_24XX_GPIO95,
-	M18_24XX_GPIO96,
-	L14_24XX_GPIO97,
-	J15_24XX_GPIO99,
-	V14_24XX_GPIO117,
-	P14_24XX_GPIO125,
-
-	/* 242x DBG GPIO */
-	V4_242X_GPIO49,
-	W2_242X_GPIO50,
-	U4_242X_GPIO51,
-	V3_242X_GPIO52,
-	V2_242X_GPIO53,
-	V6_242X_GPIO53,
-	T4_242X_GPIO54,
-	Y4_242X_GPIO54,
-	T3_242X_GPIO55,
-	U2_242X_GPIO56,
-
-	/* 24xx external DMA requests */
-	AA10_242X_DMAREQ0,
-	AA6_242X_DMAREQ1,
-	E4_242X_DMAREQ2,
-	G4_242X_DMAREQ3,
-	D3_242X_DMAREQ4,
-	E3_242X_DMAREQ5,
-
-	/* UART3 */
-	K15_24XX_UART3_TX,
-	K14_24XX_UART3_RX,
-
-	/* MMC/SDIO */
-	G19_24XX_MMC_CLKO,
-	H18_24XX_MMC_CMD,
-	F20_24XX_MMC_DAT0,
-	H14_24XX_MMC_DAT1,
-	E19_24XX_MMC_DAT2,
-	D19_24XX_MMC_DAT3,
-	F19_24XX_MMC_DAT_DIR0,
-	E20_24XX_MMC_DAT_DIR1,
-	F18_24XX_MMC_DAT_DIR2,
-	E18_24XX_MMC_DAT_DIR3,
-	G18_24XX_MMC_CMD_DIR,
-	H15_24XX_MMC_CLKI,
-
-	/* Full speed USB */
-	J20_24XX_USB0_PUEN,
-	J19_24XX_USB0_VP,
-	K20_24XX_USB0_VM,
-	J18_24XX_USB0_RCV,
-	K19_24XX_USB0_TXEN,
-	J14_24XX_USB0_SE0,
-	K18_24XX_USB0_DAT,
-
-	N14_24XX_USB1_SE0,
-	W12_24XX_USB1_SE0,
-	P15_24XX_USB1_DAT,
-	R13_24XX_USB1_DAT,
-	W20_24XX_USB1_TXEN,
-	P13_24XX_USB1_TXEN,
-	V19_24XX_USB1_RCV,
-	V12_24XX_USB1_RCV,
-
-	AA10_24XX_USB2_SE0,
-	Y11_24XX_USB2_DAT,
-	AA12_24XX_USB2_TXEN,
-	AA6_24XX_USB2_RCV,
-	AA4_24XX_USB2_TLLSE0,
-
-	/* Keypad GPIO*/
-	T19_24XX_KBR0,
-	R19_24XX_KBR1,
-	V18_24XX_KBR2,
-	M21_24XX_KBR3,
-	E5__24XX_KBR4,
-	M18_24XX_KBR5,
-	R20_24XX_KBC0,
-	M14_24XX_KBC1,
-	H19_24XX_KBC2,
-	V17_24XX_KBC3,
-	P21_24XX_KBC4,
-	L14_24XX_KBC5,
-	N19_24XX_KBC6,
-
-	/* 24xx Menelaus Keypad GPIO */
-	B3__24XX_KBR5,
-	AA4_24XX_KBC2,
-	B13_24XX_KBC6,
-
-	/* 2430 USB */
-	AD9_2430_USB0_PUEN,
-	Y11_2430_USB0_VP,
-	AD7_2430_USB0_VM,
-	AE7_2430_USB0_RCV,
-	AD4_2430_USB0_TXEN,
-	AF9_2430_USB0_SE0,
-	AE6_2430_USB0_DAT,
