diff options
| author | Ben Dooks <ben-linux@fluff.org> | 2009-05-17 22:32:23 +0100 |
|---|---|---|
| committer | Ben Dooks <ben-linux@fluff.org> | 2009-05-18 16:26:03 +0100 |
| commit | 070276d5d049f385763dee19112bea08f56c9a0d (patch) | |
| tree | 5a32a885de72f18476ff067a25d8a159ac01629d /arch/arm | |
| parent | 75cbcff3729fe2568dff38d16d6494f8fb7f59fe (diff) | |
[ARM] S3C24XX: GPIO: Change to macros for GPIO numbering
Prepare to remove the large number of S3C2410_GPxn defines
by moving to S3C2410_GPx(n) in arch/arm.
The following perl was used to change the files:
perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Diffstat (limited to 'arch/arm')
28 files changed, 185 insertions, 286 deletions
diff --git a/arch/arm/mach-s3c2400/gpio.c b/arch/arm/mach-s3c2400/gpio.c index 7a7ed4174c8..81ebe2f0990 100644 --- a/arch/arm/mach-s3c2400/gpio.c +++ b/arch/arm/mach-s3c2400/gpio.c @@ -33,10 +33,10 @@ int s3c2400_gpio_getirq(unsigned int pin) { - if (pin < S3C2410_GPE0 || pin > S3C2400_GPE7_EINT7) + if (pin < S3C2410_GPE(0) || pin > S3C2400_GPE7_EINT7) return -1; /* not valid interrupts */ - return (pin - S3C2410_GPE0) + IRQ_EINT0; + return (pin - S3C2410_GPE(0)) + IRQ_EINT0; } EXPORT_SYMBOL(s3c2400_gpio_getirq); diff --git a/arch/arm/mach-s3c2410/gpio.c b/arch/arm/mach-s3c2410/gpio.c index 36a3132f39e..bf7fbfe7e4d 100644 --- a/arch/arm/mach-s3c2410/gpio.c +++ b/arch/arm/mach-s3c2410/gpio.c @@ -39,12 +39,12 @@ int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, unsigned long flags; unsigned long val; - if (pin < S3C2410_GPG8 || pin > S3C2410_GPG15) + if (pin < S3C2410_GPG(8) || pin > S3C2410_GPG(15)) return -1; config &= 0xff; - pin -= S3C2410_GPG8; + pin -= S3C2410_GPG(8); reg += pin & ~3; local_irq_save(flags); diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c index 9bbea8a73dd..5aabf117cbb 100644 --- a/arch/arm/mach-s3c2410/h1940-bluetooth.c +++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c @@ -43,9 +43,9 @@ static void h1940bt_enable(int on) h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER); /* Reset the chip */ mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 1); + s3c2410_gpio_setpin(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 0); + s3c2410_gpio_setpin(S3C2410_GPH(1), 0); state = 1; } @@ -54,9 +54,9 @@ static void h1940bt_enable(int on) led_trigger_event(bt_led_trigger, 0); #endif - s3c2410_gpio_setpin(S3C2410_GPH1, 1); + s3c2410_gpio_setpin(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH1, 0); + s3c2410_gpio_setpin(S3C2410_GPH(1), 0); mdelay(10); h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0); @@ -89,14 +89,14 @@ static DEVICE_ATTR(enable, 0644, static int __init h1940bt_probe(struct platform_device *pdev) { /* Configures BT serial port GPIOs */ - s3c2410_gpio_cfgpin(S3C2410_GPH0, S3C2410_GPH0_nCTS0); - s3c2410_gpio_pullup(S3C2410_GPH0, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH1, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_pullup(S3C2410_GPH1, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH2, S3C2410_GPH2_TXD0); - s3c2410_gpio_pullup(S3C2410_GPH2, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH3, S3C2410_GPH3_RXD0); - s3c2410_gpio_pullup(S3C2410_GPH3, 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0); + s3c2410_gpio_pullup(S3C2410_GPH(0), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_pullup(S3C2410_GPH(1), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0); + s3c2410_gpio_pullup(S3C2410_GPH(2), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0); + s3c2410_gpio_pullup(S3C2410_GPH(3), 1); #ifdef CONFIG_LEDS_H1940 led_trigger_register_simple("h1940-bluetooth", &bt_led_trigger); diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-core.h b/arch/arm/mach-s3c2410/include/mach/gpio-core.h index 6c9fbb99ef1..8fe192081d3 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-core.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-core.h @@ -24,7 +24,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin) { struct s3c_gpio_chip *chip; - if (pin > S3C2410_GPG10) + if (pin > S3C2410_GPG(10)) return NULL; chip = &s3c24xx_gpios[pin/32]; diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-fns.h b/arch/arm/mach-s3c2410/include/mach/gpio-fns.h index b4f39558bed..801dff13858 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-fns.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-fns.h @@ -30,8 +30,8 @@ * set the configuration of the given pin to the value passed. * * eg: - * s3c2410_gpio_cfgpin(S3C2410_GPA0, S3C2410_GPA0_ADDR0); - * s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1); + * s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0); + * s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1); */ extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function); @@ -80,8 +80,8 @@ extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, * * eg; * - * s3c2410_gpio_pullup(S3C2410_GPB0, 0); - * s3c2410_gpio_pullup(S3C2410_GPE8, 0); + * s3c2410_gpio_pullup(S3C2410_GPB(0), 0); + * s3c2410_gpio_pullup(S3C2410_GPE(8), 0); */ extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to); diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h b/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h index 5213e453df1..2edbb9c88ab 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h @@ -68,5 +68,26 @@ enum s3c_gpio_number { #define S3C2410_GPG(_nr) (S3C2410_GPIO_G_START + (_nr)) #define S3C2410_GPH(_nr) (S3C2410_GPIO_H_START + (_nr)) +/* compatibility until drivers can be modified */ + +#define S3C2410_GPA0 S3C2410_GPA(0) +#define S3C2410_GPA1 S3C2410_GPA(1) +#define S3C2410_GPA3 S3C2410_GPA(3) +#define S3C2410_GPA7 S3C2410_GPA(7) + +#define S3C2410_GPE0 S3C2410_GPE(0) +#define S3C2410_GPE1 S3C2410_GPE(1) +#define S3C2410_GPE2 S3C2410_GPE(2) +#define S3C2410_GPE3 S3C2410_GPE(3) +#define S3C2410_GPE4 S3C2410_GPE(4) +#define S3C2410_GPE5 S3C2410_GPE(5) +#define S3C2410_GPE6 S3C2410_GPE(6) +#define S3C2410_GPE7 S3C2410_GPE(7) +#define S3C2410_GPE8 S3C2410_GPE(8) +#define S3C2410_GPE9 S3C2410_GPE(9) +#define S3C2410_GPE10 S3C2410_GPE(10) + +#define S3C2410_GPH10 S3C2410_GPH(10) + #endif /* __MACH_GPIONRS_H */ diff --git a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h index 90cefebd293..b278d0c45cc 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h @@ -69,81 +69,58 @@ #define S3C2400_GPACON S3C2410_GPIOREG(0x00) #define S3C2400_GPADAT S3C2410_GPIOREG(0x04) -#define S3C2410_GPA0 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 0) #define S3C2410_GPA0_ADDR0 (1<<0) -#define S3C2410_GPA1 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 1) #define S3C2410_GPA1_ADDR16 (1<<1) -#define S3C2410_GPA2 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 2) #define S3C2410_GPA2_ADDR17 (1<<2) -#define S3C2410_GPA3 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 3) #define