Move all of include/asm-m68knommu to arch/m68knommu/include/asm.

With the current kbuild infrastructure in place no other changes
are required for this to work.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>

1 files changed, 1253 insertions, 0 deletions

diff --git a/arch/m68knommu/include/asm/MC68EZ328.h b/arch/m68knommu/include/asm/MC68EZ328.h
new file mode 100644
index 00000000000..69b7f9139e5
--- /dev/null
+++ b/arch/m68knommu/include/asm/MC68EZ328.h
@@ -0,0 +1,1253 @@
+
+/* include/asm-m68knommu/MC68EZ328.h: 'EZ328 control registers
+ *
+ * Copyright (C) 1999  Vladimir Gurevich <vgurevic@cisco.com>
+ *                     Bear & Hare Software, Inc.
+ *
+ * Based on include/asm-m68knommu/MC68332.h
+ * Copyright (C) 1998  Kenneth Albanowski <kjahds@kjahds.com>,
+ *                     The Silver Hammer Group, Ltd.
+ *
+ */
+
+#ifndef _MC68EZ328_H_
+#define _MC68EZ328_H_
+
+#define BYTE_REF(addr) (*((volatile unsigned char*)addr))
+#define WORD_REF(addr) (*((volatile unsigned short*)addr))
+#define LONG_REF(addr) (*((volatile unsigned long*)addr))
+
+#define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK)
+#define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT)
+
+/********** 
+ *
+ * 0xFFFFF0xx -- System Control
+ *
+ **********/
+ 
+/*
+ * System Control Register (SCR)
+ */
+#define SCR_ADDR	0xfffff000
+#define SCR		BYTE_REF(SCR_ADDR)
+
+#define SCR_WDTH8	0x01	/* 8-Bit Width Select */
+#define SCR_DMAP	0x04	/* Double Map */
+#define SCR_SO		0x08	/* Supervisor Only */
+#define SCR_BETEN	0x10	/* Bus-Error Time-Out Enable */
+#define SCR_PRV		0x20	/* Privilege Violation */
+#define SCR_WPV		0x40	/* Write Protect Violation */
+#define SCR_BETO	0x80	/* Bus-Error TimeOut */
+
+/*
+ * Silicon ID Register (Mask Revision Register (MRR) for '328 Compatibility)
+ */
+#define MRR_ADDR 0xfffff004
+#define MRR	 LONG_REF(MRR_ADDR)
+
+/********** 
+ *
+ * 0xFFFFF1xx -- Chip-Select logic
+ *
+ **********/
+ 
+/*
+ * Chip Select Group Base Registers 
+ */
+#define CSGBA_ADDR	0xfffff100
+#define CSGBB_ADDR	0xfffff102
+
+#define CSGBC_ADDR	0xfffff104
+#define CSGBD_ADDR	0xfffff106
+
+#define CSGBA		WORD_REF(CSGBA_ADDR)
+#define CSGBB		WORD_REF(CSGBB_ADDR)
+#define CSGBC		WORD_REF(CSGBC_ADDR)
+#define CSGBD		WORD_REF(CSGBD_ADDR)
+
+/*
+ * Chip Select Registers 
+ */
+#define CSA_ADDR	0xfffff110
+#define CSB_ADDR	0xfffff112
+#define CSC_ADDR	0xfffff114
+#define CSD_ADDR	0xfffff116
+
+#define CSA		WORD_REF(CSA_ADDR)
+#define CSB		WORD_REF(CSB_ADDR)
+#define CSC		WORD_REF(CSC_ADDR)
+#define CSD		WORD_REF(CSD_ADDR)
+
+#define CSA_EN		0x0001		/* Chip-Select Enable */
+#define CSA_SIZ_MASK	0x000e		/* Chip-Select Size */
+#define CSA_SIZ_SHIFT   1
+#define CSA_WS_MASK	0x0070		/* Wait State */
+#define CSA_WS_SHIFT    4
+#define CSA_BSW		0x0080		/* Data Bus Width */
+#define CSA_FLASH	0x0100		/* FLASH Memory Support */
+#define CSA_RO		0x8000		/* Read-Only */
+
+#define CSB_EN		0x0001		/* Chip-Select Enable */
+#define CSB_SIZ_MASK	0x000e		/* Chip-Select Size */
+#define CSB_SIZ_SHIFT   1
+#define CSB_WS_MASK	0x0070		/* Wait State */
+#define CSB_WS_SHIFT    4
+#define CSB_BSW		0x0080		/* Data Bus Width */
+#define CSB_FLASH	0x0100		/* FLASH Memory Support */
+#define CSB_UPSIZ_MASK	0x1800		/* Unprotected memory block size */
+#define CSB_UPSIZ_SHIFT 11
+#define CSB_ROP		0x2000		/* Readonly if protected */
+#define CSB_SOP		0x4000		/* Supervisor only if protected */
+#define CSB_RO		0x8000		/* Read-Only */
+
+#define CSC_EN		0x0001		/* Chip-Select Enable */
+#define CSC_SIZ_MASK	0x000e		/* Chip-Select Size */
+#define CSC_SIZ_SHIFT   1
+#define CSC_WS_MASK	0x0070		/* Wait State */
+#define CSC_WS_SHIFT    4
+#define CSC_BSW		0x0080		/* Data Bus Width */
+#define CSC_FLASH	0x0100		/* FLASH Memory Support */
+#define CSC_UPSIZ_MASK	0x1800		/* Unprotected memory block size */
+#define CSC_UPSIZ_SHIFT 11
+#define CSC_ROP		0x2000		/* Readonly if protected */
+#define CSC_SOP		0x4000		/* Supervisor only if protected */
+#define CSC_RO		0x8000		/* Read-Only */
+
+#define CSD_EN		0x0001		/* Chip-Select Enable */
+#define CSD_SIZ_MASK	0x000e		/* Chip-Select Size */
+#define CSD_SIZ_SHIFT   1
+#define CSD_WS_MASK	0x0070		/* Wait State */
+#define CSD_WS_SHIFT    4
+#define CSD_BSW		0x0080		/* Data Bus Width */
+#define CSD_FLASH	0x0100		/* FLASH Memory Support */
+#define CSD_DRAM	0x0200		/* Dram Selection */
+#define	CSD_COMB	0x0400		/* Combining */
+#define CSD_UPSIZ_MASK	0x1800		/* Unprotected memory block size */
+#define CSD_UPSIZ_SHIFT 11
+#define CSD_ROP		0x2000		/* Readonly if protected */
+#define CSD_SOP		0x4000		/* Supervisor only if protected */
+#define CSD_RO		0x8000		/* Read-Only */
+
+/*
+ * Emulation Chip-Select Register 
+ */
+#define EMUCS_ADDR	0xfffff118
+#define EMUCS		WORD_REF(EMUCS_ADDR)
+
+#define EMUCS_WS_MASK	0x0070
+#define EMUCS_WS_SHIFT	4
+
+/********** 
+ *
+ * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control
+ *
+ **********/
+
+/*
+ * PLL Control Register 
+ */
+#define PLLCR_ADDR	0xfffff200
+#define PLLCR		WORD_REF(PLLCR_ADDR)
