ARM: SAMSUNG: Move plat-s3c Kconfig entries to plat-samsung and plat-s3c24xx

Move the Kconfig entries from plat-s3c to plat-samsung and plat-s3c24xx
as necessary. The S3C_BOOT entries and the DMA configuration can go to
plat-samsung. The low-level UART configurations are currently S3C2XX
specific and can go to plat-s3c24xx.

Eliminating plat-s3c from the build process will be submitted seperately.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>

1 files changed, 59 insertions, 0 deletions

diff --git a/arch/arm/plat-samsung/Kconfig b/arch/arm/plat-samsung/Kconfig
index 72da6461db1..93bd89385f5 100644
--- a/arch/arm/plat-samsung/Kconfig
+++ b/arch/arm/plat-samsung/Kconfig
@@ -13,6 +13,43 @@ config PLAT_SAMSUNG
 
 if PLAT_SAMSUNG
 
+# boot configurations
+
+comment "Boot options"
+
+config S3C_BOOT_WATCHDOG
+	bool "S3C Initialisation watchdog"
+	depends on S3C2410_WATCHDOG
+	help
+	  Say y to enable the watchdog during the kernel decompression
+	  stage. If the kernel fails to uncompress, then the watchdog
+	  will trigger a reset and the system should restart.
+
+config S3C_BOOT_ERROR_RESET
+	bool "S3C Reboot on decompression error"
+	help
+	  Say y here to use the watchdog to reset the system if the
+	  kernel decompressor detects an error during decompression.
+
+config S3C_BOOT_UART_FORCE_FIFO
+       bool "Force UART FIFO on during boot process"
+       default y
+       help
+         Say Y here to force the UART FIFOs on during the kernel
+	 uncompressor
+
+
+config S3C_LOWLEVEL_UART_PORT
+	int "S3C UART to use for low-level messages"
+	default 0
+	help
+	  Choice of which UART port to use for the low-level messages,
+	  such as the `Uncompressing...` at start time. The value of
+	  this configuration should be between zero and two. The port
+	  must have been initialised by the boot-loader before use.
+
+# clock options
+
 config SAMSUNG_CLKSRC
 	bool
 	help
@@ -81,6 +118,21 @@ config SAMSUNG_GPIO_EXTRA
 	  provides. This allows expanding the GPIO space for use with
 	  GPIO expanders.
 
+config S3C_GPIO_SPACE
+	int "Space between gpio banks"
+	default 0
+	help
+	  Add a number of spare GPIO entries between each bank for debugging
+	  purposes. This allows any problems where an counter overflows from
+	  one bank to another to be caught, at the expense of using a little
+	  more memory.
+
+config S3C_GPIO_TRACK
+	bool
+	help
+	  Internal configuration option to enable the s3c specific gpio
+	  chip tracking if the platform requires it.
+
 # ADC driver
 
 config S3C_ADC
@@ -138,6 +190,13 @@ config S3C64XX_DEV_SPI
 	  Compile in platform device definitions for S3C64XX's type
 	  SPI controllers.
 
+# DMA
+
+config S3C_DMA
+	bool
+	help
+	  Internal configuration for S3C DMA core
+
 comment "Power management"
 
 config SAMSUNG_PM_DEBUG