Merge tag 'omap-for-v3.9/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards

From Tony Lindgren:
Minimal updates to OMAP board-*.c files while converting
things to device tree based booting.

* tag 'omap-for-v3.9/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
  RX-51: Register twl4030-madc device
  RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
  ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
  ARM: OMAP1: nokia770: enable CBUS/Retu
  ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
  ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
  ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
  ARM: OMAP2+: craneboard: support the TPS65910 PMU
  ARM: OMAP2+: craneboard: support NAND device
  ARM: OMAP3: cm-t3517: add MMC support
  ARM: OMAP2+: Remove apollon board support
  + Linux 3.8-rc6

Signed-off-by: Olof Johansson <olof@lixom.net>

63 files changed, 408 insertions, 589 deletions

diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
index 00044026ef1..9b82facb256 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/armada-370-db.dts
@@ -26,7 +26,7 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0x00000000 0x20000000>; /* 512 MB */
+		reg = <0x00000000 0x40000000>; /* 1 GB */
 	};
 
 	soc {
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
index 271855a6e22..e041f42ed71 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -50,27 +50,25 @@
 		};
 
 		gpio0: gpio@d0018100 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018100 0x40>,
-			    <0xd0018800 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018100 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <16>, <17>, <18>, <19>;
+			interrupts = <82>, <83>, <84>, <85>;
 		};
 
 		gpio1: gpio@d0018140 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018140 0x40>,
-			    <0xd0018840 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018140 0x40>;
 			ngpios = <17>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <20>, <21>, <22>;
+			interrupts = <87>, <88>, <89>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
index 1c1937dbce7..9e23bd8c953 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -51,39 +51,36 @@
 		};
 
 		gpio0: gpio@d0018100 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018100 0x40>,
-			    <0xd0018800 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018100 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <16>, <17>, <18>, <19>;
+			interrupts = <82>, <83>, <84>, <85>;
 		};
 
 		gpio1: gpio@d0018140 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018140 0x40>,
-			    <0xd0018840 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018140 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <20>, <21>, <22>, <23>;
+			interrupts = <87>, <88>, <89>, <90>;
 		};
 
 		gpio2: gpio@d0018180 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018180 0x40>,
-			    <0xd0018870 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018180 0x40>;
 			ngpios = <3>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <24>;
+			interrupts = <91>;
 		};
 
 		ethernet@d0034000 {
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
index 4905cf3a5ef..965966110e3 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
@@ -66,39 +66,36 @@
 		};
 
 		gpio0: gpio@d0018100 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018100 0x40>,
-			    <0xd0018800 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018100 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <16>, <17>, <18>, <19>;
+			interrupts = <82>, <83>, <84>, <85>;
 		};
 
 		gpio1: gpio@d0018140 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018140 0x40>,
-			    <0xd0018840 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018140 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <20>, <21>, <22>, <23>;
+			interrupts = <87>, <88>, <89>, <90>;
 		};
 
 		gpio2: gpio@d0018180 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018180 0x40>,
-			    <0xd0018870 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018180 0x40>;
 			ngpios = <3>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <24>;
+			interrupts = <91>;
 		};
 
 		ethernet@d0034000 {
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index e154f242c68..222047f1ece 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -336,8 +336,8 @@
 
 	i2c@0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 23 0 /* sda */
-			 &pioA 24 0 /* scl */
+		gpios = <&pioA 25 0 /* sda */
+			 &pioA 26 0 /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index 3a47cf95214..8ecca6948d8 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -143,6 +143,11 @@
 						atmel,pins =
 							<0 3 0x1 0x0>;	/* PA3 periph A */
 					};
+
+					pinctrl_usart0_sck: usart0_sck-0 {
+						atmel,pins =
+							<0 4 0x1 0x0>;	/* PA4 periph A */
+					};
 				};
 
 				usart1 {
@@ -154,12 +159,17 @@
 
 					pinctrl_usart1_rts: usart1_rts-0 {
 						atmel,pins =
-							<3 27 0x3 0x0>;	/* PC27 periph C */
+							<2 27 0x3 0x0>;	/* PC27 periph C */
 					};
 
 					pinctrl_usart1_cts: usart1_cts-0 {
 						atmel,pins =
-							<3 28 0x3 0x0>;	/* PC28 periph C */
+							<2 28 0x3 0x0>;	/* PC28 periph C */
+					};
+
+					pinctrl_usart1_sck: usart1_sck-0 {
+						atmel,pins =
+							<2 28 0x3 0x0>;	/* PC29 periph C */
 					};
 				};
 
@@ -172,46 +182,56 @@
 
 					pinctrl_uart2_rts: uart2_rts-0 {
 						atmel,pins =
-							<0 0 0x2 0x0>;	/* PB0 periph B */
+							<1 0 0x2 0x0>;	/* PB0 periph B */
 					};
 
 					pinctrl_uart2_cts: uart2_cts-0 {
 						atmel,pins =
-							<0 1 0x2 0x0>;	/* PB1 periph B */
+							<1 1 0x2 0x0>;	/* PB1 periph B */
+					};
+
+					pinctrl_usart2_sck: usart2_sck-0 {
+						atmel,pins =
+							<1 2 0x2 0x0>;	/* PB2 periph B */
 					};
 				};
 
 				usart3 {
 					pinctrl_uart3: usart3-0 {
 						atmel,pins =
-							<3 23 0x2 0x1	/* PC22 periph B with pullup */
-							 3 23 0x2 0x0>;	/* PC23 periph B */
+							<2 23 0x2 0x1	/* PC22 periph B with pullup */
+							 2 23 0x2 0x0>;	/* PC23 periph B */
 					};
 
 					pinctrl_usart3_rts: usart3_rts-0 {
 						atmel,pins =
-							<3 24 0x2 0x0>;	/* PC24 periph B */
+							<2 24 0x2 0x0>;	/* PC24 periph B */
 					};
 
 					pinctrl_usart3_cts: usart3_cts-0 {
 						atmel,pins =
-							<3 25 0x2 0x0>;	/* PC25 periph B */
+							<2 25 0x2 0x0>;	/* PC25 periph B */
+					};
+
+					pinctrl_usart3_sck: usart3_sck-0 {
+						atmel,pins =
+							<2 26 0x2 0x0>;	/* PC26 periph B */
 					};
 				};
 
 				uart0 {
 					pinctrl_uart0: uart0-0 {
 						atmel,pins =
-							<3 8 0x3 0x0	/* PC8 periph C */
-							 3 9 0x3 0x1>;	/* PC9 periph C with pullup */
+							<2 8 0x3 0x0	/* PC8 periph C */
+							 2 9 0x3 0x1>;	/* PC9 periph C with pullup */
 					};
 				};
 
 				uart1 {
 					pinctrl_uart1: uart1-0 {
 						atmel,pins =
-							<3 16 0x3 0x0	/* PC16 periph C */
-							 3 17 0x3 0x1>;	/* PC17 periph C with pullup */
+							<2 16 0x3 0x0	/* PC16 periph C */
+							 2 17 0x3 0x1>;	/* PC17 periph C with pullup */
 					};
 				};
 
@@ -240,14 +260,14 @@
 
 					pinctrl_macb0_rmii_mii: macb0_rmii_mii-0 {
 						atmel,pins =
-							<1 8 0x1 0x0	/* PA8 periph A */
-							 1 11 0x1 0x0	/* PA11 periph A */
-							 1 12 0x1 0x0	/* PA12 periph A */
-							 1 13 0x1 0x0	/* PA13 periph A */
-							 1 14 0x1 0x0	/* PA14 periph A */
-							 1 15 0x1 0x0	/* PA15 periph A */
-							 1 16 0x1 0x0	/* PA16 periph A */
-							 1 17 0x1 0x0>;	/* PA17 periph A */
+							<1 8 0x1 0x0	/* PB8 periph A */
+							 1 11 0x1 0x0	/* PB11 periph A */
+							 1 12 0x1 0x0	/* PB12 periph A */
+							 1 13 0x1 0x0	/* PB13 periph A */
+							 1 14 0x1 0x0	/* PB14 periph A */
+							 1 15 0x1 0x0	/* PB15 periph A */
+							 1 16 0x1 0x0	/* PB16 periph A */
+							 1 17 0x1 0x0>;	/* PB17 periph A */
 					};
 				};
 
diff --git a/arch/arm/boot/dts/cros5250-common.dtsi b/arch/arm/boot/dts/cros5250-common.dtsi
index fddd1741743..46c09801703 100644
--- a/arch/arm/boot/dts/cros5250-common.dtsi
+++ b/arch/arm/boot/dts/cros5250-common.dtsi
@@ -96,8 +96,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;
@@ -120,8 +120,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;
@@ -141,8 +141,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;
diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts
index fed7d3f9f43..cdee96fca6e 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/dove-cubox.dts
@@ -26,10 +26,15 @@
 };
 
 &uart0 { status = "okay"; };
-&sdio0 { status = "okay"; };
 &sata0 { status = "okay"; };
 &i2c0 { status = "okay"; };
 
