MIPS: KVM: Add master disable count interface

Expose two new virtual registers to userland via the
KVM_{GET,SET}_ONE_REG ioctls.

KVM_REG_MIPS_COUNT_CTL is for timer configuration fields and just
contains a master disable count bit. This can be used by userland to
freeze the timer in order to read a consistent state from the timer
count value and timer interrupt pending bit. This cannot be done with
the CP0_Cause.DC bit because the timer interrupt pending bit (TI) is
also in CP0_Cause so it would be impossible to stop the timer without
also risking a race with an hrtimer interrupt and having to explicitly
check whether an interrupt should have occurred.

When the timer is re-enabled it resumes without losing time, i.e. the
CP0_Count value jumps to what it would have been had the timer not been
disabled, which would also be impossible to do from userland with
CP0_Cause.DC. The timer interrupt also cannot be lost, i.e. if a timer
interrupt would have occurred had the timer not been disabled it is
queued when the timer is re-enabled.

This works by storing the nanosecond monotonic time when the master
disable is set, and using it for various operations instead of the
current monotonic time (e.g. when recalculating the bias when the
CP0_Count is set), until the master disable is cleared again, i.e. the
timer state is read/written as it would have been at that time. This
state is exposed to userland via the read-only KVM_REG_MIPS_COUNT_RESUME
virtual register so that userland can determine the exact time the
master disable took effect.

This should allow userland to atomically save the state of the timer,
and later restore it.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

1 files changed, 28 insertions, 0 deletions

diff --git a/arch/mips/include/uapi/asm/kvm.h b/arch/mips/include/uapi/asm/kvm.h
index f09ff5ae205..f859fbada1f 100644
--- a/arch/mips/include/uapi/asm/kvm.h
+++ b/arch/mips/include/uapi/asm/kvm.h
@@ -106,6 +106,34 @@ struct kvm_fpu {
 #define KVM_REG_MIPS_LO (KVM_REG_MIPS | KVM_REG_SIZE_U64 | 33)
 #define KVM_REG_MIPS_PC (KVM_REG_MIPS | KVM_REG_SIZE_U64 | 34)
 
+/* KVM specific control registers */
+
+/*
+ * CP0_Count control
+ * DC:    Set 0: Master disable CP0_Count and set COUNT_RESUME to now
+ *        Set 1: Master re-enable CP0_Count with unchanged bias, handling timer
+ *               interrupts since COUNT_RESUME
+ *        This can be used to freeze the timer to get a consistent snapshot of
+ *        the CP0_Count and timer interrupt pending state, while also resuming
+ *        safely without losing time or guest timer interrupts.
+ * Other: Reserved, do not change.
+ */
+#define KVM_REG_MIPS_COUNT_CTL		(KVM_REG_MIPS | KVM_REG_SIZE_U64 | \
+					 0x20000 | 0)
+#define KVM_REG_MIPS_COUNT_CTL_DC	0x00000001
+
+/*
+ * CP0_Count resume monotonic nanoseconds
+ * The monotonic nanosecond time of the last set of COUNT_CTL.DC (master
+ * disable). Any reads and writes of Count related registers while
+ * COUNT_CTL.DC=1 will appear to occur at this time. When COUNT_CTL.DC is
+ * cleared again (master enable) any timer interrupts since this time will be
+ * emulated.
+ * Modifications to times in the future are rejected.
+ */
+#define KVM_REG_MIPS_COUNT_RESUME	(KVM_REG_MIPS | KVM_REG_SIZE_U64 | \
+					 0x20000 | 1)
+
 /*
  * KVM MIPS specific structures and definitions
  *