i386: prepare shared kernel/trampoline.S

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

1 files changed, 0 insertions, 85 deletions

diff --git a/arch/i386/kernel/trampoline.S b/arch/i386/kernel/trampoline.S
deleted file mode 100644
index f62815f8d06..00000000000
--- a/arch/i386/kernel/trampoline.S
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
- *
- *	Trampoline.S	Derived from Setup.S by Linus Torvalds
- *
- *	4 Jan 1997 Michael Chastain: changed to gnu as.
- *
- *	This is only used for booting secondary CPUs in SMP machine
- *
- *	Entry: CS:IP point to the start of our code, we are 
- *	in real mode with no stack, but the rest of the 
- *	trampoline page to make our stack and everything else
- *	is a mystery.
- *
- *	In fact we don't actually need a stack so we don't
- *	set one up.
- *
- *	We jump into the boot/compressed/head.S code. So you'd
- *	better be running a compressed kernel image or you
- *	won't get very far.
- *
- *	On entry to trampoline_data, the processor is in real mode
- *	with 16-bit addressing and 16-bit data.  CS has some value
- *	and IP is zero.  Thus, data addresses need to be absolute
- *	(no relocation) and are taken with regard to r_base.
- *
- *	If you work on this file, check the object module with
- *	objdump --reloc to make sure there are no relocation
- *	entries except for:
- *
- *	TYPE              VALUE
- *	R_386_32          startup_32_smp
- *	R_386_32          boot_gdt
- */
-
-#include <linux/linkage.h>
-#include <asm/segment.h>
-#include <asm/page.h>
-
-.data
-
-/* We can free up trampoline after bootup if cpu hotplug is not supported. */
-#ifndef CONFIG_HOTPLUG_CPU
-.section ".init.data","aw",@progbits
-#endif
-
-.code16
-
-ENTRY(trampoline_data)
-r_base = .
-	wbinvd			# Needed for NUMA-Q should be harmless for others
-	mov	%cs, %ax	# Code and data in the same place
-	mov	%ax, %ds
-
-	cli			# We should be safe anyway
-
-	movl	$0xA5A5A5A5, trampoline_data - r_base
-				# write marker for master knows we're running
-
-	/* GDT tables in non default location kernel can be beyond 16MB and
-	 * lgdt will not be able to load the address as in real mode default
-	 * operand size is 16bit. Use lgdtl instead to force operand size
-	 * to 32 bit.
-	 */
-
-	lidtl	boot_idt_descr - r_base	# load idt with 0, 0
-	lgdtl	boot_gdt_descr - r_base	# load gdt with whatever is appropriate
-
-	xor	%ax, %ax
-	inc	%ax		# protected mode (PE) bit
-	lmsw	%ax		# into protected mode
-	# flush prefetch and jump to startup_32_smp in arch/i386/kernel/head.S
-	ljmpl	$__BOOT_CS, $(startup_32_smp-__PAGE_OFFSET)
-
-	# These need to be in the same 64K segment as the above;
-	# hence we don't use the boot_gdt_descr defined in head.S
-boot_gdt_descr:
-	.word	__BOOT_DS + 7			# gdt limit
-	.long	boot_gdt - __PAGE_OFFSET	# gdt base
-
-boot_idt_descr:
-	.word	0				# idt limit = 0
-	.long	0				# idt base = 0L
-
-.globl trampoline_end
-trampoline_end: