powerpc: Move include files to arch/powerpc/include/asm

from include/asm-powerpc.  This is the result of a

mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm

Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly.  Of the latter only
one was outside the arch code and it is a driver only built for powerpc.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

1 files changed, 290 insertions, 0 deletions

diff --git a/arch/powerpc/include/asm/ucc_slow.h b/arch/powerpc/include/asm/ucc_slow.h
new file mode 100644
index 00000000000..0980e6ad335
--- /dev/null
+++ b/arch/powerpc/include/asm/ucc_slow.h
@@ -0,0 +1,290 @@
+/*
+ * Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved.
+ *
+ * Authors: 	Shlomi Gridish <gridish@freescale.com>
+ * 		Li Yang <leoli@freescale.com>
+ *
+ * Description:
+ * Internal header file for UCC SLOW unit routines.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+#ifndef __UCC_SLOW_H__
+#define __UCC_SLOW_H__
+
+#include <linux/kernel.h>
+
+#include <asm/immap_qe.h>
+#include <asm/qe.h>
+
+#include "ucc.h"
+
+/* transmit BD's status */
+#define T_R	0x80000000	/* ready bit */
+#define T_PAD	0x40000000	/* add pads to short frames */
+#define T_W	0x20000000	/* wrap bit */
+#define T_I	0x10000000	/* interrupt on completion */
+#define T_L	0x08000000	/* last */
+
+#define T_A	0x04000000	/* Address - the data transmitted as address
+				   chars */
+#define T_TC	0x04000000	/* transmit CRC */
+#define T_CM	0x02000000	/* continuous mode */
+#define T_DEF	0x02000000	/* collision on previous attempt to transmit */
+#define T_P	0x01000000	/* Preamble - send Preamble sequence before
+				   data */
+#define T_HB	0x01000000	/* heartbeat */
+#define T_NS	0x00800000	/* No Stop */
+#define T_LC	0x00800000	/* late collision */
+#define T_RL	0x00400000	/* retransmission limit */
+#define T_UN	0x00020000	/* underrun */
+#define T_CT	0x00010000	/* CTS lost */
+#define T_CSL	0x00010000	/* carrier sense lost */
+#define T_RC	0x003c0000	/* retry count */
+
+/* Receive BD's status */
+#define R_E	0x80000000	/* buffer empty */
+#define R_W	0x20000000	/* wrap bit */
+#define R_I	0x10000000	/* interrupt on reception */
+#define R_L	0x08000000	/* last */
+#define R_C	0x08000000	/* the last byte in this buffer is a cntl
+				   char */
+#define R_F	0x04000000	/* first */
+#define R_A	0x04000000	/* the first byte in this buffer is address
+				   byte */
+#define R_CM	0x02000000	/* continuous mode */
+#define R_ID	0x01000000	/* buffer close on reception of idles */
+#define R_M	0x01000000	/* Frame received because of promiscuous
+				   mode */
+#define R_AM	0x00800000	/* Address match */
+#define R_DE	0x00800000	/* Address match */
+#define R_LG	0x00200000	/* Break received */
+#define R_BR	0x00200000	/* Frame length violation */
+#define R_NO	0x00100000	/* Rx Non Octet Aligned Packet */
+#define R_FR	0x00100000	/* Framing Error (no stop bit) character
+				   received */
+#define R_PR	0x00080000	/* Parity Error character received */
+#define R_AB	0x00080000	/* Frame Aborted */
+#define R_SH	0x00080000	/* frame is too short */
+#define R_CR	0x00040000	/* CRC Error */
+#define R_OV	0x00020000	/* Overrun */
+#define R_CD	0x00010000	/* CD lost */
+#define R_CL	0x00010000	/* this frame is closed because of a
+				   collision */
+
+/* Rx Data buffer must be 4 bytes aligned in most cases.*/
+#define UCC_SLOW_RX_ALIGN		4
+#define UCC_SLOW_MRBLR_ALIGNMENT	4
+#define UCC_SLOW_PRAM_SIZE		0x100
