powerpc/5200: Trim cruft from device trees

Trim out obsolete/extraneous properties and tighten up some usage
conventions.  Changes include:
- removal of device_type properties
- removal of cell-index properties
- Addition of gpio-controller and #gpio-cells properties to gpio
  nodes
- Move common interrupt-parent property out of device nodes and
  into top level parent node.

This patch also include what looks to be just trivial editorial
whitespace/format changes, but there is real method in this
madness.  Editorial changes were made to keep the all the
mpc5200 board device trees as similar as possible so that diffs
between them only show the real differences between the boards.
The pcm030 device tree was most affected by this because many
of the comments had been changed from // to /* */ style and
some cell values where changed from decimal to hex format when
it was cloned from one of the other 5200 device trees.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>

1 files changed, 6 insertions, 26 deletions

diff --git a/arch/powerpc/boot/dts/tqm5200.dts b/arch/powerpc/boot/dts/tqm5200.dts
index 906302e26a6..c9590b58b7b 100644
--- a/arch/powerpc/boot/dts/tqm5200.dts
+++ b/arch/powerpc/boot/dts/tqm5200.dts
@@ -17,6 +17,7 @@
 	compatible = "tqc,tqm5200";
 	#address-cells = <1>;
 	#size-cells = <1>;
+	interrupt-parent = <&mpc5200_pic>;
 
 	cpus {
 		#address-cells = <1>;
@@ -66,36 +67,33 @@
 			compatible = "fsl,mpc5200-gpt";
 			reg = <0x600 0x10>;
 			interrupts = <1 9 0>;
-			interrupt-parent = <&mpc5200_pic>;
 			fsl,has-wdt;
 		};
 
 		can@900 {
 			compatible = "fsl,mpc5200-mscan";
 			interrupts = <2 17 0>;
-			interrupt-parent = <&mpc5200_pic>;
 			reg = <0x900 0x80>;
 		};
 
 		can@980 {
 			compatible = "fsl,mpc5200-mscan";
 			interrupts = <2 18 0>;
-			interrupt-parent = <&mpc5200_pic>;
 			reg = <0x980 0x80>;
 		};
 
-		gpio@b00 {
+		gpio_simple: gpio@b00 {
 			compatible = "fsl,mpc5200-gpio";
 			reg = <0xb00 0x40>;
 			interrupts = <1 7 0>;
-			interrupt-parent = <&mpc5200_pic>;
+			gpio-controller;
+			#gpio-cells = <2>;
 		};
 
 		usb@1000 {
 			compatible = "fsl,mpc5200-ohci","ohci-be";
 			reg = <0x1000 0xff>;
 			interrupts = <2 6 0>;
-			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		dma-controller@1200 {
@@ -105,7 +103,6 @@
 			              3 4 0  3 5 0  3 6 0  3 7 0
 			              3 8 0  3 9 0  3 10 0  3 11 0
 			              3 12 0  3 13 0  3 14 0  3 15 0>;
-			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		xlb@1f00 {
@@ -114,39 +111,28 @@
 		};
 
 		serial@2000 {		// PSC1
-			device_type = "serial";
 			compatible = "fsl,mpc5200-psc-uart";
-			port-number = <0>;  // Logical port assignment
 			reg = <0x2000 0x100>;
 			interrupts = <2 1 0>;
-			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		serial@2200 {		// PSC2
-			device_type = "serial";
 			compatible = "fsl,mpc5200-psc-uart";
-			port-number = <1>;  // Logical port assignment
 			reg = <0x2200 0x100>;
 			interrupts = <2 2 0>;
-			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		serial@2400 {		// PSC3
-			device_type = "serial";
 			compatible = "fsl,mpc5200-psc-uart";
-			port-number = <2>;  // Logical port assignment
 			reg = <0x2400 0x100>;
 			interrupts = <2 3 0>;
-			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		ethernet@3000 {
-			device_type = "network";
 			compatible = "fsl,mpc5200-fec";
 			reg = <0x3000 0x400>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <2 5 0>;
-			interrupt-parent = <&mpc5200_pic>;
 			phy-handle = <&phy0>;
 		};
 
@@ -156,10 +142,8 @@
 			compatible = "fsl,mpc5200-mdio";
 			reg = <0x3000 0x400>;       // fec range, since we need to setup fec interrupts
 			interrupts = <2 5 0>;   // these are for "mii command finished", not link changes & co.
-			interrupt-parent = <&mpc5200_pic>;
 
 			phy0: ethernet-phy@0 {
-				device_type = "ethernet-phy";
 				reg = <0>;
 			};
 		};
@@ -168,7 +152,6 @@
 			compatible = "fsl,mpc5200-ata";
 			reg = <0x3a00 0x100>;
 			interrupts = <2 7 0>;
-			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		i2c@3d40 {
@@ -177,7 +160,6 @@
 			compatible = "fsl,mpc5200-i2c","fsl-i2c";
 			reg = <0x3d40 0x40>;
 			interrupts = <2 16 0>;
-			interrupt-parent = <&mpc5200_pic>;
 			fsl5200-clocking;
 
 			 rtc@68 {
@@ -192,9 +174,8 @@
 		};
 	};
 
-	lpb {
-		model = "fsl,lpb";
-		compatible = "fsl,lpb";
+	localbus {
+		compatible = "fsl,mpc5200-lpb","simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
 		ranges = <0 0 0xfc000000 0x02000000>;
@@ -223,7 +204,6 @@
 				 0xc000 0 0 4 &mpc5200_pic 0 0 3>;
 		clock-frequency = <0>; // From boot loader
 		interrupts = <2 8 0 2 9 0 2 10 0>;
-		interrupt-parent = <&mpc5200_pic>;
 		bus-range = <0 0>;
 		ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000
 			  0x02000000 0 0x90000000 0x90000000 0 0x10000000