Blackfin arch: add new processor ADSP-BF52x arch/mach support

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

9 files changed, 1886 insertions, 0 deletions

diff --git a/arch/blackfin/mach-bf527/Kconfig b/arch/blackfin/mach-bf527/Kconfig
new file mode 100644
index 00000000000..50321f723de
--- /dev/null
+++ b/arch/blackfin/mach-bf527/Kconfig
@@ -0,0 +1,251 @@
+if (BF52x)
+
+menu "BF527 Specific Configuration"
+
+comment "Alternative Multiplexing Scheme"
+
+choice
+	prompt "SPORT0"
+	default BF527_SPORT0_PORTG
+	help
+	  Select PORT used for SPORT0. See Hardware Reference Manual
+
+config BF527_SPORT0_PORTF
+	bool "PORT F"
+	help
+	  PORT F
+
+config BF527_SPORT0_PORTG
+	bool "PORT G"
+	help
+	  PORT G
+endchoice
+
+choice
+	prompt "SPORT0 TSCLK Location"
+	depends on BF527_SPORT0_PORTG
+	default BF527_SPORT0_TSCLK_PG10
+	help
+	  Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual
+
+config BF527_SPORT0_TSCLK_PG10
+	bool "PORT PG10"
+	help
+	  PORT PG10
+
+config BF527_SPORT0_TSCLK_PG14
+	bool "PORT PG14"
+	help
+	  PORT PG14
+endchoice
+
+choice
+	prompt "UART1"
+	default BF527_UART1_PORTG
+	help
+	  Select PORT used for UART1. See Hardware Reference Manual
+
+config BF527_UART1_PORTF
+	bool "PORT F"
+	help
+	  PORT F
+
+config BF527_UART1_PORTG
+	bool "PORT G"
+	help
+	  PORT G
+endchoice
+
+choice
+	prompt "NAND (NFC) Data"
+	default BF527_NAND_D_PORTH
+	help
+	  Select PORT used for NAND Data Bus. See Hardware Reference Manual
+
+config BF527_NAND_D_PORTF
+	bool "PORT F"
+	help
+	  PORT F
+
+config BF527_NAND_D_PORTH
+	bool "PORT H"
+	help
+	  PORT H
+endchoice
+
+comment "Interrupt Priority Assignment"
+menu "Priority"
+
+config IRQ_PLL_WAKEUP
+	int "IRQ_PLL_WAKEUP"
+	default 7
+config IRQ_DMA0_ERROR
+	int "IRQ_DMA0_ERROR"
+	default 7
+config IRQ_DMAR0_BLK
+	int "IRQ_DMAR0_BLK"
+	default 7
+config IRQ_DMAR1_BLK
+	int "IRQ_DMAR1_BLK"
+	default 7
+config IRQ_DMAR0_OVR
+	int "IRQ_DMAR0_OVR"
+	default 7
+config IRQ_DMAR1_OVR
+	int "IRQ_DMAR1_OVR"
+	default 7
+config IRQ_PPI_ERROR
+	int "IRQ_PPI_ERROR"
+	default 7
+config IRQ_MAC_ERROR
+	int "IRQ_MAC_ERROR"
+	default 7
+config IRQ_SPORT0_ERROR
+	int "IRQ_SPORT0_ERROR"
+	default 7
+config IRQ_SPORT1_ERROR
+	int "IRQ_SPORT1_ERROR"
+	default 7
+config IRQ_UART0_ERROR
+	int "IRQ_UART0_ERROR"
+	default 7
+config IRQ_UART1_ERROR
+	int "IRQ_UART1_ERROR"
+	default 7
+config IRQ_RTC
+	int "IRQ_RTC"
+	default 8
+config IRQ_PPI
+	int "IRQ_PPI"
+	default 8
+config IRQ_SPORT0_RX
+	int "IRQ_SPORT0_RX"
+	default 9
+config IRQ_SPORT0_TX
+	int "IRQ_SPORT0_TX"
+	default 9
+config IRQ_SPORT1_RX
+	int "IRQ_SPORT1_RX"
+	default 9
+config IRQ_SPORT1_TX
+	int "IRQ_SPORT1_TX"
+	default 9
+config IRQ_TWI
+	int "IRQ_TWI"
+	default 10
+config IRQ_SPI
+	int "IRQ_SPI"
+	default 10
+config IRQ_UART0_RX
+	int "IRQ_UART0_RX"
+	default 10
+config IRQ_UART0_TX
+	int "IRQ_UART0_TX"
+	default 10
+config IRQ_UART1_RX
+	int "IRQ_UART1_RX"
+	default 10
+config IRQ_UART1_TX
+	int "IRQ_UART1_TX"
+	default 10
+config IRQ_OPTSEC
+	int "IRQ_OPTSEC"
+	default 11
+config IRQ_CNT
+	int "IRQ_CNT"
+	default 11
+config IRQ_MAC_RX
+	int "IRQ_MAC_RX"
+	default 11
+config IRQ_PORTH_INTA
+	int "IRQ_PORTH_INTA"
+	default 11
+config IRQ_MAC_TX
+	int "IRQ_MAC_TX/NFC"
+	default 11
+config IRQ_PORTH_INTB
+	int "IRQ_PORTH_INTB"
+	default 11
+config IRQ_TMR0
+	int "IRQ_TMR0"
+	default 12
+config IRQ_TMR1
+	int "IRQ_TMR1"
+	default 12
+config IRQ_TMR2
+	int "IRQ_TMR2"
+	default 12
+config IRQ_TMR3
+	int "IRQ_TMR3"
+	default 12
+config IRQ_TMR4
+	int "IRQ_TMR4"
+	default 12
+config IRQ_TMR5
+	int "IRQ_TMR5"
+	default 12
+config IRQ_TMR6
+	int "IRQ_TMR6"
+	default 12
+config IRQ_TMR7
+	int "IRQ_TMR7"
+	default 12
+config IRQ_PORTG_INTA
+	int "IRQ_PORTG_INTA"
+	default 12
+config IRQ_PORTG_INTB
+	int "IRQ_PORTG_INTB"
+	default 12
+config IRQ_MEM_DMA0
+	int "IRQ_MEM_DMA0"
+	default 13
+config IRQ_MEM_DMA1
+	int "IRQ_MEM_DMA1"
+	default 13
+config IRQ_WATCH
+	int "IRQ_WATCH"
+	default 13
+config IRQ_PORTF_INTA
+	int "IRQ_PORTF_INTA"
+	default 13
+config IRQ_PORTF_INTB
+	int "IRQ_PORTF_INTB"
+	default 13
+config IRQ_SPI_ERROR
+	int "IRQ_SPI_ERROR"
+	default 7
+config IRQ_NFC_ERROR
+	int "IRQ_NFC_ERROR"
+	default 7
+config IRQ_HDMA_ERROR
+	int "IRQ_HDMA_ERROR"
+	default 7
+config IRQ_HDMA
+	int "IRQ_HDMA"
+	default 7
+config IRQ_USB_EINT
+	int "IRQ_USB_EINT"
+	default 10
+config IRQ_USB_INT0
+	int "IRQ_USB_INT0"
+	default 10
+config IRQ_USB_INT1
+	int "IRQ_USB_INT1"
+	default 10
+config IRQ_USB_INT2
+	int "IRQ_USB_INT2"
+	default 10
+config IRQ_USB_DMA
+	int "IRQ_USB_DMA"
+	default 10
+
+	help
+	  Enter the priority numbers between 7-13 ONLY.  Others are Reserved.