+#define ALIGNMENT_OF_UCC_SLOW_PRAM	64
+
+/* UCC Slow Channel Protocol Mode */
+enum ucc_slow_channel_protocol_mode {
+	UCC_SLOW_CHANNEL_PROTOCOL_MODE_QMC = 0x00000002,
+	UCC_SLOW_CHANNEL_PROTOCOL_MODE_UART = 0x00000004,
+	UCC_SLOW_CHANNEL_PROTOCOL_MODE_BISYNC = 0x00000008,
+};
+
+/* UCC Slow Transparent Transmit CRC (TCRC) */
+enum ucc_slow_transparent_tcrc {
+	/* 16-bit CCITT CRC (HDLC).  (X16 + X12 + X5 + 1) */
+	UCC_SLOW_TRANSPARENT_TCRC_CCITT_CRC16 = 0x00000000,
+	/* CRC16 (BISYNC).  (X16 + X15 + X2 + 1) */
+	UCC_SLOW_TRANSPARENT_TCRC_CRC16 = 0x00004000,
+	/* 32-bit CCITT CRC (Ethernet and HDLC) */
+	UCC_SLOW_TRANSPARENT_TCRC_CCITT_CRC32 = 0x00008000,
+};
+
+/* UCC Slow oversampling rate for transmitter (TDCR) */
+enum ucc_slow_tx_oversampling_rate {
+	/* 1x clock mode */
+	UCC_SLOW_OVERSAMPLING_RATE_TX_TDCR_1 = 0x00000000,
+	/* 8x clock mode */
+	UCC_SLOW_OVERSAMPLING_RATE_TX_TDCR_8 = 0x00010000,
+	/* 16x clock mode */
+	UCC_SLOW_OVERSAMPLING_RATE_TX_TDCR_16 = 0x00020000,
+	/* 32x clock mode */
+	UCC_SLOW_OVERSAMPLING_RATE_TX_TDCR_32 = 0x00030000,
+};
+
+/* UCC Slow Oversampling rate for receiver (RDCR)
+*/
+enum ucc_slow_rx_oversampling_rate {
+	/* 1x clock mode */
+	UCC_SLOW_OVERSAMPLING_RATE_RX_RDCR_1 = 0x00000000,
+	/* 8x clock mode */
+	UCC_SLOW_OVERSAMPLING_RATE_RX_RDCR_8 = 0x00004000,
+	/* 16x clock mode */
+	UCC_SLOW_OVERSAMPLING_RATE_RX_RDCR_16 = 0x00008000,
+	/* 32x clock mode */
+	UCC_SLOW_OVERSAMPLING_RATE_RX_RDCR_32 = 0x0000c000,
+};
+
+/* UCC Slow Transmitter encoding method (TENC)
+*/
+enum ucc_slow_tx_encoding_method {
+	UCC_SLOW_TRANSMITTER_ENCODING_METHOD_TENC_NRZ = 0x00000000,
+	UCC_SLOW_TRANSMITTER_ENCODING_METHOD_TENC_NRZI = 0x00000100
+};
+
+/* UCC Slow Receiver decoding method (RENC)
+*/
+enum ucc_slow_rx_decoding_method {
+	UCC_SLOW_RECEIVER_DECODING_METHOD_RENC_NRZ = 0x00000000,
+	UCC_SLOW_RECEIVER_DECODING_METHOD_RENC_NRZI = 0x00000800
+};
+
+/* UCC Slow Diagnostic mode (DIAG)
+*/
+enum ucc_slow_diag_mode {
+	UCC_SLOW_DIAG_MODE_NORMAL = 0x00000000,
+	UCC_SLOW_DIAG_MODE_LOOPBACK = 0x00000040,
+	UCC_SLOW_DIAG_MODE_ECHO = 0x00000080,
+	UCC_SLOW_DIAG_MODE_LOOPBACK_ECHO = 0x000000c0
+};
+
+struct ucc_slow_info {
+	int ucc_num;
+	int protocol;			/* QE_CR_PROTOCOL_xxx */
+	enum qe_clock rx_clock;
+	enum qe_clock tx_clock;
+	phys_addr_t regs;
+	int irq;
+	u16 uccm_mask;
+	int data_mem_part;
+	int init_tx;
+	int init_rx;
+	u32 tx_bd_ring_len;
+	u32 rx_bd_ring_len;
+	int rx_interrupts;
+	int brkpt_support;
+	int grant_support;
+	int tsa;
+	int cdp;
+	int cds;
+	int ctsp;
+	int ctss;
+	int rinv;
+	int tinv;
+	int rtsm;
+	int rfw;
+	int tci;
+	int tend;
+	int tfl;
+	int txsy;
+	u16 max_rx_buf_length;
+	enum ucc_slow_transparent_tcrc tcrc;
+	enum ucc_slow_channel_protocol_mode mode;
+	enum ucc_slow_diag_mode diag;
+	enum ucc_slow_tx_oversampling_rate tdcr;
+	enum ucc_slow_rx_oversampling_rate rdcr;
+	enum ucc_slow_tx_encoding_method tenc;
+	enum ucc_slow_rx_decoding_method renc;
+};
+
+struct ucc_slow_private {
+	struct ucc_slow_info *us_info;
+	struct ucc_slow __iomem *us_regs; /* Ptr to memory map of UCC regs */
+	struct ucc_slow_pram *us_pram;	/* a pointer to the parameter RAM */
+	u32 us_pram_offset;
+	int enabled_tx;		/* Whether channel is enabled for Tx (ENT) */
+	int enabled_rx;		/* Whether channel is enabled for Rx (ENR) */
+	int stopped_tx;		/* Whether channel has been stopped for Tx
+				   (STOP_TX, etc.) */
+	int stopped_rx;		/* Whether channel has been stopped for Rx */