+
+#define PLLCR_DISPLL	       0x0008	/* Disable PLL */
+#define PLLCR_CLKEN	       0x0010	/* Clock (CLKO pin) enable */
+#define PLLCR_PRESC	       0x0020	/* VCO prescaler */
+#define PLLCR_SYSCLK_SEL_MASK  0x0700	/* System Clock Selection */
+#define PLLCR_SYSCLK_SEL_SHIFT 8
+#define PLLCR_LCDCLK_SEL_MASK  0x3800	/* LCD Clock Selection */
+#define PLLCR_LCDCLK_SEL_SHIFT 11
+
+/* '328-compatible definitions */
+#define PLLCR_PIXCLK_SEL_MASK	PLLCR_LCDCLK_SEL_MASK
+#define PLLCR_PIXCLK_SEL_SHIFT	PLLCR_LCDCLK_SEL_SHIFT
+
+/*
+ * PLL Frequency Select Register
+ */
+#define PLLFSR_ADDR	0xfffff202
+#define PLLFSR		WORD_REF(PLLFSR_ADDR)
+
+#define PLLFSR_PC_MASK	0x00ff		/* P Count */
+#define PLLFSR_PC_SHIFT 0
+#define PLLFSR_QC_MASK	0x0f00		/* Q Count */
+#define PLLFSR_QC_SHIFT 8
+#define PLLFSR_PROT	0x4000		/* Protect P & Q */
+#define PLLFSR_CLK32	0x8000		/* Clock 32 (kHz) */
+
+/*
+ * Power Control Register
+ */
+#define PCTRL_ADDR	0xfffff207
+#define PCTRL		BYTE_REF(PCTRL_ADDR)
+
+#define PCTRL_WIDTH_MASK	0x1f	/* CPU Clock bursts width */
+#define PCTRL_WIDTH_SHIFT	0
+#define PCTRL_PCEN		0x80	/* Power Control Enable */
+
+/**********
+ *
+ * 0xFFFFF3xx -- Interrupt Controller
+ *
+ **********/
+
+/* 
+ * Interrupt Vector Register
+ */
+#define IVR_ADDR	0xfffff300
+#define IVR		BYTE_REF(IVR_ADDR)
+
+#define IVR_VECTOR_MASK 0xF8
+
+/*
+ * Interrupt control Register
+ */
+#define ICR_ADDR	0xfffff302
+#define ICR		WORD_REF(ICR_ADDR)
+
+#define ICR_POL5	0x0080	/* Polarity Control for IRQ5 */
+#define ICR_ET6		0x0100	/* Edge Trigger Select for IRQ6 */
+#define ICR_ET3		0x0200	/* Edge Trigger Select for IRQ3 */
+#define ICR_ET2		0x0400	/* Edge Trigger Select for IRQ2 */
+#define ICR_ET1		0x0800	/* Edge Trigger Select for IRQ1 */
+#define ICR_POL6	0x1000	/* Polarity Control for IRQ6 */
+#define ICR_POL3	0x2000	/* Polarity Control for IRQ3 */
+#define ICR_POL2	0x4000	/* Polarity Control for IRQ2 */
+#define ICR_POL1	0x8000	/* Polarity Control for IRQ1 */
+
+/*
+ * Interrupt Mask Register
+ */
+#define IMR_ADDR	0xfffff304
+#define IMR		LONG_REF(IMR_ADDR)
+
+/*
+ * Define the names for bit positions first. This is useful for 
+ * request_irq
+ */
+#define SPI_IRQ_NUM	0	/* SPI interrupt */
+#define TMR_IRQ_NUM	1	/* Timer interrupt */
+#define UART_IRQ_NUM	2	/* UART interrupt */	
+#define	WDT_IRQ_NUM	3	/* Watchdog Timer interrupt */
+#define RTC_IRQ_NUM	4	/* RTC interrupt */
+#define	KB_IRQ_NUM	6	/* Keyboard Interrupt */
+#define PWM_IRQ_NUM	7	/* Pulse-Width Modulator int. */
+#define	INT0_IRQ_NUM	8	/* External INT0 */
+#define	INT1_IRQ_NUM	9	/* External INT1 */
+#define	INT2_IRQ_NUM	10	/* External INT2 */
+#define	INT3_IRQ_NUM	11	/* External INT3 */
+#define IRQ1_IRQ_NUM	16	/* IRQ1 */
+#define IRQ2_IRQ_NUM	17	/* IRQ2 */
+#define IRQ3_IRQ_NUM	18	/* IRQ3 */
+#define IRQ6_IRQ_NUM	19	/* IRQ6 */
+#define IRQ5_IRQ_NUM	20	/* IRQ5 */
+#define SAM_IRQ_NUM	22	/* Sampling Timer for RTC */
+#define EMIQ_IRQ_NUM	23	/* Emulator Interrupt */
+
+/* '328-compatible definitions */
+#define SPIM_IRQ_NUM	SPI_IRQ_NUM
+#define TMR1_IRQ_NUM	TMR_IRQ_NUM
+
+/* 
+ * Here go the bitmasks themselves
+ */
+#define IMR_MSPI 	(1 << SPI_IRQ_NUM)	/* Mask SPI interrupt */
+#define	IMR_MTMR	(1 << TMR_IRQ_NUM)	/* Mask Timer interrupt */
+#define IMR_MUART	(1 << UART_IRQ_NUM)	/* Mask UART interrupt */	
+#define	IMR_MWDT	(1 << WDT_IRQ_NUM)	/* Mask Watchdog Timer interrupt */
+#define IMR_MRTC	(1 << RTC_IRQ_NUM)	/* Mask RTC interrupt */
+#define	IMR_MKB		(1 << KB_IRQ_NUM)	/* Mask Keyboard Interrupt */
+#define IMR_MPWM	(1 << PWM_IRQ_NUM)	/* Mask Pulse-Width Modulator int. */
+#define	IMR_MINT0	(1 << INT0_IRQ_NUM)	/* Mask External INT0 */
+#define	IMR_MINT1	(1 << INT1_IRQ_NUM)	/* Mask External INT1 */
+#define	IMR_MINT2	(1 << INT2_IRQ_NUM)	/* Mask External INT2 */
+#define	IMR_MINT3	(1 << INT3_IRQ_NUM)	/* Mask External INT3 */
+#define IMR_MIRQ1	(1 << IRQ1_IRQ_NUM)	/* Mask IRQ1 */
+#define IMR_MIRQ2	(1 << IRQ2_IRQ_NUM)	/* Mask IRQ2 */
+#define IMR_MIRQ3	(1 << IRQ3_IRQ_NUM)	/* Mask IRQ3 */
+#define IMR_MIRQ6	(1 << IRQ6_IRQ_NUM)	/* Mask IRQ6 */
+#define IMR_MIRQ5	(1 << IRQ5_IRQ_NUM)	/* Mask IRQ5 */
+#define IMR_MSAM	(1 << SAM_IRQ_NUM)	/* Mask Sampling Timer for RTC */
+#define IMR_MEMIQ	(1 << EMIQ_IRQ_NUM)	/* Mask Emulator Interrupt */
+
+/* '328-compatible definitions */
+#define IMR_MSPIM	IMR_MSPI
+#define IMR_MTMR1	IMR_MTMR
+
+/* 
+ * Interrupt Status Register 
+ */
+#define ISR_ADDR	0xfffff30c
+#define ISR		LONG_REF(ISR_ADDR)
+
+#define ISR_SPI 	(1 << SPI_IRQ_NUM)	/* SPI interrupt */
+#define	ISR_TMR		(1 << TMR_IRQ_NUM)	/* Timer interrupt */
+#define ISR_UART	(1 << UART_IRQ_NUM)	/* UART interrupt */	
+#define	ISR_WDT		(1 << WDT_IRQ_NUM)	/* Watchdog Timer interrupt */
+#define ISR_RTC		(1 << RTC_IRQ_NUM)	/* RTC interrupt */
+#define	ISR_KB		(1 << KB_IRQ_NUM)	/* Keyboard Interrupt */
+#define ISR_PWM		(1 << PWM_IRQ_NUM)	/* Pulse-Width Modulator interrupt */
+#define	ISR_INT0	(1 << INT0_IRQ_NUM)	/* External INT0 */
+#define	ISR_INT1	(1 << INT1_IRQ_NUM)	/* External INT1 */