S3C2410_GPA3_ADDR18 (1<<3) -#define S3C2410_GPA4 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 4) #define S3C2410_GPA4_ADDR19 (1<<4) -#define S3C2410_GPA5 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 5) #define S3C2410_GPA5_ADDR20 (1<<5) -#define S3C2410_GPA6 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 6) #define S3C2410_GPA6_ADDR21 (1<<6) -#define S3C2410_GPA7 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 7) #define S3C2410_GPA7_ADDR22 (1<<7) -#define S3C2410_GPA8 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 8) #define S3C2410_GPA8_ADDR23 (1<<8) -#define S3C2410_GPA9 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 9) #define S3C2410_GPA9_ADDR24 (1<<9) -#define S3C2410_GPA10 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 10) #define S3C2410_GPA10_ADDR25 (1<<10) #define S3C2400_GPA10_SCKE (1<<10) -#define S3C2410_GPA11 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 11) #define S3C2410_GPA11_ADDR26 (1<<11) #define S3C2400_GPA11_nCAS0 (1<<11) -#define S3C2410_GPA12 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 12) #define S3C2410_GPA12_nGCS1 (1<<12) #define S3C2400_GPA12_nCAS1 (1<<12) -#define S3C2410_GPA13 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 13) #define S3C2410_GPA13_nGCS2 (1<<13) #define S3C2400_GPA13_nGCS1 (1<<13) -#define S3C2410_GPA14 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 14) #define S3C2410_GPA14_nGCS3 (1<<14) #define S3C2400_GPA14_nGCS2 (1<<14) -#define S3C2410_GPA15 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 15) #define S3C2410_GPA15_nGCS4 (1<<15) #define S3C2400_GPA15_nGCS3 (1<<15) -#define S3C2410_GPA16 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 16) #define S3C2410_GPA16_nGCS5 (1<<16) #define S3C2400_GPA16_nGCS4 (1<<16) -#define S3C2410_GPA17 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 17) #define S3C2410_GPA17_CLE (1<<17) #define S3C2400_GPA17_nGCS5 (1<<17) -#define S3C2410_GPA18 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 18) #define S3C2410_GPA18_ALE (1<<18) -#define S3C2410_GPA19 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 19) #define S3C2410_GPA19_nFWE (1<<19) -#define S3C2410_GPA20 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 20) #define S3C2410_GPA20_nFRE (1<<20) -#define S3C2410_GPA21 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 21) #define S3C2410_GPA21_nRSTOUT (1<<21) -#define S3C2410_GPA22 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 22) #define S3C2410_GPA22_nFCE (1<<22) /* 0x08 and 0x0c are reserved on S3C2410 */ @@ -171,85 +148,69 @@ /* no i/o pin in port b can have value 3 (unless it is a s3c2443) ! */ -#define S3C2410_GPB0 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 0) #define S3C2410_GPB0_TOUT0 (0x02 << 0) #define S3C2400_GPB0_DATA16 (0x02 << 0) -#define S3C2410_GPB1 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 1) #define S3C2410_GPB1_TOUT1 (0x02 << 2) #define S3C2400_GPB1_DATA17 (0x02 << 2) -#define S3C2410_GPB2 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 2) #define S3C2410_GPB2_TOUT2 (0x02 << 4) #define S3C2400_GPB2_DATA18 (0x02 << 4) #define S3C2400_GPB2_TCLK1 (0x03 << 4) -#define S3C2410_GPB3 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 3) #define S3C2410_GPB3_TOUT3 (0x02 << 6) #define S3C2400_GPB3_DATA19 (0x02 << 6) #define S3C2400_GPB3_TXD1 (0x03 << 6) -#define S3C2410_GPB4 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 4) #define S3C2410_GPB4_TCLK0 (0x02 << 8) #define S3C2400_GPB4_DATA20 (0x02 << 8) #define S3C2410_GPB4_MASK (0x03 << 8) #define S3C2400_GPB4_RXD1 (0x03 << 8) #define S3C2400_GPB4_MASK (0x03 << 8) -#define S3C2410_GPB5 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 5) #define S3C2410_GPB5_nXBACK (0x02 << 10) #define S3C2443_GPB5_XBACK (0x03 << 10) #define S3C2400_GPB5_DATA21 (0x02 << 10) #define S3C2400_GPB5_nCTS1 (0x03 << 10) -#define S3C2410_GPB6 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 6) #define S3C2410_GPB6_nXBREQ (0x02 << 12) #define S3C2443_GPB6_XBREQ (0x03 << 12) #define S3C2400_GPB6_DATA22 (0x02 << 12) #define S3C2400_GPB6_nRTS1 (0x03 << 12) -#define S3C2410_GPB7 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 7) #define S3C2410_GPB7_nXDACK1 (0x02 << 14) #define S3C2443_GPB7_XDACK1 (0x03 << 14) #define S3C2400_GPB7_DATA23 (0x02 << 14) -#define S3C2410_GPB8 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 8) #define S3C2410_GPB8_nXDREQ1 (0x02 << 16) #define S3C2400_GPB8_DATA24 (0x02 << 16) -#define S3C2410_GPB9 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 9) #define S3C2410_GPB9_nXDACK0 (0x02 << 18) #define S3C2443_GPB9_XDACK0 (0x03 << 18) #define S3C2400_GPB9_DATA25 (0x02 << 18) #define S3C2400_GPB9_I2SSDI (0x03 << 18) -#define S3C2410_GPB10 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 10) #define S3C2410_GPB10_nXDRE0 (0x02 << 20) #define S3C2443_GPB10_XDREQ0 (0x03 << 20) #define S3C2400_GPB10_DATA26 (0x02 << 20) #define S3C2400_GPB10_nSS (0x03 << 20) -#define S3C2400_GPB11 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 11) #define S3C2400_GPB11_INP (0x00 << 22) #define S3C2400_GPB11_OUTP (0x01 << 22) #define S3C2400_GPB11_DATA27 (0x02 << 22) -#define S3C2400_GPB12 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 12) #define S3C2400_GPB12_INP (0x00 << 24) #define S3C2400_GPB12_OUTP (0x01 << 24) #define S3C2400_GPB12_DATA28 (0x02 << 24) -#define S3C2400_GPB13 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 13) #define S3C2400_GPB13_INP (0x00 << 26) #define S3C2400_GPB13_OUTP (0x01 << 26) #define S3C2400_GPB13_DATA29 (0x02 << 26) -#define S3C2400_GPB14 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 14) #define S3C2400_GPB14_INP (0x00 << 28) #define S3C2400_GPB14_OUTP (0x01 << 28) #define S3C2400_GPB14_DATA30 (0x02 << 28) -#define S3C2400_GPB15 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 15) #define S3C2400_GPB15_INP (0x00 << 30) #define S3C2400_GPB15_OUTP (0x01 << 30) #define S3C2400_GPB15_DATA31 (0x02 << 30) @@ -270,67 +231,51 @@ #define S3C2400_GPCDAT S3C2410_GPIOREG(0x18) #define S3C2400_GPCUP S3C2410_GPIOREG(0x1C) -#define S3C2410_GPC0 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 0) #define S3C2410_GPC0_LEND (0x02 << 0) #define S3C2400_GPC0_VD0 (0x02 << 0) -#define S3C2410_GPC1 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 1) #define S3C2410_GPC1_VCLK (0x02 << 2) #define S3C2400_GPC1_VD1 (0x02 << 2) -#define S3C2410_GPC2 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 2) #define S3C2410_GPC2_VLINE (0x02 << 4) #define S3C2400_GPC2_VD2 (0x02 << 4) -#define S3C2410_GPC3 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 3) #define S3C2410_GPC3_VFRAME (0x02 << 6) #define S3C2400_GPC3_VD3 (0x02 << 6) -#define S3C2410_GPC4 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 4) #define S3C2410_GPC4_VM (0x02 << 8) #define