+	struct list_head confQ;	/* frames passed to chip waiting for tx */
+	u32 first_tx_bd_mask;	/* mask is used in Tx routine to save status
+				   and length for first BD in a frame */
+	u32 tx_base_offset;	/* first BD in Tx BD table offset (In MURAM) */
+	u32 rx_base_offset;	/* first BD in Rx BD table offset (In MURAM) */
+	struct qe_bd *confBd;	/* next BD for confirm after Tx */
+	struct qe_bd *tx_bd;	/* next BD for new Tx request */
+	struct qe_bd *rx_bd;	/* next BD to collect after Rx */
+	void *p_rx_frame;	/* accumulating receive frame */
+	u16 *p_ucce;		/* a pointer to the event register in memory.
+				 */
+	u16 *p_uccm;		/* a pointer to the mask register in memory */
+	u16 saved_uccm;		/* a saved mask for the RX Interrupt bits */
+#ifdef STATISTICS
+	u32 tx_frames;		/* Transmitted frames counters */
+	u32 rx_frames;		/* Received frames counters (only frames
+				   passed to application) */
+	u32 rx_discarded;	/* Discarded frames counters (frames that
+				   were discarded by the driver due to
+				   errors) */
+#endif				/* STATISTICS */
+};
+
+/* ucc_slow_init
+ * Initializes Slow UCC according to provided parameters.
+ *
+ * us_info  - (In) pointer to the slow UCC info structure.
+ * uccs_ret - (Out) pointer to the slow UCC structure.
+ */
+int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** uccs_ret);
+
+/* ucc_slow_free
+ * Frees all resources for slow UCC.
+ *
+ * uccs - (In) pointer to the slow UCC structure.
+ */
+void ucc_slow_free(struct ucc_slow_private * uccs);
+
+/* ucc_slow_enable
+ * Enables a fast UCC port.
+ * This routine enables Tx and/or Rx through the General UCC Mode Register.
+ *
+ * uccs - (In) pointer to the slow UCC structure.
+ * mode - (In) TX, RX, or both.
+ */
+void ucc_slow_enable(struct ucc_slow_private * uccs, enum comm_dir mode);
+
+/* ucc_slow_disable
+ * Disables a fast UCC port.
+ * This routine disables Tx and/or Rx through the General UCC Mode Register.
+ *
+ * uccs - (In) pointer to the slow UCC structure.
+ * mode - (In) TX, RX, or both.
+ */
+void ucc_slow_disable(struct ucc_slow_private * uccs, enum comm_dir mode);
+
+/* ucc_slow_poll_transmitter_now
+ * Immediately forces a poll of the transmitter for data to be sent.
+ * Typically, the hardware performs a periodic poll for data that the
+ * transmit routine has set up to be transmitted. In cases where
+ * this polling cycle is not soon enough, this optional routine can
+ * be invoked to force a poll right away, instead. Proper use for
+ * each transmission for which this functionality is desired is to
+ * call the transmit routine and then this routine right after.
+ *
+ * uccs - (In) pointer to the slow UCC structure.
+ */
+void ucc_slow_poll_transmitter_now(struct ucc_slow_private * uccs);
+
+/* ucc_slow_graceful_stop_tx
+ * Smoothly stops transmission on a specified slow UCC.
+ *
+ * uccs - (In) pointer to the slow UCC structure.
+ */
+void ucc_slow_graceful_stop_tx(struct ucc_slow_private * uccs);
+
+/* ucc_slow_stop_tx
+ * Stops transmission on a specified slow UCC.
+ *
+ * uccs - (In) pointer to the slow UCC structure.
+ */
+void ucc_slow_stop_tx(struct ucc_slow_private * uccs);
+
+/* ucc_slow_restart_tx
+ * Restarts transmitting on a specified slow UCC.
+ *
+ * uccs - (In) pointer to the slow UCC structure.
+ */
+void ucc_slow_restart_tx(struct ucc_slow_private *uccs);
+
+u32 ucc_slow_get_qe_cr_subblock(int uccs_num);
+
+#endif				/* __UCC_SLOW_H__ */