Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (49 commits)
  MIPS: RB532: provide GPIO_BUILTIN_NR and irq_to_gpio/gpio_to_irq
  MIPS: Move ptrace prototypes to ptrace.h
  MIPS: Ptrace support for HARDWARE_WATCHPOINTS
  MIPS: Scheduler support for HARDWARE_WATCHPOINTS.
  MIPS: Watch exception handling for HARDWARE_WATCHPOINTS.
  MIPS: Probe watch registers and report configuration.
  MIPS: Add HARDWARE_WATCHPOINTS definitions and support code.
  MIPS: Add HARDWARE_WATCHPOINTS configure option.
  MIPS: Replace use of <asm-generic/uaccess.h> with native implementations.
  MIPS: TXx9: Add TX4939 ATA support (v2)
  MIPS: Rewrite spinlocks to ticket locks.
  MIPS: IP checksums: Optimize adjust of sum on buffers of odd alignment.
  MIPS: IP checksums: Remove unncessary .set pseudos
  MIPS: IP checksums: Remove unncessary folding of sum to 16 bit.
  MIPS: Move headfiles to new location below arch/mips/include
  MIPS: Alchemy: rename directory
  MIPS: Optimize get_user and put_user for 64-bit
  MIPS: TXx9: Implement prom_free_prom_memory
  MIPS: TXx9: Add RBTX4939 board support
  MIPS: TXx9: Add TX4939 SoC support
  ...

1 files changed, 162 insertions, 0 deletions

diff --git a/arch/mips/alchemy/pb1200/board_setup.c b/arch/mips/alchemy/pb1200/board_setup.c
new file mode 100644
index 00000000000..6cb2115059a
--- /dev/null
+++ b/arch/mips/alchemy/pb1200/board_setup.c
@@ -0,0 +1,162 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *	Alchemy Pb1200/Db1200 board setup.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/sched.h>
+
+#include <prom.h>
+#include <au1xxx.h>
+
+extern void _board_init_irq(void);
+extern void (*board_init_irq)(void);
+
+void board_reset(void)
+{
+	bcsr->resets = 0;
+	bcsr->system = 0;
+}
+
+void __init board_setup(void)
+{
+	char *argptr = NULL;
+
+#if 0
+	{
+		u32 pin_func;
+
+		/*
+		 * Enable PSC1 SYNC for AC97.  Normaly done in audio driver,
+		 * but it is board specific code, so put it here.
+		 */
+		pin_func = au_readl(SYS_PINFUNC);
+		au_sync();
+		pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+		au_writel(pin_func, SYS_PINFUNC);
+
+		au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
+		au_sync();
+	}
+#endif
+
+#if defined(CONFIG_I2C_AU1550)
+	{
+		u32 freq0, clksrc;
+		u32 pin_func;
+
+		/* Select SMBus in CPLD */
+		bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
+
+		pin_func = au_readl(SYS_PINFUNC);
+		au_sync();
+		pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+		/* Set GPIOs correctly */
+		pin_func |= 2 << 17;
+		au_writel(pin_func, SYS_PINFUNC);
+		au_sync();
+
+		/* The I2C driver depends on 50 MHz clock */
+		freq0 = au_readl(SYS_FREQCTRL0);
+		au_sync();
+		freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
+		freq0 |= 3 << SYS_FC_FRDIV1_BIT;
+		/* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
+		au_writel(freq0, SYS_FREQCTRL0);
+		au_sync();
+		freq0 |= SYS_FC_FE1;
+		au_writel(freq0, SYS_FREQCTRL0);
+		au_sync();
+
+		clksrc = au_readl(SYS_CLKSRC);
+		au_sync();
+		clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
+		/* Bit 22 is EXTCLK0 for PSC0 */
+		clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
+		au_writel(clksrc, SYS_CLKSRC);
+		au_sync();
+	}
+#endif
+
+#ifdef CONFIG_FB_AU1200
+	argptr = prom_getcmdline();
+#ifdef CONFIG_MIPS_PB1200
+	strcat(argptr, " video=au1200fb:panel:bs");
+#endif
+#ifdef CONFIG_MIPS_DB1200
+	strcat(argptr, " video=au1200fb:panel:bs");
+#endif
+#endif
+
+	/*
+	 * The Pb1200 development board uses external MUX for PSC0 to
+	 * support SMB/SPI. bcsr->resets bit 12: 0=SMB 1=SPI
+	 */
+#ifdef CONFIG_I2C_AU1550
+	bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
+#endif
+	au_sync();
+
+#ifdef CONFIG_MIPS_PB1200
+	printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1200
+	printk(KERN_INFO "AMD Alchemy Db1200 Board\n");
+#endif
+
+	/* Setup Pb1200 External Interrupt Controller */
+	board_init_irq = _board_init_irq;
+}
+
+int board_au1200fb_panel(void)
+{
+	BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+	int p;
+
+	p = bcsr->switches;
+	p >>= 8;
+	p &= 0x0F;
+	return p;
+}
+
+int board_au1200fb_panel_init(void)
+{
+	/* Apply power */
+	BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+	bcsr->board |= BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD | BCSR_BOARD_LCDBL;
+	/* printk(KERN_DEBUG "board_au1200fb_panel_init()\n"); */
+	return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+	/* Remove power */
+	BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+	bcsr->board &= ~(BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+			 BCSR_BOARD_LCDBL);
+	/* printk(KERN_DEBUG "board_au1200fb_panel_shutdown()\n"); */
+	return 0;
+}