ARM: SAMSUNG: Move plat-s3c Kconfig entries to plat-samsung and plat-s3c24xx

Move the Kconfig entries from plat-s3c to plat-samsung and plat-s3c24xx
as necessary. The S3C_BOOT entries and the DMA configuration can go to
plat-samsung. The low-level UART configurations are currently S3C2XX
specific and can go to plat-s3c24xx.

Eliminating plat-s3c from the build process will be submitted seperately.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>

1 files changed, 0 insertions, 85 deletions

diff --git a/arch/arm/plat-s3c/Kconfig b/arch/arm/plat-s3c/Kconfig
index 2367908c4f6..6108ba9c2be 100644
--- a/arch/arm/plat-s3c/Kconfig
+++ b/arch/arm/plat-s3c/Kconfig
@@ -9,88 +9,3 @@ config PLAT_S3C
 	select NO_IOPORT
 	help
 	  Base platform code for any Samsung S3C device
-
-# low-level serial option nodes
-
-if PLAT_S3C
-
-config CPU_LLSERIAL_S3C2410_ONLY
-	bool
-	default y if CPU_LLSERIAL_S3C2410 && !CPU_LLSERIAL_S3C2440
-
-config CPU_LLSERIAL_S3C2440_ONLY
-	bool
-	default y if CPU_LLSERIAL_S3C2440 && !CPU_LLSERIAL_S3C2410
-
-config CPU_LLSERIAL_S3C2410
-	bool
-	help
-	  Selected if there is an S3C2410 (or register compatible) serial
-	  low-level implementation needed
-
-config CPU_LLSERIAL_S3C2440
-	bool
-	help
-	  Selected if there is an S3C2440 (or register compatible) serial
-	  low-level implementation needed
-
-# boot configurations
-
-comment "Boot options"
-
-config S3C_BOOT_WATCHDOG
-	bool "S3C Initialisation watchdog"
-	depends on S3C2410_WATCHDOG
-	help
-	  Say y to enable the watchdog during the kernel decompression
-	  stage. If the kernel fails to uncompress, then the watchdog
-	  will trigger a reset and the system should restart.
-
-config S3C_BOOT_ERROR_RESET
-	bool "S3C Reboot on decompression error"
-	help
-	  Say y here to use the watchdog to reset the system if the
-	  kernel decompressor detects an error during decompression.
-
-config S3C_BOOT_UART_FORCE_FIFO
-       bool "Force UART FIFO on during boot process"
-       default y
-       help
-         Say Y here to force the UART FIFOs on during the kernel
-	 uncompressor
-
-
-config S3C_LOWLEVEL_UART_PORT
-	int "S3C UART to use for low-level messages"
-	default 0
-	help
-	  Choice of which UART port to use for the low-level messages,
-	  such as the `Uncompressing...` at start time. The value of
-	  this configuration should be between zero and two. The port
-	  must have been initialised by the boot-loader before use.
-
-# options for gpiolib support
-
-config S3C_GPIO_SPACE
-	int "Space between gpio banks"
-	default 0
-	help
-	  Add a number of spare GPIO entries between each bank for debugging
-	  purposes. This allows any problems where an counter overflows from
-	  one bank to another to be caught, at the expense of using a little
-	  more memory.
-
-config S3C_GPIO_TRACK
-	bool
-	help
-	  Internal configuration option to enable the s3c specific gpio
-	  chip tracking if the platform requires it.
-
-# DMA
-
-config S3C_DMA
-	bool
-	help
-	  Internal configuration for S3C DMA core
-
-endif