powerpc/eeh: pseries platform EEH wait PE state

On pSeries platform, the PE state might be temporarily unavailable.
In that case, the firmware will return the corresponding wait time.
That means the kernel has to wait for appropriate time in order to
get the PE state.

The patch does the implementation for that. Besides, the function
has been abstracted through struct eeh_ops::wait_state so that EEH core
components could support multiple platforms in future.

Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

1 files changed, 2 insertions, 44 deletions

diff --git a/arch/powerpc/platforms/pseries/eeh.c b/arch/powerpc/platforms/pseries/eeh.c
index 8d11f1f1732..b5b03d41fb4 100644
--- a/arch/powerpc/platforms/pseries/eeh.c
+++ b/arch/powerpc/platforms/pseries/eeh.c
@@ -287,48 +287,6 @@ void eeh_slot_error_detail(struct pci_dn *pdn, int severity)
 }
 
 /**
- * eeh_wait_for_slot_status - Returns error status of slot
- * @pdn: pci device node
- * @max_wait_msecs: maximum number to millisecs to wait
- *
- * Return negative value if a permanent error, else return
- * Partition Endpoint (PE) status value.
- *
- * If @max_wait_msecs is positive, then this routine will
- * sleep until a valid status can be obtained, or until
- * the max allowed wait time is exceeded, in which case
- * a -2 is returned.
- */
-int eeh_wait_for_slot_status(struct pci_dn *pdn, int max_wait_msecs)
-{
-	int rc;
-	int mwait;
-
-	while (1) {
-		rc = eeh_ops->get_state(pdn->node, &mwait);
-		if (rc != EEH_STATE_UNAVAILABLE)
-			return rc;
-
-		if (max_wait_msecs <= 0) break;
-
-		if (mwait <= 0) {
-			printk(KERN_WARNING "EEH: Firmware returned bad wait value=%d\n",
-				mwait);
-			mwait = 1000;
-		} else if (mwait > 300*1000) {
-			printk(KERN_WARNING "EEH: Firmware is taking too long, time=%d\n",
-				mwait);
-			mwait = 300*1000;
-		}
-		max_wait_msecs -= mwait;
-		msleep(mwait);
-	}
-
-	printk(KERN_WARNING "EEH: Timed out waiting for slot status\n");
-	return -2;
-}
-
-/**
  * eeh_token_to_phys - Convert EEH address token to phys address
  * @token: I/O token, should be address in the form 0xA....
  *
@@ -640,7 +598,7 @@ int eeh_pci_enable(struct pci_dn *pdn, int function)
 		printk(KERN_WARNING "EEH: Unexpected state change %d, err=%d dn=%s\n",
 		        function, rc, pdn->node->full_name);
 
-	rc = eeh_wait_for_slot_status(pdn, PCI_BUS_RESET_WAIT_MSEC);
+	rc = eeh_ops->wait_state(pdn->node, PCI_BUS_RESET_WAIT_MSEC);
 	if (rc > 0 && (rc & EEH_STATE_MMIO_ENABLED) &&
 	   (function == EEH_OPT_THAW_MMIO))
 		return 0;
@@ -838,7 +796,7 @@ int eeh_reset_pe(struct pci_dn *pdn)
 	for (i=0; i<3; i++) {
 		eeh_reset_pe_once(pdn);
 
-		rc = eeh_wait_for_slot_status(pdn, PCI_BUS_RESET_WAIT_MSEC);
+		rc = eeh_ops->wait_state(pdn->node, PCI_BUS_RESET_WAIT_MSEC);
 		if (rc == (EEH_STATE_MMIO_ACTIVE | EEH_STATE_DMA_ACTIVE))
 			return 0;