MIPS: PNX8550: Move code one directory level up.

It was sharing the nxp directory but no code with pnx833x and will fit
better into the new platform makefile scheme, if moved.  Also after the
pnx833x code has been moved up, the pnx8550 Code was the last users of
the nxp dir.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

1 files changed, 145 insertions, 0 deletions

diff --git a/arch/mips/pnx8550/common/setup.c b/arch/mips/pnx8550/common/setup.c
new file mode 100644
index 00000000000..64246c9c875
--- /dev/null
+++ b/arch/mips/pnx8550/common/setup.c
@@ -0,0 +1,145 @@
+/*
+ *
+ * 2.6 port, Embedded Alley Solutions, Inc
+ *
+ *  Based on Per Hallsmark, per.hallsmark@mvista.com
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ */
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/serial_pnx8xxx.h>
+#include <linux/pm.h>
+
+#include <asm/cpu.h>
+#include <asm/bootinfo.h>
+#include <asm/irq.h>
+#include <asm/mipsregs.h>
+#include <asm/reboot.h>
+#include <asm/pgtable.h>
+#include <asm/time.h>
+
+#include <glb.h>
+#include <int.h>
+#include <pci.h>
+#include <uart.h>
+#include <nand.h>
+
+extern void __init board_setup(void);
+extern void pnx8550_machine_restart(char *);
+extern void pnx8550_machine_halt(void);
+extern void pnx8550_machine_power_off(void);
+extern struct resource ioport_resource;
+extern struct resource iomem_resource;
+extern char *prom_getcmdline(void);
+
+struct resource standard_io_resources[] = {
+	{
+		.start	= 0x00,
+		.end	= 0x1f,
+		.name	= "dma1",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	= 0x40,
+		.end	= 0x5f,
+		.name	= "timer",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	= 0x80,
+		.end	= 0x8f,
+		.name	= "dma page reg",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	= 0xc0,
+		.end	= 0xdf,
+		.name	= "dma2",
+		.flags	= IORESOURCE_BUSY
+	},
+};
+
+#define STANDARD_IO_RESOURCES ARRAY_SIZE(standard_io_resources)
+
+extern struct resource pci_io_resource;
+extern struct resource pci_mem_resource;
+
+/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
+unsigned long get_system_mem_size(void)
+{
+	/* Read IP2031_RANK0_ADDR_LO */
+	unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
+	/* Read IP2031_RANK1_ADDR_HI */
+	unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
+
+	return dram_r1_hi - dram_r0_lo + 1;
+}
+
+int pnx8550_console_port = -1;
+
+void __init plat_mem_setup(void)
+{
+	int i;
+	char* argptr;
+
+	board_setup();  /* board specific setup */
+
+        _machine_restart = pnx8550_machine_restart;
+        _machine_halt = pnx8550_machine_halt;
+        pm_power_off = pnx8550_machine_power_off;
+
+	/* Clear the Global 2 Register, PCI Inta Output Enable Registers
+	   Bit 1:Enable DAC Powerdown
+	  -> 0:DACs are enabled and are working normally
+	     1:DACs are powerdown
+	   Bit 0:Enable of PCI inta output
+	  -> 0 = Disable PCI inta output
+	     1 = Enable PCI inta output
+	*/
+	PNX8550_GLB2_ENAB_INTA_O = 0;
+
+	/* IO/MEM resources. */
+	set_io_port_base(PNX8550_PORT_BASE);
+	ioport_resource.start = 0;
+	ioport_resource.end = ~0;
+	iomem_resource.start = 0;
+	iomem_resource.end = ~0;
+
+	/* Request I/O space for devices on this board */
+	for (i = 0; i < STANDARD_IO_RESOURCES; i++)
+		request_resource(&ioport_resource, standard_io_resources + i);
+
+	/* Place the Mode Control bit for GPIO pin 16 in primary function */
+	/* Pin 16 is used by UART1, UA1_TX                                */
+	outl((PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_16_BIT) |
+			(PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_17_BIT),
+			PNX8550_GPIO_MC1);
+
+	argptr = prom_getcmdline();
+	if ((argptr = strstr(argptr, "console=ttyS")) != NULL) {
+		argptr += strlen("console=ttyS");
+		pnx8550_console_port = *argptr == '0' ? 0 : 1;
+
+		/* We must initialize the UART (console) before early printk */
+		/* Set LCR to 8-bit and BAUD to 38400 (no 5)                */
+		ip3106_lcr(UART_BASE, pnx8550_console_port) =
+			PNX8XXX_UART_LCR_8BIT;
+		ip3106_baud(UART_BASE, pnx8550_console_port) = 5;
+	}
+
+	return;
+}