S3C2400_GPC4_VD4 (0x02 << 8) -#define S3C2410_GPC5 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 5) #define S3C2410_GPC5_LCDVF0 (0x02 << 10) #define S3C2400_GPC5_VD5 (0x02 << 10) -#define S3C2410_GPC6 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 6) #define S3C2410_GPC6_LCDVF1 (0x02 << 12) #define S3C2400_GPC6_VD6 (0x02 << 12) -#define S3C2410_GPC7 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 7) #define S3C2410_GPC7_LCDVF2 (0x02 << 14) #define S3C2400_GPC7_VD7 (0x02 << 14) -#define S3C2410_GPC8 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 8) #define S3C2410_GPC8_VD0 (0x02 << 16) #define S3C2400_GPC8_VD8 (0x02 << 16) -#define S3C2410_GPC9 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 9) #define S3C2410_GPC9_VD1 (0x02 << 18) #define S3C2400_GPC9_VD9 (0x02 << 18) -#define S3C2410_GPC10 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 10) #define S3C2410_GPC10_VD2 (0x02 << 20) #define S3C2400_GPC10_VD10 (0x02 << 20) -#define S3C2410_GPC11 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 11) #define S3C2410_GPC11_VD3 (0x02 << 22) #define S3C2400_GPC11_VD11 (0x02 << 22) -#define S3C2410_GPC12 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 12) #define S3C2410_GPC12_VD4 (0x02 << 24) #define S3C2400_GPC12_VD12 (0x02 << 24) -#define S3C2410_GPC13 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 13) #define S3C2410_GPC13_VD5 (0x02 << 26) #define S3C2400_GPC13_VD13 (0x02 << 26) -#define S3C2410_GPC14 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 14) #define S3C2410_GPC14_VD6 (0x02 << 28) #define S3C2400_GPC14_VD14 (0x02 << 28) -#define S3C2410_GPC15 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 15) #define S3C2410_GPC15_VD7 (0x02 << 30) #define S3C2400_GPC15_VD15 (0x02 << 30) @@ -355,67 +300,51 @@ #define S3C2400_GPDDAT S3C2410_GPIOREG(0x24) #define S3C2400_GPDUP S3C2410_GPIOREG(0x28) -#define S3C2410_GPD0 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 0) #define S3C2410_GPD0_VD8 (0x02 << 0) #define S3C2400_GPD0_VFRAME (0x02 << 0) #define S3C2442_GPD0_nSPICS1 (0x03 << 0) -#define S3C2410_GPD1 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 1) #define S3C2410_GPD1_VD9 (0x02 << 2) #define S3C2400_GPD1_VM (0x02 << 2) #define S3C2442_GPD1_SPICLK1 (0x03 << 2) -#define S3C2410_GPD2 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 2) #define S3C2410_GPD2_VD10 (0x02 << 4) #define S3C2400_GPD2_VLINE (0x02 << 4) -#define S3C2410_GPD3 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 3) #define S3C2410_GPD3_VD11 (0x02 << 6) #define S3C2400_GPD3_VCLK (0x02 << 6) -#define S3C2410_GPD4 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 4) #define S3C2410_GPD4_VD12 (0x02 << 8) #define S3C2400_GPD4_LEND (0x02 << 8) -#define S3C2410_GPD5 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 5) #define S3C2410_GPD5_VD13 (0x02 << 10) #define S3C2400_GPD5_TOUT0 (0x02 << 10) -#define S3C2410_GPD6 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 6) #define S3C2410_GPD6_VD14 (0x02 << 12) #define S3C2400_GPD6_TOUT1 (0x02 << 12) -#define S3C2410_GPD7 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 7) #define S3C2410_GPD7_VD15 (0x02 << 14) #define S3C2400_GPD7_TOUT2 (0x02 << 14) -#define S3C2410_GPD8 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 8) #define S3C2410_GPD8_VD16 (0x02 << 16) #define S3C2400_GPD8_TOUT3 (0x02 << 16) -#define S3C2410_GPD9 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 9) #define S3C2410_GPD9_VD17 (0x02 << 18) #define S3C2400_GPD9_TCLK0 (0x02 << 18) #define S3C2410_GPD9_MASK (0x03 << 18) -#define S3C2410_GPD10 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 10) #define S3C2410_GPD10_VD18 (0x02 << 20) #define S3C2400_GPD10_nWAIT (0x02 << 20) -#define S3C2410_GPD11 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 11) #define S3C2410_GPD11_VD19 (0x02 << 22) -#define S3C2410_GPD12 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 12) #define S3C2410_GPD12_VD20 (0x02 << 24) -#define S3C2410_GPD13 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 13) #define S3C2410_GPD13_VD21 (0x02 << 26) -#define S3C2410_GPD14 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 14) #define S3C2410_GPD14_VD22 (0x02 << 28) #define S3C2410_GPD14_nSS1 (0x03 << 28) -#define S3C2410_GPD15 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 15) #define S3C2410_GPD15_VD23 (0x02 << 30) #define S3C2410_GPD15_nSS0 (0x03 << 30) @@ -441,26 +370,22 @@ #define S3C2400_GPEDAT S3C2410_GPIOREG(0x30) #define S3C2400_GPEUP S3C2410_GPIOREG(0x34) -#define S3C2410_GPE0 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 0) #define S3C2410_GPE0_I2SLRCK (0x02 << 0) #define S3C2443_GPE0_AC_nRESET (0x03 << 0) #define S3C2400_GPE0_EINT0 (0x02 << 0) #define S3C2410_GPE0_MASK (0x03 << 0) -#define S3C2410_GPE1 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 1) #define S3C2410_GPE1_I2SSCLK (0x02 << 2) #define S3C2443_GPE1_AC_SYNC (0x03 << 2) #define S3C2400_GPE1_EINT1 (0x02 << 2) #define S3C2400_GPE1_nSS (0x03 << 2) #define S3C2410_GPE1_MASK (0x03 << 2) -#define S3C2410_GPE2 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 2) #define S3C2410_GPE2_CDCLK (0x02 << 4) #define S3C2443_GPE2_AC_BITCLK (0x03 << 4) #define S3C2400_GPE2_EINT2 (0x02 << 4) #define S3C2400_GPE2_I2SSDI (0x03 << 4) -#define S3C2410_GPE3 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 3) #define S3C2410_GPE3_I2SSDI (0x02 << 6) #define S3C2443_GPE3_AC_SDI (0x03 << 6) #define S3C2400_GPE3_EINT3 (0x02 << 6) @@ -468,7 +393,6 @@ #define S3C2410_GPE3_nSS0 (0x03 << 6) #define S3C2410_GPE3_MASK (0x03 << 6) -#define S3C2410_GPE4 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 4) #define S3C2410_GPE4_I2SSDO (0x02 << 8) #define S3C2443_GPE4_AC_SDO (0x03 << 8) #define S3C2400_GPE4_EINT4 (0x02 << 8) @@ -476,59 +400,48 @@ #define S3C2410_GPE4_I2SSDI (0x03 << 8) #define S3C2410_GPE4_MASK (0x03 << 8) -#define S3C2410_GPE5 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 5) #define S3C2410_GPE5_SDCLK (0x02 << 10) #define S3C2443_GPE5_SD1_CLK (0x02 << 10) #define S3C2400_GPE5_EINT5 (0x02 << 10) #define S3C2400_GPE5_TCLK1 (0x03 << 10) -#define S3C2410_GPE6 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 6) #define S3C2410_GPE6_SDCMD (0x02 << 12) #define S3C2443_GPE6_SD1_CMD (0x02 << 12) #define S3C2443_GPE6_AC_BITCLK (0x03 << 12) #define S3C2400_GPE6_EINT6 (0x02 << 12) -#define S3C2410_GPE7 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 7) #define S3C2410_GPE7_SDDAT0 (0x02 << 14) #define S3C2443_GPE5_SD1_DAT0 (0x02 << 14) #define S3C2443_GPE7_AC_SDI (0x03 << 14) #define S3C2400_GPE7_EINT7 (0x02 << 14) -#define S3C2410_GPE8 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 8) #define S3C2410_GPE8_SDDAT1 (0x02 << 16) #define S3C2443_GPE8_SD1_DAT1 (0x02 << 16) #define S3C2443_GPE8_AC_SDO (0x03 << 16) #define S3C2400_GPE8_nXDACK0 (0x02 << 16) -#define S3C2410_GPE9 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 9) #define S3C2410_GPE9_SDDAT2 (0x02 << 18) #define S3C2443_GPE9_SD1_DAT2 (0x02 << 18) #define S3C2443_GPE9_AC_SYNC (0x03 << 18) #define S3C2400_GPE9_nXDACK1 (0x02 << 18) #define S3C2400_GPE9_nXBACK (0x03 << 18) -#define S3C2410_GPE10 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 10) #define S3C2410_GPE10_SDDAT3 (0x02 << 20) #define S3C2443_GPE10_SD1_DAT3 (0x02 << 20) #define S3C2443_GPE10_AC_nRESET (0x03 << 20) #define S3C2400_GPE10_nXDREQ0 (0x02 << 20) -#define S3C2410_GPE11 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 11) #define S3C2410_GPE11_SPIMISO0 (0x02 << 22) #define S3C2400_GPE11_nXDREQ1 (0x02 << 22) #define S3C2400_GPE11_nXBREQ (0x03 << 22) -#define S3C2410_GPE12 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 12) #define S3C2410_GPE12_SPIMOSI0 (0x02 << 24) -#define S3C2410_GPE13 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 13) #define S3C2410_GPE13_SPICLK0 (0x02 << 26) -#define S3C2410_GPE14 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 14) #define S3C2410_GPE14_IICSCL (0x02 << 28) #define S3C2410_GPE14_MASK (0x03 << 28) -#define S3C2410_GPE15 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 15) #define S3C2410_GPE15_IICSDA (0x02 << 30) #define S3C2410_GPE15_MASK (0x03 << 30) @@ -564,39 +477,31 @@ #define S3C2400_GPFDAT S3C2410_GPIOREG(0x3C) #define S3C2400_GPFUP S3C2410_GPIOREG(0x40) -#define S3C2410_GPF0 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 0) #define S3C2410_GPF0_EINT0 (0x02 << 0) #define S3C2400_GPF0_RXD0 (0x02 << 0) -#define S3C2410_GPF1 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 1) #define S3C2410_GPF1_EINT1 (0x02 << 2) #define S3C2400_GPF1_RXD1 (0x02 << 2) #define S3C2400_GPF1_IICSDA (0x03 << 2) -#define S3C2410_GPF2 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 2) #define S3C2410_GPF2_EINT2 (0x02 << 4) #define S3C2400_GPF2_TXD0 (0x02 << 4) -#define S3C2410_GPF3 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 3) #define S3C2410_GPF3_EINT3 (0x02 << 6) #define S3C2400_GPF3_TXD1 (0x02 << 6) #define S3C2400_GPF3_IICSCL (0x03 << 6) -#define S3C2410_GPF4 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 4) #define S3C2410_GPF4_EINT4 (0x02 << 8) #define S3C2400_GPF4_nRTS0 (0x02 << 8) #define S3C2400_GPF4_nXBACK (0x03 << 8) -#define S3C2410_GPF5 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 5) #define S3C2410_GPF5_EINT5 (0x02 << 10) #define S3C2400_GPF5_nCTS0 (0x02 << 10) #define S3C2400_GPF5_nXBREQ (0x03 << 10) -#define S3C2410_GPF6 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 6) #define S3C2410_GPF6_EINT6 (0x02 << 12) #define S3C2400_GPF6_CLKOUT (0x02 << 12) -#define S3C2410_GPF7 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 7) #define S3C2410_GPF7_EINT7 (0x02 << 14) #define S3C2410_GPF_PUPDIS(x) (1<<(x)) @@ -621,85 +526,69 @@ #define S3C2400_GPGDAT S3C2410_GPIOREG(0x48) #define S3C2400_GPGUP S3C2410_GPIOREG(0x4C) -#define S3C2410_GPG0 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 0) #define S3C2410_GPG0_EINT8 (0x02 << 0) #define S3C2400_GPG0_I2SLRCK (0x02 << 0) -#define S3C2410_GPG1 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 1) #define S3C2410_GPG1_EINT9 (0x02 << 2) #define S3C2400_GPG1_I2SSCLK (0x02 << 2) -#define S3C2410_GPG2 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 2) #define S3C2410_GPG2_EINT10 (0x02 << 4) #define S3C2410_GPG2_nSS0 (0x03 << 4) #define S3C2400_GPG2_CDCLK (0x02 << 4) -#define S3C2410_GPG3 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 3) #define S3C2410_GPG3_EINT11 (0x02 << 6) #define S3C2410_GPG3_nSS1 (0x03 << 6) #define S3C2400_GPG3_I2SSDO (0x02 << 6) #define S3C2400_GPG3_I2SSDI (0x03 << 6) -#define S3C2410_GPG4 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 4) #define S3C2410_GPG4_EINT12 (0x02 << 8) #define S3C2400_GPG4_MMCCLK (0x02 << 8) #define S3C2400_GPG4_I2SSDI (0x03 << 8) #define S3C2410_GPG4_LCDPWREN (0x03 << 8) #define S3C2443_GPG4_LCDPWRDN (0x03 << 8) -#define S3C2410_GPG5 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 5) #define S3C2410_GPG5_EINT13 (0x02 << 10) #define S3C2400_GPG5_MMCCMD (0x02 << 10) #define S3C2400_GPG5_IICSDA (0x03 << 10) #define S3C2410_GPG5_SPIMISO1 (0x03 << 10) /* not s3c2443 */ -#define S3C2410_GPG6 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 6) #define S3C2410_GPG6_EINT14 (0x02 << 12) #define S3C2400_GPG6_MMCDAT (0x02 << 12) #define S3C2400_GPG6_IICSCL (0x03 << 12) #define S3C2410_GPG6_SPIMOSI1 (0x03 << 12) -#define S3C2410_GPG7 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 7) #define S3C2410_GPG7_EINT15 (0x02 << 14) #define S3C2410_GPG7_SPICLK1 (0x03 << 14) #define S3C2400_GPG7_SPIMISO (0x02 << 14) #define S3C2400_GPG7_IICSDA (0x03 << 14) -#define S3C2410_GPG8 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 8) #define S3C2410_GPG8_EINT16 (0x02 << 16) #define S3C2400_GPG8_SPIMOSI (0x02 << 16) #define S3C2400_GPG8_IICSCL (0x03 << 16) -#define S3C2410_GPG9 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 9) #define S3C2410_GPG9_EINT17 (0x02 << 18) #define S3C2400_GPG9_SPICLK (0x02 << 18) #define S3C2400_GPG9_MMCCLK (0x03 << 18) -#define S3C2410_GPG10 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 10) #define S3C2410_GPG10_EINT18 (0x02 << 20) -#define S3C2410_GPG11 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 11) #define S3C2410_GPG11_EINT19 (0x02 << 22) #define S3C2410_GPG11_TCLK1 (0x03 << 22) #define S3C2443_GPG11_CF_nIREQ (0x03 << 22) -#define S3C2410_GPG12 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 12) #define S3C2410_GPG12_EINT20 (0x02 << 24) #define S3C2410_GPG12_XMON (0x03 << 24) #define S3C2442_GPG12_nSPICS0 (0x03 << 24) #define S3C2443_GPG12_nINPACK (0x03 << 24) -#define S3C2410_GPG13 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 13) #define S3C2410_GPG13_EINT21 (0x02 << 26) #define S3C2410_GPG13_nXPON (0x03 << 26) #define S3C2443_GPG13_CF_nREG (0x03 << 26) -#define S3C2410_GPG14 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 14) #define S3C2410_GPG14_EINT22 (0x02 << 28) #define S3C2410_GPG14_YMON (0x03 << 28) #define S3C2443_GPG14_CF_RESET (0x03 << 28) -#define S3C2410_GPG15 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 15) #define S3C2410_GPG15_EINT23 (0x02 << 30) #define S3C2410_GPG15_nYPON (0x03 << 30) #define S3C2443_GPG15_CF_PWR (0x03 << 30) @@ -718,40 +607,29 @@ #define S3C2410_GPHDAT S3C2410_GPIOREG(0x74) #define S3C2410_GPHUP S3C2410_GPIOREG(0x78) -#define S3C2410_GPH0 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 0) #define S3C2410_GPH0_nCTS0 (0x02 << 0) -#define S3C2410_GPH1 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 1) #define S3C2410_GPH1_nRTS0 (0x02 << 2) -#define S3C2410_GPH2 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 2) #define S3C2410_GPH2_TXD0 (0x02 << 4) -#define S3C2410_GPH3 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 3) #define S3C2410_GPH3_RXD0 (0x02 << 6) -#define S3C2410_GPH4 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 4) #define S3C2410_GPH4_TXD1 (0x02 << 8) -#define S3C2410_GPH5 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 5) #define S3C2410_GPH5_RXD1 (0x02 << 10) -#define S3C2410_GPH6 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 6) #define S3C2410_GPH6_TXD2 (0x02 << 12) #define S3C2410_GPH6_nRTS1 (0x03 << 12) -#define S3C2410_GPH7 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 7) #define S3C2410_GPH7_RXD2 (0x02 << 14) #define S3C2410_GPH7_nCTS1 (0x03 << 14) -#define S3C2410_GPH8 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 8) #define S3C2410_GPH8_UCLK (0x02 << 16) -#define S3C2410_GPH9 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 9) #define S3C2410_GPH9_CLKOUT0 (0x02 << 18) #define S3C2442_GPH9_nSPICS0 (0x03 << 18) -#define S3C2410_GPH10 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 10) #define S3C2410_GPH10_CLKOUT1 (0x02 << 20) /* The S3C2412 and S3C2413 move the GPJ register set to after diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c index 43f7536c529..06a84adfb13 100644 --- a/arch/arm/mach-s3c2410/mach-amlm5900.c +++ b/arch/arm/mach-s3c2410/mach-amlm5900.c @@ -225,8 +225,8 @@ static void amlm5900_init_pm(void) } else { enable_irq_wake(IRQ_EINT9); /* configure the suspend/resume status pin */ - s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_pullup(S3C2410_GPF2, 0); + s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_pullup(S3C2410_GPF(2), 0); } } static void __init amlm5900_init(void) diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c index 3410caefb86..496463768de 100644 --- a/arch/arm/mach-s3c2410/mach-bast.c +++ b/arch/arm/mach-s3c2410/mach-bast.c @@ -213,15 +213,15 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = { static int bast_pm_suspend(struct sys_device *sd, pm_message_t state) { /* ensure that an nRESET is not generated on resume. */ - s3c2410_gpio_setpin(S3C2410_GPA21, 1); - s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPA(21), 1); + s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT); return 0; } static int bast_pm_resume(struct sys_device *sd) { - s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_nRSTOUT); + s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT); return 0; } diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index 7a7c4da4c25..d9cd5ddecf4 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -127,7 +127,7 @@ static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd) static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = { .udc_command = h1940_udc_pullup, - .vbus_pin = S3C2410_GPG5, + .vbus_pin = S3C2410_GPG(5), .vbus_pin_inverted = 1, }; diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c index 83705036ca6..0f6ed61af41 100644 --- a/arch/arm/mach-s3c2410/mach-n30.c +++ b/arch/arm/mach-s3c2410/mach-n30.c @@ -86,10 +86,10 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd) { switch (cmd) { case S3C2410_UDC_P_ENABLE : - s3c2410_gpio_setpin(S3C2410_GPB3, 1); + s3c2410_gpio_setpin(S3C2410_GPB(3), 1); break; case S3C2410_UDC_P_DISABLE : - s3c2410_gpio_setpin(S3C2410_GPB3, 0); + s3c2410_gpio_setpin(S3C2410_GPB(3), 0); break; case S3C2410_UDC_P_RESET : break; @@ -100,55 +100,55 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd) static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = { .udc_command = n30_udc_pullup, - .vbus_pin = S3C2410_GPG1, + .vbus_pin = S3C2410_GPG(1), .vbus_pin_inverted = 0, }; static struct gpio_keys_button n30_buttons[] = { { - .gpio = S3C2410_GPF0, + .gpio = S3C2410_GPF(0), .code = KEY_POWER, .desc = "Power", .active_low = 0, }, { - .gpio = S3C2410_GPG9, + .gpio = S3C2410_GPG(9), .code = KEY_UP, .desc = "Thumbwheel Up", .active_low = 0, }, { - .gpio = S3C2410_GPG8, + .gpio = S3C2410_GPG(8), .code = KEY_DOWN, .desc = "Thumbwheel Down", .active_low = 0, }, { - .gpio = S3C2410_GPG7, + .gpio = S3C2410_GPG(7), .code = KEY_ENTER, .desc = "Thumbwheel Press", .active_low = 0, }, { - .gpio = S3C2410_GPF7, + .gpio = S3C2410_GPF(7), .code = KEY_HOMEPAGE, .desc = "Home", .active_low = 0, }, { - .gpio = S3C2410_GPF6, + .gpio = S3C2410_GPF(6), .code = KEY_CALENDAR, .desc = "Calendar", .active_low = 0, }, { - .gpio = S3C2410_GPF5, + .gpio = S3C2410_GPF(5), .code = KEY_ADDRESSBOOK, .desc = "Contacts", .active_low = 0, }, { - .gpio = S3C2410_GPF4, + .gpio = S3C2410_GPF(4), .code = KEY_MAIL, .desc = "Mail", .active_low = 0, @@ -170,73 +170,73 @@ static struct platform_device n30_button_device = { static struct gpio_keys_button n35_buttons[] = { { - .gpio = S3C2410_GPF0, + .gpio = S3C2410_GPF(0), .code = KEY_POWER, .desc = "Power", .active_low = 0, }, { - .gpio = S3C2410_GPG9, + .gpio = S3C2410_GPG(9), .code = KEY_UP, .desc = "Joystick Up", .active_low = 0, }, { - .gpio = S3C2410_GPG8, + .gpio = S3C2410_GPG(8), .code = KEY_DOWN, .desc = "Joystick Down", .active_low = 0, }, { - .gpio = S3C2410_GPG6, + .gpio = S3C2410_GPG(6), .code = KEY_DOWN, .desc = "Joystick Left", .active_low = 0, }, { - .gpio = S3C2410_GPG5, + .gpio = S3C2410_GPG(5), .code = KEY_DOWN, .desc = "Joystick Right", .active_low = 0, }, { - .gpio = S3C2410_GPG7, + .gpio = S3C2410_GPG(7), .code = KEY_ENTER, .desc = "Joystick Press", .active_low = 0, }, { - .gpio = S3C2410_GPF7, + .gpio = S3C2410_GPF(7), .code = KEY_HOMEPAGE, .desc = "Home", .active_low = 0, }, { - .gpio = S3C2410_GPF6, + .gpio = S3C2410_GPF(6), .code = KEY_CALENDAR, .desc = "Calendar", .active_low = 0, }, { - .gpio = S3C2410_GPF5, + .gpio = S3C2410_GPF(5), .code = KEY_ADDRESSBOOK, .desc = "Contacts", .active_low = 0, }, { - .gpio = S3C2410_GPF4, + .gpio = S3C2410_GPF(4), .code = KEY_MAIL, .desc = "Mail", .active_low = 0, }, { - .gpio = S3C2410_GPF3, + .gpio = S3C2410_GPF(3), .code = SW_RADIO, .desc = "GPS Antenna", .active_low = 0, }, { - .gpio = S3C2410_GPG2, + .gpio = S3C2410_GPG(2), .code = SW_HEADPHONE_INSERT, .desc = "Headphone", .active_low = 0, @@ -260,7 +260,7 @@ static struct platform_device n35_button_device = { /* This is the bluetooth LED on the device. */ static struct s3c24xx_led_platdata n30_blue_led_pdata = { .name = "blue_led", - .gpio = S3C2410_GPG6, + .gpio = S3C2410_GPG(6), .def_trigger = "", }; @@ -271,7 +271,7 @@ static struct s3c24xx_led_platdata n30_blue_led_pdata = { static struct s3c24xx_led_platdata n30_warning_led_pdata = { .name = "warning_led", .flags = S3C24XX_LEDF_ACTLOW, - .gpio = S3C2410_GPD9, + .gpio = S3C2410_GPD(9), .def_trigger = "", }; diff --git a/arch/arm/mach-s3c2410/mach-qt2410.c b/arch/arm/mach-s3c2410/mach-qt2410.c index 7520aee3c9e..2cc9849eb44 100644 --- a/arch/arm/mach-s3c2410/mach-qt2410.c +++ b/arch/arm/mach-s3c2410/mach-qt2410.c @@ -199,7 +199,7 @@ static struct platform_device