MIPS: Alchemy: Fix up PM code on Au1550/Au1200

Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).

Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

1 files changed, 151 insertions, 115 deletions

diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c
index 997dd56bcc5..f08312b10d0 100644
--- a/arch/mips/alchemy/common/power.c
+++ b/arch/mips/alchemy/common/power.c
@@ -35,7 +35,6 @@
 #include <linux/jiffies.h>
 
 #include <asm/uaccess.h>
-#include <asm/cacheflush.h>
 #include <asm/mach-au1x00/au1000.h>
 
 #ifdef CONFIG_PM
@@ -47,8 +46,6 @@
 #define DPRINTK(fmt, args...)
 #endif
 
-static void au1000_calibrate_delay(void);
-
 extern unsigned long save_local_and_disable(int controller);
 extern void restore_local_and_enable(int controller, unsigned long mask);
 
@@ -64,17 +61,15 @@ static DEFINE_SPINLOCK(pm_lock);
  * We only have to save/restore registers that aren't otherwise
  * done as part of a driver pm_* function.
  */
-static unsigned int	sleep_aux_pll_cntrl;
-static unsigned int	sleep_cpu_pll_cntrl;
-static unsigned int	sleep_pin_function;
-static unsigned int	sleep_uart0_inten;
-static unsigned int	sleep_uart0_fifoctl;
-static unsigned int	sleep_uart0_linectl;
-static unsigned int	sleep_uart0_clkdiv;
-static unsigned int	sleep_uart0_enable;
-static unsigned int	sleep_usbhost_enable;
-static unsigned int	sleep_usbdev_enable;
-static unsigned int	sleep_static_memctlr[4][3];
+static unsigned int sleep_uart0_inten;
+static unsigned int sleep_uart0_fifoctl;
+static unsigned int sleep_uart0_linectl;
+static unsigned int sleep_uart0_clkdiv;
+static unsigned int sleep_uart0_enable;
+static unsigned int sleep_usb[2];
+static unsigned int sleep_sys_clocks[5];
+static unsigned int sleep_sys_pinfunc;
+static unsigned int sleep_static_memctlr[4][3];
 
 /*
  * Define this to cause the value you write to /proc/sys/pm/sleep to
@@ -108,31 +103,45 @@ static void save_core_regs(void)
 	sleep_uart0_linectl = au_readl(UART0_ADDR + UART_LCR);
 	sleep_uart0_clkdiv = au_readl(UART0_ADDR + UART_CLK);
 	sleep_uart0_enable = au_readl(UART0_ADDR + UART_MOD_CNTRL);
+	au_sync();
 
+#ifndef CONFIG_SOC_AU1200
 	/* Shutdown USB host/device. */
-	sleep_usbhost_enable = au_readl(USB_HOST_CONFIG);
+	sleep_usb[0] = au_readl(USB_HOST_CONFIG);
 
 	/* There appears to be some undocumented reset register.... */
-	au_writel(0, 0xb0100004); au_sync();
-	au_writel(0, USB_HOST_CONFIG); au_sync();
+	au_writel(0, 0xb0100004);
+	au_sync();
+	au_writel(0, USB_HOST_CONFIG);
+	au_sync();
+
+	sleep_usb[1] = au_readl(USBD_ENABLE);
+	au_writel(0, USBD_ENABLE);
+	au_sync();
+
+#else	/* AU1200 */
 
-	sleep_usbdev_enable = au_readl(USBD_ENABLE);
-	au_writel(0, USBD_ENABLE); au_sync();
+	/* enable access to OTG mmio so we can save OTG CAP/MUX.
+	 * FIXME: write an OTG driver and move this stuff there!
+	 */
+	au_writel(au_readl(USB_MSR_BASE + 4) | (1 << 6), USB_MSR_BASE + 4);
+	au_sync();
+	sleep_usb[0] = au_readl(0xb4020020);	/* OTG_CAP */
+	sleep_usb[1] = au_readl(0xb4020024);	/* OTG_MUX */
+#endif
 
 	/* Save interrupt controller state. */
 	save_au1xxx_intctl();
 
 	/* Clocks and PLLs. */
-	sleep_aux_pll_cntrl = au_readl(SYS_AUXPLL);
+	sleep_sys_clocks[0] = au_readl(SYS_FREQCTRL0);
+	sleep_sys_clocks[1] = au_readl(SYS_FREQCTRL1);
+	sleep_sys_clocks[2] = au_readl(SYS_CLKSRC);
+	sleep_sys_clocks[3] = au_readl(SYS_CPUPLL);
+	sleep_sys_clocks[4] = au_readl(SYS_AUXPLL);
 
-	/*
-	 * We don't really need to do this one, but unless we
-	 * write it again it won't have a valid value if we
-	 * happen to read it.
-	 */
-	sleep_cpu_pll_cntrl = au_readl(SYS_CPUPLL);
-
-	sleep_pin_function = au_readl(SYS_PINFUNC);
+	/* pin mux config */
+	sleep_sys_pinfunc = au_readl(SYS_PINFUNC);
 
