powerpc: Allow perf_counters to access user memory at interrupt time

This provides a mechanism to allow the perf_counters code to access
user memory in a PMU interrupt routine.  Such an access can cause
various kinds of interrupt: SLB miss, MMU hash table miss, segment
table miss, or TLB miss, depending on the processor.  This commit
only deals with 64-bit classic/server processors, which use an MMU
hash table.  32-bit processors are already able to access user memory
at interrupt time.  Since we don't soft-disable on 32-bit, we avoid
the possibility of reentering hash_page or the TLB miss handlers,
since they run with interrupts disabled.

On 64-bit processors, an SLB miss interrupt on a user address will
update the slb_cache and slb_cache_ptr fields in the paca.  This is
OK except in the case where a PMU interrupt occurs in switch_slb,
which also accesses those fields.  To prevent this, we hard-disable
interrupts in switch_slb.  Interrupts are already soft-disabled at
this point, and will get hard-enabled when they get soft-enabled
later.

This also reworks slb_flush_and_rebolt: to avoid hard-disabling twice,
and to make sure that it clears the slb_cache_ptr when called from
other callers than switch_slb, the existing routine is renamed to
__slb_flush_and_rebolt, which is called by switch_slb and the new
version of slb_flush_and_rebolt.

Similarly, switch_stab (used on POWER3 and RS64 processors) gets a
hard_irq_disable() to protect the per-cpu variables used there and
in ste_allocate.

If a MMU hashtable miss interrupt occurs, normally we would call
hash_page to look up the Linux PTE for the address and create a HPTE.
However, hash_page is fairly complex and takes some locks, so to
avoid the possibility of deadlock, we check the preemption count
to see if we are in a (pseudo-)NMI handler, and if so, we don't call
hash_page but instead treat it like a bad access that will get
reported up through the exception table mechanism.  An interrupt
whose handler runs even though the interrupt occurred when
soft-disabled (such as the PMU interrupt) is considered a pseudo-NMI
handler, which should use nmi_enter()/nmi_exit() rather than
irq_enter()/irq_exit().

Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

1 files changed, 10 insertions, 1 deletions

diff --git a/arch/powerpc/mm/stab.c b/arch/powerpc/mm/stab.c
index 98cd1dc2ae7..ab5fb48b3e9 100644
--- a/arch/powerpc/mm/stab.c
+++ b/arch/powerpc/mm/stab.c
@@ -164,7 +164,7 @@ void switch_stab(struct task_struct *tsk, struct mm_struct *mm)
 {
 	struct stab_entry *stab = (struct stab_entry *) get_paca()->stab_addr;
 	struct stab_entry *ste;
-	unsigned long offset = __get_cpu_var(stab_cache_ptr);
+	unsigned long offset;
 	unsigned long pc = KSTK_EIP(tsk);
 	unsigned long stack = KSTK_ESP(tsk);
 	unsigned long unmapped_base;
@@ -172,6 +172,15 @@ void switch_stab(struct task_struct *tsk, struct mm_struct *mm)
 	/* Force previous translations to complete. DRENG */
 	asm volatile("isync" : : : "memory");
 
+	/*
+	 * We need interrupts hard-disabled here, not just soft-disabled,
+	 * so that a PMU interrupt can't occur, which might try to access
+	 * user memory (to get a stack trace) and possible cause an STAB miss
+	 * which would update the stab_cache/stab_cache_ptr per-cpu variables.
+	 */
+	hard_irq_disable();
+
+	offset = __get_cpu_var(stab_cache_ptr);
 	if (offset <= NR_STAB_CACHE_ENTRIES) {
 		int i;