qt2410_cs89x0 = { /* LED */ static struct s3c24xx_led_platdata qt2410_pdata_led = { - .gpio = S3C2410_GPB0, + .gpio = S3C2410_GPB(0), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led", .def_trigger = "timer", @@ -219,18 +219,18 @@ static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs) { switch (cs) { case BITBANG_CS_ACTIVE: - s3c2410_gpio_setpin(S3C2410_GPB5, 0); + s3c2410_gpio_setpin(S3C2410_GPB(5), 0); break; case BITBANG_CS_INACTIVE: - s3c2410_gpio_setpin(S3C2410_GPB5, 1); + s3c2410_gpio_setpin(S3C2410_GPB(5), 1); break; } } static struct s3c2410_spigpio_info spi_gpio_cfg = { - .pin_clk = S3C2410_GPG7, - .pin_mosi = S3C2410_GPG6, - .pin_miso = S3C2410_GPG5, + .pin_clk = S3C2410_GPG(7), + .pin_mosi = S3C2410_GPG(6), + .pin_miso = S3C2410_GPG(5), .chip_select = &spi_gpio_cs, }; @@ -347,13 +347,13 @@ static void __init qt2410_machine_init(void) } s3c24xx_fb_set_platdata(&qt2410_fb_info); - s3c2410_gpio_cfgpin(S3C2410_GPB0, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB0, 1); + s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(0), 1); s3c24xx_udc_set_platdata(&qt2410_udc_cfg); s3c_i2c0_set_platdata(NULL); - s3c2410_gpio_cfgpin(S3C2410_GPB5, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPB(5), S3C2410_GPIO_OUTPUT); platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices)); s3c_pm_init(); diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c index 0507a7ec18c..1628cc773a2 100644 --- a/arch/arm/mach-s3c2410/mach-vr1000.c +++ b/arch/arm/mach-s3c2410/mach-vr1000.c @@ -278,19 +278,19 @@ static struct platform_device vr1000_dm9k1 = { static struct s3c24xx_led_platdata vr1000_led1_pdata = { .name = "led1", - .gpio = S3C2410_GPB0, + .gpio = S3C2410_GPB(0), .def_trigger = "", }; static struct s3c24xx_led_platdata vr1000_led2_pdata = { .name = "led2", - .gpio = S3C2410_GPB1, + .gpio = S3C2410_GPB(1), .def_trigger = "", }; static struct s3c24xx_led_platdata vr1000_led3_pdata = { .name = "led3", - .gpio = S3C2410_GPB2, + .gpio = S3C2410_GPB(2), .def_trigger = "", }; @@ -356,8 +356,8 @@ static struct clk *vr1000_clocks[] __initdata = { static void vr1000_power_off(void) { - s3c2410_gpio_cfgpin(S3C2410_GPB9, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB9, 1); + s3c2410_gpio_cfgpin(S3C2410_GPB(9), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(9), 1); } static void __init vr1000_map_io(void) diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c index 726cfc09388..143e08a599d 100644 --- a/arch/arm/mach-s3c2410/pm.c +++ b/arch/arm/mach-s3c2410/pm.c @@ -77,7 +77,7 @@ static void s3c2410_pm_prepare(void) } if ( machine_is_aml_m5900() ) - s3c2410_gpio_setpin(S3C2410_GPF2, 1); + s3c2410_gpio_setpin(S3C2410_GPF(2), 1); } @@ -92,7 +92,7 @@ static int s3c2410_pm_resume(struct sys_device *dev) __raw_writel(tmp, S3C2410_GSTATUS2); if ( machine_is_aml_m5900() ) - s3c2410_gpio_setpin(S3C2410_GPF2, 0); + s3c2410_gpio_setpin(S3C2410_GPF(2), 0); return 0; } diff --git a/arch/arm/mach-s3c2410/usb-simtec.c b/arch/arm/mach-s3c2410/usb-simtec.c index 506252b33fe..dd45eb4a6f0 100644 --- a/arch/arm/mach-s3c2410/usb-simtec.c +++ b/arch/arm/mach-s3c2410/usb-simtec.c @@ -54,9 +54,9 @@ usb_simtec_powercontrol(int port, int to) power_state[port] = to; if (power_state[0] && power_state[1]) - s3c2410_gpio_setpin(S3C2410_GPB4, 0); + s3c2410_gpio_setpin(S3C2410_GPB(4), 0); else - s3c2410_gpio_setpin(S3C2410_GPB4, 1); + s3c2410_gpio_setpin(S3C2410_GPB(4), 1); } static irqreturn_t @@ -64,7 +64,7 @@ usb_simtec_ocirq(int irq, void *pw) { struct s3c2410_hcd_info *info = pw; - if (s3c2410_gpio_getpin(S3C2410_GPG10) == 0) { + if (s3c2410_gpio_getpin(S3C2410_GPG(10)) == 0) { pr_debug("usb_simtec: over-current irq (oc detected)\n"); s3c2410_usb_report_oc(info, 3); } else { @@ -110,7 +110,7 @@ int usb_simtec_init(void) printk("USB Power Control, (c) 2004 Simtec Electronics\n"); s3c_device_usb.dev.platform_data = &usb_simtec_info; - s3c2410_gpio_cfgpin(S3C2410_GPB4, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB4, 1); + s3c2410_gpio_cfgpin(S3C2410_GPB(4), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(4), 1); return 0; } diff --git a/arch/arm/mach-s3c2412/mach-jive.c b/arch/arm/mach-s3c2412/mach-jive.c index 56d12b56c9d..8df506eac90 100644 --- a/arch/arm/mach-s3c2412/mach-jive.c +++ b/arch/arm/mach-s3c2412/mach-jive.c @@ -357,8 +357,8 @@ static void jive_lcm_reset(unsigned int set) { printk(KERN_DEBUG "%s(%d)\n", __func__, set); - s3c2410_gpio_setpin(S3C2410_GPG13, set); - s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPG(13), set); + s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT); } #undef LCD_UPPER_MARGIN @@ -391,13 +391,13 @@ static struct ili9320_platdata jive_lcm_config = { static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs) { - s3c2410_gpio_setpin(S3C2410_GPB7, cs ? 0 : 1); + s3c2410_gpio_setpin(S3C2410_GPB(7), cs ? 0 : 1); } static struct s3c2410_spigpio_info jive_lcd_spi = { .bus_num = 1, - .pin_clk = S3C2410_GPG8, - .pin_mosi = S3C2410_GPB8, + .pin_clk = S3C2410_GPG(8), + .pin_mosi = S3C2410_GPB(8), .num_chipselect = 1, .chip_select = jive_lcd_spi_chipselect, }; @@ -413,13 +413,13 @@ static struct platform_device jive_device_lcdspi = { static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs) { - s3c2410_gpio_setpin(S3C2410_GPH10, cs ? 0 : 1); + s3c2410_gpio_setpin(S3C2410_GPH(10), cs ? 0 : 1); } static struct s3c2410_spigpio_info jive_wm8750_spi = { .bus_num = 2, - .pin_clk = S3C2410_GPB4, - .pin_mosi = S3C2410_GPB9, + .pin_clk = S3C2410_GPB(4), + .pin_mosi = S3C2410_GPB(9), .num_chipselect = 1, .chip_select = jive_wm8750_chipselect, }; @@ -480,7 +480,7 @@ static struct platform_device *jive_devices[] __initdata = { }; static struct s3c2410_udc_mach_info jive_udc_cfg __initdata = { - .vbus_pin = S3C2410_GPG1, /* detect is on GPG1 */ + .vbus_pin = S3C2410_GPG(1), /* detect is on GPG1 */ }; /* Jive power management device */ @@ -530,8 +530,8 @@ static void jive_power_off(void) { printk(KERN_INFO "powering system down...