-	AD24_2430_USB1_SE0,
-	AB24_2430_USB1_RCV,
-	Y25_2430_USB1_TXEN,
-	AA26_2430_USB1_DAT,
-
-	/* 2430 HS-USB */
-	AD9_2430_USB0HS_DATA3,
-	Y11_2430_USB0HS_DATA4,
-	AD7_2430_USB0HS_DATA5,
-	AE7_2430_USB0HS_DATA6,
-	AD4_2430_USB0HS_DATA2,
-	AF9_2430_USB0HS_DATA0,
-	AE6_2430_USB0HS_DATA1,
-	AE8_2430_USB0HS_CLK,
-	AD8_2430_USB0HS_DIR,
-	AE5_2430_USB0HS_STP,
-	AE9_2430_USB0HS_NXT,
-	AC7_2430_USB0HS_DATA7,
-
-	/* 2430 McBSP */
-	AD6_2430_MCBSP_CLKS,
-
-	AB2_2430_MCBSP1_CLKR,
-	AD5_2430_MCBSP1_FSR,
-	AA1_2430_MCBSP1_DX,
-	AF3_2430_MCBSP1_DR,
-	AB3_2430_MCBSP1_FSX,
-	Y9_2430_MCBSP1_CLKX,
-
-	AC10_2430_MCBSP2_FSX,
-	AD16_2430_MCBSP2_CLX,
-	AE13_2430_MCBSP2_DX,
-	AD13_2430_MCBSP2_DR,
-	AC10_2430_MCBSP2_FSX_OFF,
-	AD16_2430_MCBSP2_CLX_OFF,
-	AE13_2430_MCBSP2_DX_OFF,
-	AD13_2430_MCBSP2_DR_OFF,
-
-	AC9_2430_MCBSP3_CLKX,
-	AE4_2430_MCBSP3_FSX,
-	AE2_2430_MCBSP3_DR,
-	AF4_2430_MCBSP3_DX,
-
-	N3_2430_MCBSP4_CLKX,
-	AD23_2430_MCBSP4_DR,
-	AB25_2430_MCBSP4_DX,
-	AC25_2430_MCBSP4_FSX,
-
-	AE16_2430_MCBSP5_CLKX,
-	AF12_2430_MCBSP5_FSX,
-	K7_2430_MCBSP5_DX,
-	M1_2430_MCBSP5_DR,
-
-	/* 2430 McSPI*/
-	Y18_2430_MCSPI1_CLK,
-	AD15_2430_MCSPI1_SIMO,
-	AE17_2430_MCSPI1_SOMI,
-	U1_2430_MCSPI1_CS0,
-
-	/* Touchscreen GPIO */
-	AF19_2430_GPIO_85,
-
-};
-
 struct omap_mux_cfg {
 	struct pin_config	*pins;
 	unsigned long		size;
diff --git a/arch/arm/plat-omap/include/plat/nand.h b/arch/arm/plat-omap/include/plat/nand.h
index f8efd5466b1..6562cd082bb 100644
--- a/arch/arm/plat-omap/include/plat/nand.h
+++ b/arch/arm/plat-omap/include/plat/nand.h
@@ -21,13 +21,11 @@ struct omap_nand_platform_data {
 	int			(*dev_ready)(struct omap_nand_platform_data *);
 	int			dma_channel;
 	unsigned long		phys_base;
-	void __iomem		*gpmc_cs_baseaddr;
-	void __iomem		*gpmc_baseaddr;
 	int			devsize;
 };
 