+&sdio0 {
+	status = "okay";
+	/* sdio0 card detect is connected to wrong pin on CuBox */
+	cd-gpios = <&gpio0 12 1>;
+};
+
 &spi0 {
 	status = "okay";
 
@@ -42,9 +47,14 @@
 };
 
 &pinctrl {
-	pinctrl-0 = <&pmx_gpio_18>;
+	pinctrl-0 = <&pmx_gpio_12 &pmx_gpio_18>;
 	pinctrl-names = "default";
 
+	pmx_gpio_12: pmx-gpio-12 {
+		marvell,pins = "mpp12";
+		marvell,function = "gpio";
+	};
+
 	pmx_gpio_18: pmx-gpio-18 {
 		marvell,pins = "mpp18";
 		marvell,function = "gpio";
diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
index 942d5761ca9..e05b18f3c33 100644
--- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
@@ -115,8 +115,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;
@@ -139,8 +139,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;
diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
index 9bc6785ad22..77d21abfcdf 100644
--- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
@@ -1,4 +1,5 @@
 /include/ "kirkwood.dtsi"
+/include/ "kirkwood-6281.dtsi"
 
 / {
 	chosen {
@@ -6,6 +7,21 @@
 	};
 
 	ocp@f1000000 {
+		pinctrl: pinctrl@10000 {
+			pinctrl-0 = < &pmx_spi &pmx_twsi0 &pmx_uart0
+					&pmx_ns2_sata0 &pmx_ns2_sata1>;
+			pinctrl-names = "default";
+
+			pmx_ns2_sata0: pmx-ns2-sata0 {
+				marvell,pins = "mpp21";
+				marvell,function = "sata0";
+			};
+			pmx_ns2_sata1: pmx-ns2-sata1 {
+				marvell,pins = "mpp20";
+				marvell,function = "sata1";
+			};
+		};
+
 		serial@12000 {
 			clock-frequency = <166666667>;
 			status = "okay";
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 110d6cbb795..d6ab442b701 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -36,6 +36,7 @@
 			reg = <0x10100 0x40>;
 			ngpios = <32>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <35>, <36>, <37>, <38>;
 		};
 
@@ -46,6 +47,7 @@
 			reg = <0x10140 0x40>;
 			ngpios = <18>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <39>, <40>, <41>;
 		};
 
diff --git a/arch/arm/boot/dts/kizbox.dts b/arch/arm/boot/dts/kizbox.dts
index e8814fe0e27..b4dc3ed9a3e 100644
--- a/arch/arm/boot/dts/kizbox.dts
+++ b/arch/arm/boot/dts/kizbox.dts
@@ -48,6 +48,8 @@
 
 			macb0: ethernet@fffc4000 {
 				phy-mode = "mii";
+				pinctrl-0 = <&pinctrl_macb_rmii
+				             &pinctrl_macb_rmii_mii_alt>;
 				status = "okay";
 			};
 
diff --git a/arch/arm/boot/dts/sunxi.dtsi b/arch/arm/boot/dts/sunxi.dtsi
index 8bbc2bfef22..8b36abea9f2 100644
--- a/arch/arm/boot/dts/sunxi.dtsi
+++ b/arch/arm/boot/dts/sunxi.dtsi
@@ -60,19 +60,21 @@
 		};
 
 		uart0: uart@01c28000 {
-			compatible = "ns8250";
+			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
 			interrupts = <1>;
 			reg-shift = <2>;
+			reg-io-width = <4>;
 			clock-frequency = <24000000>;
 			status = "disabled";
 		};
 
 		uart1: uart@01c28400 {
-			compatible = "ns8250";
+			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28400 0x400>;
 			interrupts = <2>;
 			reg-shift = <2>;
+			reg-io-width = <4>;
 			clock-frequency = <24000000>;
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
index 1fc405a9ecf..cf8071ad22d 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
+++ b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
@@ -45,7 +45,6 @@
 			reg = <1>;
 		};
 
-/* A7s disabled till big.LITTLE patches are available...
 		cpu2: cpu@2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
@@ -63,7 +62,6 @@
 			compatible = "arm,cortex-a7";
 			reg = <0x102>;
 		};
-*/
 	};
 
 	memory@80000000 {
diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig
index b175577d7ab..1ea959019fc 100644
--- a/arch/arm/configs/at91_dt_defconfig
+++ b/arch/arm/configs/at91_dt_defconfig
@@ -19,6 +19,7 @@ CONFIG_SOC_AT91SAM9260=y
 CONFIG_SOC_AT91SAM9263=y
 CONFIG_SOC_AT91SAM9G45=y
 CONFIG_SOC_AT91SAM9X5=y
+CONFIG_SOC_AT91SAM9N12=y
 CONFIG_MACH_AT91SAM_DT=y
 CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
 CONFIG_AT91_TIMER_HZ=128
@@ -31,7 +32,7 @@ CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
-CONFIG_CMDLINE="mem=128M console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
 CONFIG_KEXEC=y
 CONFIG_AUTO_ZRELADDR=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index 82ce8d738fa..76938cb50b4 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -52,6 +52,11 @@ CONFIG_IP_PNP_RARP=y
 # CONFIG_INET_LRO is not set
 # CONFIG_IPV6 is not set
 CONFIG_NETFILTER=y
+CONFIG_CAN=m
+CONFIG_CAN_RAW=m
+CONFIG_CAN_BCM=m
+CONFIG_CAN_C_CAN=m
+CONFIG_CAN_C_CAN_PLATFORM=m
 CONFIG_BT=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_H4=y
@@ -64,6 +69,7 @@ CONFIG_MAC80211=m
 CONFIG_MAC80211_RC_PID=y
 CONFIG_MAC80211_RC_DEFAULT_PID=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_CMA=y
 CONFIG_CONNECTOR=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
@@ -83,6 +89,9 @@ CONFIG_MTD_UBI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_SENSORS_LIS3LV02D=m
+CONFIG_SENSORS_TSL2550=m
+CONFIG_SENSORS_LIS3_I2C=m
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_SCSI_MULTI_LUN=y
@@ -108,6 +117,7 @@ CONFIG_USB_KC2190=y
 CONFIG_INPUT_JOYDEV=y
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_MATRIX=m
 CONFIG_KEYBOARD_TWL4030=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=y
@@ -131,14 +141,17 @@ CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_TWL4030=y
 CONFIG_W1=y
 CONFIG_POWER_SUPPLY=y
+CONFIG_SENSORS_LM75=m
 CONFIG_WATCHDOG=y
 CONFIG_OMAP_WATCHDOG=y
 CONFIG_TWL4030_WATCHDOG=y
 CONFIG_MFD_TPS65217=y
+CONFIG_MFD_TPS65910=y
 CONFIG_REGULATOR_TWL4030=y
 CONFIG_REGULATOR_TPS65023=y
 CONFIG_REGULATOR_TPS6507X=y
 CONFIG_REGULATOR_TPS65217=y
+CONFIG_REGULATOR_TPS65910=y
 CONFIG_FB=y
 CONFIG_FIRMWARE_EDID=y
 CONFIG_FB_MODE_HELPERS=y
@@ -150,6 +163,7 @@ CONFIG_OMAP2_DSS_SDI=y
 CONFIG_OMAP2_DSS_DSI=y
 CONFIG_FB_OMAP2=m
 CONFIG_PANEL_GENERIC_DPI=m
+CONFIG_PANEL_TFP410=m
 CONFIG_PANEL_SHARP_LS037V7DW01=m
 CONFIG_PANEL_NEC_NL8048HL11_01B=m
 CONFIG_PANEL_TAAL=m
@@ -196,9 +210,20 @@ CONFIG_MMC_UNSAFE_RESUME=y
 CONFIG_SDIO_UART=y
 CONFIG_MMC_OMAP=y
 CONFIG_MMC_OMAP_HS=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_CPU=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_TWL92330=y
 CONFIG_RTC_DRV_TWL4030=y
+CONFIG_RTC_DRV_OMAP=y
 CONFIG_DMADEVICES=y
 CONFIG_DMA_OMAP=y
 CONFIG_EXT2_FS=y
diff --git a/arch/arm/kernel/debug.S b/arch/arm/kernel/debug.S
index 6809200c31f..14f7c3b1463 100644
--- a/arch/arm/kernel/debug.S
+++ b/arch/arm/kernel/debug.S
@@ -100,12 +100,14 @@ ENTRY(printch)
 		b	1b
 ENDPROC(printch)
 
+#ifdef CONFIG_MMU
 ENTRY(debug_ll_addr)
 		addruart r2, r3, ip
 		str	r2, [r0]
 		str	r3, [r1]
 		mov	pc, lr
 ENDPROC(debug_ll_addr)
+#endif
 
 #else
 
diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S
index 4eee351f466..486a15ae901 100644
--- a/arch/arm/kernel/head.S
+++ b/arch/arm/kernel/head.S
@@ -246,6 +246,7 @@ __create_page_tables:
 
