powerpc: Move include files to arch/powerpc/include/asm

from include/asm-powerpc.  This is the result of a

mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm

Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly.  Of the latter only
one was outside the arch code and it is a driver only built for powerpc.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

1 files changed, 315 insertions, 0 deletions

diff --git a/arch/powerpc/include/asm/cell-regs.h b/arch/powerpc/include/asm/cell-regs.h
new file mode 100644
index 00000000000..fd6fd00434e
--- /dev/null
+++ b/arch/powerpc/include/asm/cell-regs.h
@@ -0,0 +1,315 @@
+/*
+ * cbe_regs.h
+ *
+ * This file is intended to hold the various register definitions for CBE
+ * on-chip system devices (memory controller, IO controller, etc...)
+ *
+ * (C) Copyright IBM Corporation 2001,2006
+ *
+ * Authors: Maximino Aguilar (maguilar@us.ibm.com)
+ *          David J. Erb (djerb@us.ibm.com)
+ *
+ * (c) 2006 Benjamin Herrenschmidt <benh@kernel.crashing.org>, IBM Corp.
+ */
+
+#ifndef CBE_REGS_H
+#define CBE_REGS_H
+
+#include <asm/cell-pmu.h>
+
+/*
+ *
+ * Some HID register definitions
+ *
+ */
+
+/* CBE specific HID0 bits */
+#define HID0_CBE_THERM_WAKEUP	0x0000020000000000ul
+#define HID0_CBE_SYSERR_WAKEUP	0x0000008000000000ul
+#define HID0_CBE_THERM_INT_EN	0x0000000400000000ul
+#define HID0_CBE_SYSERR_INT_EN	0x0000000200000000ul
+
+#define MAX_CBE		2
+
+/*
+ *
+ * Pervasive unit register definitions
+ *
+ */
+
+union spe_reg {
+	u64 val;
+	u8 spe[8];
+};
+
+union ppe_spe_reg {
+	u64 val;
+	struct {
+		u32 ppe;
+		u32 spe;
+	};
+};
+
+
+struct cbe_pmd_regs {
+	/* Debug Bus Control */
+	u64	pad_0x0000;					/* 0x0000 */
+
+	u64	group_control;					/* 0x0008 */
+
+	u8	pad_0x0010_0x00a8 [0x00a8 - 0x0010];		/* 0x0010 */
+
+	u64	debug_bus_control;				/* 0x00a8 */
+
+	u8	pad_0x00b0_0x0100 [0x0100 - 0x00b0];		/* 0x00b0 */
+
+	u64	trace_aux_data;					/* 0x0100 */
+	u64	trace_buffer_0_63;				/* 0x0108 */
+	u64	trace_buffer_64_127;				/* 0x0110 */
+	u64	trace_address;					/* 0x0118 */
+	u64	ext_tr_timer;					/* 0x0120 */
+
+	u8	pad_0x0128_0x0400 [0x0400 - 0x0128];		/* 0x0128 */
+
+	/* Performance Monitor */
+	u64	pm_status;					/* 0x0400 */
+	u64	pm_control;					/* 0x0408 */
+	u64	pm_interval;					/* 0x0410 */
+	u64	pm_ctr[4];					/* 0x0418 */
+	u64	pm_start_stop;					/* 0x0438 */
+	u64	pm07_control[8];				/* 0x0440 */
+
+	u8	pad_0x0480_0x0800 [0x0800 - 0x0480];		/* 0x0480 */
+
+	/* Thermal Sensor Registers */
+	union	spe_reg	ts_ctsr1;				/* 0x0800 */
+	u64	ts_ctsr2;					/* 0x0808 */
+	union	spe_reg	ts_mtsr1;				/* 0x0810 */
+	u64	ts_mtsr2;					/* 0x0818 */
+	union	spe_reg	ts_itr1;				/* 0x0820 */
+	u64	ts_itr2;					/* 0x0828 */
+	u64	ts_gitr;					/* 0x0830 */
+	u64	ts_isr;						/* 0x0838 */
+	u64	ts_imr;						/* 0x0840 */
+	union	spe_reg	tm_cr1;					/* 0x0848 */
+	u64	tm_cr2;						/* 0x0850 */
+	u64	tm_simr;					/* 0x0858 */
+	union	ppe_spe_reg tm_tpr;				/* 0x0860 */
+	union	spe_reg	tm_str1;				/* 0x0868 */
+	u64	tm_str2;					/* 0x0870 */
+	union	ppe_spe_reg tm_tsr;				/* 0x0878 */
+
+	/* Power Management */
+	u64	pmcr;						/* 0x0880 */
+#define CBE_PMD_PAUSE_ZERO_CONTROL	0x10000
+	u64	pmsr;						/* 0x0888 */
+
+	/* Time Base Register */
+	u64	tbr;						/* 0x0890 */
+
+	u8	pad_0x0898_0x0c00 [0x0c00 - 0x0898];		/* 0x0898 */
+
+	/* Fault Isolation Registers */
+	u64	checkstop_fir;					/* 0x0c00 */
+	u64	recoverable_fir;				/* 0x0c08 */