+	  This applies to all the above.  It is not recommended to assign the
+	  highest priority number 7 to UART or any other device.
+
+endmenu
+
+endmenu
+
+endif
diff --git a/arch/blackfin/mach-bf527/Makefile b/arch/blackfin/mach-bf527/Makefile
new file mode 100644
index 00000000000..9f99f5d0bcd
--- /dev/null
+++ b/arch/blackfin/mach-bf527/Makefile
@@ -0,0 +1,9 @@
+#
+# arch/blackfin/mach-bf527/Makefile
+#
+
+extra-y := head.o
+
+obj-y := ints-priority.o dma.o
+
+obj-$(CONFIG_CPU_FREQ)   += cpu.o
diff --git a/arch/blackfin/mach-bf527/boards/Makefile b/arch/blackfin/mach-bf527/boards/Makefile
new file mode 100644
index 00000000000..912ac8ebc88
--- /dev/null
+++ b/arch/blackfin/mach-bf527/boards/Makefile
@@ -0,0 +1,7 @@
+#
+# arch/blackfin/mach-bf532/boards/Makefile
+#
+
+obj-y					+= eth_mac.o
+obj-$(CONFIG_BFIN527_EZKIT)		+= ezkit.o
+
diff --git a/arch/blackfin/mach-bf527/boards/eth_mac.c b/arch/blackfin/mach-bf527/boards/eth_mac.c
new file mode 100644
index 00000000000..a725cc8a929
--- /dev/null
+++ b/arch/blackfin/mach-bf527/boards/eth_mac.c
@@ -0,0 +1,50 @@
+/*
+ *  arch/blackfin/mach-bf537/board/eth_mac.c
+ *
+ *  Copyright (C) 2007 Analog Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#include <linux/module.h>
+#include <asm/blackfin.h>
+
+#if	defined(CONFIG_GENERIC_BOARD) || defined(CONFIG_BFIN537_STAMP)
+
+/*
+ * Currently the MAC address is saved in Flash by U-Boot
+ */
+#define FLASH_MAC	0x203f0000
+
+void get_bf537_ether_addr(char *addr)
+{
+	unsigned int flash_mac = (unsigned int) FLASH_MAC;
+	*(u32 *)(&(addr[0])) = bfin_read32(flash_mac);
+	flash_mac += 4;
+	*(u16 *)(&(addr[4])) = bfin_read16(flash_mac);
+}
+
+#else
+
+/*
+ * Provide MAC address function for other specific board setting
+ */
+void get_bf537_ether_addr(char *addr)
+{
+	printk(KERN_WARNING "%s: No valid Ethernet MAC address found\n", __FILE__);
+}
+
+#endif
+
+EXPORT_SYMBOL(get_bf537_ether_addr);
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
new file mode 100644
index 00000000000..09fb624af5a
--- /dev/null
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -0,0 +1,737 @@
+/*
+ * File:         arch/blackfin/mach-bf527/boards/ezkit.c
+ * Based on:     arch/blackfin/mach-bf537/boards/stamp.c
+ * Author:       Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created:
+ * Description:
+ *
+ * Modified:
+ *               Copyright 2005 National ICT Australia (NICTA)
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb_isp1362.h>
+#endif
+#include <linux/pata_platform.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb_sl811.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <linux/spi/ad7877.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+char *bfin_board_name = "ADDS-BF527-EZKIT";
+
+/*
+ *  Driver needs to know address, irq and flag pin.
