cris build fixes: corrected and improved NMI and IRQ handling

Corrects compile errors and the following:

- Remove oldset parameter from do_signal and do_notify_resume.

- Modified to fit new consolidated IRQ handling code.

- Reverse check order between external nmi and watchdog nmi to avoid false
  watchdog oops in case of a glitch on the nmi pin.

- Return from an pin-generated NMI the same way as for other interrupts.

- Moved blocking of ethernet rx/tx irq from ethernet interrupt handler to
  low-level asm interrupt handlers.  Fixed in the multiple interrupt
  handler also.

- Add space for thread local storage in thread_info struct.

- Add NO_DMA to Kconfig, and include arch specific Kconfig using arch
  independent path. Include subsystem Kconfigs for pcmcia, usb, i2c,
  rtc and pci.

Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1 files changed, 57 insertions, 2 deletions

diff --git a/arch/cris/arch-v10/kernel/irq.c b/arch/cris/arch-v10/kernel/irq.c
index 845c95f6e87..e06ab0050d3 100644
--- a/arch/cris/arch-v10/kernel/irq.c
+++ b/arch/cris/arch-v10/kernel/irq.c
@@ -12,10 +12,16 @@
  */
 
 #include <asm/irq.h>
+#include <asm/current.h>
 #include <linux/irq.h>
+#include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 
+/* From kgdb.c. */
+extern void kgdb_init(void);
+extern void breakpoint(void);
+
 #define mask_irq(irq_nr) (*R_VECT_MASK_CLR = 1 << (irq_nr));
 #define unmask_irq(irq_nr) (*R_VECT_MASK_SET = 1 << (irq_nr));
 
@@ -75,8 +81,8 @@ BUILD_IRQ(12, 0x1000)
 BUILD_IRQ(13, 0x2000)
 void mmu_bus_fault(void);      /* IRQ 14 is the bus fault interrupt */
 void multiple_interrupt(void); /* IRQ 15 is the multiple IRQ interrupt */
-BUILD_IRQ(16, 0x10000)
-BUILD_IRQ(17, 0x20000)
+BUILD_IRQ(16, 0x10000 | 0x20000)  /* ethernet tx interrupt needs to block rx */
+BUILD_IRQ(17, 0x20000 | 0x10000)  /* ...and vice versa */
 BUILD_IRQ(18, 0x40000)
 BUILD_IRQ(19, 0x80000)
 BUILD_IRQ(20, 0x100000)
@@ -147,6 +153,55 @@ void system_call(void);  /* from entry.S */
 void do_sigtrap(void); /* from entry.S */
 void gdb_handle_breakpoint(void); /* from entry.S */
 
+extern void do_IRQ(int irq, struct pt_regs * regs);
+
+/* Handle multiple IRQs */
+void do_multiple_IRQ(struct pt_regs* regs)
+{
+	int bit;
+	unsigned masked;
+	unsigned mask;
+	unsigned ethmask = 0;
+
+	/* Get interrupts to mask and handle */
+	mask = masked = *R_VECT_MASK_RD;
+
+	/* Never mask timer IRQ */
+	mask &= ~(IO_MASK(R_VECT_MASK_RD, timer0));
+
+	/*
+	 * If either ethernet interrupt (rx or tx) is active then block
+	 * the other one too. Unblock afterwards also.
+	 */
+	if (mask &
+	    (IO_STATE(R_VECT_MASK_RD, dma0, active) |
+	     IO_STATE(R_VECT_MASK_RD, dma1, active))) {
+		ethmask = (IO_MASK(R_VECT_MASK_RD, dma0) |
+			   IO_MASK(R_VECT_MASK_RD, dma1));
+	}
+
+	/* Block them */
+	*R_VECT_MASK_CLR = (mask | ethmask);
+
+	/* An extra irq_enter here to prevent softIRQs to run after
+	 * each do_IRQ. This will decrease the interrupt latency.
+	 */
+	irq_enter();
+
+	/* Handle all IRQs */
+	for (bit = 2; bit < 32; bit++) {
+		if (masked & (1 << bit)) {
+			do_IRQ(bit, regs);
+		}
+	}
+
+	/* This irq_exit() will trigger the soft IRQs. */
+	irq_exit();
+
+	/* Unblock the IRQs again */
+	*R_VECT_MASK_SET = (masked | ethmask);
+}
+
 /* init_IRQ() is called by start_kernel and is responsible for fixing IRQ masks and
    setting the irq vector table.
 */