+#define	ISR_INT2	(1 << INT2_IRQ_NUM)	/* External INT2 */
+#define	ISR_INT3	(1 << INT3_IRQ_NUM)	/* External INT3 */
+#define ISR_IRQ1	(1 << IRQ1_IRQ_NUM)	/* IRQ1 */
+#define ISR_IRQ2	(1 << IRQ2_IRQ_NUM)	/* IRQ2 */
+#define ISR_IRQ3	(1 << IRQ3_IRQ_NUM)	/* IRQ3 */
+#define ISR_IRQ6	(1 << IRQ6_IRQ_NUM)	/* IRQ6 */
+#define ISR_IRQ5	(1 << IRQ5_IRQ_NUM)	/* IRQ5 */
+#define ISR_SAM		(1 << SAM_IRQ_NUM)	/* Sampling Timer for RTC */
+#define ISR_EMIQ	(1 << EMIQ_IRQ_NUM)	/* Emulator Interrupt */
+
+/* '328-compatible definitions */
+#define ISR_SPIM	ISR_SPI
+#define ISR_TMR1	ISR_TMR
+
+/* 
+ * Interrupt Pending Register 
+ */
+#define IPR_ADDR	0xfffff30c
+#define IPR		LONG_REF(IPR_ADDR)
+
+#define IPR_SPI 	(1 << SPI_IRQ_NUM)	/* SPI interrupt */
+#define	IPR_TMR		(1 << TMR_IRQ_NUM)	/* Timer interrupt */
+#define IPR_UART	(1 << UART_IRQ_NUM)	/* UART interrupt */	
+#define	IPR_WDT		(1 << WDT_IRQ_NUM)	/* Watchdog Timer interrupt */
+#define IPR_RTC		(1 << RTC_IRQ_NUM)	/* RTC interrupt */
+#define	IPR_KB		(1 << KB_IRQ_NUM)	/* Keyboard Interrupt */
+#define IPR_PWM		(1 << PWM_IRQ_NUM)	/* Pulse-Width Modulator interrupt */
+#define	IPR_INT0	(1 << INT0_IRQ_NUM)	/* External INT0 */
+#define	IPR_INT1	(1 << INT1_IRQ_NUM)	/* External INT1 */
+#define	IPR_INT2	(1 << INT2_IRQ_NUM)	/* External INT2 */
+#define	IPR_INT3	(1 << INT3_IRQ_NUM)	/* External INT3 */
+#define IPR_IRQ1	(1 << IRQ1_IRQ_NUM)	/* IRQ1 */
+#define IPR_IRQ2	(1 << IRQ2_IRQ_NUM)	/* IRQ2 */
+#define IPR_IRQ3	(1 << IRQ3_IRQ_NUM)	/* IRQ3 */
+#define IPR_IRQ6	(1 << IRQ6_IRQ_NUM)	/* IRQ6 */
+#define IPR_IRQ5	(1 << IRQ5_IRQ_NUM)	/* IRQ5 */
+#define IPR_SAM		(1 << SAM_IRQ_NUM)	/* Sampling Timer for RTC */
+#define IPR_EMIQ	(1 << EMIQ_IRQ_NUM)	/* Emulator Interrupt */
+
+/* '328-compatible definitions */
+#define IPR_SPIM	IPR_SPI
+#define IPR_TMR1	IPR_TMR
+
+/**********
+ *
+ * 0xFFFFF4xx -- Parallel Ports
+ *
+ **********/
+
+/*
+ * Port A
+ */
+#define PADIR_ADDR	0xfffff400		/* Port A direction reg */
+#define PADATA_ADDR	0xfffff401		/* Port A data register */
+#define PAPUEN_ADDR	0xfffff402		/* Port A Pull-Up enable reg */
+
+#define PADIR		BYTE_REF(PADIR_ADDR)
+#define PADATA		BYTE_REF(PADATA_ADDR)
+#define PAPUEN		BYTE_REF(PAPUEN_ADDR)
+
+#define PA(x)		(1 << (x))
+
+/* 
+ * Port B
+ */
+#define PBDIR_ADDR	0xfffff408		/* Port B direction reg */
+#define PBDATA_ADDR	0xfffff409		/* Port B data register */
+#define PBPUEN_ADDR	0xfffff40a		/* Port B Pull-Up enable reg */
+#define PBSEL_ADDR	0xfffff40b		/* Port B Select Register */
+
+#define PBDIR		BYTE_REF(PBDIR_ADDR)
+#define PBDATA		BYTE_REF(PBDATA_ADDR)
+#define PBPUEN		BYTE_REF(PBPUEN_ADDR)
+#define PBSEL		BYTE_REF(PBSEL_ADDR)
+
+#define PB(x)		(1 << (x))
+
+#define PB_CSB0		0x01	/* Use CSB0      as PB[0] */
+#define PB_CSB1		0x02	/* Use CSB1      as PB[1] */
+#define PB_CSC0_RAS0	0x04    /* Use CSC0/RAS0 as PB[2] */	
+#define PB_CSC1_RAS1	0x08    /* Use CSC1/RAS1 as PB[3] */	
+#define PB_CSD0_CAS0	0x10    /* Use CSD0/CAS0 as PB[4] */	
+#define PB_CSD1_CAS1	0x20    /* Use CSD1/CAS1 as PB[5] */
+#define PB_TIN_TOUT	0x40	/* Use TIN/TOUT  as PB[6] */
+#define PB_PWMO		0x80	/* Use PWMO      as PB[7] */
+
+/* 
+ * Port C
+ */
+#define PCDIR_ADDR	0xfffff410		/* Port C direction reg */
+#define PCDATA_ADDR	0xfffff411		/* Port C data register */
+#define PCPDEN_ADDR	0xfffff412		/* Port C Pull-Down enb. reg */
+#define PCSEL_ADDR	0xfffff413		/* Port C Select Register */
+
+#define PCDIR		BYTE_REF(PCDIR_ADDR)
+#define PCDATA		BYTE_REF(PCDATA_ADDR)
+#define PCPDEN		BYTE_REF(PCPDEN_ADDR)
+#define PCSEL		BYTE_REF(PCSEL_ADDR)
+
+#define PC(x)		(1 << (x))
+
+#define PC_LD0		0x01	/* Use LD0  as PC[0] */
+#define PC_LD1		0x02	/* Use LD1  as PC[1] */
+#define PC_LD2		0x04	/* Use LD2  as PC[2] */
+#define PC_LD3		0x08	/* Use LD3  as PC[3] */
+#define PC_LFLM		0x10	/* Use LFLM as PC[4] */
+#define PC_LLP 		0x20	/* Use LLP  as PC[5] */
+#define PC_LCLK		0x40	/* Use LCLK as PC[6] */
+#define PC_LACD		0x80	/* Use LACD as PC[7] */
+
+/* 
+ * Port D
+ */
+#define PDDIR_ADDR	0xfffff418		/* Port D direction reg */
+#define PDDATA_ADDR	0xfffff419		/* Port D data register */
+#define PDPUEN_ADDR	0xfffff41a		/* Port D Pull-Up enable reg */
+#define PDSEL_ADDR	0xfffff41b		/* Port D Select Register */
+#define PDPOL_ADDR	0xfffff41c		/* Port D Polarity Register */
+#define PDIRQEN_ADDR	0xfffff41d		/* Port D IRQ enable register */
+#define PDKBEN_ADDR	0xfffff41e		/* Port D Keyboard Enable reg */
+#define	PDIQEG_ADDR	0xfffff41f		/* Port D IRQ Edge Register */
+
+#define PDDIR		BYTE_REF(PDDIR_ADDR)
+#define PDDATA		BYTE_REF(PDDATA_ADDR)
+#define PDPUEN		BYTE_REF(PDPUEN_ADDR)
+#define PDSEL		BYTE_REF(PDSEL_ADDR)
+#define	PDPOL		BYTE_REF(PDPOL_ADDR)
+#define PDIRQEN		BYTE_REF(PDIRQEN_ADDR)
+#define PDKBEN		BYTE_REF(PDKBEN_ADDR)
+#define PDIQEG		BYTE_REF(PDIQEG_ADDR)
+
+#define PD(x)		(1 << (x))
+
+#define PD_INT0		0x01	/* Use INT0 as PD[0] */
+#define PD_INT1		0x02	/* Use INT1 as PD[1] */
+#define PD_INT2		0x04	/* Use INT2 as PD[2] */
+#define PD_INT3		0x08	/* Use INT3 as PD[3] */
+#define PD_IRQ1		0x10	/* Use IRQ1 as PD[4] */
