diff options
author | Linus Torvalds <torvalds@linux-foundation.org> | 2011-07-25 21:00:19 -0700 |
---|---|---|
committer | Linus Torvalds <torvalds@linux-foundation.org> | 2011-07-25 21:00:19 -0700 |
commit | 45b583b10a8b438b970e95a7d1d4db22c9e35004 (patch) | |
tree | 14fa481598289df0459580c582b48a9d95db51f6 /arch/arm | |
parent | 154dd78d30b56ffb8b447f629bfcceb14150e5c4 (diff) | |
parent | f19da2ce8ef5e49b8b8ea199c3601dd45d71b262 (diff) |
Merge 'akpm' patch series
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
Diffstat (limited to 'arch/arm')
-rw-r--r-- | arch/arm/mach-ux500/board-u5500.c | 84 |
1 files changed, 83 insertions, 1 deletions
diff --git a/arch/arm/mach-ux500/board-u5500.c b/arch/arm/mach-ux500/board-u5500.c index 44fd3b5c33e..e58f0f56242 100644 --- a/arch/arm/mach-ux500/board-u5500.c +++ b/arch/arm/mach-ux500/board-u5500.c @@ -10,16 +10,97 @@ #include <linux/amba/bus.h> #include <linux/gpio.h> #include <linux/irq.h> +#include <linux/i2c.h> #include <asm/mach/arch.h> #include <asm/mach-types.h> +#include <plat/pincfg.h> +#include <plat/i2c.h> + #include <mach/hardware.h> #include <mach/devices.h> #include <mach/setup.h> +#include "pins-db5500.h" #include "devices-db5500.h" +#include <linux/led-lm3530.h> + +/* + * GPIO + */ + +static pin_cfg_t u5500_pins[] = { + /* I2C */ + GPIO218_I2C2_SCL | PIN_INPUT_PULLUP, + GPIO219_I2C2_SDA | PIN_INPUT_PULLUP, + + /* DISPLAY_ENABLE */ + GPIO226_GPIO | PIN_OUTPUT_LOW, + + /* Backlight Enbale */ + GPIO224_GPIO | PIN_OUTPUT_HIGH, +}; +/* + * I2C + */ + +#define U5500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, _sm) \ +static struct nmk_i2c_controller u5500_i2c##id##_data = { \ + /* \ + * slave data setup time, which is \ + * 250 ns,100ns,10ns which is 14,6,2 \ + * respectively for a 48 Mhz \ + * i2c clock \ + */ \ + .slsu = _slsu, \ + /* Tx FIFO threshold */ \ + .tft = _tft, \ + /* Rx FIFO threshold */ \ + .rft = _rft, \ + /* std. mode operation */ \ + .clk_freq = clk, \ + .sm = _sm, \ +} +/* + * The board uses TODO <3> i2c controllers, initialize all of + * them with slave data setup time of 250 ns, + * Tx & Rx FIFO threshold values as 1 and standard + * mode of operation + */ + +U5500_I2C_CONTROLLER(2, 0xe, 1, 1, 400000, I2C_FREQ_MODE_FAST); + +static struct lm3530_platform_data u5500_als_platform_data = { + .mode = LM3530_BL_MODE_MANUAL, + .als_input_mode = LM3530_INPUT_ALS1, + .max_current = LM3530_FS_CURR_26mA, + .pwm_pol_hi = true, + .als_avrg_time = LM3530_ALS_AVRG_TIME_512ms, + .brt_ramp_law = 1, /* Linear */ + .brt_ramp_fall = LM3530_RAMP_TIME_8s, + .brt_ramp_rise = LM3530_RAMP_TIME_8s, + .als1_resistor_sel = LM3530_ALS_IMPD_13_53kOhm, + .als2_resistor_sel = LM3530_ALS_IMPD_Z, + .als_vmin = 730, /* mV */ + .als_vmax = 1020, /* mV */ + .brt_val = 0x7F, /* Max brightness */ +}; + +static struct i2c_board_info __initdata u5500_i2c2_devices[] = { + { + /* Backlight */ + I2C_BOARD_INFO("lm3530-led", 0x36), + .platform_data = &u5500_als_platform_data, + }, +}; + +static void __init u5500_i2c_init(void) +{ + db5500_add_i2c2(&u5500_i2c2_data); + i2c_register_board_info(2, ARRAY_AND_SIZE(u5500_i2c2_devices)); +} static void __init u5500_uart_init(void) { db5500_add_uart0(NULL); @@ -30,7 +111,8 @@ static void __init u5500_uart_init(void) static void __init u5500_init_machine(void) { u5500_init_devices(); - + nmk_config_pins(u5500_pins, ARRAY_SIZE(u5500_pins)); + u5500_i2c_init(); u5500_sdi_init(); u5500_uart_init(); } |