 	/*
 	 * Then map boot params address in r2 if specified.
+	 * We map 2 sections in case the ATAGs/DTB crosses a section boundary.
 	 */
 	mov	r0, r2, lsr #SECTION_SHIFT
 	movs	r0, r0, lsl #SECTION_SHIFT
@@ -253,6 +254,8 @@ __create_page_tables:
 	addne	r3, r3, #PAGE_OFFSET
 	addne	r3, r4, r3, lsr #(SECTION_SHIFT - PMD_ORDER)
 	orrne	r6, r7, r0
+	strne	r6, [r3], #1 << PMD_ORDER
+	addne	r6, r6, #1 << SECTION_SHIFT
 	strne	r6, [r3]
 
 #ifdef CONFIG_DEBUG_LL
@@ -331,7 +334,7 @@ ENTRY(secondary_startup)
 	 * as it has already been validated by the primary processor.
 	 */
 #ifdef CONFIG_ARM_VIRT_EXT
-	bl	__hyp_stub_install
+	bl	__hyp_stub_install_secondary
 #endif
 	safe_svcmode_maskall r9
 
diff --git a/arch/arm/kernel/hyp-stub.S b/arch/arm/kernel/hyp-stub.S
index 65b2417aebc..1315c4ccfa5 100644
--- a/arch/arm/kernel/hyp-stub.S
+++ b/arch/arm/kernel/hyp-stub.S
@@ -99,7 +99,7 @@ ENTRY(__hyp_stub_install_secondary)
 	 * immediately.
 	 */
 	compare_cpu_mode_with_primary	r4, r5, r6, r7
-	bxne	lr
+	movne	pc, lr
 
 	/*
 	 * Once we have given up on one CPU, we do not try to install the
@@ -111,7 +111,7 @@ ENTRY(__hyp_stub_install_secondary)
 	 */
 
 	cmp	r4, #HYP_MODE
-	bxne	lr			@ give up if the CPU is not in HYP mode
+	movne	pc, lr			@ give up if the CPU is not in HYP mode
 
 /*
  * Configure HSCTLR to set correct exception endianness/instruction set
@@ -120,7 +120,8 @@ ENTRY(__hyp_stub_install_secondary)
  * Eventually, CPU-specific code might be needed -- assume not for now
  *
  * This code relies on the "eret" instruction to synchronize the
- * various coprocessor accesses.
+ * various coprocessor accesses. This is done when we switch to SVC
+ * (see safe_svcmode_maskall).
  */
 	@ Now install the hypervisor stub:
 	adr	r7, __hyp_stub_vectors
@@ -155,14 +156,7 @@ THUMB(	orr	r7, #(1 << 30)	)	@ HSCTLR.TE
 1:
 #endif
 
-	bic	r7, r4, #MODE_MASK
-	orr	r7, r7, #SVC_MODE
-THUMB(	orr	r7, r7, #PSR_T_BIT	)
-	msr	spsr_cxsf, r7		@ This is SPSR_hyp.
-
-	__MSR_ELR_HYP(14)		@ msr elr_hyp, lr
-	__ERET				@ return, switching to SVC mode
-					@ The boot CPU mode is left in r4.
+	bx	lr			@ The boot CPU mode is left in r4.
 ENDPROC(__hyp_stub_install_secondary)
 
 __hyp_stub_do_trap:
@@ -200,7 +194,7 @@ ENDPROC(__hyp_get_vectors)
 	@ fall through
 ENTRY(__hyp_set_vectors)
 	__HVC(0)
-	bx	lr
+	mov	pc, lr
 ENDPROC(__hyp_set_vectors)
 
 #ifndef ZIMAGE
diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c
index 9ee866ce047..4b678478cf9 100644
--- a/arch/arm/mach-at91/setup.c
+++ b/arch/arm/mach-at91/setup.c
@@ -105,6 +105,8 @@ static void __init soc_detect(u32 dbgu_base)
 	switch (socid) {
 	case ARCH_ID_AT91RM9200:
 		at91_soc_initdata.type = AT91_SOC_RM9200;
+		if (at91_soc_initdata.subtype == AT91_SOC_SUBTYPE_NONE)
+			at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA;
 		at91_boot_soc = at91rm9200_soc;
 		break;
 
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 3e628fd7a67..0a2349dc701 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -851,6 +851,7 @@ config SOC_IMX6Q
 	select HAVE_CAN_FLEXCAN if CAN
 	select HAVE_IMX_GPC
 	select HAVE_IMX_MMDC
+	select HAVE_IMX_SRC
 	select HAVE_SMP
 	select MFD_SYSCON
 	select PINCTRL
diff --git a/arch/arm/mach-imx/clk-imx25.c b/arch/arm/mach-imx/clk-imx25.c
index b197aa73dc4..2c570cdaae7 100644
--- a/arch/arm/mach-imx/clk-imx25.c
+++ b/arch/arm/mach-imx/clk-imx25.c
@@ -254,9 +254,9 @@ int __init mx25_clocks_init(void)
 	clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
 	clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.2");
 	clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2");
-	clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc");
-	clk_register_clkdev(clk[usbotg_ahb], "ahb", "fsl-usb2-udc");
-	clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc");
+	clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
+	clk_register_clkdev(clk[usbotg_ahb], "ahb", "imx-udc-mx27");
+	clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27");
 	clk_register_clkdev(clk[nfc_ipg_per], NULL, "imx25-nand.0");
 	/* i.mx25 has the i.mx35 type cspi */
 	clk_register_clkdev(clk[cspi1_ipg], NULL, "imx35-cspi.0");
diff --git a/arch/arm/mach-imx/clk-imx27.c b/arch/arm/mach-imx/clk-imx27.c
index 4c1d1e4efc7..1ffe3b534e5 100644
--- a/arch/arm/mach-imx/clk-imx27.c
+++ b/arch/arm/mach-imx/clk-imx27.c
@@ -236,9 +236,9 @@ int __init mx27_clocks_init(unsigned long fref)
 	clk_register_clkdev(clk[lcdc_ahb_gate], "ahb", "imx21-fb.0");
 	clk_register_clkdev(clk[csi_ahb_gate], "ahb", "imx27-camera.0");
 	clk_register_clkdev(clk[per4_gate], "per", "imx27-camera.0");
-	clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc");
-	clk_register_clkdev(clk[usb_ipg_gate], "ipg", "fsl-usb2-udc");
-	clk_register_clkdev(clk[usb_ahb_gate], "ahb", "fsl-usb2-udc");
+	clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27");
+	clk_register_clkdev(clk[usb_ipg_gate], "ipg", "imx-udc-mx27");
+	clk_register_clkdev(clk[usb_ahb_gate], "ahb", "imx-udc-mx27");
 	clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.0");
 	clk_register_clkdev(clk[usb_ipg_gate], "ipg", "mxc-ehci.0");
 	clk_register_clkdev(clk[usb_ahb_gate], "ahb", "mxc-ehci.0");
diff --git a/arch/arm/mach-imx/clk-imx31.c b/arch/arm/mach-imx/clk-imx31.c
index 8be64e0a4ac..16ccbd41dea 100644
--- a/arch/arm/mach-imx/clk-imx31.c
+++ b/arch/arm/mach-imx/clk-imx31.c
@@ -139,9 +139,9 @@ int __init mx31_clocks_init(unsigned long fref)
 	clk_register_clkdev(clk[usb_div_post], "per", "mxc-ehci.2");
 	clk_register_clkdev(clk[usb_gate], "ahb", "mxc-ehci.2");
 	clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
-	clk_register_clkdev(clk[usb_div_post], "per", "fsl-usb2-udc");
-	clk_register_clkdev(clk[usb_gate], "ahb", "fsl-usb2-udc");
-	clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc");
+	clk_register_clkdev(clk[usb_div_post], "per", "imx-udc-mx27");
+	clk_register_clkdev(clk[usb_gate], "ahb", "imx-udc-mx27");
+	clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
 	clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0");
 	/* i.mx31 has the i.mx21 type uart */
 	clk_register_clkdev(clk[uart1_gate], "per", "imx21-uart.0");
diff --git a/arch/arm/mach-imx/clk-imx35.c b/arch/arm/mach-imx/clk-imx35.c
index 66f3d65ea27..f0727e80815 100644
--- a/arch/arm/mach-imx/clk-imx35.c
+++ b/arch/arm/mach-imx/clk-imx35.c
@@ -251,9 +251,9 @@ int __init mx35_clocks_init()
 	clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2");
 	clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
 	clk_register_clkdev(clk[usbotg_gate], "ahb", "mxc-ehci.2");
-	clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc");
-	clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc");
-	clk_register_clkdev(clk[usbotg_gate], "ahb", "fsl-usb2-udc");
+	clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27");
+	clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
+	clk_register_clkdev(clk[usbotg_gate], "ahb", "imx-udc-mx27");
 	clk_register_clkdev(clk[wdog_gate], NULL, "imx2-wdt.0");
 	clk_register_clkdev(clk[nfc_div], NULL, "imx25-nand.0");
 	clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0");
diff --git a/arch/arm/mach-imx/clk-imx51-imx53.c b/arch/arm/mach-imx/clk-imx51-imx53.c
index 579023f59dc..fb7cb841b64 100644
--- a/arch/arm/mach-imx/clk-imx51-imx53.c
+++ b/arch/arm/mach-imx/clk-imx51-imx53.c
@@ -269,9 +269,9 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil,
 	clk_register_clkdev(clk[usboh3_per_gate], "per", "mxc-ehci.2");
 	clk_register_clkdev(clk[usboh3_gate], "ipg", "mxc-ehci.2");
 	clk_register_clkdev(clk[usboh3_gate], "ahb", "mxc-ehci.2");
-	clk_register_clkdev(clk[usboh3_per_gate], "per", "fsl-usb2-udc");
-	clk_register_clkdev(clk[usboh3_gate], "ipg", "fsl-usb2-udc");
-	clk_register_clkdev(clk[usboh3_gate], "ahb", "fsl-usb2-udc");
+	clk_register_clkdev(clk[usboh3_per_gate], "per", "imx-udc-mx51");
+	clk_register_clkdev(clk[usboh3_gate], "ipg", "imx-udc-mx51");
+	clk_register_clkdev(clk[usboh3_gate], "ahb", "imx-udc-mx51");
 	clk_register_clkdev(clk[nfc_gate], NULL, "imx51-nand");
 	clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "imx-ssi.0");
 	clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "imx-ssi.1");
diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c
index 7f2c10c7413..c0c4e723b7f 100644
--- a/arch/arm/mach-imx/clk-imx6q.c
+++ b/arch/arm/mach-imx/clk-imx6q.c
@@ -436,6 +436,9 @@ int __init mx6q_clocks_init(void)
 	for (i = 0; i < ARRAY_SIZE(clks_init_on); i++)
 		clk_prepare_enable(clk[clks_init_on[i]]);
 