+ */
+
+#define ISP1761_BASE       0x203C0000
+#define ISP1761_IRQ        IRQ_PF7
+
+#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+static struct resource bfin_isp1761_resources[] = {
+	[0] = {
+		.name	= "isp1761-regs",
+		.start  = ISP1761_BASE + 0x00000000,
+		.end    = ISP1761_BASE + 0x000fffff,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = ISP1761_IRQ,
+		.end    = ISP1761_IRQ,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_isp1761_device = {
+	.name           = "isp1761",
+	.id             = 0,
+	.num_resources  = ARRAY_SIZE(bfin_isp1761_resources),
+	.resource       = bfin_isp1761_resources,
+};
+
+static struct platform_device *bfin_isp1761_devices[] = {
+	&bfin_isp1761_device,
+};
+
+int __init bfin_isp1761_init(void)
+{
+	unsigned int num_devices = ARRAY_SIZE(bfin_isp1761_devices);
+
+	printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+	set_irq_type(ISP1761_IRQ, IRQF_TRIGGER_FALLING);
+
+	return platform_add_devices(bfin_isp1761_devices, num_devices);
+}
+
+void __exit bfin_isp1761_exit(void)
+{
+	platform_device_unregister(&bfin_isp1761_device);
+}
+
+arch_initcall(bfin_isp1761_init);
+#endif
+
+#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+static struct resource bfin_pcmcia_cf_resources[] = {
+	{
+		.start = 0x20310000, /* IO PORT */
+		.end = 0x20312000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20311000, /* Attribute Memory */
+		.end = 0x20311FFF,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF4,
+		.end = IRQ_PF4,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+	}, {
+		.start = 6, /* Card Detect PF6 */
+		.end = 6,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pcmcia_cf_device = {
+	.name = "bfin_cf_pcmcia",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
+	.resource = bfin_pcmcia_cf_resources,
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+static struct resource smc91x_resources[] = {
+	{
+		.name = "smc91x-regs",
+		.start = 0x20300300,
+		.end = 0x20300300 + 16,
+		.flags = IORESOURCE_MEM,
+	}, {
+
+		.start = IRQ_PF7,
+		.end = IRQ_PF7,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+static struct platform_device smc91x_device = {
+	.name = "smc91x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smc91x_resources),
+	.resource = smc91x_resources,
+};
+#endif
+
+#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+static struct resource dm9000_resources[] = {
+	[0] = {
+		.start	= 0x203FB800,
+		.end	= 0x203FB800 + 8,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_PF9,
+		.end	= IRQ_PF9,
+		.flags	= (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
+	},
+};
+
+static struct platform_device dm9000_device = {
+	.name		= "dm9000",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(dm9000_resources),
+	.resource	= dm9000_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
+static struct resource sl811_hcd_resources[] = {
+	{
+		.start = 0x20340000,
+		.end = 0x20340000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20340004,
+		.end = 0x20340004,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = CONFIG_USB_SL811_BFIN_IRQ,
+		.end = CONFIG_USB_SL811_BFIN_IRQ,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
+void sl811_port_power(struct device *dev, int is_on)
+{
+	gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
+	gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS);
+
+	if (is_on)
+		gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 1);
+	else
+		gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 0);
+}
+#endif
+
+static struct sl811_platform_data sl811_priv = {
+	.potpg = 10,
+	.power = 250,       /* == 500mA */
+#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
+	.port_power = &sl811_port_power,
+#endif
+};
+
+static struct platform_device sl811_hcd_device = {
+	.name = "sl811-hcd",
+	.id = 0,
+	.dev = {
+		.platform_data = &sl811_priv,
+	},
+	.num_resources = ARRAY_SIZE(sl811_hcd_resources),
+	.resource = sl811_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+	{
+		.start = 0x20360000,
+		.end = 0x20360000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20360004,
+		.end = 0x20360004,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
+		.end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+	.sel15Kres = 1,
+	.clknotstop = 0,
+	.oc_enable = 0,
+	.int_act_high = 0,
+	.int_edge_triggered = 0,
+	.remote_wakeup_connected = 0,
+	.no_power_switching = 1,
+	.power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+	.name = "isp1362-hcd",
+	.id = 0,
+	.dev = {
+		.platform_data = &isp1362_priv,
+	},
+	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+	.resource = isp1362_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mac_device = {
+	.name = "bfin_mac",
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+	{
+		.start = 0x20300000,
+		.end = 0x20300000 + 0x100,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF7,
+		.end = IRQ_PF7,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device net2272_bfin_device = {
+	.name = "net2272",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
+	.resource = net2272_bfin_resources,
+};
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader",
+		.size = 0x00020000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "kernel",
+		.size = 0xe0000,
+		.offset = 0x20000
+	}, {
+		.name = "file system",
+		.size = 0x700000,
+		.offset = 0x00100000,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) \
+	|| defined(CONFIG_SPI_ADC_BF533_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+	.enable_dma = 1,         /* use dma transfer with this chip*/
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) \
+	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
+static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+	.enable_dma = 1,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_PBX)
+static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
+	.ctl_reg	= 0x4, /* send zero */
+	.enable_dma	= 0,
+	.bits_per_word	= 8,
+	.cs_change_per_word = 1,
+};
+#endif
+
+#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+static struct bfin5xx_spi_chip ad5304_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+
+static const struct ad7877_platform_data bfin_ad7877_ts_info = {
+	.model			= 7877,
+	.vref_delay_usecs	= 50,	/* internal, no capacitor */
+	.x_plate_ohms		= 419,
+	.y_plate_ohms		= 486,
+	.pressure_max		= 1000,
+	.pressure_min		= 0,
+	.stopacq_polarity 	= 1,
+	.first_conversion_delay = 3,
+	.acquisition_time 	= 1,
+	.averaging 		= 1,
+	.pen_down_acc_interval 	= 1,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) \
+	|| defined(CONFIG_SPI_ADC_BF533_MODULE)
+	{
+		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_adc_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) \
+	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+	{
+		.modalias = "ad1836-spi",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.controller_data = &ad1836_spi_chip_info,
+	},
+#endif
+#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
+	{
+		.modalias = "ad9960-spi",