+#define PD_IRQ2		0x20	/* Use IRQ2 as PD[5] */
+#define PD_IRQ3		0x40	/* Use IRQ3 as PD[6] */
+#define PD_IRQ6		0x80	/* Use IRQ6 as PD[7] */
+
+/* 
+ * Port E
+ */
+#define PEDIR_ADDR	0xfffff420		/* Port E direction reg */
+#define PEDATA_ADDR	0xfffff421		/* Port E data register */
+#define PEPUEN_ADDR	0xfffff422		/* Port E Pull-Up enable reg */
+#define PESEL_ADDR	0xfffff423		/* Port E Select Register */
+
+#define PEDIR		BYTE_REF(PEDIR_ADDR)
+#define PEDATA		BYTE_REF(PEDATA_ADDR)
+#define PEPUEN		BYTE_REF(PEPUEN_ADDR)
+#define PESEL		BYTE_REF(PESEL_ADDR)
+
+#define PE(x)		(1 << (x))
+
+#define PE_SPMTXD	0x01	/* Use SPMTXD as PE[0] */
+#define PE_SPMRXD	0x02	/* Use SPMRXD as PE[1] */
+#define PE_SPMCLK	0x04	/* Use SPMCLK as PE[2] */
+#define PE_DWE		0x08	/* Use DWE    as PE[3] */
+#define PE_RXD		0x10	/* Use RXD    as PE[4] */
+#define PE_TXD		0x20	/* Use TXD    as PE[5] */
+#define PE_RTS		0x40	/* Use RTS    as PE[6] */
+#define PE_CTS		0x80	/* Use CTS    as PE[7] */
+
+/* 
+ * Port F
+ */
+#define PFDIR_ADDR	0xfffff428		/* Port F direction reg */
+#define PFDATA_ADDR	0xfffff429		/* Port F data register */
+#define PFPUEN_ADDR	0xfffff42a		/* Port F Pull-Up enable reg */
+#define PFSEL_ADDR	0xfffff42b		/* Port F Select Register */
+
+#define PFDIR		BYTE_REF(PFDIR_ADDR)
+#define PFDATA		BYTE_REF(PFDATA_ADDR)
+#define PFPUEN		BYTE_REF(PFPUEN_ADDR)
+#define PFSEL		BYTE_REF(PFSEL_ADDR)
+
+#define PF(x)		(1 << (x))
+
+#define PF_LCONTRAST	0x01	/* Use LCONTRAST as PF[0] */
+#define PF_IRQ5         0x02    /* Use IRQ5      as PF[1] */
+#define PF_CLKO         0x04    /* Use CLKO      as PF[2] */
+#define PF_A20          0x08    /* Use A20       as PF[3] */
+#define PF_A21          0x10    /* Use A21       as PF[4] */
+#define PF_A22          0x20    /* Use A22       as PF[5] */
+#define PF_A23          0x40    /* Use A23       as PF[6] */
+#define PF_CSA1		0x80    /* Use CSA1      as PF[7] */
+
+/* 
+ * Port G
+ */
+#define PGDIR_ADDR	0xfffff430		/* Port G direction reg */
+#define PGDATA_ADDR	0xfffff431		/* Port G data register */
+#define PGPUEN_ADDR	0xfffff432		/* Port G Pull-Up enable reg */
+#define PGSEL_ADDR	0xfffff433		/* Port G Select Register */
+
+#define PGDIR		BYTE_REF(PGDIR_ADDR)
+#define PGDATA		BYTE_REF(PGDATA_ADDR)
+#define PGPUEN		BYTE_REF(PGPUEN_ADDR)
+#define PGSEL		BYTE_REF(PGSEL_ADDR)
+
+#define PG(x)		(1 << (x))
+
+#define PG_BUSW_DTACK	0x01	/* Use BUSW/DTACK as PG[0] */
+#define PG_A0		0x02	/* Use A0         as PG[1] */
+#define PG_EMUIRQ	0x04	/* Use EMUIRQ     as PG[2] */
+#define PG_HIZ_P_D	0x08	/* Use HIZ/P/D    as PG[3] */
+#define PG_EMUCS        0x10	/* Use EMUCS      as PG[4] */
+#define PG_EMUBRK	0x20	/* Use EMUBRK     as PG[5] */
+
+/**********
+ *
+ * 0xFFFFF5xx -- Pulse-Width Modulator (PWM)
+ *
+ **********/
+
+/*
+ * PWM Control Register 
+ */
+#define PWMC_ADDR	0xfffff500
+#define PWMC		WORD_REF(PWMC_ADDR)
+
+#define PWMC_CLKSEL_MASK	0x0003	/* Clock Selection */
+#define PWMC_CLKSEL_SHIFT	0
+#define PWMC_REPEAT_MASK	0x000c	/* Sample Repeats */
+#define PWMC_REPEAT_SHIFT	2
+#define PWMC_EN			0x0010	/* Enable PWM */
+#define PMNC_FIFOAV		0x0020	/* FIFO Available */
+#define PWMC_IRQEN		0x0040	/* Interrupt Request Enable */
+#define PWMC_IRQ		0x0080	/* Interrupt Request (FIFO empty) */
+#define PWMC_PRESCALER_MASK	0x7f00	/* Incoming Clock prescaler */
+#define PWMC_PRESCALER_SHIFT	8
+#define PWMC_CLKSRC		0x8000	/* Clock Source Select */
+
+/* '328-compatible definitions */
+#define PWMC_PWMEN	PWMC_EN
+
+/*
+ * PWM Sample Register 
+ */
+#define PWMS_ADDR	0xfffff502
+#define PWMS		WORD_REF(PWMS_ADDR)
+
+/*
+ * PWM Period Register
+ */
+#define PWMP_ADDR	0xfffff504
+#define PWMP		BYTE_REF(PWMP_ADDR)
+
+/*
+ * PWM Counter Register
+ */
+#define PWMCNT_ADDR	0xfffff505
+#define PWMCNT		BYTE_REF(PWMCNT_ADDR)
+
+/**********
+ *
+ * 0xFFFFF6xx -- General-Purpose Timer
+ *
+ **********/
+
+/* 
+ * Timer Control register
+ */
+#define TCTL_ADDR	0xfffff600
+#define TCTL		WORD_REF(TCTL_ADDR)
+
+#define	TCTL_TEN		0x0001	/* Timer Enable  */
+#define TCTL_CLKSOURCE_MASK 	0x000e	/* Clock Source: */
+#define   TCTL_CLKSOURCE_STOP	   0x0000	/* Stop count (disabled)    */
+#define   TCTL_CLKSOURCE_SYSCLK	   0x0002	/* SYSCLK to prescaler      */
+#define   TCTL_CLKSOURCE_SYSCLK_16 0x0004	/* SYSCLK/16 to prescaler   */
+#define   TCTL_CLKSOURCE_TIN	   0x0006	/* TIN to prescaler         */
+#define   TCTL_CLKSOURCE_32KHZ	   0x0008	/* 32kHz clock to prescaler */
+#define TCTL_IRQEN		0x0010	/* IRQ Enable    */
+#define TCTL_OM			0x0020	/* Output Mode   */
+#define TCTL_CAP_MASK		0x00c0	/* Capture Edge: */
+#define	  TCTL_CAP_RE		0x0040		/* Capture on rizing edge   */
+#define   TCTL_CAP_FE		0x0080		/* Capture on falling edge  */
+#define TCTL_FRR		0x0010	/* Free-Run Mode */
+
+/* '328-compatible definitions */
+#define TCTL1_ADDR	TCTL_ADDR
+#define TCTL1		TCTL
+
+/*
+ * Timer Prescaler Register
+ */
+#define TPRER_ADDR	0xfffff602
+#define TPRER		WORD_REF(TPRER_ADDR)
+
+/* '328-compatible definitions */
+#define TPRER1_ADDR	TPRER_ADDR
