MIPS: Alchemy: merge devboard code into single per-board files.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

1 files changed, 198 insertions, 0 deletions

diff --git a/arch/mips/alchemy/devboards/pb1500.c b/arch/mips/alchemy/devboards/pb1500.c
new file mode 100644
index 00000000000..e7b807b3ec5
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1500.c
@@ -0,0 +1,198 @@
+/*
+ * Pb1500 board support.
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+	return "PB1500";
+}
+
+void __init board_setup(void)
+{
+	u32 pin_func;
+	u32 sys_freqctrl, sys_clksrc;
+
+	bcsr_init(DB1000_BCSR_PHYS_ADDR,
+		  DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+	sys_clksrc = sys_freqctrl = pin_func = 0;
+	/* Set AUX clock to 12 MHz * 8 = 96 MHz */
+	au_writel(8, SYS_AUXPLL);
+	alchemy_gpio1_input_enable();
+	udelay(100);
+
+	/* GPIO201 is input for PCMCIA card detect */
+	/* GPIO203 is input for PCMCIA interrupt request */
+	alchemy_gpio_direction_input(201);
+	alchemy_gpio_direction_input(203);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+
+	/* Zero and disable FREQ2 */
+	sys_freqctrl = au_readl(SYS_FREQCTRL0);
+	sys_freqctrl &= ~0xFFF00000;
+	au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+	/* zero and disable USBH/USBD clocks */
+	sys_clksrc = au_readl(SYS_CLKSRC);
+	sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+			SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+	au_writel(sys_clksrc, SYS_CLKSRC);
+
+	sys_freqctrl = au_readl(SYS_FREQCTRL0);
+	sys_freqctrl &= ~0xFFF00000;
+
+	sys_clksrc = au_readl(SYS_CLKSRC);
+	sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+			SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+
+	/* FREQ2 = aux/2 = 48 MHz */
+	sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
+	au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+	/*
+	 * Route 48MHz FREQ2 into USB Host and/or Device
+	 */
+	sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
+	au_writel(sys_clksrc, SYS_CLKSRC);
+
+	pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+	/* 2nd USB port is USB host */
+	pin_func |= SYS_PF_USB;
+	au_writel(pin_func, SYS_PINFUNC);
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+#ifdef CONFIG_PCI
+	{
+		void __iomem *base =
+				(void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR);
+		/* Setup PCI bus controller */
+		__raw_writel(0x00003fff, base + PCI_REG_CMEM);
+		__raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV);
+		__raw_writel(0, base + PCI_REG_MWBASE_REV_CCL);
+		__raw_writel(0x02a00356, base + PCI_REG_STATCMD);
+		__raw_writel(0x00003c04, base + PCI_REG_PARAM);
+		__raw_writel(0x00000008, base + PCI_REG_MBAR);
+		wmb();
+	}
+#endif
+
+	/* Enable sys bus clock divider when IDLE state or no bus activity. */
+	au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+	/* Enable the RTC if not already enabled */
+	if (!(au_readl(0xac000028) & 0x20)) {
+		printk(KERN_INFO "enabling clock ...\n");
+		au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
+	}
+	/* Put the clock in BCD mode */
+	if (au_readl(0xac00002c) & 0x4) { /* reg B */
+		au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
+		au_sync();
+	}
+}
+
+/******************************************************************************/
+
+static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+	if ((slot < 12) || (slot > 13) || pin == 0)
+		return -1;
+	if (slot == 12)
+		return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+	if (slot == 13) {
+		switch (pin) {
+		case 1: return AU1500_PCI_INTA;
+		case 2: return AU1500_PCI_INTB;
+		case 3: return AU1500_PCI_INTC;
+		case 4: return AU1500_PCI_INTD;
+		}
+	}
+	return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+	[0] = {
+		.start	= AU1500_PCI_PHYS_ADDR,
+		.end	= AU1500_PCI_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct alchemy_pci_platdata pb1500_pci_pd = {
+	.board_map_irq	= pb1500_map_pci_irq,
+	.pci_cfg_set	= PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+			  PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+			  PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+			  0,
+#endif
+};
+
+static struct platform_device pb1500_pci_host = {
+	.dev.platform_data = &pb1500_pci_pd,
+	.name		= "alchemy-pci",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(alchemy_pci_host_res),
+	.resource	= alchemy_pci_host_res,
+};
+
+static int __init pb1500_dev_init(void)
+{
+	int swapped;
+
+	irq_set_irq_type(AU1500_GPIO9_INT,   IRQF_TRIGGER_LOW);   /* CD0# */
+	irq_set_irq_type(AU1500_GPIO10_INT,  IRQF_TRIGGER_LOW);  /* CARD0 */
+	irq_set_irq_type(AU1500_GPIO11_INT,  IRQF_TRIGGER_LOW);  /* STSCHG0# */
+	irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+	irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+	irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+	irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+	irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+
+	/* PCMCIA. single socket, identical to Pb1100 */
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		AU1500_GPIO11_INT, AU1500_GPIO9_INT,	 /* card / insert */
+		/*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+	swapped = bcsr_read(BCSR_STATUS) &  BCSR_STATUS_DB1000_SWAPBOOT;
+	db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+	platform_device_register(&pb1500_pci_host);
+
+	return 0;
+}
+arch_initcall(pb1500_dev_init);