+	/* Set initial power mode */
+	imx6q_set_lpm(WAIT_CLOCKED);
+
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt");
 	base = of_iomap(np, 0);
 	WARN_ON(!base);
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index 7191ab4434e..fa36fb84ab1 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -142,6 +142,7 @@ extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
 extern void imx6q_clock_map_io(void);
 
 extern void imx_cpu_die(unsigned int cpu);
+extern int imx_cpu_kill(unsigned int cpu);
 
 #ifdef CONFIG_PM
 extern void imx6q_pm_init(void);
diff --git a/arch/arm/mach-imx/devices/devices-common.h b/arch/arm/mach-imx/devices/devices-common.h
index 6277baf1b7b..9bd5777ff0e 100644
--- a/arch/arm/mach-imx/devices/devices-common.h
+++ b/arch/arm/mach-imx/devices/devices-common.h
@@ -63,6 +63,7 @@ struct platform_device *__init imx_add_flexcan(
 
 #include <linux/fsl_devices.h>
 struct imx_fsl_usb2_udc_data {
+	const char *devid;
 	resource_size_t iobase;
 	resource_size_t irq;
 };
diff --git a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
index 37e44398197..3c06bd96e9c 100644
--- a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
+++ b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
@@ -11,35 +11,36 @@
 #include "../hardware.h"
 #include "devices-common.h"
 
-#define imx_fsl_usb2_udc_data_entry_single(soc)				\
+#define imx_fsl_usb2_udc_data_entry_single(soc, _devid)			\
 	{								\
+		.devid = _devid,					\
 		.iobase = soc ## _USB_OTG_BASE_ADDR,			\
 		.irq = soc ## _INT_USB_OTG,				\
 	}
 
 #ifdef CONFIG_SOC_IMX25
 const struct imx_fsl_usb2_udc_data imx25_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX25);
+	imx_fsl_usb2_udc_data_entry_single(MX25, "imx-udc-mx27");
 #endif /* ifdef CONFIG_SOC_IMX25 */
 
 #ifdef CONFIG_SOC_IMX27
 const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX27);
+	imx_fsl_usb2_udc_data_entry_single(MX27, "imx-udc-mx27");
 #endif /* ifdef CONFIG_SOC_IMX27 */
 
 #ifdef CONFIG_SOC_IMX31
 const struct imx_fsl_usb2_udc_data imx31_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX31);
+	imx_fsl_usb2_udc_data_entry_single(MX31, "imx-udc-mx27");
 #endif /* ifdef CONFIG_SOC_IMX31 */
 
 #ifdef CONFIG_SOC_IMX35
 const struct imx_fsl_usb2_udc_data imx35_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX35);
+	imx_fsl_usb2_udc_data_entry_single(MX35, "imx-udc-mx27");
 #endif /* ifdef CONFIG_SOC_IMX35 */
 
 #ifdef CONFIG_SOC_IMX51
 const struct imx_fsl_usb2_udc_data imx51_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX51);
+	imx_fsl_usb2_udc_data_entry_single(MX51, "imx-udc-mx51");
 #endif
 
 struct platform_device *__init imx_add_fsl_usb2_udc(
@@ -57,7 +58,7 @@ struct platform_device *__init imx_add_fsl_usb2_udc(
 			.flags = IORESOURCE_IRQ,
 		},
 	};
-	return imx_add_platform_device_dmamask("fsl-usb2-udc", -1,
+	return imx_add_platform_device_dmamask(data->devid, -1,
 			res, ARRAY_SIZE(res),
 			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
 }
diff --git a/arch/arm/mach-imx/devices/platform-imx-fb.c b/arch/arm/mach-imx/devices/platform-imx-fb.c
index 10b0ed39f07..25a47c616b2 100644
--- a/arch/arm/mach-imx/devices/platform-imx-fb.c
+++ b/arch/arm/mach-imx/devices/platform-imx-fb.c
@@ -54,7 +54,7 @@ struct platform_device *__init imx_add_imx_fb(
 			.flags = IORESOURCE_IRQ,
 		},
 	};
-	return imx_add_platform_device_dmamask("imx-fb", 0,
+	return imx_add_platform_device_dmamask(data->devid, 0,
 			res, ARRAY_SIZE(res),
 			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
 }
diff --git a/arch/arm/mach-imx/hotplug.c b/arch/arm/mach-imx/hotplug.c
index 3dec962b077..7bc5fe15dda 100644
--- a/arch/arm/mach-imx/hotplug.c
+++ b/arch/arm/mach-imx/hotplug.c
@@ -46,9 +46,11 @@ static inline void cpu_enter_lowpower(void)
 void imx_cpu_die(unsigned int cpu)
 {
 	cpu_enter_lowpower();
-	imx_enable_cpu(cpu, false);
+	cpu_do_idle();
+}
 
-	/* spin here until hardware takes it down */
-	while (1)
-		;
+int imx_cpu_kill(unsigned int cpu)
+{
+	imx_enable_cpu(cpu, false);
+	return 1;
 }
diff --git a/arch/arm/mach-imx/iram.h b/arch/arm/mach-imx/iram.h
deleted file mode 100644
index 022690c3370..00000000000
--- a/arch/arm/mach-imx/iram.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-#include <linux/errno.h>
-
-#ifdef CONFIG_IRAM_ALLOC
-
-int __init iram_init(unsigned long base, unsigned long size);
-void __iomem *iram_alloc(unsigned int size, unsigned long *dma_addr);
-void iram_free(unsigned long dma_addr, unsigned int size);
-
-#else
-
-static inline int __init iram_init(unsigned long base, unsigned long size)
-{
-	return -ENOMEM;
-}
-
-static inline void __iomem *iram_alloc(unsigned int size, unsigned long *dma_addr)
-{
-	return NULL;
-}
-
-static inline void iram_free(unsigned long base, unsigned long size) {}
-
-#endif
diff --git a/arch/arm/mach-imx/iram_alloc.c b/arch/arm/mach-imx/iram_alloc.c
index 6c80424f678..e05cf407db6 100644
--- a/arch/arm/mach-imx/iram_alloc.c
+++ b/arch/arm/mach-imx/iram_alloc.c
@@ -22,8 +22,7 @@
 #include <linux/module.h>
 #include <linux/spinlock.h>
 #include <linux/genalloc.h>
-
-#include "iram.h"
+#include "linux/platform_data/imx-iram.h"
 
 static unsigned long iram_phys_base;
 static void __iomem *iram_virt_base;
diff --git a/arch/arm/mach-imx/platsmp.c b/arch/arm/mach-imx/platsmp.c
index 3777b805b76..66fae885c84 100644
--- a/arch/arm/mach-imx/platsmp.c
+++ b/arch/arm/mach-imx/platsmp.c
@@ -92,5 +92,6 @@ struct smp_operations  imx_smp_ops __initdata = {
 	.smp_boot_secondary	= imx_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= imx_cpu_die,
+	.cpu_kill		= imx_cpu_kill,
 #endif
 };
diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
index a17543da602..ee42d20cba1 100644
--- a/arch/arm/mach-imx/pm-imx6q.c
+++ b/arch/arm/mach-imx/pm-imx6q.c
@@ -41,6 +41,7 @@ static int imx6q_pm_enter(suspend_state_t state)
 		cpu_suspend(0, imx6q_suspend_finish);
 		imx_smp_prepare();
 		imx_gpc_post_resume();
+		imx6q_set_lpm(WAIT_CLOCKED);
 		break;
 	default:
 		return -EINVAL;
diff --git a/arch/arm/mach-integrator/pci_v3.c b/arch/arm/mach-integrator/pci_v3.c
index be50e795536..e7fcea7f330 100644
--- a/arch/arm/mach-integrator/pci_v3.c
+++ b/arch/arm/mach-integrator/pci_v3.c
@@ -475,13 +475,12 @@ int __init pci_v3_setup(int nr, struct pci_sys_data *sys)
 {
 	int ret = 0;
 
