Merge branch 'consolidate-clksrc-i8253' of master.kernel.org:~rmk/linux-2.6-arm into timers/clocksource

Conflicts:
	arch/ia64/kernel/cyclone.c
	arch/mips/kernel/i8253.c
	arch/x86/kernel/i8253.c

Reason: Resolve conflicts so further cleanups do not conflict further

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

1 files changed, 19 insertions, 3 deletions

diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg.h b/arch/arm/plat-samsung/include/plat/gpio-cfg.h
index e4b5cf126fa..1762dcb4cb9 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-cfg.h
+++ b/arch/arm/plat-samsung/include/plat/gpio-cfg.h
@@ -125,7 +125,7 @@ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
  *
  * These values control the state of the weak pull-{up,down} resistors
  * available on most pins on the S3C series. Not all chips support both
- * up or down settings, and it may be dependant on the chip that is being
+ * up or down settings, and it may be dependent on the chip that is being
  * used to whether the particular mode is available.
  */
 #define S3C_GPIO_PULL_NONE	((__force s3c_gpio_pull_t)0x00)
@@ -138,7 +138,7 @@ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
  * @pull: The configuration for the pull resistor.
  *
  * This function sets the state of the pull-{up,down} resistor for the
- * specified pin. It will return 0 if successfull, or a negative error
+ * specified pin. It will return 0 if successful, or a negative error
  * code if the pin cannot support the requested pull setting.
  *
  * @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP.
@@ -202,7 +202,7 @@ extern s5p_gpio_drvstr_t s5p_gpio_get_drvstr(unsigned int pin);
  * @drvstr: The new value of the driver strength
  *
  * This function sets the driver strength value for the specified pin.
- * It will return 0 if successfull, or a negative error code if the pin
+ * It will return 0 if successful, or a negative error code if the pin
  * cannot support the requested setting.
 */
 extern int s5p_gpio_set_drvstr(unsigned int pin, s5p_gpio_drvstr_t drvstr);
@@ -225,4 +225,20 @@ extern int s5p_gpio_set_drvstr(unsigned int pin, s5p_gpio_drvstr_t drvstr);
  */
 extern int s5p_register_gpio_interrupt(int pin);
 
+/** s5p_register_gpioint_bank() - add gpio bank for further gpio interrupt
+ * registration (see s5p_register_gpio_interrupt function)
+ * @chain_irq: chained irq number for the gpio int handler for this bank
+ * @start: start gpio group number of this bank
+ * @nr_groups: number of gpio groups handled by this bank
+ *
+ * This functions registers initial information about gpio banks that
+ * can be later used by the s5p_register_gpio_interrupt() function to
+ * enable support for gpio interrupt for particular gpio group.
+ */
+#ifdef CONFIG_S5P_GPIO_INT
+extern int s5p_register_gpioint_bank(int chain_irq, int start, int nr_groups);
+#else
+#define s5p_register_gpioint_bank(chain_irq, start, nr_groups) do { } while (0)
+#endif
+
 #endif /* __PLAT_GPIO_CFG_H */