+		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &ad9960_spi_chip_info,
+	},
+#endif
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+	{
+		.modalias = "spi_mmc_dummy",
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 0,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+		.mode = SPI_MODE_3,
+	},
+	{
+		.modalias = "spi_mmc",
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SPI_MMC_CS_CHAN,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_PBX)
+	{
+		.modalias = "fxs-spi",
+		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 8 - CONFIG_J11_JUMPER,
+		.controller_data = &spi_si3xxx_chip_info,
+		.mode = SPI_MODE_3,
+	},
+	{
+		.modalias = "fxo-spi",
+		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 8 - CONFIG_J19_JUMPER,
+		.controller_data = &spi_si3xxx_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+	{
+		.modalias = "ad5304_spi",
+		.max_speed_hz = 1250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 2,
+		.platform_data = NULL,
+		.controller_data = &ad5304_chip_info,
+		.mode = SPI_MODE_2,
+	},
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+	{
+		.modalias		= "ad7877",
+		.platform_data		= &bfin_ad7877_ts_info,
+		.irq			= IRQ_PF6,
+		.max_speed_hz	= 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num	= 1,
+		.chip_select  = 1,
+		.controller_data = &spi_ad7877_chip_info,
+	},
+#endif
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+		},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+static struct platform_device bfin_fb_device = {
+	.name = "bf537-lq035",
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+static struct platform_device bfin_fb_adv7393_device = {
+	.name = "bfin-adv7393",
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+};
+
+static struct platform_device bfin_uart_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart_resources),
+	.resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+	[0] = {
+		.start = TWI0_REGBASE,
+		.end   = TWI0_REGBASE,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_TWI,
+		.end   = IRQ_TWI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+	.name = "i2c-bfin-twi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
+	.resource = bfin_twi0_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+};
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT	55
+
+static struct pata_platform_info bfin_pata_platform_data = {
+	.ioport_shift = 1,
+	.irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+	{
+		.start = 0x20314020,
+		.end = 0x2031403F,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = 0x2031401C,
+		.end = 0x2031401F,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = PATA_INT,
+		.end = PATA_INT,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pata_device = {
+	.name = "pata_platform",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(bfin_pata_resources),
+	.resource = bfin_pata_resources,
+	.dev = {
+		.platform_data = &bfin_pata_platform_data,
+	}
+};
+#endif
+
+static struct platform_device *stamp_devices[] __initdata = {
+#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+	&bfin_pcmcia_cf_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
+	&sl811_hcd_device,
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+	&isp1362_hcd_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	&smc91x_device,
+#endif
+
+#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+	&dm9000_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+	&bfin_mac_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	&net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+	&bfin_fb_device,
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+	&bfin_fb_adv7393_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+	&bfin_uart_device,
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+	&i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+	&bfin_sport0_uart_device,
+	&bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	&bfin_pata_device,
+#endif
+};
+
+static int __init stamp_init(void)
+{
+	printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+	platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	spi_register_board_info(bfin_spi_board_info,
+				ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
+	return 0;
+}
+
+arch_initcall(stamp_init);
+
+void native_machine_restart(char *cmd)
+{
+	/* workaround reboot hang when booting from SPI */
+	if ((bfin_read_SYSCR() & 0x7) == 0x3)
+		bfin_gpio_reset_spi0_ssel1();
+}
diff --git a/arch/blackfin/mach-bf527/cpu.c b/arch/blackfin/mach-bf527/cpu.c
new file mode 100644
index 00000000000..1975402b1db
--- /dev/null
+++ b/arch/blackfin/mach-bf527/cpu.c
@@ -0,0 +1,161 @@
+/*
+ * File:         arch/blackfin/mach-bf527/cpu.c
+ * Based on:	arch/blackfin/mach-bf537/cpu.c
+ * Author:       michael.kang@analog.com
+ *
+ * Created:
+ * Description:  clock scaling for the bf527
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/cpufreq.h>
+#include <asm/dpmc.h>
+#include <linux/fs.h>
+#include <asm/bfin-global.h>
+
+/* CONFIG_CLKIN_HZ=11059200 */
+#define VCO5 (CONFIG_CLKIN_HZ*45)	/*497664000 */
+#define VCO4 (CONFIG_CLKIN_HZ*36)	/*398131200 */
+#define VCO3 (CONFIG_CLKIN_HZ*27)	/*298598400 */
+#define VCO2 (CONFIG_CLKIN_HZ*18)	/*199065600 */
+#define VCO1 (CONFIG_CLKIN_HZ*9)	/*99532800 */
+#define VCO(x) VCO##x
+
+#define MFREQ(x) {VCO(x), VCO(x)/4}, {VCO(x), VCO(x)/2}, {VCO(x), VCO(x)}
+/* frequency */
+static struct cpufreq_frequency_table bf527_freq_table[] = {
+	MFREQ(1),
+	MFREQ(3),
+	{VCO4, VCO4 / 2}, {VCO4, VCO4},
+	MFREQ(5),
+	{0, CPUFREQ_TABLE_END},
+};
+
+/*
+ * dpmc_fops->ioctl()
+ * static int dpmc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
+ */
+static int bf527_getfreq(unsigned int cpu)
+{
+	unsigned long cclk_mhz;
+
+	/* The driver only support single cpu */
+	if (cpu == 0)
+		dpmc_fops.ioctl(NULL, NULL, IOCTL_GET_CORECLOCK, &cclk_mhz);
+	else
+		cclk_mhz = -1;
+
+	return cclk_mhz;
+}
+
+static int bf527_target(struct cpufreq_policy *policy,
+			unsigned int target_freq, unsigned int relation)
+{
+	unsigned long cclk_mhz;
+	unsigned long vco_mhz;
+	unsigned long flags;
+	unsigned int index;
+	struct cpufreq_freqs freqs;
+
+	if (cpufreq_frequency_table_target
+	    (policy, bf527_freq_table, target_freq, relation, &index))
+		return -EINVAL;
+
+	cclk_mhz = bf527_freq_table[index].frequency;
+	vco_mhz = bf527_freq_table[index].index;
+
+	dpmc_fops.ioctl(NULL, NULL, IOCTL_CHANGE_FREQUENCY, &vco_mhz);
+	freqs.old = bf527_getfreq(0);
+	freqs.new = cclk_mhz;
+	freqs.cpu = 0;
+
+	pr_debug
+	    ("cclk begin change to cclk %d,vco=%d,index=%d,target=%d,oldfreq=%d\n",
+	     cclk_mhz, vco_mhz, index, target_freq, freqs.old);
+
+	cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+	local_irq_save(flags);
+	dpmc_fops.ioctl(NULL, NULL, IOCTL_SET_CCLK, &cclk_mhz);
+	local_irq_restore(flags);
+	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+	vco_mhz = get_vco();
+	cclk_mhz = get_cclk();
+	return 0;
+}
+
+/* make sure that only the "userspace" governor is run -- anything else wouldn't make sense on
+ * this platform, anyway.