+#define TPRER1		TPRER
+
+/*
+ * Timer Compare Register
+ */
+#define TCMP_ADDR	0xfffff604
+#define TCMP		WORD_REF(TCMP_ADDR)
+
+/* '328-compatible definitions */
+#define TCMP1_ADDR	TCMP_ADDR
+#define TCMP1		TCMP
+
+/*
+ * Timer Capture register
+ */
+#define TCR_ADDR	0xfffff606
+#define TCR		WORD_REF(TCR_ADDR)
+
+/* '328-compatible definitions */
+#define TCR1_ADDR	TCR_ADDR
+#define TCR1		TCR
+
+/*
+ * Timer Counter Register
+ */
+#define TCN_ADDR	0xfffff608
+#define TCN		WORD_REF(TCN_ADDR)
+
+/* '328-compatible definitions */
+#define TCN1_ADDR	TCN_ADDR
+#define TCN1		TCN
+
+/*
+ * Timer Status Register
+ */
+#define TSTAT_ADDR	0xfffff60a
+#define TSTAT		WORD_REF(TSTAT_ADDR)
+
+#define TSTAT_COMP	0x0001		/* Compare Event occurred */
+#define TSTAT_CAPT	0x0001		/* Capture Event occurred */
+
+/* '328-compatible definitions */
+#define TSTAT1_ADDR	TSTAT_ADDR
+#define TSTAT1		TSTAT
+
+/**********
+ *
+ * 0xFFFFF8xx -- Serial Periferial Interface Master (SPIM)
+ *
+ **********/
+
+/*
+ * SPIM Data Register
+ */
+#define SPIMDATA_ADDR	0xfffff800
+#define SPIMDATA	WORD_REF(SPIMDATA_ADDR)
+
+/*
+ * SPIM Control/Status Register
+ */
+#define SPIMCONT_ADDR	0xfffff802
+#define SPIMCONT	WORD_REF(SPIMCONT_ADDR)
+
+#define SPIMCONT_BIT_COUNT_MASK	 0x000f	/* Transfer Length in Bytes */
+#define SPIMCONT_BIT_COUNT_SHIFT 0
+#define SPIMCONT_POL		 0x0010	/* SPMCLK Signel Polarity */
+#define	SPIMCONT_PHA		 0x0020	/* Clock/Data phase relationship */
+#define SPIMCONT_IRQEN		 0x0040 /* IRQ Enable */
+#define SPIMCONT_IRQ		 0x0080	/* Interrupt Request */
+#define SPIMCONT_XCH		 0x0100	/* Exchange */
+#define SPIMCONT_ENABLE		 0x0200	/* Enable SPIM */
+#define SPIMCONT_DATA_RATE_MASK	 0xe000	/* SPIM Data Rate */
+#define SPIMCONT_DATA_RATE_SHIFT 13
+
+/* '328-compatible definitions */
+#define SPIMCONT_SPIMIRQ	SPIMCONT_IRQ
+#define SPIMCONT_SPIMEN		SPIMCONT_ENABLE
+
+/**********
+ *
+ * 0xFFFFF9xx -- UART
+ *
+ **********/
+
+/*
+ * UART Status/Control Register
+ */
+#define USTCNT_ADDR	0xfffff900
+#define USTCNT		WORD_REF(USTCNT_ADDR)
+
+#define USTCNT_TXAE	0x0001	/* Transmitter Available Interrupt Enable */
+#define USTCNT_TXHE	0x0002	/* Transmitter Half Empty Enable */
+#define USTCNT_TXEE	0x0004	/* Transmitter Empty Interrupt Enable */
+#define USTCNT_RXRE	0x0008	/* Receiver Ready Interrupt Enable */
+#define USTCNT_RXHE	0x0010	/* Receiver Half-Full Interrupt Enable */
+#define USTCNT_RXFE	0x0020	/* Receiver Full Interrupt Enable */
+#define USTCNT_CTSD	0x0040	/* CTS Delta Interrupt Enable */
+#define USTCNT_ODEN	0x0080	/* Old Data Interrupt Enable */
+#define USTCNT_8_7	0x0100	/* Eight or seven-bit transmission */
+#define USTCNT_STOP	0x0200	/* Stop bit transmission */
+#define USTCNT_ODD	0x0400	/* Odd Parity */
+#define	USTCNT_PEN	0x0800	/* Parity Enable */
+#define USTCNT_CLKM	0x1000	/* Clock Mode Select */
+#define	USTCNT_TXEN	0x2000	/* Transmitter Enable */
+#define USTCNT_RXEN	0x4000	/* Receiver Enable */
+#define USTCNT_UEN	0x8000	/* UART Enable */
+
+/* '328-compatible definitions */
+#define USTCNT_TXAVAILEN	USTCNT_TXAE
+#define USTCNT_TXHALFEN		USTCNT_TXHE
+#define USTCNT_TXEMPTYEN	USTCNT_TXEE
+#define USTCNT_RXREADYEN	USTCNT_RXRE
+#define USTCNT_RXHALFEN		USTCNT_RXHE
+#define USTCNT_RXFULLEN		USTCNT_RXFE
+#define USTCNT_CTSDELTAEN	USTCNT_CTSD
+#define USTCNT_ODD_EVEN		USTCNT_ODD
+#define USTCNT_PARITYEN		USTCNT_PEN
+#define USTCNT_CLKMODE		USTCNT_CLKM
+#define USTCNT_UARTEN		USTCNT_UEN
+
+/*
+ * UART Baud Control Register
+ */
+#define UBAUD_ADDR	0xfffff902
+#define UBAUD		WORD_REF(UBAUD_ADDR)
+
+#define UBAUD_PRESCALER_MASK	0x003f	/* Actual divisor is 65 - PRESCALER */
+#define UBAUD_PRESCALER_SHIFT	0
+#define UBAUD_DIVIDE_MASK	0x0700	/* Baud Rate freq. divizor */
+#define UBAUD_DIVIDE_SHIFT	8
+#define UBAUD_BAUD_SRC		0x0800	/* Baud Rate Source */
+#define UBAUD_UCLKDIR		0x2000	/* UCLK Direction */
+
+/*
+ * UART Receiver Register 
+ */
+#define URX_ADDR	0xfffff904
+#define URX		WORD_REF(URX_ADDR)
+
+#define URX_RXDATA_ADDR	0xfffff905
+#define URX_RXDATA	BYTE_REF(URX_RXDATA_ADDR)
+
+#define URX_RXDATA_MASK	 0x00ff	/* Received data */
+#define URX_RXDATA_SHIFT 0
+#define URX_PARITY_ERROR 0x0100	/* Parity Error */
+#define URX_BREAK	 0x0200	/* Break Detected */
+#define URX_FRAME_ERROR	 0x0400	/* Framing Error */
+#define URX_OVRUN	 0x0800	/* Serial Overrun */
+#define URX_OLD_DATA	 0x1000	/* Old data in FIFO */
+#define URX_DATA_READY	 0x2000	/* Data Ready (FIFO not empty) */
+#define URX_FIFO_HALF	 0x4000 /* FIFO is Half-Full */
+#define URX_FIFO_FULL	 0x8000	/* FIFO is Full */
+
+/*
+ * UART Transmitter Register 
+ */
+#define UTX_ADDR	0xfffff906
+#define UTX		WORD_REF(UTX_ADDR)
+
+#define UTX_TXDATA_ADDR	0xfffff907
+#define UTX_TXDATA	BYTE_REF(UTX_TXDATA_ADDR)
+
+#define UTX_TXDATA_MASK	 0x00ff	/* Data to be transmitted */
+#define UTX_TXDATA_SHIFT 0
+#define UTX_CTS_DELTA	 0x0100	/* CTS changed */
+#define UTX_CTS_STAT	 0x0200	/* CTS State */
+#define	UTX_BUSY	 0x0400	/* FIFO is busy, sending a character */
+#define	UTX_NOCTS	 0x0800	/* Ignore CTS */
