[ARM] pxa: simplify ifdef in ssp.h

Try to keep minimum ifdef in ssp.h.  Some of the definitions are valid
only to specific SoCs, and device drivers should be responsible to take
care of these difference.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

1 files changed, 15 insertions, 26 deletions

diff --git a/arch/arm/plat-pxa/include/plat/ssp.h b/arch/arm/plat-pxa/include/plat/ssp.h
index 4c4ce62390d..74f70c7cc4f 100644
--- a/arch/arm/plat-pxa/include/plat/ssp.h
+++ b/arch/arm/plat-pxa/include/plat/ssp.h
@@ -40,10 +40,7 @@
 #define SSRSA		(0x34)  /* SSP Rx Timeslot Active */
 #define SSTSS		(0x38)  /* SSP Timeslot Status */
 #define SSACD		(0x3C)  /* SSP Audio Clock Divider */
-
-#if defined(CONFIG_PXA3xx)
 #define SSACDD		(0x40)	/* SSP Audio Clock Dither Divider */
-#endif
 
 /* Common PXA2xx bits first */
 #define SSCR0_DSS	(0x0000000f)	/* Data Size Select (mask) */
@@ -56,20 +53,17 @@
 #define SSCR0_SSE	(1 << 7)	/* Synchronous Serial Port Enable */
 #define SSCR0_SCR(x)	((x) << 8)	/* Serial Clock Rate (mask) */
 
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
+/* PXA27x, PXA3xx */
 #define SSCR0_EDSS	(1 << 20)	/* Extended data size select */
 #define SSCR0_NCS	(1 << 21)	/* Network clock select */
 #define SSCR0_RIM	(1 << 22)	/* Receive FIFO overrrun interrupt mask */
 #define SSCR0_TUM	(1 << 23)	/* Transmit FIFO underrun interrupt mask */
 #define SSCR0_FRDC	(0x07000000)	/* Frame rate divider control (mask) */
 #define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24)	/* Time slots per frame [1..8] */
+#define SSCR0_FPCKE	(1 << 29)	/* FIFO packing enable */
 #define SSCR0_ACS	(1 << 30)	/* Audio clock select */
 #define SSCR0_MOD	(1 << 31)	/* Mode (normal or network) */
-#endif
 
-#if defined(CONFIG_PXA3xx)
-#define SSCR0_FPCKE	(1 << 29)	/* FIFO packing enable */
-#endif
 
 #define SSCR1_RIE	(1 << 0)	/* Receive FIFO Interrupt Enable */
 #define SSCR1_TIE	(1 << 1)	/* Transmit FIFO Interrupt Enable */
@@ -89,10 +83,6 @@
 #define SSSR_RFS	(1 << 6)	/* Receive FIFO Service Request */
 #define SSSR_ROR	(1 << 7)	/* Receive FIFO Overrun */
 
-#define SSCR0_TIM		(1 << 23)	/* Transmit FIFO Under Run Interrupt Mask */
-#define SSCR0_RIM		(1 << 22)	/* Receive FIFO Over Run interrupt Mask */
-#define SSCR0_NCS		(1 << 21)	/* Network Clock Select */
-#define SSCR0_EDSS		(1 << 20)	/* Extended Data Size Select */
 
 /* extra bits in PXA255, PXA26x and PXA27x SSP ports */
 #define SSCR0_TISSP		(1 << 4)	/* TI Sync Serial Protocol */
@@ -122,27 +112,26 @@
 #define SSSR_TINT		(1 << 19)	/* Receiver Time-out Interrupt */
 #define SSSR_PINT		(1 << 18)	/* Peripheral Trailing Byte Interrupt */
 
-#if defined(CONFIG_PXA3xx)
-#define SSPSP_EDMYSTOP(x)	((x) << 28)     /* Extended Dummy Stop */
-#define SSPSP_EDMYSTRT(x)	((x) << 26)     /* Extended Dummy Start */
-#endif
 
-#define SSPSP_FSRT		(1 << 25)	/* Frame Sync Relative Timing */
-#define SSPSP_DMYSTOP(x)	((x) << 23)	/* Dummy Stop */
-#define SSPSP_SFRMWDTH(x)	((x) << 16)	/* Serial Frame Width */
-#define SSPSP_SFRMDLY(x)	((x) << 9)	/* Serial Frame Delay */
-#define SSPSP_DMYSTRT(x)	((x) << 7)	/* Dummy Start */
-#define SSPSP_STRTDLY(x)	((x) << 4)	/* Start Delay */
-#define SSPSP_ETDS		(1 << 3)	/* End of Transfer data State */
-#define SSPSP_SFRMP		(1 << 2)	/* Serial Frame Polarity */
 #define SSPSP_SCMODE(x)		((x) << 0)	/* Serial Bit Rate Clock Mode */
+#define SSPSP_SFRMP		(1 << 2)	/* Serial Frame Polarity */
+#define SSPSP_ETDS		(1 << 3)	/* End of Transfer data State */
+#define SSPSP_STRTDLY(x)	((x) << 4)	/* Start Delay */
+#define SSPSP_DMYSTRT(x)	((x) << 7)	/* Dummy Start */
+#define SSPSP_SFRMDLY(x)	((x) << 9)	/* Serial Frame Delay */
+#define SSPSP_SFRMWDTH(x)	((x) << 16)	/* Serial Frame Width */
+#define SSPSP_DMYSTOP(x)	((x) << 23)	/* Dummy Stop */
+#define SSPSP_FSRT		(1 << 25)	/* Frame Sync Relative Timing */
+
+/* PXA3xx */
+#define SSPSP_EDMYSTRT(x)	((x) << 26)     /* Extended Dummy Start */
+#define SSPSP_EDMYSTOP(x)	((x) << 28)     /* Extended Dummy Stop */
+#define SSPSP_TIMING_MASK	(0x7f8001f0)
 
 #define SSACD_SCDB		(1 << 3)	/* SSPSYSCLK Divider Bypass */
 #define SSACD_ACPS(x)		((x) << 4)	/* Audio clock PLL select */
 #define SSACD_ACDS(x)		((x) << 0)	/* Audio clock divider select */
-#if defined(CONFIG_PXA3xx)
 #define SSACD_SCDX8		(1 << 7)	/* SYSCLK division ratio select */
-#endif
 
 enum pxa_ssp_type {
 	SSP_UNDEFINED = 0,