+ */
+static int bf527_verify_speed(struct cpufreq_policy *policy)
+{
+	return cpufreq_frequency_table_verify(policy, &bf527_freq_table);
+}
+
+static int __init __bf527_cpu_init(struct cpufreq_policy *policy)
+{
+	if (policy->cpu != 0)
+		return -EINVAL;
+
+	policy->governor = CPUFREQ_DEFAULT_GOVERNOR;
+
+	policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;
+	/*Now ,only support one cpu */
+	policy->cur = bf527_getfreq(0);
+	cpufreq_frequency_table_get_attr(bf527_freq_table, policy->cpu);
+	return cpufreq_frequency_table_cpuinfo(policy, bf527_freq_table);
+}
+
+static struct freq_attr *bf527_freq_attr[] = {
+	&cpufreq_freq_attr_scaling_available_freqs,
+	NULL,
+};
+
+static struct cpufreq_driver bf527_driver = {
+	.verify = bf527_verify_speed,
+	.target = bf527_target,
+	.get = bf527_getfreq,
+	.init = __bf527_cpu_init,
+	.name = "bf527",
+	.owner = THIS_MODULE,
+	.attr = bf527_freq_attr,
+};
+
+static int __init bf527_cpu_init(void)
+{
+	return cpufreq_register_driver(&bf527_driver);
+}
+
+static void __exit bf527_cpu_exit(void)
+{
+	cpufreq_unregister_driver(&bf527_driver);
+}
+
+MODULE_AUTHOR("Mickael Kang");
+MODULE_DESCRIPTION("cpufreq driver for bf527 CPU");
+MODULE_LICENSE("GPL");
+
+module_init(bf527_cpu_init);
+module_exit(bf527_cpu_exit);
diff --git a/arch/blackfin/mach-bf527/dma.c b/arch/blackfin/mach-bf527/dma.c
new file mode 100644
index 00000000000..522de24cc39
--- /dev/null
+++ b/arch/blackfin/mach-bf527/dma.c
@@ -0,0 +1,115 @@
+/*
+ * File:         arch/blackfin/mach-bf527/dma.c
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  This file contains the simple DMA Implementation for Blackfin
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+#include <asm/blackfin.h>
+#include <asm/dma.h>
+
+struct dma_register *base_addr[MAX_BLACKFIN_DMA_CHANNEL] = {
+	(struct dma_register *) DMA0_NEXT_DESC_PTR,
+	(struct dma_register *) DMA1_NEXT_DESC_PTR,
+	(struct dma_register *) DMA2_NEXT_DESC_PTR,
+	(struct dma_register *) DMA3_NEXT_DESC_PTR,
+	(struct dma_register *) DMA4_NEXT_DESC_PTR,
+	(struct dma_register *) DMA5_NEXT_DESC_PTR,
+	(struct dma_register *) DMA6_NEXT_DESC_PTR,
+	(struct dma_register *) DMA7_NEXT_DESC_PTR,
+	(struct dma_register *) DMA8_NEXT_DESC_PTR,
+	(struct dma_register *) DMA9_NEXT_DESC_PTR,
+	(struct dma_register *) DMA10_NEXT_DESC_PTR,
+	(struct dma_register *) DMA11_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_D0_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_S0_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_D1_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_S1_NEXT_DESC_PTR,
+};
+
+int channel2irq(unsigned int channel)
+{
+	int ret_irq = -1;
+
+	switch (channel) {
+	case CH_PPI:
+		ret_irq = IRQ_PPI;
+		break;
+
+	case CH_EMAC_RX:
+		ret_irq = IRQ_MAC_RX;
+		break;
+
+	case CH_EMAC_TX:
+		ret_irq = IRQ_MAC_TX;
+		break;
+
+	case CH_UART1_RX:
+		ret_irq = IRQ_UART1_RX;
+		break;
+
+	case CH_UART1_TX:
+		ret_irq = IRQ_UART1_TX;
+		break;
+
+	case CH_SPORT0_RX:
+		ret_irq = IRQ_SPORT0_RX;
+		break;
+
+	case CH_SPORT0_TX:
+		ret_irq = IRQ_SPORT0_TX;
+		break;
+
+	case CH_SPORT1_RX:
+		ret_irq = IRQ_SPORT1_RX;
+		break;
+
+	case CH_SPORT1_TX:
+		ret_irq = IRQ_SPORT1_TX;
+		break;
+
+	case CH_SPI:
+		ret_irq = IRQ_SPI;
+		break;
+
+	case CH_UART0_RX:
+		ret_irq = IRQ_UART0_RX;
+		break;
+
+	case CH_UART0_TX:
+		ret_irq = IRQ_UART0_TX;
+		break;
+
+	case CH_MEM_STREAM0_SRC:
+	case CH_MEM_STREAM0_DEST:
+		ret_irq = IRQ_MEM_DMA0;
+		break;
+
+	case CH_MEM_STREAM1_SRC:
+	case CH_MEM_STREAM1_DEST:
+		ret_irq = IRQ_MEM_DMA1;
+		break;
+	}
+	return ret_irq;
+}
diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S
new file mode 100644
index 00000000000..cdb00a08496
--- /dev/null
+++ b/arch/blackfin/mach-bf527/head.S
@@ -0,0 +1,456 @@
+/*
+ * File:         arch/blackfin/mach-bf527/head.S
+ * Based on:     arch/blackfin/mach-bf533/head.S
+ * Author:       Jeff Dionne <jeff@uclinux.org> COPYRIGHT 1998 D. Jeff Dionne
+ *
+ * Created:      1998
+ * Description:  Startup code for Blackfin BF537
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/linkage.h>