+#define UTX_SEND_BREAK	 0x1000	/* Send a BREAK */
+#define UTX_TX_AVAIL	 0x2000	/* Transmit FIFO has a slot available */
+#define UTX_FIFO_HALF	 0x4000	/* Transmit FIFO is half empty */
+#define UTX_FIFO_EMPTY	 0x8000	/* Transmit FIFO is empty */
+
+/* '328-compatible definitions */
+#define UTX_CTS_STATUS	UTX_CTS_STAT
+#define UTX_IGNORE_CTS	UTX_NOCTS
+
+/*
+ * UART Miscellaneous Register 
+ */
+#define UMISC_ADDR	0xfffff908
+#define UMISC		WORD_REF(UMISC_ADDR)
+
+#define UMISC_TX_POL	 0x0004	/* Transmit Polarity */
+#define UMISC_RX_POL	 0x0008	/* Receive Polarity */
+#define UMISC_IRDA_LOOP	 0x0010	/* IrDA Loopback Enable */
+#define UMISC_IRDA_EN	 0x0020	/* Infra-Red Enable */
+#define UMISC_RTS	 0x0040	/* Set RTS status */
+#define UMISC_RTSCONT	 0x0080	/* Choose RTS control */
+#define UMISC_IR_TEST	 0x0400	/* IRDA Test Enable */
+#define UMISC_BAUD_RESET 0x0800	/* Reset Baud Rate Generation Counters */
+#define UMISC_LOOP	 0x1000	/* Serial Loopback Enable */
+#define UMISC_FORCE_PERR 0x2000	/* Force Parity Error */
+#define UMISC_CLKSRC	 0x4000	/* Clock Source */
+#define UMISC_BAUD_TEST	 0x8000	/* Enable Baud Test Mode */
+
+/* 
+ * UART Non-integer Prescaler Register
+ */
+#define NIPR_ADDR	0xfffff90a
+#define NIPR		WORD_REF(NIPR_ADDR)
+
+#define NIPR_STEP_VALUE_MASK	0x00ff	/* NI prescaler step value */
+#define NIPR_STEP_VALUE_SHIFT	0
+#define NIPR_SELECT_MASK	0x0700	/* Tap Selection */
+#define NIPR_SELECT_SHIFT	8
+#define NIPR_PRE_SEL		0x8000	/* Non-integer prescaler select */
+
+
+/* generalization of uart control registers to support multiple ports: */
+typedef volatile struct {
+  volatile unsigned short int ustcnt;
+  volatile unsigned short int ubaud;
+  union {
+    volatile unsigned short int w;
+    struct {
+      volatile unsigned char status;
+      volatile unsigned char rxdata;
+    } b;
+  } urx;
+  union {
+    volatile unsigned short int w;
+    struct {
+      volatile unsigned char status;
+      volatile unsigned char txdata;
+    } b;
+  } utx;
+  volatile unsigned short int umisc;
+  volatile unsigned short int nipr;
+  volatile unsigned short int pad1;
+  volatile unsigned short int pad2;
+} __attribute__((packed)) m68328_uart;
+
+
+/**********
+ *
+ * 0xFFFFFAxx -- LCD Controller
+ *
+ **********/
+
+/*
+ * LCD Screen Starting Address Register 
+ */
+#define LSSA_ADDR	0xfffffa00
+#define LSSA		LONG_REF(LSSA_ADDR)
+
+#define LSSA_SSA_MASK	0x1ffffffe	/* Bits 0 and 29-31 are reserved */
+
+/*
+ * LCD Virtual Page Width Register 
+ */
+#define LVPW_ADDR	0xfffffa05
+#define LVPW		BYTE_REF(LVPW_ADDR)
+
+/*
+ * LCD Screen Width Register (not compatible with '328 !!!) 
+ */
+#define LXMAX_ADDR	0xfffffa08
+#define LXMAX		WORD_REF(LXMAX_ADDR)
+
+#define LXMAX_XM_MASK	0x02f0		/* Bits 0-3 and 10-15 are reserved */
+
+/*
+ * LCD Screen Height Register
+ */
+#define LYMAX_ADDR	0xfffffa0a
+#define LYMAX		WORD_REF(LYMAX_ADDR)
+
+#define LYMAX_YM_MASK	0x01ff		/* Bits 9-15 are reserved */
+
+/*
+ * LCD Cursor X Position Register
+ */
+#define LCXP_ADDR	0xfffffa18
+#define LCXP		WORD_REF(LCXP_ADDR)
+
+#define LCXP_CC_MASK	0xc000		/* Cursor Control */
+#define   LCXP_CC_TRAMSPARENT	0x0000
+#define   LCXP_CC_BLACK		0x4000
+#define   LCXP_CC_REVERSED	0x8000
+#define   LCXP_CC_WHITE		0xc000
+#define LCXP_CXP_MASK	0x02ff		/* Cursor X position */
+
+/*
+ * LCD Cursor Y Position Register
+ */
+#define LCYP_ADDR	0xfffffa1a
+#define LCYP		WORD_REF(LCYP_ADDR)
+
+#define LCYP_CYP_MASK	0x01ff		/* Cursor Y Position */
+
+/*
+ * LCD Cursor Width and Heigth Register
+ */
+#define LCWCH_ADDR	0xfffffa1c
+#define LCWCH		WORD_REF(LCWCH_ADDR)
+
+#define LCWCH_CH_MASK	0x001f		/* Cursor Height */
+#define LCWCH_CH_SHIFT	0
+#define LCWCH_CW_MASK	0x1f00		/* Cursor Width */
+#define LCWCH_CW_SHIFT	8
+
+/*
+ * LCD Blink Control Register
+ */
+#define LBLKC_ADDR	0xfffffa1f
+#define LBLKC		BYTE_REF(LBLKC_ADDR)
+
+#define LBLKC_BD_MASK	0x7f	/* Blink Divisor */
+#define LBLKC_BD_SHIFT	0
+#define LBLKC_BKEN	0x80	/* Blink Enabled */
+
+/*
+ * LCD Panel Interface Configuration Register 
+ */
+#define LPICF_ADDR	0xfffffa20
+#define LPICF		BYTE_REF(LPICF_ADDR)
+
+#define LPICF_GS_MASK	 0x03	 /* Gray-Scale Mode */
+#define	  LPICF_GS_BW	   0x00
+#define   LPICF_GS_GRAY_4  0x01
+#define   LPICF_GS_GRAY_16 0x02
+#define LPICF_PBSIZ_MASK 0x0c	/* Panel Bus Width */
+#define   LPICF_PBSIZ_1	   0x00
+#define   LPICF_PBSIZ_2    0x04
+#define   LPICF_PBSIZ_4    0x08
+
+/*
+ * LCD Polarity Configuration Register 
+ */
+#define LPOLCF_ADDR	0xfffffa21
+#define LPOLCF		BYTE_REF(LPOLCF_ADDR)
+
+#define LPOLCF_PIXPOL	0x01	/* Pixel Polarity */
+#define LPOLCF_LPPOL	0x02	/* Line Pulse Polarity */
+#define LPOLCF_FLMPOL	0x04	/* Frame Marker Polarity */
+#define LPOLCF_LCKPOL	0x08	/* LCD Shift Lock Polarity */
+
+/*
+ * LACD (LCD Alternate Crystal Direction) Rate Control Register
+ */
+#define LACDRC_ADDR	0xfffffa23
+#define LACDRC		BYTE_REF(LACDRC_ADDR)
+
+#define LACDRC_ACDSLT	 0x80	/* Signal Source Select */
+#define LACDRC_ACD_MASK	 0x0f	/* Alternate Crystal Direction Control */