 	/* Save the static memory controller configuration. */
 	sleep_static_memctlr[0][0] = au_readl(MEM_STCFG0);
@@ -151,12 +160,37 @@ static void save_core_regs(void)
 
 static void restore_core_regs(void)
 {
-	extern void restore_au1xxx_intctl(void);
-	extern void wakeup_counter0_adjust(void);
+	/* restore clock configuration.  Writing CPUPLL last will
+	 * stall a bit and stabilize other clocks (unless this is
+	 * one of those Au1000 with a write-only PLL, where we dont
+	 * have a valid value)
+	 */
+	au_writel(sleep_sys_clocks[0], SYS_FREQCTRL0);
+	au_writel(sleep_sys_clocks[1], SYS_FREQCTRL1);
+	au_writel(sleep_sys_clocks[2], SYS_CLKSRC);
+	au_writel(sleep_sys_clocks[4], SYS_AUXPLL);
+	if (!au1xxx_cpu_has_pll_wo())
+		au_writel(sleep_sys_clocks[3], SYS_CPUPLL);
+	au_sync();
+
+	au_writel(sleep_sys_pinfunc, SYS_PINFUNC);
+	au_sync();
+
+#ifndef CONFIG_SOC_AU1200
+	au_writel(sleep_usb[0], USB_HOST_CONFIG);
+	au_writel(sleep_usb[1], USBD_ENABLE);
+	au_sync();
+#else
+	/* enable accces to OTG memory */
+	au_writel(au_readl(USB_MSR_BASE + 4) | (1 << 6), USB_MSR_BASE + 4);
+	au_sync();
 
-	au_writel(sleep_aux_pll_cntrl, SYS_AUXPLL); au_sync();
-	au_writel(sleep_cpu_pll_cntrl, SYS_CPUPLL); au_sync();
-	au_writel(sleep_pin_function, SYS_PINFUNC); au_sync();
+	/* restore OTG caps and port mux. */
+	au_writel(sleep_usb[0], 0xb4020020 + 0);	/* OTG_CAP */
+	au_sync();
+	au_writel(sleep_usb[1], 0xb4020020 + 4);	/* OTG_MUX */
+	au_sync();
+#endif
 
 	/* Restore the static memory controller configuration. */
 	au_writel(sleep_static_memctlr[0][0], MEM_STCFG0);
@@ -196,16 +230,45 @@ void wakeup_from_suspend(void)
 	suspend_mode = 0;
 }
 
-int au_sleep(void)
+void au_sleep(void)
+{
+	save_core_regs();
+	au1xxx_save_and_sleep();
+	restore_core_regs();
+}
+
+static int pm_do_sleep(ctl_table *ctl, int write, struct file *file,
+		       void __user *buffer, size_t *len, loff_t *ppos)
 {
 	unsigned long wakeup, flags;
-	extern void save_and_sleep(void);
+	int ret;
+#ifdef SLEEP_TEST_TIMEOUT
+#define TMPBUFLEN2 16
+	char buf[TMPBUFLEN2], *p;
+#endif
 
 	spin_lock_irqsave(&pm_lock, flags);
 
-	save_core_regs();
+	if (!write) {
+		*len = 0;
+		ret = 0;
+		goto out_unlock;
+	};
 
-	flush_cache_all();
+#ifdef SLEEP_TEST_TIMEOUT
+	if (*len > TMPBUFLEN2 - 1) {
+		ret = -EFAULT;
+		goto out_unlock;
+	}
+	if (copy_from_user(buf, buffer, *len)) {
+		return -EFAULT;
+		goto out_unlock;
+	}
+	buf[*len] = 0;
+	p = buf;
+	sleep_ticks = simple_strtoul(p, &p, 0);
+	wakeup_counter0_set(sleep_ticks);
+#endif
 
 	/**
 	 ** The code below is all system dependent and we should probably
@@ -223,9 +286,6 @@ int au_sleep(void)
 	wakeup |= 1 << 6;	/* turn on  GPIO  6 wakeup */
 #else
 	/* For testing, allow match20 to wake us up. */
-#ifdef SLEEP_TEST_TIMEOUT
-	wakeup_counter0_set(sleep_ticks);
-#endif
 	wakeup = 1 << 8;	/* turn on match20 wakeup   */
 	wakeup = 0;
 #endif
@@ -234,41 +294,62 @@ int au_sleep(void)
 	au_writel(wakeup, SYS_WAKEMSK);
 	au_sync();
 
-	save_and_sleep();
+	au_sleep();
+	ret = 0;
 
-	/*
-	 * After a wakeup, the cpu vectors back to 0x1fc00000, so
-	 * it's up to the boot code to get us back here.
-	 */
-	restore_core_regs();
+out_unlock:
 	spin_unlock_irqrestore(&pm_lock, flags);
-	return 0;
+	return ret;
 }
 