-/* size (4 KiB) for IO mapping */
-#define	NAND_IO_SIZE	SZ_4K
+/* minimum size for IO mapping */
+#define	NAND_IO_SIZE	4
 
 #if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
 extern int gpmc_nand_init(struct omap_nand_platform_data *d);
diff --git a/arch/arm/plat-omap/include/plat/nokia-dsi-panel.h b/arch/arm/plat-omap/include/plat/nokia-dsi-panel.h
new file mode 100644
index 00000000000..01ab6572ccb
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/nokia-dsi-panel.h
@@ -0,0 +1,31 @@
+#ifndef __ARCH_ARM_PLAT_OMAP_NOKIA_DSI_PANEL_H
+#define __ARCH_ARM_PLAT_OMAP_NOKIA_DSI_PANEL_H
+
+#include "display.h"
+
+/**
+ * struct nokia_dsi_panel_data - Nokia DSI panel driver configuration
+ * @name: panel name
+ * @use_ext_te: use external TE
+ * @ext_te_gpio: external TE GPIO
+ * @use_esd_check: perform ESD checks
+ * @max_backlight_level: maximum backlight level
+ * @set_backlight: pointer to backlight set function
+ * @get_backlight: pointer to backlight get function
+ */
+struct nokia_dsi_panel_data {
+	const char *name;
+
+	int reset_gpio;
+
+	bool use_ext_te;
+	int ext_te_gpio;
+
+	bool use_esd_check;
+
+	int max_backlight_level;
+	int (*set_backlight)(struct omap_dss_device *dssdev, int level);
+	int (*get_backlight)(struct omap_dss_device *dssdev);
+};
+
+#endif /* __ARCH_ARM_PLAT_OMAP_NOKIA_DSI_PANEL_H */
diff --git a/arch/arm/plat-omap/include/plat/omap-pm.h b/arch/arm/plat-omap/include/plat/omap-pm.h
index 3ee41d71149..728fbb9dd54 100644
--- a/arch/arm/plat-omap/include/plat/omap-pm.h
+++ b/arch/arm/plat-omap/include/plat/omap-pm.h
@@ -1,8 +1,8 @@
 /*
  * omap-pm.h - OMAP power management interface
  *
- * Copyright (C) 2008-2009 Texas Instruments, Inc.
- * Copyright (C) 2008-2009 Nokia Corporation
+ * Copyright (C) 2008-2010 Texas Instruments, Inc.
+ * Copyright (C) 2008-2010 Nokia Corporation
  * Paul Walmsley
  *
  * Interface developed by (in alphabetical order): Karthik Dasu, Jouni
@@ -16,6 +16,7 @@
 
 #include <linux/device.h>
 #include <linux/cpufreq.h>
+#include <linux/clk.h>
 
 #include "powerdomain.h"
 
@@ -89,7 +90,7 @@ void omap_pm_if_exit(void);
  * @t: maximum MPU wakeup latency in microseconds
  *
  * Request that the maximum interrupt latency for the MPU to be no
- * greater than 't' microseconds. "Interrupt latency" in this case is
+ * greater than @t microseconds. "Interrupt latency" in this case is
  * defined as the elapsed time from the occurrence of a hardware or
  * timer interrupt to the time when the device driver's interrupt
  * service routine has been entered by the MPU.
@@ -105,15 +106,19 @@ void omap_pm_if_exit(void);
  * elapsed from when a device driver enables a hardware device with
  * clk_enable(), to when the device is ready for register access or
  * other use.  To control this device wakeup latency, use
- * set_max_dev_wakeup_lat()
+ * omap_pm_set_max_dev_wakeup_lat()
  *
- * Multiple calls to set_max_mpu_wakeup_lat() will replace the
+ * Multiple calls to omap_pm_set_max_mpu_wakeup_lat() will replace the
  * previous t value.  To remove the latency target for the MPU, call
  * with t = -1.
  *
- * No return value.
+ * XXX This constraint will be deprecated soon in favor of the more
+ * general omap_pm_set_max_dev_wakeup_lat()
+ *
+ * Returns -EINVAL for an invalid argument, -ERANGE if the constraint
+ * is not satisfiable, or 0 upon success.
  */
-void omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t);
+int omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t);
 
 
 /**
@@ -123,8 +128,8 @@ void omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t);
  * @r: minimum throughput (in KiB/s)
  *
  * Request that the minimum data throughput on the OCP interconnect
- * attached to device 'dev' interconnect agent 'tbus_id' be no less
- * than 'r' KiB/s.
+ * attached to device @dev interconnect agent @tbus_id be no less
+ * than @r KiB/s.
  *
  * It is expected that the OMAP PM or bus code will use this
  * information to set the interconnect clock to run at the lowest
@@ -138,40 +143,44 @@ void omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t);
  * code will also need to add an minimum L3 interconnect speed
  * constraint,
  *
- * Multiple calls to set_min_bus_tput() will replace the previous rate
- * value for this device.  To remove the interconnect throughput
- * restriction for this device, call with r = 0.
+ * Multiple calls to omap_pm_set_min_bus_tput() will replace the
+ * previous rate value for this device.  To remove the interconnect
+ * throughput restriction for this device, call with r = 0.
  *
- * No return value.
+ * Returns -EINVAL for an invalid argument, -ERANGE if the constraint
+ * is not satisfiable, or 0 upon success.
  */
-void omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r);
+int omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r);
 
 
 /**
  * omap_pm_set_max_dev_wakeup_lat - set the maximum device enable latency
- * @dev: struct device *
+ * @req_dev: struct device * requesting the constraint, or NULL if none
+ * @dev: struct device * to set the constraint one
  * @t: maximum device wakeup latency in microseconds
  *
- * Request that the maximum amount of time necessary for a device to
- * become accessible after its clocks are enabled should be no greater
- * than 't' microseconds.  Specifically, this represents the time from
- * when a device driver enables device clocks with clk_enable(), to
- * when the register reads and writes on the device will succeed.
- * This function should be called before clk_disable() is called,
- * since the power state transition decision may be made during
- * clk_disable().
+ * Request that the maximum amount of time necessary for a device @dev
+ * to become accessible after its clocks are enabled should be no
+ * greater than @t microseconds.  Specifically, this represents the
+ * time from when a device driver enables device clocks with
+ * clk_enable(), to when the register reads and writes on the device
+ * will succeed.  This function should be called before clk_disable()
+ * is called, since the power state transition decision may be made
+ * during clk_disable().
  *
  * It is intended that underlying PM code will use this information to
  * determine what power state to put the powerdomain enclosing this
  * device into.
  *
- * Multiple calls to set_max_dev_wakeup_lat() will replace the
- * previous wakeup latency values for this device.  To remove the wakeup
- * latency restriction for this device, call with t = -1.
+ * Multiple calls to omap_pm_set_max_dev_wakeup_lat() will replace the
+ * previous wakeup latency values for this device.  To remove the
+ * wakeup latency restriction for this device, call with t = -1.
  *
- * No return value.
+ * Returns -EINVAL for an invalid argument, -ERANGE if the constraint
+ * is not satisfiable, or 0 upon success.
  */
-void omap_pm_set_max_dev_wakeup_lat(struct device *dev, long t);
+int omap_pm_set_max_dev_wakeup_lat(struct device *req_dev, struct device *dev,
+				   long t);
 
 
 /**
@@ -198,10 +207,71 @@ void omap_pm_set_max_dev_wakeup_lat(struct device *dev, long t);
  * value for this device.  To remove the maximum DMA latency for this
  * device, call with t = -1.
  *
- * No return value.
+ * Returns -EINVAL for an invalid argument, -ERANGE if the constraint
+ * is not satisfiable, or 0 upon success.
  */
-void omap_pm_set_max_sdma_lat(struct device *dev, long t);
+int omap_pm_set_max_sdma_lat(struct device *dev, long t);
+
 
+/**
+ * omap_pm_set_min_clk_rate - set minimum clock rate requested by @dev
+ * @dev: struct device * requesting the constraint
+ * @clk: struct clk * to set the minimum rate constraint on
+ * @r: minimum rate in Hz
+ *
+ * Request that the minimum clock rate on the device @dev's clk @clk
+ * be no less than @r Hz.
+ *
+ * It is expected that the OMAP PM code will use this information to
+ * find an OPP or clock setting that will satisfy this clock rate
+ * constraint, along with any other applicable system constraints on
+ * the clock rate or corresponding voltage, etc.
+ *
+ * omap_pm_set_min_clk_rate() differs from the clock code's
+ * clk_set_rate() in that it considers other constraints before taking
+ * any hardware action, and may change a system OPP rather than just a
+ * clock rate.  clk_set_rate() is intended to be a low-level
+ * interface.
+ *
+ * omap_pm_set_min_clk_rate() is easily open to abuse.  A better API
+ * would be something like "omap_pm_set_min_dev_performance()";
+ * however, there is no easily-generalizable concept of performance
+ * that applies to all devices.  Only a device (and possibly the
+ * device subsystem) has both the subsystem-specific knowledge, and
+ * the hardware IP block-specific knowledge, to translate a constraint
+ * on "touchscreen sampling accuracy" or "number of pixels or polygons
+ * rendered per second" to a clock rate.  This translation can be
+ * dependent on the hardware IP block's revision, or firmware version,
+ * and the driver is the only code on the system that has this
+ * information and can know how to translate that into a clock rate.
+ *
+ * The intended use-case for this function is for userspace or other
+ * kernel code to communicate a particular performance requirement to
+ * a subsystem; then for the subsystem to communicate that requirement
+ * to something that is meaningful to the device driver; then for the
+ * device driver to convert that requirement to a clock rate, and to
+ * then call omap_pm_set_min_clk_rate().
+ *
+ * Users of this function (such as device drivers) should not simply
+ * call this function with some high clock rate to ensure "high
+ * performance."  Rather, the device driver should take a performance
+ * constraint from its subsystem, such as "render at least X polygons
+ * per second," and use some formula or table to convert that into a
+ * clock rate constraint given the hardware type and hardware
+ * revision.  Device drivers or subsystems should not assume that they
+ * know how to make a power/performance tradeoff - some device use
+ * cases may tolerate a lower-fidelity device function for lower power
+ * consumption; others may demand a higher-fidelity device function,
+ * no matter what the power consumption.
+ *
+ * Multiple calls to omap_pm_set_min_clk_rate() will replace the
+ * previous rate value for the device @dev.  To remove the minimum clock
+ * rate constraint for the device, call with r = 0.
+ *
+ * Returns -EINVAL for an invalid argument, -ERANGE if the constraint
+ * is not satisfiable, or 0 upon success.
+ */
+int omap_pm_set_min_clk_rate(struct device *dev, struct clk *c, long r);
 