+#define LACDRC_ACD_SHIFT 0
+
+/*
+ * LCD Pixel Clock Divider Register
+ */
+#define LPXCD_ADDR	0xfffffa25
+#define LPXCD		BYTE_REF(LPXCD_ADDR)
+
+#define	LPXCD_PCD_MASK	0x3f 	/* Pixel Clock Divider */
+#define LPXCD_PCD_SHIFT	0
+
+/*
+ * LCD Clocking Control Register
+ */
+#define LCKCON_ADDR	0xfffffa27
+#define LCKCON		BYTE_REF(LCKCON_ADDR)
+
+#define LCKCON_DWS_MASK	 0x0f	/* Display Wait-State */
+#define LCKCON_DWS_SHIFT 0
+#define LCKCON_DWIDTH	 0x40	/* Display Memory Width  */
+#define LCKCON_LCDON	 0x80	/* Enable LCD Controller */
+
+/* '328-compatible definitions */
+#define LCKCON_DW_MASK  LCKCON_DWS_MASK
+#define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT
+ 
+/*
+ * LCD Refresh Rate Adjustment Register 
+ */
+#define LRRA_ADDR	0xfffffa29
+#define LRRA		BYTE_REF(LRRA_ADDR)
+
+/*
+ * LCD Panning Offset Register
+ */
+#define LPOSR_ADDR	0xfffffa2d
+#define LPOSR		BYTE_REF(LPOSR_ADDR)
+
+#define LPOSR_POS_MASK	0x0f	/* Pixel Offset Code */
+#define LPOSR_POS_SHIFT	0
+
+/*
+ * LCD Frame Rate Control Modulation Register
+ */
+#define LFRCM_ADDR	0xfffffa31
+#define LFRCM		BYTE_REF(LFRCM_ADDR)
+
+#define LFRCM_YMOD_MASK	 0x0f	/* Vertical Modulation */
+#define LFRCM_YMOD_SHIFT 0
+#define LFRCM_XMOD_MASK	 0xf0	/* Horizontal Modulation */
+#define LFRCM_XMOD_SHIFT 4
+
+/*
+ * LCD Gray Palette Mapping Register
+ */
+#define LGPMR_ADDR	0xfffffa33
+#define LGPMR		BYTE_REF(LGPMR_ADDR)
+
+#define LGPMR_G1_MASK	0x0f
+#define LGPMR_G1_SHIFT	0
+#define LGPMR_G2_MASK	0xf0
+#define LGPMR_G2_SHIFT	4
+
+/* 
+ * PWM Contrast Control Register
+ */
+#define PWMR_ADDR	0xfffffa36
+#define PWMR		WORD_REF(PWMR_ADDR)
+
+#define PWMR_PW_MASK	0x00ff	/* Pulse Width */
+#define PWMR_PW_SHIFT	0
+#define PWMR_CCPEN	0x0100	/* Contrast Control Enable */
+#define PWMR_SRC_MASK	0x0600	/* Input Clock Source */
+#define   PWMR_SRC_LINE	  0x0000	/* Line Pulse  */
+#define   PWMR_SRC_PIXEL  0x0200	/* Pixel Clock */
+#define   PWMR_SRC_LCD    0x4000	/* LCD clock   */
+
+/**********
+ *
+ * 0xFFFFFBxx -- Real-Time Clock (RTC)
+ *
+ **********/
+
+/*
+ * RTC Hours Minutes and Seconds Register
+ */
+#define RTCTIME_ADDR	0xfffffb00
+#define RTCTIME		LONG_REF(RTCTIME_ADDR)
+
+#define RTCTIME_SECONDS_MASK	0x0000003f	/* Seconds */
+#define RTCTIME_SECONDS_SHIFT	0
+#define RTCTIME_MINUTES_MASK	0x003f0000	/* Minutes */
+#define RTCTIME_MINUTES_SHIFT	16
+#define RTCTIME_HOURS_MASK	0x1f000000	/* Hours */
+#define RTCTIME_HOURS_SHIFT	24
+
+/*
+ *  RTC Alarm Register 
+ */
+#define RTCALRM_ADDR    0xfffffb04
+#define RTCALRM         LONG_REF(RTCALRM_ADDR)
+
+#define RTCALRM_SECONDS_MASK    0x0000003f      /* Seconds */
+#define RTCALRM_SECONDS_SHIFT   0
+#define RTCALRM_MINUTES_MASK    0x003f0000      /* Minutes */
+#define RTCALRM_MINUTES_SHIFT   16
+#define RTCALRM_HOURS_MASK      0x1f000000      /* Hours */
+#define RTCALRM_HOURS_SHIFT     24
+
+/*
+ * Watchdog Timer Register 
+ */
+#define WATCHDOG_ADDR	0xfffffb0a
+#define WATCHDOG	WORD_REF(WATCHDOG_ADDR)
+
+#define WATCHDOG_EN	0x0001	/* Watchdog Enabled */
+#define WATCHDOG_ISEL	0x0002	/* Select the watchdog interrupt */
+#define WATCHDOG_INTF	0x0080	/* Watchdog interrupt occcured */
+#define WATCHDOG_CNT_MASK  0x0300	/* Watchdog Counter */
+#define WATCHDOG_CNT_SHIFT 8
+
+/*
+ * RTC Control Register
+ */
+#define RTCCTL_ADDR	0xfffffb0c
+#define RTCCTL		WORD_REF(RTCCTL_ADDR)
+
+#define RTCCTL_XTL	0x0020	/* Crystal Selection */
+#define RTCCTL_EN	0x0080	/* RTC Enable */
+
+/* '328-compatible definitions */
+#define RTCCTL_384	RTCCTL_XTL
+#define RTCCTL_ENABLE	RTCCTL_EN
+
+/*
+ * RTC Interrupt Status Register 
+ */
+#define RTCISR_ADDR	0xfffffb0e
+#define RTCISR		WORD_REF(RTCISR_ADDR)
+
+#define RTCISR_SW	0x0001	/* Stopwatch timed out */
+#define RTCISR_MIN	0x0002	/* 1-minute interrupt has occurred */
+#define RTCISR_ALM	0x0004	/* Alarm interrupt has occurred */
+#define RTCISR_DAY	0x0008	/* 24-hour rollover interrupt has occurred */
+#define RTCISR_1HZ	0x0010	/* 1Hz interrupt has occurred */
+#define RTCISR_HR	0x0020	/* 1-hour interrupt has occurred */
+#define RTCISR_SAM0	0x0100	/*   4Hz /   4.6875Hz interrupt has occurred */ 
+#define RTCISR_SAM1	0x0200	/*   8Hz /   9.3750Hz interrupt has occurred */ 
+#define RTCISR_SAM2	0x0400	/*  16Hz /  18.7500Hz interrupt has occurred */ 
+#define RTCISR_SAM3	0x0800	/*  32Hz /  37.5000Hz interrupt has occurred */ 
+#define RTCISR_SAM4	0x1000	/*  64Hz /  75.0000Hz interrupt has occurred */ 
+#define RTCISR_SAM5	0x2000	/* 128Hz / 150.0000Hz interrupt has occurred */ 
+#define RTCISR_SAM6	0x4000	/* 256Hz / 300.0000Hz interrupt has occurred */ 
+#define RTCISR_SAM7	0x8000	/* 512Hz / 600.0000Hz interrupt has occurred */ 
+
+/*
+ * RTC Interrupt Enable Register
+ */
+#define RTCIENR_ADDR	0xfffffb10
+#define RTCIENR		WORD_REF(RTCIENR_ADDR)
+
+#define RTCIENR_SW	0x0001	/* Stopwatch interrupt enable */
+#define RTCIENR_MIN	0x0002	/* 1-minute interrupt enable */
+#define RTCIENR_ALM	0x0004	/* Alarm interrupt enable */
+#define RTCIENR_DAY	0x0008	/* 24-hour rollover interrupt enable */
