[POWERPC] QE: Add support for Freescale QUICCEngine UART

Add support for UART serial ports using a Freescale QUICCEngine. Update
booting-without-of.txt to define new properties for a QE UART node.  Update
the MPC8323E-MDS device tree to add UCC5 as a UART.  Update the QE library
to support slow UCC devices and modules.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

1 files changed, 50 insertions, 0 deletions

diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts
index 5093ef304ff..690252456d3 100644
--- a/arch/powerpc/boot/dts/mpc832x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc832x_mds.dts
@@ -7,6 +7,18 @@
  * under  the terms of  the GNU General  Public License as published by the
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
+
+ * To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
+ * this:
+ *
+ * 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
+ * 2) Solder a wire from U61-21 to P19A-23.  P19 is a grid of pins on the board
+ *    next to the serial ports.
+ * 3) Solder a wire from U61-22 to P19K-22.
+ *
+ * Note that there's a typo in the schematic.  The board labels the last column
+ * of pins "P19K", but in the schematic, that column is called "P19J".  So if
+ * you're going by the schematic, the pin is called "P19J-K22".
  */
 
 / {
@@ -169,6 +181,23 @@
 					1 1e  1  0  1  0 	/* TX_EN */
 					1 1f  2  0  1  0>;/* CRS */
 			};
+			pio5: ucc_pin@05 {
+				pio-map = <
+				/*
+				 *    		      open       has
+				 *   port  pin  dir  drain  sel  irq
+				 */
+					2    0    1      0    2    0  /* TxD5 */
+					2    8    2      0    2    0  /* RxD5 */
+
+					2   1d    2      0    0    0  /* CTS5 */
+					2   1f    1      0    2    0  /* RTS5 */
+
+					2   18    2      0    0    0  /* CD */
+
+				>;
+			};
+
 		};
 	};
 
@@ -176,6 +205,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "qe";
+		compatible = "fsl,qe";
 		model = "QE";
 		ranges = <0 e0100000 00100000>;
 		reg = <e0100000 480>;
@@ -249,6 +279,26 @@
 			pio-handle = < &pio4 >;
 		};
 
+		ucc@2400 {
+			device_type = "serial";
+			compatible = "ucc_uart";
+			model = "UCC";
+			device-id = <5>;	/* The UCC number, 1-7*/
+			port-number = <0>;	/* Which ttyQEx device */
+			soft-uart;		/* We need Soft-UART */
+			reg = <2400 200>;
+			interrupts = <28>;	/* From Table 18-12 */
+			interrupt-parent = < &qeic >;
+			/*
+			 * For Soft-UART, we need to set TX to 1X, which
+			 * means specifying separate clock sources.
+			 */
+			rx-clock-name = "brg5";
+			tx-clock-name = "brg6";
+			pio-handle = < &pio5 >;
+		};
+
+
 		mdio@2320 {
 			#address-cells = <1>;
 			#size-cells = <0>;