-static int pm_do_sleep(ctl_table *ctl, int write, struct file *file,
-		       void __user *buffer, size_t *len, loff_t *ppos)
+#if !defined(CONFIG_SOC_AU1200) && !defined(CONFIG_SOC_AU1550)
+
+/*
+ * This is right out of init/main.c
+ */
+
+/*
+ * This is the number of bits of precision for the loops_per_jiffy.
+ * Each bit takes on average 1.5/HZ seconds.  This (like the original)
+ * is a little better than 1%.
+ */
+#define LPS_PREC 8
+
+static void au1000_calibrate_delay(void)
 {
-#ifdef SLEEP_TEST_TIMEOUT
-#define TMPBUFLEN2 16
-	char buf[TMPBUFLEN2], *p;
-#endif
+	unsigned long ticks, loopbit;
+	int lps_precision = LPS_PREC;
 
-	if (!write)
-		*len = 0;
-	else {
-#ifdef SLEEP_TEST_TIMEOUT
-		if (*len > TMPBUFLEN2 - 1)
-			return -EFAULT;
-		if (copy_from_user(buf, buffer, *len))
-			return -EFAULT;
-		buf[*len] = 0;
-		p = buf;
-		sleep_ticks = simple_strtoul(p, &p, 0);
-#endif
+	loops_per_jiffy = 1 << 12;
 
-		au_sleep();
+	while (loops_per_jiffy <<= 1) {
+		/* Wait for "start of" clock tick */
+		ticks = jiffies;
+		while (ticks == jiffies)
+			/* nothing */ ;
+		/* Go ... */
+		ticks = jiffies;
+		__delay(loops_per_jiffy);
+		ticks = jiffies - ticks;
+		if (ticks)
+			break;
+	}
+
+	/*
+	 * Do a binary approximation to get loops_per_jiffy set to be equal
+	 * one clock (up to lps_precision bits)
+	 */
+	loops_per_jiffy >>= 1;
+	loopbit = loops_per_jiffy;
+	while (lps_precision-- && (loopbit >>= 1)) {
+		loops_per_jiffy |= loopbit;
+		ticks = jiffies;
+		while (ticks == jiffies);
+		ticks = jiffies;
+		__delay(loops_per_jiffy);
+		if (jiffies != ticks)	/* longer than 1 tick */
+			loops_per_jiffy &= ~loopbit;
 	}
-	return 0;
 }
 
 static int pm_do_freq(ctl_table *ctl, int write, struct file *file,
@@ -377,7 +458,7 @@ static int pm_do_freq(ctl_table *ctl, int write, struct file *file,
 
 	return retval;
 }
-
+#endif
 
 static struct ctl_table pm_table[] = {
 	{
@@ -388,6 +469,7 @@ static struct ctl_table pm_table[] = {
 		.mode		= 0600,
 		.proc_handler	= &pm_do_sleep
 	},
+#if !defined(CONFIG_SOC_AU1200) && !defined(CONFIG_SOC_AU1550)
 	{
 		.ctl_name	= CTL_UNNUMBERED,
 		.procname	= "freq",
@@ -396,6 +478,7 @@ static struct ctl_table pm_table[] = {
 		.mode		= 0600,
 		.proc_handler	= &pm_do_freq
 	},
+#endif
 	{}
 };
 
@@ -429,51 +512,4 @@ static int __init pm_init(void)
 
 __initcall(pm_init);
 
-/*
- * This is right out of init/main.c
- */
-
-/*
- * This is the number of bits of precision for the loops_per_jiffy.
- * Each bit takes on average 1.5/HZ seconds.  This (like the original)
- * is a little better than 1%.
- */
-#define LPS_PREC 8
-
-static void au1000_calibrate_delay(void)
-{
-	unsigned long ticks, loopbit;
-	int lps_precision = LPS_PREC;
-
-	loops_per_jiffy = 1 << 12;
-
-	while (loops_per_jiffy <<= 1) {
-		/* Wait for "start of" clock tick */
-		ticks = jiffies;
-		while (ticks == jiffies)
-			/* nothing */ ;
-		/* Go ... */
-		ticks = jiffies;
-		__delay(loops_per_jiffy);
-		ticks = jiffies - ticks;
-		if (ticks)
-			break;
-	}
-
-	/*
-	 * Do a binary approximation to get loops_per_jiffy set to be equal
-	 * one clock (up to lps_precision bits)
-	 */
-	loops_per_jiffy >>= 1;
-	loopbit = loops_per_jiffy;
-	while (lps_precision-- && (loopbit >>= 1)) {
-		loops_per_jiffy |= loopbit;
-		ticks = jiffies;
-		while (ticks == jiffies);
-		ticks = jiffies;
-		__delay(loops_per_jiffy);
-		if (jiffies != ticks)	/* longer than 1 tick */
-			loops_per_jiffy &= ~loopbit;
-	}
-}
 #endif	/* CONFIG_PM */