+	u64	spec_att_mchk_fir;				/* 0x0c10 */
+	u32	fir_mode_reg;					/* 0x0c18 */
+	u8	pad_0x0c1c_0x0c20 [4];				/* 0x0c1c */
+#define CBE_PMD_FIR_MODE_M8		0x00800
+	u64	fir_enable_mask;				/* 0x0c20 */
+
+	u8	pad_0x0c28_0x0ca8 [0x0ca8 - 0x0c28];		/* 0x0c28 */
+	u64	ras_esc_0;					/* 0x0ca8 */
+	u8	pad_0x0cb0_0x1000 [0x1000 - 0x0cb0];		/* 0x0cb0 */
+};
+
+extern struct cbe_pmd_regs __iomem *cbe_get_pmd_regs(struct device_node *np);
+extern struct cbe_pmd_regs __iomem *cbe_get_cpu_pmd_regs(int cpu);
+
+/*
+ * PMU shadow registers
+ *
+ * Many of the registers in the performance monitoring unit are write-only,
+ * so we need to save a copy of what we write to those registers.
+ *
+ * The actual data counters are read/write. However, writing to the counters
+ * only takes effect if the PMU is enabled. Otherwise the value is stored in
+ * a hardware latch until the next time the PMU is enabled. So we save a copy
+ * of the counter values if we need to read them back while the PMU is
+ * disabled. The counter_value_in_latch field is a bitmap indicating which
+ * counters currently have a value waiting to be written.
+ */
+
+struct cbe_pmd_shadow_regs {
+	u32 group_control;
+	u32 debug_bus_control;
+	u32 trace_address;
+	u32 ext_tr_timer;
+	u32 pm_status;
+	u32 pm_control;
+	u32 pm_interval;
+	u32 pm_start_stop;
+	u32 pm07_control[NR_CTRS];
+
+	u32 pm_ctr[NR_PHYS_CTRS];
+	u32 counter_value_in_latch;
+};
+
+extern struct cbe_pmd_shadow_regs *cbe_get_pmd_shadow_regs(struct device_node *np);
+extern struct cbe_pmd_shadow_regs *cbe_get_cpu_pmd_shadow_regs(int cpu);
+
+/*
+ *
+ * IIC unit register definitions
+ *
+ */
+
+struct cbe_iic_pending_bits {
+	u32 data;
+	u8 flags;
+	u8 class;
+	u8 source;
+	u8 prio;
+};
+
+#define CBE_IIC_IRQ_VALID	0x80
+#define CBE_IIC_IRQ_IPI		0x40
+
+struct cbe_iic_thread_regs {
+	struct cbe_iic_pending_bits pending;
+	struct cbe_iic_pending_bits pending_destr;
+	u64 generate;
+	u64 prio;
+};
+
+struct cbe_iic_regs {
+	u8	pad_0x0000_0x0400[0x0400 - 0x0000];		/* 0x0000 */
+
+	/* IIC interrupt registers */
+	struct	cbe_iic_thread_regs thread[2];			/* 0x0400 */
+
+	u64	iic_ir;						/* 0x0440 */
+#define CBE_IIC_IR_PRIO(x)      (((x) & 0xf) << 12)
+#define CBE_IIC_IR_DEST_NODE(x) (((x) & 0xf) << 4)
+#define CBE_IIC_IR_DEST_UNIT(x) ((x) & 0xf)
+#define CBE_IIC_IR_IOC_0        0x0
+#define CBE_IIC_IR_IOC_1S       0xb
+#define CBE_IIC_IR_PT_0         0xe
+#define CBE_IIC_IR_PT_1         0xf
+
+	u64	iic_is;						/* 0x0448 */
+#define CBE_IIC_IS_PMI		0x2
+
+	u8	pad_0x0450_0x0500[0x0500 - 0x0450];		/* 0x0450 */
+
+	/* IOC FIR */
+	u64	ioc_fir_reset;					/* 0x0500 */
+	u64	ioc_fir_set;					/* 0x0508 */
+	u64	ioc_checkstop_enable;				/* 0x0510 */
+	u64	ioc_fir_error_mask;				/* 0x0518 */
+	u64	ioc_syserr_enable;				/* 0x0520 */
+	u64	ioc_fir;					/* 0x0528 */
+
+	u8	pad_0x0530_0x1000[0x1000 - 0x0530];		/* 0x0530 */
+};
+
+extern struct cbe_iic_regs __iomem *cbe_get_iic_regs(struct device_node *np);
+extern struct cbe_iic_regs __iomem *cbe_get_cpu_iic_regs(int cpu);
+
+
+struct cbe_mic_tm_regs {
+	u8	pad_0x0000_0x0040[0x0040 - 0x0000];		/* 0x0000 */
+
+	u64	mic_ctl_cnfg2;					/* 0x0040 */
+#define CBE_MIC_ENABLE_AUX_TRC		0x8000000000000000LL
+#define CBE_MIC_DISABLE_PWR_SAV_2	0x0200000000000000LL
+#define CBE_MIC_DISABLE_AUX_TRC_WRAP	0x0100000000000000LL
+#define CBE_MIC_ENABLE_AUX_TRC_INT	0x0080000000000000LL
+
+	u64	pad_0x0048;					/* 0x0048 */
+
+	u64	mic_aux_trc_base;				/* 0x0050 */