+	if (!ap_syscon_base)
+		return -EINVAL;
+
 	if (nr == 0) {
 		sys->mem_offset = PHYS_PCI_MEM_BASE;
 		ret = pci_v3_setup_resources(sys);
-		/* Remap the Integrator system controller */
-		ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100);
-		if (!ap_syscon_base)
-			return -EINVAL;
 	}
 
 	return ret;
@@ -497,6 +496,13 @@ void __init pci_v3_preinit(void)
 	unsigned int temp;
 	int ret;
 
+	/* Remap the Integrator system controller */
+	ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100);
+	if (!ap_syscon_base) {
+		pr_err("unable to remap the AP syscon for PCIv3\n");
+		return;
+	}
+
 	pcibios_min_mem = 0x00100000;
 
 	/*
diff --git a/arch/arm/mach-kirkwood/board-ns2.c b/arch/arm/mach-kirkwood/board-ns2.c
index 8821720ab5a..f4632a809f6 100644
--- a/arch/arm/mach-kirkwood/board-ns2.c
+++ b/arch/arm/mach-kirkwood/board-ns2.c
@@ -18,47 +18,11 @@
 #include <linux/gpio.h>
 #include <linux/of.h>
 #include "common.h"
-#include "mpp.h"
 
 static struct mv643xx_eth_platform_data ns2_ge00_data = {
 	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
 };
 
-static unsigned int ns2_mpp_config[] __initdata = {
-	MPP0_SPI_SCn,
-	MPP1_SPI_MOSI,
-	MPP2_SPI_SCK,
-	MPP3_SPI_MISO,
-	MPP4_NF_IO6,
-	MPP5_NF_IO7,
-	MPP6_SYSRST_OUTn,
-	MPP7_GPO,		/* Fan speed (bit 1) */
-	MPP8_TW0_SDA,
-	MPP9_TW0_SCK,
-	MPP10_UART0_TXD,
-	MPP11_UART0_RXD,
-	MPP12_GPO,		/* Red led */
-	MPP14_GPIO,		/* USB fuse */
-	MPP16_GPIO,		/* SATA 0 power */
-	MPP17_GPIO,		/* SATA 1 power */
-	MPP18_NF_IO0,
-	MPP19_NF_IO1,
-	MPP20_SATA1_ACTn,
-	MPP21_SATA0_ACTn,
-	MPP22_GPIO,		/* Fan speed (bit 0) */
-	MPP23_GPIO,		/* Fan power */
-	MPP24_GPIO,		/* USB mode select */
-	MPP25_GPIO,		/* Fan rotation fail */
-	MPP26_GPIO,		/* USB device vbus */
-	MPP28_GPIO,		/* USB enable host vbus */
-	MPP29_GPIO,		/* Blue led (slow register) */
-	MPP30_GPIO,		/* Blue led (command register) */
-	MPP31_GPIO,		/* Board power off */
-	MPP32_GPIO,		/* Power button (0 = Released, 1 = Pushed) */
-	MPP33_GPO,		/* Fan speed (bit 2) */
-	0
-};
-
 #define NS2_GPIO_POWER_OFF	31
 
 static void ns2_power_off(void)
@@ -71,8 +35,6 @@ void __init ns2_init(void)
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
-	kirkwood_mpp_conf(ns2_mpp_config);
-
 	if (of_machine_is_compatible("lacie,netspace_lite_v2") ||
 	    of_machine_is_compatible("lacie,netspace_mini_v2"))
 		ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index 5dcb369b58a..99df4df680f 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -1,6 +1,8 @@
 ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \
 	-I$(srctree)/arch/arm/plat-orion/include
 
+AFLAGS_coherency_ll.o		:= -Wa,-march=armv7-a
+
 obj-y += system-controller.o
 obj-$(CONFIG_MACH_ARMADA_370_XP) += armada-370-xp.o irq-armada-370-xp.o addr-map.o coherency.o coherency_ll.o pmsu.o
 obj-$(CONFIG_SMP)                += platsmp.o headsmp.o
diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index 24d2f2df11a..ecd3f2a61bd 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -7,6 +7,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
+#include <linux/irq.h>
 #include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -23,6 +24,8 @@
 
 #include <linux/platform_data/keypad-omap.h>
 #include <linux/platform_data/lcd-mipid.h>
+#include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/i2c-cbus-gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -212,6 +215,45 @@ static inline void nokia770_mmc_init(void)
 }
 #endif
 
+#if defined(CONFIG_I2C_CBUS_GPIO) || defined(CONFIG_I2C_CBUS_GPIO_MODULE)
+static struct i2c_cbus_platform_data nokia770_cbus_data = {
+	.clk_gpio = OMAP_MPUIO(9),
+	.dat_gpio = OMAP_MPUIO(10),
+	.sel_gpio = OMAP_MPUIO(11),
+};
+
+static struct platform_device nokia770_cbus_device = {
+	.name   = "i2c-cbus-gpio",
+	.id     = 2,
+	.dev    = {
+		.platform_data = &nokia770_cbus_data,
+	},
+};
+
+static struct i2c_board_info nokia770_i2c_board_info_2[] __initdata = {
+	{
+		I2C_BOARD_INFO("retu-mfd", 0x01),
+	},
+};
+
+static void __init nokia770_cbus_init(void)
+{
+	const int retu_irq_gpio = 62;
+
+	if (gpio_request_one(retu_irq_gpio, GPIOF_IN, "Retu IRQ"))
+		return;
+	irq_set_irq_type(gpio_to_irq(retu_irq_gpio), IRQ_TYPE_EDGE_RISING);
+	nokia770_i2c_board_info_2[0].irq = gpio_to_irq(retu_irq_gpio);
+	i2c_register_board_info(2, nokia770_i2c_board_info_2,
+				ARRAY_SIZE(nokia770_i2c_board_info_2));
+	platform_device_register(&nokia770_cbus_device);
+}
+#else /* CONFIG_I2C_CBUS_GPIO */
+static void __init nokia770_cbus_init(void)
+{
+}
+#endif /* CONFIG_I2C_CBUS_GPIO */
+
 static void __init omap_nokia770_init(void)
 {
 	/* On Nokia 770, the SleepX signal is masked with an
@@ -233,6 +275,7 @@ static void __init omap_nokia770_init(void)
 	mipid_dev_init();
 	omap1_usb_init(&nokia770_usb_config);
 	nokia770_mmc_init();
+	nokia770_cbus_init();
 }
 
 MACHINE_START(NOKIA770, "Nokia 770")
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 41b581fd021..d4e4f9590a9 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -165,12 +165,6 @@ config MACH_OMAP_H4
 	select OMAP_DEBUG_DEVICES
 	select OMAP_PACKAGE_ZAF
 
-config MACH_OMAP_APOLLON
-	bool "OMAP 2420 Apollon board"
-	depends on SOC_OMAP2420
-	default y
-	select OMAP_PACKAGE_ZAC
-
 config MACH_OMAP_2430SDP
 	bool "OMAP 2430 SDP board"
 	depends on SOC_OMAP2430
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 947cafe65ae..0c66759a117 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -220,7 +220,6 @@ endif
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
 obj-$(CONFIG_MACH_OMAP_2430SDP)		+= board-2430sdp.o
-obj-$(CONFIG_MACH_OMAP_APOLLON)		+= board-apollon.o
 obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o
 obj-$(CONFIG_MACH_DEVKIT8000)     	+= board-devkit8000.o
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 51b96a1206d..82805de8005 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -20,12 +20,18 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/gpio.h>
+#include <linux/mfd/tps65910.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
 #include "common.h"
+#include "common-board-devices.h"
+#include "board-flash.h"
 
 #include "am35xx-emac.h"
 #include "mux.h"
@@ -36,6 +42,7 @@
 
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
+	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #endif
@@ -51,6 +58,54 @@ static struct usbhs_omap_board_data usbhs_bdata __initdata = {
 	.reset_gpio_port[2]  = -EINVAL
 };
 