 /*
  * DSP Bridge-specific constraints
diff --git a/arch/arm/plat-omap/include/plat/omap_device.h b/arch/arm/plat-omap/include/plat/omap_device.h
index 3694b622c4a..25cd9ac3b09 100644
--- a/arch/arm/plat-omap/include/plat/omap_device.h
+++ b/arch/arm/plat-omap/include/plat/omap_device.h
@@ -101,6 +101,8 @@ struct omap_device *omap_device_build_ss(const char *pdev_name, int pdev_id,
 int omap_device_register(struct omap_device *od);
 int omap_early_device_register(struct omap_device *od);
 
+void __iomem *omap_device_get_rt_va(struct omap_device *od);
+
 /* OMAP PM interface */
 int omap_device_align_pm_lat(struct platform_device *pdev,
 			     u32 new_wakeup_lat_limit);
diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h
index 0eccc09ac4a..a4e508dfaba 100644
--- a/arch/arm/plat-omap/include/plat/omap_hwmod.h
+++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h
@@ -1,7 +1,7 @@
 /*
  * omap_hwmod macros, structures
  *
- * Copyright (C) 2009 Nokia Corporation
+ * Copyright (C) 2009-2010 Nokia Corporation
  * Paul Walmsley
  *
  * Created in collaboration with (alphabetical order): Benoît Cousson,
@@ -419,7 +419,7 @@ struct omap_hwmod_class {
  * @slaves: ptr to array of OCP ifs that this hwmod can respond on
  * @dev_attr: arbitrary device attributes that can be passed to the driver
  * @_sysc_cache: internal-use hwmod flags
- * @_rt_va: cached register target start address (internal use)
+ * @_mpu_rt_va: cached register target start address (internal use)
  * @_mpu_port_index: cached MPU register target slave ID (internal use)
  * @msuspendmux_reg_id: CONTROL_MSUSPENDMUX register ID (1-6)
  * @msuspendmux_shift: CONTROL_MSUSPENDMUX register bit shift
@@ -460,7 +460,7 @@ struct omap_hwmod {
 	struct omap_hwmod_ocp_if	**slaves;  /* connect to *_TA */
 	void				*dev_attr;
 	u32				_sysc_cache;
-	void __iomem			*_rt_va;
+	void __iomem			*_mpu_rt_va;
 	struct list_head		node;
 	u16				flags;
 	u8				_mpu_port_index;
@@ -482,11 +482,14 @@ int omap_hwmod_init(struct omap_hwmod **ohs);
 int omap_hwmod_register(struct omap_hwmod *oh);
 int omap_hwmod_unregister(struct omap_hwmod *oh);
 struct omap_hwmod *omap_hwmod_lookup(const char *name);
-int omap_hwmod_for_each(int (*fn)(struct omap_hwmod *oh));
-int omap_hwmod_late_init(void);
+int omap_hwmod_for_each(int (*fn)(struct omap_hwmod *oh, void *data),
+			void *data);
+int omap_hwmod_late_init(u8 skip_setup_idle);
 
 int omap_hwmod_enable(struct omap_hwmod *oh);
+int _omap_hwmod_enable(struct omap_hwmod *oh);
 int omap_hwmod_idle(struct omap_hwmod *oh);
+int _omap_hwmod_idle(struct omap_hwmod *oh);
 int omap_hwmod_shutdown(struct omap_hwmod *oh);
 