+#include <linux/init.h>
+#include <asm/blackfin.h>
+#include <asm/trace.h>
+
+#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
+#include <asm/mach/mem_init.h>
+#endif
+
+.global __rambase
+.global __ramstart
+.global __ramend
+.extern ___bss_stop
+.extern ___bss_start
+.extern _bf53x_relocate_l1_mem
+
+#define INITIAL_STACK	0xFFB01000
+
+__INIT
+
+ENTRY(__start)
+	/* R0: argument of command line string, passed from uboot, save it */
+	R7 = R0;
+	/* Enable Cycle Counter and Nesting Of Interrupts */
+#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES
+	R0 = SYSCFG_SNEN;
+#else
+	R0 = SYSCFG_SNEN | SYSCFG_CCEN;
+#endif
+	SYSCFG = R0;
+	R0 = 0;
+
+	/* Clear Out All the data and pointer Registers */
+	R1 = R0;
+	R2 = R0;
+	R3 = R0;
+	R4 = R0;
+	R5 = R0;
+	R6 = R0;
+
+	P0 = R0;
+	P1 = R0;
+	P2 = R0;
+	P3 = R0;
+	P4 = R0;
+	P5 = R0;
+
+	LC0 = r0;
+	LC1 = r0;
+	L0 = r0;
+	L1 = r0;
+	L2 = r0;
+	L3 = r0;
+
+	/* Clear Out All the DAG Registers */
+	B0 = r0;
+	B1 = r0;
+	B2 = r0;
+	B3 = r0;
+
+	I0 = r0;
+	I1 = r0;
+	I2 = r0;
+	I3 = r0;
+
+	M0 = r0;
+	M1 = r0;
+	M2 = r0;
+	M3 = r0;
+
+	trace_buffer_init(p0,r0);
+	P0 = R1;
+	R0 = R1;
+
+	/* Turn off the icache */
+	p0.l = LO(IMEM_CONTROL);
+	p0.h = HI(IMEM_CONTROL);
+	R1 = [p0];
+	R0 = ~ENICPLB;
+	R0 = R0 & R1;
+
+	/* Anomaly 05000125 */
+#if ANOMALY_05000125
+	CLI R2;
+	SSYNC;
+#endif
+	[p0] = R0;
+	SSYNC;
+#if ANOMALY_05000125
+	STI R2;
+#endif
+
+	/* Turn off the dcache */
+	p0.l = LO(DMEM_CONTROL);
+	p0.h = HI(DMEM_CONTROL);
+	R1 = [p0];
+	R0 = ~ENDCPLB;
+	R0 = R0 & R1;
+
+	/* Anomaly 05000125 */
+#if ANOMALY_05000125
+	CLI R2;
+	SSYNC;
+#endif
+	[p0] = R0;
+	SSYNC;
+#if ANOMALY_05000125
+	STI R2;
+#endif
+
+
+#if defined(CONFIG_BF527)
+	p0.h = hi(EMAC_SYSTAT);
+	p0.l = lo(EMAC_SYSTAT);
+	R0.h = 0xFFFF; /* Clear EMAC Interrupt Status bits */
+	R0.l = 0xFFFF;
+	[P0] = R0;
+	SSYNC;
+#endif
+
+	/* Initialise UART - when booting from u-boot, the UART is not disabled
+	 * so if we dont initalize here, our serial console gets hosed */
+	p0.h = hi(UART1_LCR);
+	p0.l = lo(UART1_LCR);
+	r0 = 0x0(Z);
+	w[p0] = r0.L;	/* To enable DLL writes */
+	ssync;
+
+	p0.h = hi(UART1_DLL);
+	p0.l = lo(UART1_DLL);
+	r0 = 0x0(Z);
+	w[p0] = r0.L;
+	ssync;
+
+	p0.h = hi(UART1_DLH);
+	p0.l = lo(UART1_DLH);
+	r0 = 0x00(Z);
+	w[p0] = r0.L;
+	ssync;
+
+	p0.h = hi(UART1_GCTL);
+	p0.l = lo(UART1_GCTL);
+	r0 = 0x0(Z);
+	w[p0] = r0.L;	/* To enable UART clock */
+	ssync;
+
+	/* Initialize stack pointer */
+	sp.l = lo(INITIAL_STACK);
+	sp.h = hi(INITIAL_STACK);
+	fp = sp;
+	usp = sp;
+
+#ifdef CONFIG_EARLY_PRINTK
+	SP += -12;
+	call _init_early_exception_vectors;
+	SP += 12;
+#endif
+
+	/* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */
+	call _bf53x_relocate_l1_mem;
+#if CONFIG_BFIN_KERNEL_CLOCK
+	call _start_dma_code;
+#endif
+
+	/* Code for initializing Async memory banks */
+
+	p2.h = hi(EBIU_AMBCTL1);
+	p2.l = lo(EBIU_AMBCTL1);
+	r0.h = hi(AMBCTL1VAL);
+	r0.l = lo(AMBCTL1VAL);
+	[p2] = r0;
+	ssync;
+
+	p2.h = hi(EBIU_AMBCTL0);
+	p2.l = lo(EBIU_AMBCTL0);
+	r0.h = hi(AMBCTL0VAL);
+	r0.l = lo(AMBCTL0VAL);
+	[p2] = r0;
+	ssync;
+
+	p2.h = hi(EBIU_AMGCTL);
+	p2.l = lo(EBIU_AMGCTL);
+	r0 = AMGCTLVAL;
+	w[p2] = r0;
+	ssync;
+
+	/* This section keeps the processor in supervisor mode
+	 * during kernel boot.  Switches to user mode at end of boot.
+	 * See page 3-9 of Hardware Reference manual for documentation.
+	 */
+
+	/* EVT15 = _real_start */
+
+	p0.l = lo(EVT15);
+	p0.h = hi(EVT15);
+	p1.l = _real_start;
+	p1.h = _real_start;
+	[p0] = p1;
+	csync;
+
+	p0.l = lo(IMASK);
+	p0.h = hi(IMASK);
+	p1.l = IMASK_IVG15;
+	p1.h = 0x0;
+	[p0] = p1;
+	csync;
+
+	raise 15;
+	p0.l = .LWAIT_HERE;
+	p0.h = .LWAIT_HERE;
+	reti = p0;
+#if ANOMALY_05000281
+	nop; nop; nop;
+#endif
+	rti;
+
+.LWAIT_HERE:
+	jump .LWAIT_HERE;
+ENDPROC(__start)
+
+ENTRY(_real_start)
+	[ -- sp ] = reti;
+	p0.l = lo(WDOG_CTL);
+	p0.h = hi(WDOG_CTL);
+	r0 = 0xAD6(z);
+	w[p0] = r0;	/* watchdog off for now */
+	ssync;
+
+	/* Code update for BSS size == 0
+	 * Zero out the bss region.