+static struct mtd_partition crane_nand_partitions[] = {
+	{
+		.name		= "X-Loader",
+		.offset		= 0,
+		.size		= 4 * NAND_BLOCK_SIZE,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	{
+		.name		= "U-Boot",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 14 * NAND_BLOCK_SIZE,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	{
+		.name		= "U-Boot Env",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 2 * NAND_BLOCK_SIZE,
+	},
+	{
+		.name		= "Kernel",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 40 * NAND_BLOCK_SIZE,
+	},
+	{
+		.name		= "File System",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct tps65910_board tps65910_pdata = {
+	.irq = 7 + OMAP_INTC_START,
+	.en_ck32k_xtal = true,
+};
+
+static struct i2c_board_info __initdata tps65910_board_info[] = {
+	{
+		I2C_BOARD_INFO("tps65910", 0x2d),
+		.platform_data = &tps65910_pdata,
+	},
+};
+
+static void __init am3517_crane_i2c_init(void)
+{
+	omap_register_i2c_bus(1, 2600, tps65910_board_info,
+			ARRAY_SIZE(tps65910_board_info));
+}
+
 static void __init am3517_crane_init(void)
 {
 	int ret;
@@ -58,6 +113,10 @@ static void __init am3517_crane_init(void)
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
+	board_nand_init(crane_nand_partitions,
+			ARRAY_SIZE(crane_nand_partitions), 0,
+			NAND_BUSWIDTH_16, NULL);
+	am3517_crane_i2c_init();
 
 	/* Configure GPIO for EHCI port */
 	if (omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT)) {
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
deleted file mode 100644
index 5d0a61f5416..00000000000
--- a/arch/arm/mach-omap2/board-apollon.c
+++ /dev/null
@@ -1,342 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-apollon.c
- *
- * Copyright (C) 2005,2006 Samsung Electronics
- * Author: Kyungmin Park <kyungmin.park@samsung.com>
- *
- * Modified from mach-omap/omap2/board-h4.c
- *
- * Code for apollon OMAP2 board. Should work on many OMAP2 systems where
- * the bootloader passes the board-specific data to the kernel.
- * Do not put any board specific code to this file; create a new machine
- * type if you need custom low-level initializations.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/onenand.h>
-#include <linux/delay.h>
-#include <linux/leds.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/smc91x.h>
-#include <linux/gpio.h>
-#include <linux/platform_data/leds-omap.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-
-#include <video/omapdss.h>
-#include <video/omap-panel-generic-dpi.h>
-
-#include "mux.h"
-#include "control.h"
-
-/* LED & Switch macros */
-#define LED0_GPIO13		13
-#define LED1_GPIO14		14
-#define LED2_GPIO15		15
-#define SW_ENTER_GPIO16		16
-#define SW_UP_GPIO17		17
-#define SW_DOWN_GPIO58		58
-
-#define APOLLON_FLASH_CS	0
-#define APOLLON_ETH_CS		1
-#define APOLLON_ETHR_GPIO_IRQ	74
-
-static struct mtd_partition apollon_partitions[] = {
-	{
-		.name		= "X-Loader + U-Boot",
-		.offset		= 0,
-		.size		= SZ_128K,
-		.mask_flags	= MTD_WRITEABLE,
-	},
-	{
-		.name		= "params",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_128K,
-	},
-	{
-		.name		= "kernel",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_2M,
-	},
-	{
-		.name		= "rootfs",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_16M,
-	},
-	{
-		.name		= "filesystem00",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_32M,
-	},
-	{
-		.name		= "filesystem01",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct onenand_platform_data apollon_flash_data = {
-	.parts		= apollon_partitions,
-	.nr_parts	= ARRAY_SIZE(apollon_partitions),
-};
-
-static struct resource apollon_flash_resource[] = {
-	[0] = {
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device apollon_onenand_device = {
-	.name		= "onenand-flash",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &apollon_flash_data,
-	},
-	.num_resources	= ARRAY_SIZE(apollon_flash_resource),
-	.resource	= apollon_flash_resource,
-};
-
-static void __init apollon_flash_init(void)
-{
-	unsigned long base;
-
-	if (gpmc_cs_request(APOLLON_FLASH_CS, SZ_128K, &base) < 0) {
-		printk(KERN_ERR "Cannot request OneNAND GPMC CS\n");
-		return;
-	}
-	apollon_flash_resource[0].start = base;
-	apollon_flash_resource[0].end   = base + SZ_128K - 1;
-}
-
-static struct smc91x_platdata appolon_smc91x_info = {
-	.flags	= SMC91X_USE_16BIT | SMC91X_NOWAIT,
-	.leda	= RPC_LED_100_10,
-	.ledb	= RPC_LED_TX_RX,
-};
-
-static struct resource apollon_smc91x_resources[] = {
-	[0] = {
-		.flags  = IORESOURCE_MEM,
-	},
-	[1] = {
-		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
-	},
-};
-
-static struct platform_device apollon_smc91x_device = {
-	.name		= "smc91x",
-	.id		= -1,
-	.dev	= {
-		.platform_data	= &appolon_smc91x_info,
-	},
-	.num_resources	= ARRAY_SIZE(apollon_smc91x_resources),
-	.resource	= apollon_smc91x_resources,
-};
-
-static struct omap_led_config apollon_led_config[] = {
-	{
-		.cdev	= {
-			.name	= "apollon:led0",
-		},
-		.gpio	= LED0_GPIO13,
-	},
-	{
-		.cdev	= {
-			.name	= "apollon:led1",
-		},
-		.gpio	= LED1_GPIO14,
-	},
-	{
-		.cdev	= {
-			.name	= "apollon:led2",
-		},
-		.gpio	= LED2_GPIO15,
-	},
-};
-
-static struct omap_led_platform_data apollon_led_data = {
-	.nr_leds	= ARRAY_SIZE(apollon_led_config),
-	.leds		= apollon_led_config,
-};
-
-static struct platform_device apollon_led_device = {
-	.name		= "omap-led",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &apollon_led_data,
-	},
-};
-
-static struct platform_device *apollon_devices[] __initdata = {
-	&apollon_onenand_device,
-	&apollon_smc91x_device,
-	&apollon_led_device,
-};
-
-static inline void __init apollon_init_smc91x(void)
-{
-	unsigned long base;
-
-	unsigned int rate;
-	struct clk *gpmc_fck;
-	int eth_cs;
-	int err;
-
-	gpmc_fck = clk_get(NULL, "gpmc_fck");	/* Always on ENABLE_ON_INIT */
-	if (IS_ERR(gpmc_fck)) {
-		WARN_ON(1);
-		return;
-	}
-
-	clk_prepare_enable(gpmc_fck);
-	rate = clk_get_rate(gpmc_fck);
-
-	eth_cs = APOLLON_ETH_CS;
-
-	/* Make sure CS1 timings are correct */
-	gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
-
-	if (rate >= 160000000) {
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
-	} else if (rate >= 130000000) {
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
-	} else {/* rate = 100000000 */
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
-		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
-	}
-
-	if (gpmc_cs_request(APOLLON_ETH_CS, SZ_16M, &base) < 0) {
-		printk(KERN_ERR "Failed to request GPMC CS for smc91x\n");
-		goto out;
-	}
-	apollon_smc91x_resources[0].start = base + 0x300;
-	apollon_smc91x_resources[0].end   = base + 0x30f;
-	udelay(100);
-
-	omap_mux_init_gpio(APOLLON_ETHR_GPIO_IRQ, 0);
-	err = gpio_request_one(APOLLON_ETHR_GPIO_IRQ, GPIOF_IN, "SMC91x irq");
-	if (err) {
-		printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
-			APOLLON_ETHR_GPIO_IRQ);
-		gpmc_cs_free(APOLLON_ETH_CS);
-	}
-out:
-	clk_disable_unprepare(gpmc_fck);
-	clk_put(gpmc_fck);
-}
-
-static struct panel_generic_dpi_data apollon_panel_data = {
-	.name			= "apollon",
-};
-
-static struct omap_dss_device apollon_lcd_device = {
-	.name			= "lcd",
-	.driver_name		= "generic_dpi_panel",
-	.type			= OMAP_DISPLAY_TYPE_DPI,
-	.phy.dpi.data_lines	= 18,
-	.data			= &apollon_panel_data,
-};
-
-static struct omap_dss_device *apollon_dss_devices[] = {
-	&apollon_lcd_device,
-};
-
-static struct omap_dss_board_info apollon_dss_data = {
-	.num_devices	= ARRAY_SIZE(apollon_dss_devices),
-	.devices	= apollon_dss_devices,
-	.default_device	= &apollon_lcd_device,
-};
-
-static struct gpio apollon_gpio_leds[] __initdata = {
-	{ LED0_GPIO13, GPIOF_OUT_INIT_LOW, "LED0" }, /* LED0 - AA10 */
-	{ LED1_GPIO14, GPIOF_OUT_INIT_LOW, "LED1" }, /* LED1 - AA6  */
-	{ LED2_GPIO15, GPIOF_OUT_INIT_LOW, "LED2" }, /* LED2 - AA4  */
-};
-
-static void __init apollon_led_init(void)
-{
-	omap_mux_init_signal("vlynq_clk.gpio_13", 0);
-	omap_mux_init_signal("vlynq_rx1.gpio_14", 0);
-	omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
-
-	gpio_request_array(apollon_gpio_leds, ARRAY_SIZE(apollon_gpio_leds));
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init omap_apollon_init(void)
-{
-	u32 v;
-
-	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
-
-	apollon_init_smc91x();
-	apollon_led_init();
-	apollon_flash_init();
-
-	/* REVISIT: where's the correct place */
-	omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);
-
-	/* LCD PWR_EN */
-	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
-
-	/* Use Internal loop-back in MMC/SDIO Module Input Clock selection */
-	v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
-	v |= (1 << 24);
-	omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
-
-	/*
- 	 * Make sure the serial ports are muxed on at this point.
-	 * You have to mux them off in device drivers later on
-	 * if not needed.
-	 */
-	apollon_smc91x_resources[1].start = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
-	apollon_smc91x_resources[1].end = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
-	platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
-	omap_serial_init();
-	omap_sdrc_init(NULL, NULL);
-	omap_display_init(&apollon_dss_data);
-}
-
-MACHINE_START(OMAP_APOLLON, "OMAP24xx Apollon")
-	/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap242x_map_io,
-	.init_early	= omap2420_init_early,
-	.init_irq	= omap2_init_irq,
-	.handle_irq	= omap2_intc_handle_irq,
-	.init_machine	= omap_apollon_init,
-	.init_late	= omap2420_init_late,
-	.timer		= &omap2_timer,
-	.restart	= omap2xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c
index ebbc2adb499..792d6841790 100644
--- a/arch/arm/mach-omap2/board-cm-t3517.c
+++ b/arch/arm/mach-omap2/board-cm-t3517.c
@@ -32,6 +32,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
+#include <linux/mmc/host.h>
 #include <linux/can/platform/ti_hecc.h>
 