+#define RTCIENR_1HZ	0x0010	/* 1Hz interrupt enable */
+#define RTCIENR_HR	0x0020	/* 1-hour interrupt enable */
+#define RTCIENR_SAM0	0x0100	/*   4Hz /   4.6875Hz interrupt enable */ 
+#define RTCIENR_SAM1	0x0200	/*   8Hz /   9.3750Hz interrupt enable */ 
+#define RTCIENR_SAM2	0x0400	/*  16Hz /  18.7500Hz interrupt enable */ 
+#define RTCIENR_SAM3	0x0800	/*  32Hz /  37.5000Hz interrupt enable */ 
+#define RTCIENR_SAM4	0x1000	/*  64Hz /  75.0000Hz interrupt enable */ 
+#define RTCIENR_SAM5	0x2000	/* 128Hz / 150.0000Hz interrupt enable */ 
+#define RTCIENR_SAM6	0x4000	/* 256Hz / 300.0000Hz interrupt enable */ 
+#define RTCIENR_SAM7	0x8000	/* 512Hz / 600.0000Hz interrupt enable */ 
+
+/* 
+ * Stopwatch Minutes Register
+ */
+#define STPWCH_ADDR	0xfffffb12
+#define STPWCH		WORD_REF(STPWCH)
+
+#define STPWCH_CNT_MASK	 0x003f	/* Stopwatch countdown value */
+#define SPTWCH_CNT_SHIFT 0
+
+/*
+ * RTC Day Count Register 
+ */
+#define DAYR_ADDR	0xfffffb1a
+#define DAYR		WORD_REF(DAYR_ADDR)
+
+#define DAYR_DAYS_MASK	0x1ff	/* Day Setting */
+#define DAYR_DAYS_SHIFT 0
+
+/*
+ * RTC Day Alarm Register 
+ */
+#define DAYALARM_ADDR	0xfffffb1c
+#define DAYALARM	WORD_REF(DAYALARM_ADDR)
+
+#define DAYALARM_DAYSAL_MASK	0x01ff	/* Day Setting of the Alarm */
+#define DAYALARM_DAYSAL_SHIFT 	0
+
+/**********
+ *
+ * 0xFFFFFCxx -- DRAM Controller
+ *
+ **********/
+
+/*
+ * DRAM Memory Configuration Register 
+ */
+#define DRAMMC_ADDR	0xfffffc00
+#define DRAMMC		WORD_REF(DRAMMC_ADDR)
+
+#define DRAMMC_ROW12_MASK	0xc000	/* Row address bit for MD12 */
+#define   DRAMMC_ROW12_PA10	0x0000
+#define   DRAMMC_ROW12_PA21	0x4000	
+#define   DRAMMC_ROW12_PA23	0x8000
+#define	DRAMMC_ROW0_MASK	0x3000	/* Row address bit for MD0 */
+#define	  DRAMMC_ROW0_PA11	0x0000
+#define   DRAMMC_ROW0_PA22	0x1000
+#define   DRAMMC_ROW0_PA23	0x2000
+#define DRAMMC_ROW11		0x0800	/* Row address bit for MD11 PA20/PA22 */
+#define DRAMMC_ROW10		0x0400	/* Row address bit for MD10 PA19/PA21 */
+#define	DRAMMC_ROW9		0x0200	/* Row address bit for MD9  PA9/PA19  */
+#define DRAMMC_ROW8		0x0100	/* Row address bit for MD8  PA10/PA20 */
+#define DRAMMC_COL10		0x0080	/* Col address bit for MD10 PA11/PA0  */
+#define DRAMMC_COL9		0x0040	/* Col address bit for MD9  PA10/PA0  */
+#define DRAMMC_COL8		0x0020	/* Col address bit for MD8  PA9/PA0   */
+#define DRAMMC_REF_MASK		0x001f	/* Reresh Cycle */
+#define DRAMMC_REF_SHIFT	0
+
+/*
+ * DRAM Control Register
+ */
+#define DRAMC_ADDR	0xfffffc02
+#define DRAMC		WORD_REF(DRAMC_ADDR)
+
+#define DRAMC_DWE	   0x0001	/* DRAM Write Enable */
+#define DRAMC_RST	   0x0002	/* Reset Burst Refresh Enable */
+#define DRAMC_LPR	   0x0004	/* Low-Power Refresh Enable */
+#define DRAMC_SLW	   0x0008	/* Slow RAM */
+#define DRAMC_LSP	   0x0010	/* Light Sleep */
+#define DRAMC_MSW	   0x0020	/* Slow Multiplexing */
+#define DRAMC_WS_MASK	   0x00c0	/* Wait-states */
+#define DRAMC_WS_SHIFT	   6
+#define DRAMC_PGSZ_MASK    0x0300	/* Page Size for fast page mode */
+#define DRAMC_PGSZ_SHIFT   8
+#define   DRAMC_PGSZ_256K  0x0000	
+#define   DRAMC_PGSZ_512K  0x0100
+#define   DRAMC_PGSZ_1024K 0x0200
+#define	  DRAMC_PGSZ_2048K 0x0300
+#define DRAMC_EDO	   0x0400	/* EDO DRAM */
+#define DRAMC_CLK	   0x0800	/* Refresh Timer Clock source select */
+#define DRAMC_BC_MASK	   0x3000	/* Page Access Clock Cycle (FP mode) */
+#define DRAMC_BC_SHIFT	   12
+#define DRAMC_RM	   0x4000	/* Refresh Mode */
+#define DRAMC_EN	   0x8000	/* DRAM Controller enable */
+
+
+/**********
+ *
+ * 0xFFFFFDxx -- In-Circuit Emulation (ICE)
+ *
+ **********/
+
+/*
+ * ICE Module Address Compare Register
+ */
+#define ICEMACR_ADDR	0xfffffd00
+#define ICEMACR		LONG_REF(ICEMACR_ADDR)
+
+/*
+ * ICE Module Address Mask Register
+ */
+#define ICEMAMR_ADDR	0xfffffd04
+#define ICEMAMR		LONG_REF(ICEMAMR_ADDR)
+
+/*
+ * ICE Module Control Compare Register
+ */
+#define ICEMCCR_ADDR	0xfffffd08
+#define ICEMCCR		WORD_REF(ICEMCCR_ADDR)
+
+#define ICEMCCR_PD	0x0001	/* Program/Data Cycle Selection */
+#define ICEMCCR_RW	0x0002	/* Read/Write Cycle Selection */
+
+/*
+ * ICE Module Control Mask Register
+ */
+#define ICEMCMR_ADDR	0xfffffd0a
+#define ICEMCMR		WORD_REF(ICEMCMR_ADDR)
+
+#define ICEMCMR_PDM	0x0001	/* Program/Data Cycle Mask */
+#define ICEMCMR_RWM	0x0002	/* Read/Write Cycle Mask */
+
+/*
+ * ICE Module Control Register 
+ */
+#define ICEMCR_ADDR	0xfffffd0c
+#define ICEMCR		WORD_REF(ICEMCR_ADDR)
+
+#define ICEMCR_CEN	0x0001	/* Compare Enable */
+#define ICEMCR_PBEN	0x0002	/* Program Break Enable */
+#define ICEMCR_SB	0x0004	/* Single Breakpoint */
+#define ICEMCR_HMDIS	0x0008	/* HardMap disable */
+#define ICEMCR_BBIEN	0x0010	/* Bus Break Interrupt Enable */
+
+/*
+ * ICE Module Status Register 
+ */
+#define ICEMSR_ADDR	0xfffffd0e
+#define ICEMSR		WORD_REF(ICEMSR_ADDR)
+
+#define ICEMSR_EMUEN	0x0001	/* Emulation Enable */
+#define ICEMSR_BRKIRQ	0x0002	/* A-Line Vector Fetch Detected */
+#define ICEMSR_BBIRQ	0x0004	/* Bus Break Interrupt Detected */
+#define ICEMSR_EMIRQ	0x0008	/* EMUIRQ Falling Edge Detected */
+
+#endif /* _MC68EZ328_H_ */