+	u64	mic_aux_trc_max_addr;				/* 0x0058 */
+	u64	mic_aux_trc_cur_addr;				/* 0x0060 */
+	u64	mic_aux_trc_grf_addr;				/* 0x0068 */
+	u64	mic_aux_trc_grf_data;				/* 0x0070 */
+
+	u64	pad_0x0078;					/* 0x0078 */
+
+	u64	mic_ctl_cnfg_0;					/* 0x0080 */
+#define CBE_MIC_DISABLE_PWR_SAV_0	0x8000000000000000LL
+
+	u64	pad_0x0088;					/* 0x0088 */
+
+	u64	slow_fast_timer_0;				/* 0x0090 */
+	u64	slow_next_timer_0;				/* 0x0098 */
+
+	u8	pad_0x00a0_0x00f8[0x00f8 - 0x00a0];		/* 0x00a0 */
+	u64    	mic_df_ecc_address_0;				/* 0x00f8 */
+
+	u8	pad_0x0100_0x01b8[0x01b8 - 0x0100];		/* 0x0100 */
+	u64    	mic_df_ecc_address_1;				/* 0x01b8 */
+
+	u64	mic_ctl_cnfg_1;					/* 0x01c0 */
+#define CBE_MIC_DISABLE_PWR_SAV_1	0x8000000000000000LL
+
+	u64	pad_0x01c8;					/* 0x01c8 */
+
+	u64	slow_fast_timer_1;				/* 0x01d0 */
+	u64	slow_next_timer_1;				/* 0x01d8 */
+
+	u8	pad_0x01e0_0x0208[0x0208 - 0x01e0];		/* 0x01e0 */
+	u64	mic_exc;					/* 0x0208 */
+#define CBE_MIC_EXC_BLOCK_SCRUB		0x0800000000000000ULL
+#define CBE_MIC_EXC_FAST_SCRUB		0x0100000000000000ULL
+
+	u64	mic_mnt_cfg;					/* 0x0210 */
+#define CBE_MIC_MNT_CFG_CHAN_0_POP	0x0002000000000000ULL
+#define CBE_MIC_MNT_CFG_CHAN_1_POP	0x0004000000000000ULL
+
+	u64	mic_df_config;					/* 0x0218 */
+#define CBE_MIC_ECC_DISABLE_0		0x4000000000000000ULL
+#define CBE_MIC_ECC_REP_SINGLE_0	0x2000000000000000ULL
+#define CBE_MIC_ECC_DISABLE_1		0x0080000000000000ULL
+#define CBE_MIC_ECC_REP_SINGLE_1	0x0040000000000000ULL
+
+	u8	pad_0x0220_0x0230[0x0230 - 0x0220];		/* 0x0220 */
+	u64	mic_fir;					/* 0x0230 */
+#define CBE_MIC_FIR_ECC_SINGLE_0_ERR	0x0200000000000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_0_ERR	0x0100000000000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_1_ERR	0x0080000000000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_1_ERR	0x0040000000000000ULL
+#define CBE_MIC_FIR_ECC_ERR_MASK	0xffff000000000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_0_CTE	0x0000020000000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_0_CTE	0x0000010000000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_1_CTE	0x0000008000000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_1_CTE	0x0000004000000000ULL
+#define CBE_MIC_FIR_ECC_CTE_MASK	0x0000ffff00000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_0_RESET	0x0000000002000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_0_RESET	0x0000000001000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_1_RESET	0x0000000000800000ULL
+#define CBE_MIC_FIR_ECC_MULTI_1_RESET	0x0000000000400000ULL
+#define CBE_MIC_FIR_ECC_RESET_MASK	0x00000000ffff0000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_0_SET	0x0000000000000200ULL
+#define CBE_MIC_FIR_ECC_MULTI_0_SET	0x0000000000000100ULL
+#define CBE_MIC_FIR_ECC_SINGLE_1_SET	0x0000000000000080ULL
+#define CBE_MIC_FIR_ECC_MULTI_1_SET	0x0000000000000040ULL
+#define CBE_MIC_FIR_ECC_SET_MASK	0x000000000000ffffULL
+	u64	mic_fir_debug;					/* 0x0238 */
+
+	u8	pad_0x0240_0x1000[0x1000 - 0x0240];		/* 0x0240 */
+};
+
+extern struct cbe_mic_tm_regs __iomem *cbe_get_mic_tm_regs(struct device_node *np);
+extern struct cbe_mic_tm_regs __iomem *cbe_get_cpu_mic_tm_regs(int cpu);
+
+/* some utility functions to deal with SMT */
+extern u32 cbe_get_hw_thread_id(int cpu);
+extern u32 cbe_cpu_to_node(int cpu);
+extern u32 cbe_node_to_cpu(int node);
+
+/* Init this module early */
+extern void cbe_regs_init(void);
+
+
+#endif /* CBE_REGS_H */