+	 */
+
+	p1.l = ___bss_start;
+	p1.h = ___bss_start;
+	p2.l = ___bss_stop;
+	p2.h = ___bss_stop;
+	r0 = 0;
+	p2 -= p1;
+	lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2;
+.L_clear_bss:
+	B[p1++] = r0;
+
+	/* In case there is a NULL pointer reference
+	 * Zero out region before stext
+	 */
+
+	p1.l = 0x0;
+	p1.h = 0x0;
+	r0.l = __stext;
+	r0.h = __stext;
+	r0 = r0 >> 1;
+	p2 = r0;
+	r0 = 0;
+	lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2;
+.L_clear_zero:
+	W[p1++] = r0;
+
+	/* pass the uboot arguments to the global value command line */
+	R0 = R7;
+	call _cmdline_init;
+
+	p1.l = __rambase;
+	p1.h = __rambase;
+	r0.l = __sdata;
+	r0.h = __sdata;
+	[p1] = r0;
+
+	p1.l = __ramstart;
+	p1.h = __ramstart;
+	p3.l = ___bss_stop;
+	p3.h = ___bss_stop;
+
+	r1 = p3;
+	[p1] = r1;
+
+	/*
+	 * load the current thread pointer and stack
+	 */
+	r1.l = _init_thread_union;
+	r1.h = _init_thread_union;
+
+	r2.l = 0x2000;
+	r2.h = 0x0000;
+	r1 = r1 + r2;
+	sp = r1;
+	usp = sp;
+	fp = sp;
+	jump.l _start_kernel;
+ENDPROC(_real_start)
+
+__FINIT
+
+.section .l1.text
+#if CONFIG_BFIN_KERNEL_CLOCK
+ENTRY(_start_dma_code)
+
+	/* Enable PHY CLK buffer output */
+	p0.h = hi(VR_CTL);
+	p0.l = lo(VR_CTL);
+	r0.l = w[p0];
+	bitset(r0, 14);
+	w[p0] = r0.l;
+	ssync;
+
+	p0.h = hi(SIC_IWR0);
+	p0.l = lo(SIC_IWR0);
+	r0.l = 0x1;
+	r0.h = 0x0;
+	[p0] = r0;
+	SSYNC;
+
+	/*
+	 *  Set PLL_CTL
+	 *   - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+	 *   - [8]     = BYPASS    : BYPASS the PLL, run CLKIN into CCLK/SCLK
+	 *   - [7]     = output delay (add 200ps of delay to mem signals)
+	 *   - [6]     = input delay (add 200ps of input delay to mem signals)
+	 *   - [5]     = PDWN      : 1=All Clocks off
+	 *   - [3]     = STOPCK    : 1=Core Clock off
+	 *   - [1]     = PLL_OFF   : 1=Disable Power to PLL
+	 *   - [0]     = DF        : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+	 *   all other bits set to zero
+	 */
+
+	p0.h = hi(PLL_LOCKCNT);
+	p0.l = lo(PLL_LOCKCNT);
+	r0 = 0x300(Z);
+	w[p0] = r0.l;
+	ssync;
+
+	P2.H = hi(EBIU_SDGCTL);
+	P2.L = lo(EBIU_SDGCTL);
+	R0 = [P2];
+	BITSET (R0, 24);
+	[P2] = R0;
+	SSYNC;
+
+	r0 = CONFIG_VCO_MULT & 63;       /* Load the VCO multiplier         */
+	r0 = r0 << 9;                    /* Shift it over,                  */
+	r1 = CLKIN_HALF;                 /* Do we need to divide CLKIN by 2?*/
+	r0 = r1 | r0;
+	r1 = PLL_BYPASS;                 /* Bypass the PLL?                 */
+	r1 = r1 << 8;                    /* Shift it over                   */
+	r0 = r1 | r0;                    /* add them all together           */
+
+	p0.h = hi(PLL_CTL);
+	p0.l = lo(PLL_CTL);              /* Load the address                */
+	cli r2;                          /* Disable interrupts              */
+	ssync;
+	w[p0] = r0.l;                    /* Set the value                   */
+	idle;                            /* Wait for the PLL to stablize    */
+	sti r2;                          /* Enable interrupts               */
+
+.Lcheck_again:
+	p0.h = hi(PLL_STAT);
+	p0.l = lo(PLL_STAT);
+	R0 = W[P0](Z);
+	CC = BITTST(R0,5);
+	if ! CC jump .Lcheck_again;
+
+	/* Configure SCLK & CCLK Dividers */
+	r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+	p0.h = hi(PLL_DIV);
+	p0.l = lo(PLL_DIV);
+	w[p0] = r0.l;
+	ssync;
+
+	p0.l = lo(EBIU_SDRRC);
+	p0.h = hi(EBIU_SDRRC);
+	r0 = mem_SDRRC;
+	w[p0] = r0.l;
+	ssync;
+
+	p0.l = LO(EBIU_SDBCTL);
+	p0.h = HI(EBIU_SDBCTL);     /* SDRAM Memory Bank Control Register */
+	r0 = mem_SDBCTL;
+	w[p0] = r0.l;
+	ssync;
+
+	P2.H = hi(EBIU_SDGCTL);
+	P2.L = lo(EBIU_SDGCTL);
+	R0 = [P2];
+	BITCLR (R0, 24);
+	p0.h = hi(EBIU_SDSTAT);
+	p0.l = lo(EBIU_SDSTAT);
+	r2.l = w[p0];
+	cc = bittst(r2,3);
+	if !cc jump .Lskip;
+	NOP;
+	BITSET (R0, 23);
+.Lskip:
+	[P2] = R0;
+	SSYNC;
+
+	R0.L = lo(mem_SDGCTL);
+	R0.H = hi(mem_SDGCTL);
+	R1 = [p2];
+	R1 = R1 | R0;
+	[P2] = R1;
+	SSYNC;
+
+	p0.h = hi(SIC_IWR0);
+	p0.l = lo(SIC_IWR0);
+	r0.l = lo(IWR_ENABLE_ALL);
+	r0.h = hi(IWR_ENABLE_ALL);
+	[p0] = r0;
+	SSYNC;
+
+	RTS;
+ENDPROC(_start_dma_code)
+#endif /* CONFIG_BFIN_KERNEL_CLOCK */
+
+.data
+
+/*
+ * Set up the usable of RAM stuff. Size of RAM is determined then
+ * an initial stack set up at the end.
