Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
  serial8250: ratelimit "too much work" error
  serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
  serial: abstraction for 8250 legacy ports
  serial/imx: check that the buffer is non-empty before sending it out
  serial: mfd: add more baud rates support
  jsm: Remove the uart port on errors
  Alchemy: Add UART PM methods.
  8250: allow platforms to override PM hook.
  altera_uart: Don't use plain integer as NULL pointer
  altera_uart: Fix missing prototype for registering an early console
  altera_uart: Fixup type usage of port flags
  altera_uart: Make it possible to use Altera UART and 8250 ports together
  altera_uart: Add support for different address strides
  altera_uart: Add support for getting mapbase and IRQ from resources
  altera_uart: Add support for polling mode (IRQ-less)
  serial: Factor out uart_poll_timeout() from 8250 driver
  serial: mark the 8250 driver as maintained
  serial: 8250: Don't delay after transmitter is ready.
  tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
  vcs: invoke the vt update callback when /dev/vcs* is written to
  ...

2 files changed, 28 insertions, 35 deletions

diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 1dc55ee2681..3691630931d 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -24,6 +24,33 @@
 
 #include <prom.h>
 
+static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
+			    unsigned int old_state)
+{
+	switch (state) {
+	case 0:
+		if ((__raw_readl(port->membase + UART_MOD_CNTRL) & 3) != 3) {
+			/* power-on sequence as suggested in the databooks */
+			__raw_writel(0, port->membase + UART_MOD_CNTRL);
+			wmb();
+			__raw_writel(1, port->membase + UART_MOD_CNTRL);
+			wmb();
+		}
+		__raw_writel(3, port->membase + UART_MOD_CNTRL); /* full on */
+		wmb();
+		serial8250_do_pm(port, state, old_state);
+		break;
+	case 3:		/* power off */
+		serial8250_do_pm(port, state, old_state);
+		__raw_writel(0, port->membase + UART_MOD_CNTRL);
+		wmb();
+		break;
+	default:
+		serial8250_do_pm(port, state, old_state);
+		break;
+	}
+}
+
 #define PORT(_base, _irq)					\
 	{							\
 		.mapbase	= _base,			\
@@ -33,6 +60,7 @@
 		.flags		= UPF_SKIP_TEST | UPF_IOREMAP |	\
 				  UPF_FIXED_TYPE,		\
 		.type		= PORT_16550A,			\
+		.pm		= alchemy_8250_pm,		\
 	}
 
 static struct plat_serial8250_port au1x00_uart_data[] = {
diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c
index 5ef06a164a8..e5916a516e5 100644
--- a/arch/mips/alchemy/common/power.c
+++ b/arch/mips/alchemy/common/power.c
@@ -49,11 +49,6 @@
  * We only have to save/restore registers that aren't otherwise
  * done as part of a driver pm_* function.
  */
-static unsigned int sleep_uart0_inten;
-static unsigned int sleep_uart0_fifoctl;
-static unsigned int sleep_uart0_linectl;
-static unsigned int sleep_uart0_clkdiv;
-static unsigned int sleep_uart0_enable;
 static unsigned int sleep_usb[2];
 static unsigned int sleep_sys_clocks[5];
 static unsigned int sleep_sys_pinfunc;
@@ -62,22 +57,6 @@ static unsigned int sleep_static_memctlr[4][3];
 
 static void save_core_regs(void)
 {
-	extern void save_au1xxx_intctl(void);
-	extern void pm_eth0_shutdown(void);
-
-	/*
-	 * Do the serial ports.....these really should be a pm_*
-	 * registered function by the driver......but of course the
-	 * standard serial driver doesn't understand our Au1xxx
-	 * unique registers.
-	 */
-	sleep_uart0_inten = au_readl(UART0_ADDR + UART_IER);
-	sleep_uart0_fifoctl = au_readl(UART0_ADDR + UART_FCR);
-	sleep_uart0_linectl = au_readl(UART0_ADDR + UART_LCR);
-	sleep_uart0_clkdiv = au_readl(UART0_ADDR + UART_CLK);
-	sleep_uart0_enable = au_readl(UART0_ADDR + UART_MOD_CNTRL);
-	au_sync();
-
 #ifndef CONFIG_SOC_AU1200
 	/* Shutdown USB host/device. */
 	sleep_usb[0] = au_readl(USB_HOST_CONFIG);
@@ -175,20 +154,6 @@ static void restore_core_regs(void)
 	au_writel(sleep_static_memctlr[3][0], MEM_STCFG3);
 	au_writel(sleep_static_memctlr[3][1], MEM_STTIME3);
 	au_writel(sleep_static_memctlr[3][2], MEM_STADDR3);
-
-	/*
-	 * Enable the UART if it was enabled before sleep.
-	 * I guess I should define module control bits........
-	 */
-	if (sleep_uart0_enable & 0x02) {
-		au_writel(0, UART0_ADDR + UART_MOD_CNTRL); au_sync();
-		au_writel(1, UART0_ADDR + UART_MOD_CNTRL); au_sync();
-		au_writel(3, UART0_ADDR + UART_MOD_CNTRL); au_sync();
-		au_writel(sleep_uart0_inten, UART0_ADDR + UART_IER); au_sync();
-		au_writel(sleep_uart0_fifoctl, UART0_ADDR + UART_FCR); au_sync();
-		au_writel(sleep_uart0_linectl, UART0_ADDR + UART_LCR); au_sync();
-		au_writel(sleep_uart0_clkdiv, UART0_ADDR + UART_CLK); au_sync();
-	}
 }
 
 void au_sleep(void)