 #include <asm/mach-types.h>
@@ -46,6 +47,7 @@
 
 #include "mux.h"
 #include "control.h"
+#include "hsmmc.h"
 #include "common-board-devices.h"
 #include "am35xx-emac.h"
 #include "gpmc-nand.h"
@@ -121,6 +123,26 @@ static void cm_t3517_init_hecc(void)
 static inline void cm_t3517_init_hecc(void) {}
 #endif
 
+#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
+static struct omap2_hsmmc_info cm_t3517_mmc[] = {
+	{
+		.mmc		= 1,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= 144,
+		.gpio_wp	= 59,
+	},
+	{
+		.mmc		= 2,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+	},
+	{}	/* Terminator */
+};
+#else
+#define cm_t3517_mmc NULL
+#endif
+
 #if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE)
 #define RTC_IO_GPIO		(153)
 #define RTC_WR_GPIO		(154)
@@ -271,6 +293,10 @@ static struct omap_board_mux board_mux[] __initdata = {
 	/* CM-T3517 USB HUB nRESET */
 	OMAP3_MUX(MCBSP4_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
 
+	/* CD - GPIO144 and WP - GPIO59 for MMC1 - SB-T35 */
+	OMAP3_MUX(UART2_CTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(GPMC_CLK, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
+
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #endif
@@ -286,6 +312,7 @@ static void __init cm_t3517_init(void)
 	cm_t3517_init_usbh();
 	cm_t3517_init_hecc();
 	am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1);
+	omap_hsmmc_init(cm_t3517_mmc);
 }
 
 MACHINE_START(CM_T3517, "Compulab CM-T3517")
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 0f24cb84ba5..1921541a727 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -300,20 +300,20 @@ static struct omap2_hsmmc_info mmc[] = {
 
 static struct gpio_led igep_gpio_leds[] = {
 	[0] = {
-		.name			= "gpio-led:red:d0",
-		.default_trigger	= "default-off"
+		.name			= "omap3:red:user0",
+		.default_state		= 0,
 	},
 	[1] = {
-		.name			= "gpio-led:green:d0",
-		.default_trigger	= "default-off",
+		.name			= "omap3:green:boot",
+		.default_state		= 1,
 	},
 	[2] = {
-		.name			= "gpio-led:red:d1",
-		.default_trigger	= "default-off",
+		.name			= "omap3:red:user1",
+		.default_state		= 0,
 	},
 	[3] = {
-		.name			= "gpio-led:green:d1",
-		.default_trigger	= "heartbeat",
+		.name			= "omap3:green:user1",
+		.default_state		= 0,
 		.gpio			= -EINVAL, /* gets replaced */
 		.active_low		= 1,
 	},
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 5c8e9cee2c2..769c1feee1c 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -397,6 +397,12 @@ static struct omap_board_mux board_mux[] __initdata = {
 		  OMAP_PULL_ENA),
 	OMAP4_MUX(ABE_MCBSP1_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
 
+	/* UART2 - BT/FM/GPS shared transport */
+	OMAP4_MUX(UART2_CTS,	OMAP_PIN_INPUT	| OMAP_MUX_MODE0),
+	OMAP4_MUX(UART2_RTS,	OMAP_PIN_OUTPUT	| OMAP_MUX_MODE0),
+	OMAP4_MUX(UART2_RX,	OMAP_PIN_INPUT	| OMAP_MUX_MODE0),
+	OMAP4_MUX(UART2_TX,	OMAP_PIN_OUTPUT	| OMAP_MUX_MODE0),
+
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index cf07e289b4e..07a9ca8eda9 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -162,30 +162,39 @@ static struct tsl2563_platform_data rx51_tsl2563_platform_data = {
 #if defined(CONFIG_LEDS_LP5523) || defined(CONFIG_LEDS_LP5523_MODULE)
 static struct lp5523_led_config rx51_lp5523_led_config[] = {
 	{
+		.name		= "lp5523:kb1",
 		.chan_nr	= 0,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb2",
 		.chan_nr	= 1,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb3",
 		.chan_nr	= 2,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb4",
 		.chan_nr	= 3,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:b",
 		.chan_nr	= 4,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:g",
 		.chan_nr	= 5,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:r",
 		.chan_nr	= 6,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb5",
 		.chan_nr	= 7,
 		.led_current	= 50,
 	}, {
+		.name		= "lp5523:kb6",
 		.chan_nr	= 8,
 		.led_current	= 50,
 	}
@@ -1253,6 +1262,16 @@ static void __init rx51_init_lirc(void)
 }
 #endif
 
+static struct platform_device madc_hwmon = {
+	.name	= "twl4030_madc_hwmon",
+	.id	= -1,
+};
+
+static void __init rx51_init_twl4030_hwmon(void)
+{
+	platform_device_register(&madc_hwmon);
+}
+
 void __init rx51_peripherals_init(void)
 {
 	rx51_i2c_init();
@@ -1272,5 +1291,6 @@ void __init rx51_peripherals_init(void)
 		omap_hsmmc_init(mmc);
 
 	rx51_charger_init();
+	rx51_init_twl4030_hwmon();
 }
 
diff --git a/arch/arm/mach-omap2/cclock2420_data.c b/arch/arm/mach-omap2/cclock2420_data.c
index 7e5febe456d..ab7e952d207 100644
--- a/arch/arm/mach-omap2/cclock2420_data.c
+++ b/arch/arm/mach-omap2/cclock2420_data.c
@@ -1935,6 +1935,8 @@ int __init omap2420_clk_init(void)
 			omap2_init_clk_hw_omap_clocks(c->lk.clk);
 	}
 
+	omap2xxx_clkt_vps_late_init();
+
 	omap2_clk_disable_autoidle_all();
 
 	omap2_clk_enable_init_clocks(enable_init_clks,
diff --git a/arch/arm/mach-omap2/cclock2430_data.c b/arch/arm/mach-omap2/cclock2430_data.c
index eda079b96c6..eb3dab68d53 100644
--- a/arch/arm/mach-omap2/cclock2430_data.c
+++ b/arch/arm/mach-omap2/cclock2430_data.c
@@ -2050,6 +2050,8 @@ int __init omap2430_clk_init(void)
 			omap2_init_clk_hw_omap_clocks(c->lk.clk);
 	}
 
+	omap2xxx_clkt_vps_late_init();
+
 	omap2_clk_disable_autoidle_all();
 
 	omap2_clk_enable_init_clocks(enable_init_clks,
diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
index 5789a5e2556..a2cc046b47f 100644
--- a/arch/arm/mach-omap2/cclock44xx_data.c
+++ b/arch/arm/mach-omap2/cclock44xx_data.c
@@ -2026,14 +2026,13 @@ int __init omap4xxx_clk_init(void)
 	 * On OMAP4460 the ABE DPLL fails to turn on if in idle low-power
 	 * state when turning the ABE clock domain. Workaround this by
 	 * locking the ABE DPLL on boot.
+	 * Lock the ABE DPLL in any case to avoid issues with audio.
 	 */
-	if (cpu_is_omap446x()) {
-		rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck);
-		if (!rc)
-			rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ);
-		if (rc)
-			pr_err("%s: failed to configure ABE DPLL!\n", __func__);
-	}
+	rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck);
+	if (!rc)
+		rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ);
+	if (rc)
+		pr_err("%s: failed to configure ABE DPLL!\n", __func__);
 
 	return 0;
 }
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 5e304d0719a..626f3ea3142 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -639,7 +639,7 @@ static int count_ocp2scp_devices(struct omap_ocp2scp_dev *ocp2scp_dev)
 	return cnt;
 }
 