\n"); - s3c2410_gpio_setpin(S3C2410_GPC5, 1); - s3c2410_gpio_cfgpin(S3C2410_GPC5, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPC(5), 1); + s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT); } static void __init jive_machine_init(void) @@ -635,22 +635,22 @@ static void __init jive_machine_init(void) /* initialise the spi */ - s3c2410_gpio_setpin(S3C2410_GPG13, 0); - s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPG(13), 0); + s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB7, 1); - s3c2410_gpio_cfgpin(S3C2410_GPB7, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(7), 1); + s3c2410_gpio_cfgpin(S3C2410_GPB(7), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB6, 0); - s3c2410_gpio_cfgpin(S3C2410_GPB6, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPB(6), 0); + s3c2410_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPG8, 1); - s3c2410_gpio_cfgpin(S3C2410_GPG8, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPG(8), 1); + s3c2410_gpio_cfgpin(S3C2410_GPG(8), S3C2410_GPIO_OUTPUT); /* initialise the WM8750 spi */ - s3c2410_gpio_setpin(S3C2410_GPH10, 1); - s3c2410_gpio_cfgpin(S3C2410_GPH10, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPH(10), 1); + s3c2410_gpio_cfgpin(S3C2410_GPH(10), S3C2410_GPIO_OUTPUT); /* Turn off suspend on both USB ports, and switch the * selectable USB port to USB device mode. */ diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c index 753aaedae55..9a5e4341972 100644 --- a/arch/arm/mach-s3c2412/mach-smdk2413.c +++ b/arch/arm/mach-s3c2412/mach-smdk2413.c @@ -85,10 +85,10 @@ static void smdk2413_udc_pullup(enum s3c2410_udc_cmd_e cmd) switch (cmd) { case S3C2410_UDC_P_ENABLE : - s3c2410_gpio_setpin(S3C2410_GPF2, 1); + s3c2410_gpio_setpin(S3C2410_GPF(2), 1); break; case S3C2410_UDC_P_DISABLE : - s3c2410_gpio_setpin(S3C2410_GPF2, 0); + s3c2410_gpio_setpin(S3C2410_GPF(2), 0); break; case S3C2410_UDC_P_RESET : break; @@ -135,8 +135,8 @@ static void __init smdk2413_machine_init(void) { /* Turn off suspend on both USB ports, and switch the * selectable USB port to USB device mode. */ - s3c2410_gpio_setpin(S3C2410_GPF2, 0); - s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPF(2), 0); + s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST | S3C2410_MISCCR_USBSUSPND0 | diff --git a/arch/arm/mach-s3c2440/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c index d363b6f9000..68f3870991b 100644 --- a/arch/arm/mach-s3c2440/mach-anubis.c +++ b/arch/arm/mach-s3c2440/mach-anubis.c @@ -469,7 +469,7 @@ static void __init anubis_map_io(void) anubis_nand_sets[0].nr_partitions = ARRAY_SIZE(anubis_default_nand_part_large); } else { /* ensure that the GPIO is setup */ - s3c2410_gpio_setpin(S3C2410_GPA0, 1); + s3c2410_gpio_setpin(S3C2410_GPA(0), 1); } } diff --git a/arch/arm/mach-s3c2440/mach-at2440evb.c b/arch/arm/mach-s3c2440/mach-at2440evb.c index 315c42e3127..dfc7010935d 100644 --- a/arch/arm/mach-s3c2440/mach-at2440evb.c +++ b/arch/arm/mach-s3c2440/mach-at2440evb.c @@ -166,7 +166,7 @@ static struct platform_device at2440evb_device_eth = { }; static struct s3c24xx_mci_pdata at2440evb_mci_pdata = { - .gpio_detect = S3C2410_GPG10, + .gpio_detect = S3C2410_GPG(10), }; /* 7" LCD panel */ diff --git a/arch/arm/mach-s3c2440/mach-nexcoder.c b/arch/arm/mach-s3c2440/mach-nexcoder.c index 4b2088cb05e..d43edede590 100644 --- a/arch/arm/mach-s3c2440/mach-nexcoder.c +++ b/arch/arm/mach-s3c2440/mach-nexcoder.c @@ -121,16 +121,16 @@ static struct platform_device *nexcoder_devices[] __initdata = { static void __init nexcoder_sensorboard_init(void) { // Initialize SCCB bus - s3c2410_gpio_setpin(S3C2410_GPE14, 1); // IICSCL - s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPE15, 1); // IICSDA - s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPE(14), 1); // IICSCL + s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPE(15), 1); // IICSDA + s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT); // Power up the sensor board - s3c2410_gpio_setpin(S3C2410_GPF1, 1); - s3c2410_gpio_cfgpin(S3C2410_GPF1, S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN - s3c2410_gpio_setpin(S3C2410_GPF2, 0); - s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN + s3c2410_gpio_setpin(S3C2410_GPF(1), 1); + s3c2410_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN + s3c2410_gpio_setpin(S3C2410_GPF(2), 0); + s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN } static void __init nexcoder_map_io(void) diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c index ad0fdc4a794..cba064b49a6 100644 --- a/arch/arm/mach-s3c2440/mach-osiris.c +++ b/arch/arm/mach-s3c2440/mach-osiris.c @@ -292,8 +292,8 @@ static int osiris_pm_suspend(struct sys_device *sd, pm_message_t state) __raw_writeb(tmp, OSIRIS_VA_CTRL0); /* ensure that an nRESET is not generated on resume. */ - s3c2410_gpio_setpin(S3C2410_GPA21, 1); - s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_setpin(S3C2410_GPA(21), 1); + s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT); return 0; } @@ -305,7 +305,7 @@ static int osiris_pm_resume(struct sys_device *sd) __raw_writeb(pm_osiris_ctrl0, OSIRIS_VA_CTRL0); - s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_nRSTOUT); + s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT); return 0; } @@ -385,7 +385,7 @@ static void __init osiris_map_io(void) osiris_nand_sets[0].nr_partitions = ARRAY_SIZE(osiris_default_nand_part_large); } else { /* write-protect line to the NAND */ - s3c2410_gpio_setpin(S3C2410_GPA0, 1); + s3c2410_gpio_setpin(S3C2410_GPA(0), 1); } /* fix bus configuration (nBE settings wrong on ABLE pre v2.20) */ diff --git a/arch/arm/plat-s3c24xx/common-smdk.c b/arch/arm/plat-s3c24xx/common-smdk.c index fe658c48f72..aa119863c5c 100644 --- a/arch/arm/plat-s3c24xx/common-smdk.c +++ b/arch/arm/plat-s3c24xx/common-smdk.c @@ -48,27 +48,27 @@ /* LED devices */ static struct s3c24xx_led_platdata smdk_pdata_led4 = { - .gpio = S3C2410_GPF4, + .gpio = S3C2410_GPF(4), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led4", .def_trigger = "timer", }; static struct s3c24xx_led_platdata smdk_pdata_led5 = { - .gpio = S3C2410_GPF5, + .gpio = S3C2410_GPF(5), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led5", .def_trigger = "nand-disk", }; static struct s3c24xx_led_platdata smdk_pdata_led6 = { - .gpio = S3C2410_GPF6, + .gpio = S3C2410_GPF(6), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led6", }; static struct s3c24xx_led_platdata smdk_pdata_led7 = { - .gpio = S3C2410_GPF7, + .gpio = S3C2410_GPF(7), .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, .name = "led7", }; @@ -185,15 +185,15 @@ void __init smdk_machine_init(void) { /* Configure the LEDs (even if we have no LED support)*/ - s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPIO_OUTPUT); - s3c2410_gpio_cfgpin(S3C2410_GPF7, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPF(4), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPF(5), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPF(6), S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(S3C2410_GPF(7), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPF4, 1); - s3c2410_gpio_setpin(S3C2410_GPF5, 1); - s3c2410_gpio_setpin(S3C2410_GPF6, 1); - s3c2410_gpio_setpin(S3C2410_GPF7, 1); + s3c2410_gpio_setpin(S3C2410_GPF(4), 1); + s3c2410_gpio_setpin(S3C2410_GPF(5), 1); + s3c2410_gpio_setpin(S3C2410_GPF(6), 1); + s3c2410_gpio_setpin(S3C2410_GPF(7), 1); if (machine_is_smdk2443()) smdk_nand_info.twrph0 = 50; diff --git a/arch/arm/plat-s3c24xx/gpio.c b/arch/arm/plat-s3c24xx/gpio.c index 65ebbaff7d5..ae0b9d6f3fb 100644 --- a/arch/arm/plat-s3c24xx/gpio.c +++ b/arch/arm/plat-s3c24xx/gpio.c @@ -183,19 +183,19 @@ EXPORT_SYMBOL(s3c2410_modify_misccr); int