MIPS: Alchemy: Stop IRQ name sharing

Eliminate the sharing of IRQ names among the differenct Alchemy
variants.  IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.

This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!

Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.

Run-tested on DB1200.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

1 files changed, 30 insertions, 5 deletions

diff --git a/arch/mips/alchemy/common/time.c b/arch/mips/alchemy/common/time.c
index 379a664809b..2aecb2fdf98 100644
--- a/arch/mips/alchemy/common/time.c
+++ b/arch/mips/alchemy/common/time.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2008 Manuel Lauss <mano@roarinelk.homelinux.net>
+ * Copyright (C) 2008-2009 Manuel Lauss <manuel.lauss@gmail.com>
  *
  * Previous incarnations were:
  * Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
@@ -85,7 +85,6 @@ static struct clock_event_device au1x_rtcmatch2_clockdev = {
 	.name		= "rtcmatch2",
 	.features	= CLOCK_EVT_FEAT_ONESHOT,
 	.rating		= 100,
-	.irq		= AU1000_RTC_MATCH2_INT,
 	.set_next_event	= au1x_rtcmatch2_set_next_event,
 	.set_mode	= au1x_rtcmatch2_set_mode,
 	.cpumask	= cpu_all_mask,
@@ -98,11 +97,13 @@ static struct irqaction au1x_rtcmatch2_irqaction = {
 	.dev_id		= &au1x_rtcmatch2_clockdev,
 };
 
-void __init plat_time_init(void)
+static int __init alchemy_time_init(unsigned int m2int)
 {
 	struct clock_event_device *cd = &au1x_rtcmatch2_clockdev;
 	unsigned long t;
 
+	au1x_rtcmatch2_clockdev.irq = m2int;
+
 	/* Check if firmware (YAMON, ...) has enabled 32kHz and clock
 	 * has been detected.  If so install the rtcmatch2 clocksource,
 	 * otherwise don't bother.  Note that both bits being set is by
@@ -148,13 +149,18 @@ void __init plat_time_init(void)
 	cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd);
 	cd->min_delta_ns = clockevent_delta2ns(8, cd);	/* ~0.25ms */
 	clockevents_register_device(cd);
-	setup_irq(AU1000_RTC_MATCH2_INT, &au1x_rtcmatch2_irqaction);
+	setup_irq(m2int, &au1x_rtcmatch2_irqaction);
 
 	printk(KERN_INFO "Alchemy clocksource installed\n");
 
-	return;
+	return 0;
 
 cntr_err:
+	return -1;
+}
+
+static void __init alchemy_setup_c0timer(void)
+{
 	/*
 	 * MIPS kernel assigns 'au1k_wait' to 'cpu_wait' before this
 	 * function is called.  Because the Alchemy counters are unusable
@@ -166,3 +172,22 @@ cntr_err:
 	r4k_clockevent_init();
 	init_r4k_clocksource();
 }
+
+static int alchemy_m2inttab[] __initdata = {
+	AU1000_RTC_MATCH2_INT,
+	AU1500_RTC_MATCH2_INT,
+	AU1100_RTC_MATCH2_INT,
+	AU1550_RTC_MATCH2_INT,
+	AU1200_RTC_MATCH2_INT,
+};
+
+void __init plat_time_init(void)
+{
+	int t;
+
+	t = alchemy_get_cputype();
+	if (t == ALCHEMY_CPU_UNKNOWN)
+		alchemy_setup_c0timer();
+	else if (alchemy_time_init(alchemy_m2inttab[t]))
+		alchemy_setup_c0timer();
+}