-static void omap_init_ocp2scp(void)
+static void __init omap_init_ocp2scp(void)
 {
 	struct omap_hwmod	*oh;
 	struct platform_device	*pdev;
diff --git a/arch/arm/mach-omap2/drm.c b/arch/arm/mach-omap2/drm.c
index 4c7566c7e24..2a2cfa88ddb 100644
--- a/arch/arm/mach-omap2/drm.c
+++ b/arch/arm/mach-omap2/drm.c
@@ -25,6 +25,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/platform_data/omap_drm.h>
 
+#include "soc.h"
 #include "omap_device.h"
 #include "omap_hwmod.h"
 
@@ -56,7 +57,7 @@ static int __init omap_init_drm(void)
 			oh->name);
 	}
 
-	platform_data.omaprev = GET_OMAP_REVISION();
+	platform_data.omaprev = GET_OMAP_TYPE;
 
 	return platform_device_register(&omap_drm_device);
 
diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
index 8033cb747c8..609c0913b0f 100644
--- a/arch/arm/mach-omap2/gpmc.c
+++ b/arch/arm/mach-omap2/gpmc.c
@@ -783,9 +783,6 @@ static int gpmc_mem_init(void)
 	 * even if we didn't boot from ROM.
 	 */
 	boot_rom_space = BOOT_ROM_SPACE;
-	/* In apollon the CS0 is mapped as 0x0000 0000 */
-	if (machine_is_omap_apollon())
-		boot_rom_space = 0;
 	gpmc_mem_root.start = GPMC_MEM_START + boot_rom_space;
 	gpmc_mem_root.end = GPMC_MEM_END;
 
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index 129d5081ed1..793f54ac7d1 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -2132,8 +2132,12 @@ static struct omap_hwmod omap44xx_mcpdm_hwmod = {
 	 * currently reset very early during boot, before I2C is
 	 * available, so it doesn't seem that we have any choice in
 	 * the kernel other than to avoid resetting it.
+	 *
+	 * Also, McPDM needs to be configured to NO_IDLE mode when it
+	 * is in used otherwise vital clocks will be gated which
+	 * results 'slow motion' audio playback.
 	 */
-	.flags		= HWMOD_EXT_OPT_MAIN_CLK,
+	.flags		= HWMOD_EXT_OPT_MAIN_CLK | HWMOD_SWSUP_SIDLE,
 	.mpu_irqs	= omap44xx_mcpdm_irqs,
 	.sdma_reqs	= omap44xx_mcpdm_sdma_reqs,
 	.main_clk	= "mcpdm_fck",
diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index 691aa674665..b8ad6e632bb 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -165,15 +165,11 @@ static struct device_node * __init omap_get_timer_dt(struct of_device_id *match,
 	struct device_node *np;
 
 	for_each_matching_node(np, match) {
-		if (!of_device_is_available(np)) {
-			of_node_put(np);
+		if (!of_device_is_available(np))
 			continue;
-		}
 
-		if (property && !of_get_property(np, property, NULL)) {
-			of_node_put(np);
+		if (property && !of_get_property(np, property, NULL))
 			continue;
-		}
 
 		of_add_property(np, &device_disabled);
 		return np;
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
index 553059f5184..755c0bb119f 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
@@ -47,7 +47,7 @@ static struct spi_board_info wm1253_devs[] = {
 		.bus_num	= 0,
 		.chip_select	= 0,
 		.mode		= SPI_MODE_0,
-		.irq		= S3C_EINT(5),
+		.irq		= S3C_EINT(4),
 		.controller_data = &wm0010_spi_csinfo,
 		.platform_data = &wm0010_pdata,
 	},
diff --git a/arch/arm/mach-s3c64xx/pm.c b/arch/arm/mach-s3c64xx/pm.c
index 7feb426fc20..d2e1a16690b 100644
--- a/arch/arm/mach-s3c64xx/pm.c
+++ b/arch/arm/mach-s3c64xx/pm.c
@@ -338,8 +338,10 @@ int __init s3c64xx_pm_init(void)
 	for (i = 0; i < ARRAY_SIZE(s3c64xx_pm_domains); i++)
 		pm_genpd_init(&s3c64xx_pm_domains[i]->pd, NULL, false);
 
+#ifdef CONFIG_S3C_DEV_FB
 	if (dev_get_platdata(&s3c_device_fb.dev))
 		pm_genpd_add_device(&s3c64xx_pm_f.pd, &s3c_device_fb.dev);
+#endif
 
 	return 0;
 }
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index 6b2fb87c869..076c26d4386 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -774,25 +774,27 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset,
 	size_t size, enum dma_data_direction dir,
 	void (*op)(const void *, size_t, int))
 {
+	unsigned long pfn;
+	size_t left = size;
+
+	pfn = page_to_pfn(page) + offset / PAGE_SIZE;
+	offset %= PAGE_SIZE;
+
 	/*
 	 * A single sg entry may refer to multiple physically contiguous
 	 * pages.  But we still need to process highmem pages individually.
 	 * If highmem is not configured then the bulk of this loop gets
 	 * optimized out.
 	 */
-	size_t left = size;
 	do {
 		size_t len = left;
 		void *vaddr;
 
+		page = pfn_to_page(pfn);
+
 		if (PageHighMem(page)) {
-			if (len + offset > PAGE_SIZE) {
-				if (offset >= PAGE_SIZE) {
-					page += offset / PAGE_SIZE;
-					offset %= PAGE_SIZE;
-				}
+			if (len + offset > PAGE_SIZE)
 				len = PAGE_SIZE - offset;
-			}
 			vaddr = kmap_high_get(page);
 			if (vaddr) {
 				vaddr += offset;
@@ -809,7 +811,7 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset,
 			op(vaddr, len, dir);
 		}
 		offset = 0;
-		page++;
+		pfn++;
 		left -= len;
 	} while (left);
 }
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 9f0610243bd..ce328c7f5c9 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -283,7 +283,7 @@ static struct mem_type mem_types[] = {
 	},
 	[MT_MEMORY_SO] = {
 		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
-				L_PTE_MT_UNCACHED,
+				L_PTE_MT_UNCACHED | L_PTE_XN,
 		.prot_l1   = PMD_TYPE_TABLE,
 		.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_SECT_S |
 				PMD_SECT_UNCACHED | PMD_SECT_XN,
diff --git a/arch/arm/plat-versatile/headsmp.S b/arch/arm/plat-versatile/headsmp.S
index dd703ef09b8..b178d44e9ea 100644
--- a/arch/arm/plat-versatile/headsmp.S
+++ b/arch/arm/plat-versatile/headsmp.S
@@ -20,7 +20,7 @@
  */
 ENTRY(versatile_secondary_startup)
 	mrc	p15, 0, r0, c0, c0, 5
-	and	r0, r0, #15
+	bic	r0, #0xff000000
 	adr	r4, 1f
 	ldmia	r4, {r5, r6}
 	sub	r4, r4, r5
diff --git a/arch/arm/vfp/entry.S b/arch/arm/vfp/entry.S
index cc926c98598..323ce1a62bb 100644
--- a/arch/arm/vfp/entry.S
+++ b/arch/arm/vfp/entry.S
@@ -22,7 +22,7 @@
 @  IRQs disabled.
 @
 ENTRY(do_vfp)
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	add	r11, r4, #1		@ increment it
 	str	r11, [r10, #TI_PREEMPT]
@@ -35,7 +35,7 @@ ENTRY(do_vfp)
 ENDPROC(do_vfp)
 
 ENTRY(vfp_null_entry)
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	get_thread_info	r10
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	sub	r11, r4, #1		@ decrement it
@@ -53,7 +53,7 @@ ENDPROC(vfp_null_entry)
 
 	__INIT
 ENTRY(vfp_testing_entry)
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	get_thread_info	r10
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	sub	r11, r4, #1		@ decrement it
diff --git a/arch/arm/vfp/vfphw.S b/arch/arm/vfp/vfphw.S
index ea0349f6358..dd5e56f95f3 100644
--- a/arch/arm/vfp/vfphw.S
+++ b/arch/arm/vfp/vfphw.S
@@ -168,7 +168,7 @@ vfp_hw_state_valid:
 					@ else it's one 32-bit instruction, so
 					@ always subtract 4 from the following
 					@ instruction address.
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	get_thread_info	r10
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	sub	r11, r4, #1		@ decrement it
@@ -192,7 +192,7 @@ look_for_VFP_exceptions:
 	@ not recognised by VFP
 
 	DBGSTR	"not VFP"
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	get_thread_info	r10
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	sub	r11, r4, #1		@ decrement it