s3c2410_gpio_getirq(unsigned int pin) { - if (pin < S3C2410_GPF0 || pin > S3C2410_GPG15) + if (pin < S3C2410_GPF(0) || pin > S3C2410_GPG(15)) return -1; /* not valid interrupts */ - if (pin < S3C2410_GPG0 && pin > S3C2410_GPF7) + if (pin < S3C2410_GPG(0) && pin > S3C2410_GPF(7)) return -1; /* not valid pin */ - if (pin < S3C2410_GPF4) - return (pin - S3C2410_GPF0) + IRQ_EINT0; + if (pin < S3C2410_GPF(4)) + return (pin - S3C2410_GPF(0)) + IRQ_EINT0; - if (pin < S3C2410_GPG0) - return (pin - S3C2410_GPF4) + IRQ_EINT4; + if (pin < S3C2410_GPG(0)) + return (pin - S3C2410_GPF(4)) + IRQ_EINT4; - return (pin - S3C2410_GPG0) + IRQ_EINT8; + return (pin - S3C2410_GPG(0)) + IRQ_EINT8; } EXPORT_SYMBOL(s3c2410_gpio_getirq); diff --git a/arch/arm/plat-s3c24xx/gpiolib.c b/arch/arm/plat-s3c24xx/gpiolib.c index 60a9f724720..a82adc3c98a 100644 --- a/arch/arm/plat-s3c24xx/gpiolib.c +++ b/arch/arm/plat-s3c24xx/gpiolib.c @@ -82,7 +82,7 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { .base = S3C2410_GPACON, .pm = __gpio_pm(&s3c_gpio_pm_1bit), .chip = { - .base = S3C2410_GPA0, + .base = S3C2410_GPA(0), .owner = THIS_MODULE, .label = "GPIOA", .ngpio = 24, @@ -94,7 +94,7 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { .base = S3C2410_GPBCON, .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPB0, + .base = S3C2410_GPB(0), .owner = THIS_MODULE, .label = "GPIOB", .ngpio = 16, @@ -104,7 +104,7 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { .base = S3C2410_GPCCON, .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPC0, + .base = S3C2410_GPC(0), .owner = THIS_MODULE, .label = "GPIOC", .ngpio = 16, @@ -114,7 +114,7 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { .base = S3C2410_GPDCON, .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPD0, + .base = S3C2410_GPD(0), .owner = THIS_MODULE, .label = "GPIOD", .ngpio = 16, @@ -124,7 +124,7 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { .base = S3C2410_GPECON, .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPE0, + .base = S3C2410_GPE(0), .label = "GPIOE", .owner = THIS_MODULE, .ngpio = 16, @@ -134,7 +134,7 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { .base = S3C2410_GPFCON, .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPF0, + .base = S3C2410_GPF(0), .owner = THIS_MODULE, .label = "GPIOF", .ngpio = 8, @@ -145,7 +145,7 @@ struct s3c_gpio_chip s3c24xx_gpios[] = { .base = S3C2410_GPGCON, .pm = __gpio_pm(&s3c_gpio_pm_2bit), .chip = { - .base = S3C2410_GPG0, + .base = S3C2410_GPG(0), .owner = THIS_MODULE, .label = "GPIOG", .ngpio = 10, diff --git a/arch/arm/plat-s3c24xx/pm.c b/arch/arm/plat-s3c24xx/pm.c index 16aaf36b6e5..56e5253ca02 100644 --- a/arch/arm/plat-s3c24xx/pm.c +++ b/arch/arm/plat-s3c24xx/pm.c @@ -124,12 +124,12 @@ void s3c_pm_configure_extint(void) * and then configure it as an input if it is not */ - for (pin = S3C2410_GPF0; pin <= S3C2410_GPF7; pin++) { - s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF0); + for (pin = S3C2410_GPF(0); pin <= S3C2410_GPF(7); pin++) { + s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF(0)); } - for (pin = S3C2410_GPG0; pin <= S3C2410_GPG7; pin++) { - s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG0)+8); + for (pin = S3C2410_GPG(0); pin <= S3C2410_GPG(7); pin++) { + s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG(0))+8); } } diff --git a/arch/arm/plat-s3c24xx/setup-i2c.c b/arch/arm/plat-s3c24xx/setup-i2c.c index e0d18530555..71a6accf114 100644 --- a/arch/arm/plat-s3c24xx/setup-i2c.c +++ b/arch/arm/plat-s3c24xx/setup-i2c.c @@ -21,6 +21,6 @@ struct platform_device; void s3c_i2c0_cfg_gpio(struct platform_device *dev) { - s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_IICSDA); - s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_IICSCL); + s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPE15_IICSDA); + s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPE14_IICSCL); } diff --git a/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c b/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c index 8b403cbb53d..9edf7894eed 100644 --- a/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c +++ b/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c @@ -22,16 +22,16 @@ void s3c24xx_spi_gpiocfg_bus0_gpe11_12_13(struct s3c2410_spi_info *spi, int enable) { if (enable) { - s3c2410_gpio_cfgpin(S3C2410_GPE13, S3C2410_GPE13_SPICLK0); - s3c2410_gpio_cfgpin(S3C2410_GPE12, S3C2410_GPE12_SPIMOSI0); - s3c2410_gpio_cfgpin(S3C2410_GPE11, S3C2410_GPE11_SPIMISO0); - s3c2410_gpio_pullup(S3C2410_GPE11, 0); - s3c2410_gpio_pullup(S3C2410_GPE13, 0); + s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPE13_SPICLK0); + s3c2410_gpio_cfgpin(S3C2410_GPE(12), S3C2410_GPE12_SPIMOSI0); + s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPE11_SPIMISO0); + s3c2410_gpio_pullup(S3C2410_GPE(11), 0); + s3c2410_gpio_pullup(S3C2410_GPE(13), 0); } else { - s3c2410_gpio_cfgpin(S3C2410_GPE13, S3C2410_GPIO_INPUT); - s3c2410_gpio_cfgpin(S3C2410_GPE11, S3C2410_GPIO_INPUT); - s3c2410_gpio_pullup(S3C2410_GPE11, 1); - s3c2410_gpio_pullup(S3C2410_GPE12, 1); - s3c2410_gpio_pullup(S3C2410_GPE13, 1); + s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT); + s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT); + s3c2410_gpio_pullup(S3C2410_GPE(11), 1); + s3c2410_gpio_pullup(S3C2410_GPE(12), 1); + s3c2410_gpio_pullup(S3C2410_GPE(13), 1); } } diff --git a/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c b/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c index 8fccd4e549f..f34d0fc69ad 100644 --- a/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c +++ b/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c @@ -22,16 +22,16 @@ void s3c24xx_spi_gpiocfg_bus1_gpg5_6_7(struct s3c2410_spi_info *spi, int enable) { if (enable) { - s3c2410_gpio_cfgpin(S3C2410_GPG7, S3C2410_GPG7_SPICLK1); - s3c2410_gpio_cfgpin(S3C2410_GPG6, S3C2410_GPG6_SPIMOSI1); - s3c2410_gpio_cfgpin(S3C2410_GPG5, S3C2410_GPG5_SPIMISO1); - s3c2410_gpio_pullup(S3C2410_GPG5, 0); - s3c2410_gpio_pullup(S3C2410_GPG6, 0); + s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPG7_SPICLK1); + s3c2410_gpio_cfgpin(S3C2410_GPG(6), S3C2410_GPG6_SPIMOSI1); + s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPG5_SPIMISO1); + s3c2410_gpio_pullup(S3C2410_GPG(5), 0); + s3c2410_gpio_pullup(S3C2410_GPG(6), 0); } else { - s3c2410_gpio_cfgpin(S3C2410_GPG7, S3C2410_GPIO_INPUT); - s3c2410_gpio_cfgpin(S3C2410_GPG5, S3C2410_GPIO_INPUT); - s3c2410_gpio_pullup(S3C2410_GPG5, 1); - s3c2410_gpio_pullup(S3C2410_GPG6, 1); - s3c2410_gpio_pullup(S3C2410_GPG7, 1); + s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT); + s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT); + s3c2410_gpio_pullup(S3C2410_GPG(5), 1); + s3c2410_gpio_pullup(S3C2410_GPG(6), 1); + s3c2410_gpio_pullup(S3C2410_GPG(7), 1); } } |