 int omap_hwmod_enable_clocks(struct omap_hwmod *oh);
@@ -504,6 +507,7 @@ int omap_hwmod_count_resources(struct omap_hwmod *oh);
 int omap_hwmod_fill_resources(struct omap_hwmod *oh, struct resource *res);
 
 struct powerdomain *omap_hwmod_get_pwrdm(struct omap_hwmod *oh);
+void __iomem *omap_hwmod_get_mpu_rt_va(struct omap_hwmod *oh);
 
 int omap_hwmod_add_initiator_dep(struct omap_hwmod *oh,
 				 struct omap_hwmod *init_oh);
diff --git a/arch/arm/plat-omap/include/plat/smp.h b/arch/arm/plat-omap/include/plat/smp.h
index 8983d54c4fd..6a3ff65c030 100644
--- a/arch/arm/plat-omap/include/plat/smp.h
+++ b/arch/arm/plat-omap/include/plat/smp.h
@@ -30,6 +30,7 @@
 extern void omap_secondary_startup(void);
 extern u32 omap_modify_auxcoreboot0(u32 set_mask, u32 clear_mask);
 extern void omap_auxcoreboot_addr(u32 cpu_addr);
+extern u32 omap_read_auxcoreboot0(void);
 
 /*
  * We use Soft IRQ1 as the IPI
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
index bbedd71943f..ddf723be48d 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -25,6 +25,8 @@
 
 #include <plat/serial.h>
 
+#define MDR1_MODE_MASK			0x07
+
 static volatile u8 *uart_base;
 static int uart_shift;
 
@@ -42,6 +44,10 @@ static void putc(int c)
 	if (!uart_base)
 		return;
 
+	/* Check for UART 16x mode */
+	if ((uart_base[UART_OMAP_MDR1 << uart_shift] & MDR1_MODE_MASK) != 0)
+		return;
+
 	while (!(uart_base[UART_LSR << uart_shift] & UART_LSR_THRE))
 		barrier();
 	uart_base[UART_TX << uart_shift] = c;
diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
index 98eef5360e6..2a9427c8cc4 100644
--- a/arch/arm/plat-omap/include/plat/usb.h
+++ b/arch/arm/plat-omap/include/plat/usb.h
@@ -81,7 +81,34 @@ extern void usb_ohci_init(const struct ohci_hcd_omap_platform_data *pdata);
 
 #endif
 
-void omap_usb_init(struct omap_usb_config *pdata);
+
+/*
+ * FIXME correct answer depends on hmc_mode,
+ * as does (on omap1) any nonzero value for config->otg port number
+ */
+#ifdef	CONFIG_USB_GADGET_OMAP
+#define	is_usb0_device(config)	1
+#else
+#define	is_usb0_device(config)	0
+#endif
+
+void omap_otg_init(struct omap_usb_config *config);
+
+#if defined(CONFIG_USB) || defined(CONFIG_USB_MODULE)
+void omap1_usb_init(struct omap_usb_config *pdata);
+#else
+static inline void omap1_usb_init(struct omap_usb_config *pdata)
+{
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP_OTG) || defined(CONFIG_ARCH_OMAP_OTG_MODULE)
+void omap2_usbfs_init(struct omap_usb_config *pdata);
+#else
+static inline omap2_usbfs_init(struct omap_usb_config *pdata)
+{
+}
+#endif
 
 /*-------------------------------------------------------------------------*/
 
@@ -192,4 +219,24 @@ void omap_usb_init(struct omap_usb_config *pdata);
 #	define	USB0PUENACTLOI		(1 << 16)
 #	define	USBSTANDBYCTRL		(1 << 15)
 
+#if defined(CONFIG_ARCH_OMAP1) && defined(CONFIG_USB)
+u32 omap1_usb0_init(unsigned nwires, unsigned is_device);
+u32 omap1_usb1_init(unsigned nwires);
+u32 omap1_usb2_init(unsigned nwires, unsigned alt_pingroup);
+#else
+static inline u32 omap1_usb0_init(unsigned nwires, unsigned is_device)
+{
+	return 0;
+}
+static inline u32 omap1_usb1_init(unsigned nwires)
+{
+	return 0;
+
+}
+static inline u32 omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
+{
+	return 0;
+}
+#endif
+
 #endif	/* __ASM_ARCH_OMAP_USB_H */