+ */
+
+.align 4
+__rambase:
+.long   0
+__ramstart:
+.long   0
+__ramend:
+.long   0
diff --git a/arch/blackfin/mach-bf527/ints-priority.c b/arch/blackfin/mach-bf527/ints-priority.c
new file mode 100644
index 00000000000..1fa38979396
--- /dev/null
+++ b/arch/blackfin/mach-bf527/ints-priority.c
@@ -0,0 +1,100 @@
+/*
+ * File:         arch/blackfin/mach-bf537/ints-priority.c
+ * Based on:     arch/blackfin/mach-bf533/ints-priority.c
+ * Author:       Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * Created:
+ * Description:  Set up the interrupt priorities
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/module.h>
+#include <linux/irq.h>
+#include <asm/blackfin.h>
+
+void program_IAR(void)
+{
+	/* Program the IAR0 Register with the configured priority */
+	bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) |
+			((CONFIG_IRQ_DMA0_ERROR - 7) << IRQ_DMA0_ERROR_POS) |
+			((CONFIG_IRQ_DMAR0_BLK - 7) << IRQ_DMAR0_BLK_POS) |
+			((CONFIG_IRQ_DMAR1_BLK - 7) << IRQ_DMAR1_BLK_POS) |
+			((CONFIG_IRQ_DMAR0_OVR - 7) << IRQ_DMAR0_OVR_POS) |
+			((CONFIG_IRQ_DMAR1_OVR - 7) << IRQ_DMAR1_OVR_POS) |
+			((CONFIG_IRQ_PPI_ERROR - 7) << IRQ_PPI_ERROR_POS) |
+			((CONFIG_IRQ_MAC_ERROR - 7) << IRQ_MAC_ERROR_POS));
+
+
+	bfin_write_SIC_IAR1(((CONFIG_IRQ_SPORT0_ERROR - 7) << IRQ_SPORT0_ERROR_POS) |
+			((CONFIG_IRQ_SPORT1_ERROR - 7) << IRQ_SPORT1_ERROR_POS) |
+			((CONFIG_IRQ_UART0_ERROR - 7) << IRQ_UART0_ERROR_POS) |
+			((CONFIG_IRQ_UART1_ERROR - 7) << IRQ_UART1_ERROR_POS) |
+			((CONFIG_IRQ_RTC - 7) << IRQ_RTC_POS) |
+			((CONFIG_IRQ_PPI - 7) << IRQ_PPI_POS));
+
+	bfin_write_SIC_IAR2(((CONFIG_IRQ_SPORT0_RX - 7) << IRQ_SPORT0_RX_POS) |
+			((CONFIG_IRQ_SPORT0_TX - 7) << IRQ_SPORT0_TX_POS) |
+			((CONFIG_IRQ_SPORT1_RX - 7) << IRQ_SPORT1_RX_POS) |
+			((CONFIG_IRQ_SPORT1_TX - 7) << IRQ_SPORT1_TX_POS) |
+			((CONFIG_IRQ_TWI - 7) << IRQ_TWI_POS) |
+			((CONFIG_IRQ_SPI - 7) << IRQ_SPI_POS) |
+			((CONFIG_IRQ_UART0_RX - 7) << IRQ_UART0_RX_POS) |
+			((CONFIG_IRQ_UART0_TX - 7) << IRQ_UART0_TX_POS));
+
+	bfin_write_SIC_IAR3(((CONFIG_IRQ_UART1_RX - 7) << IRQ_UART1_RX_POS) |
+			((CONFIG_IRQ_UART1_TX - 7) << IRQ_UART1_TX_POS) |
+			((CONFIG_IRQ_OPTSEC - 7) << IRQ_OPTSEC_POS) |
+			((CONFIG_IRQ_CNT - 7) << IRQ_CNT_POS) |
+			((CONFIG_IRQ_MAC_RX - 7) << IRQ_MAC_RX_POS) |
+			((CONFIG_IRQ_PORTH_INTA - 7) << IRQ_PORTH_INTA_POS) |
+			((CONFIG_IRQ_MAC_TX - 7) << IRQ_MAC_TX_POS) |
+			((CONFIG_IRQ_PORTH_INTB - 7) << IRQ_PORTH_INTB_POS));
+
+	bfin_write_SIC_IAR4(((CONFIG_IRQ_TMR0 - 7) << IRQ_TMR0_POS) |
+			((CONFIG_IRQ_TMR1 - 7) << IRQ_TMR1_POS) |
+			((CONFIG_IRQ_TMR2 - 7) << IRQ_TMR2_POS) |
+			((CONFIG_IRQ_TMR3 - 7) << IRQ_TMR3_POS) |
+			((CONFIG_IRQ_TMR4 - 7) << IRQ_TMR4_POS) |
+			((CONFIG_IRQ_TMR5 - 7) << IRQ_TMR5_POS) |
+			((CONFIG_IRQ_TMR6 - 7) << IRQ_TMR6_POS) |
+			((CONFIG_IRQ_TMR7 - 7) << IRQ_TMR7_POS));
+
+	bfin_write_SIC_IAR5(((CONFIG_IRQ_PORTG_INTA - 7) << IRQ_PORTG_INTA_POS) |
+			((CONFIG_IRQ_PORTG_INTB - 7) << IRQ_PORTG_INTB_POS) |
+			((CONFIG_IRQ_MEM_DMA0 - 7) << IRQ_MEM_DMA0_POS) |
+			((CONFIG_IRQ_MEM_DMA1 - 7) << IRQ_MEM_DMA1_POS) |
+			((CONFIG_IRQ_WATCH - 7) << IRQ_WATCH_POS) |
+			((CONFIG_IRQ_PORTF_INTA - 7) << IRQ_PORTF_INTA_POS) |
+			((CONFIG_IRQ_PORTF_INTB - 7) << IRQ_PORTF_INTB_POS) |
+			((CONFIG_IRQ_SPI_ERROR - 7) << IRQ_SPI_ERROR_POS));
+
+	bfin_write_SIC_IAR6(((CONFIG_IRQ_NFC_ERROR - 7) << IRQ_NFC_ERROR_POS) |
+			((CONFIG_IRQ_HDMA_ERROR - 7) << IRQ_HDMA_ERROR_POS) |
+			((CONFIG_IRQ_HDMA - 7) << IRQ_HDMA_POS) |
+			((CONFIG_IRQ_USB_EINT - 7) << IRQ_USB_EINT_POS) |
+			((CONFIG_IRQ_USB_INT0 - 7) << IRQ_USB_INT0_POS) |
+			((CONFIG_IRQ_USB_INT1 - 7) << IRQ_USB_INT1_POS) |
+			((CONFIG_IRQ_USB_INT2 - 7) << IRQ_USB_INT2_POS) |
+			((CONFIG_IRQ_USB_DMA - 7) << IRQ_USB_DMA_POS));
+
+	SSYNC();
+}