[POWERPC] Remove the dregs of APUS support from arch/powerpc

APUS (the Amiga Power-Up System) is not supported under arch/powerpc
and it's unlikely it ever will be.  Therefore, this patch removes the
fragments of APUS support code from arch/powerpc which have been
copied from arch/ppc.

A few APUS references are left in asm-powerpc in .h files which are
still used from arch/ppc.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

2 files changed, 0 insertions, 137 deletions

diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index 361acfa2894..d6c475ca311 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -16,13 +16,6 @@ config EMBEDDED6xx
 	bool "Embedded 6xx/7xx/7xxx-based board"
 	depends on PPC32 && (BROKEN||BROKEN_ON_SMP)
 
-config APUS
-	bool "Amiga-APUS"
-	depends on PPC32 && BROKEN
-	help
-	  Select APUS if configuring for a PowerUP Amiga.
-	  More information is available at:
-	  <http://linux-apus.sourceforge.net/>.
 endchoice
 
 source "arch/powerpc/platforms/pseries/Kconfig"
diff --git a/arch/powerpc/platforms/apus/Kconfig b/arch/powerpc/platforms/apus/Kconfig
deleted file mode 100644
index 6bde3bffed8..00000000000
--- a/arch/powerpc/platforms/apus/Kconfig
+++ /dev/null
@@ -1,130 +0,0 @@
-
-config AMIGA
-	bool
-	depends on APUS
-	default y
-	help
-	  This option enables support for the Amiga series of computers.
-
-config ZORRO
-	bool
-	depends on APUS
-	default y
-	help
-	  This enables support for the Zorro bus in the Amiga. If you have
-	  expansion cards in your Amiga that conform to the Amiga
-	  AutoConfig(tm) specification, say Y, otherwise N. Note that even
-	  expansion cards that do not fit in the Zorro slots but fit in e.g.
-	  the CPU slot may fall in this category, so you have to say Y to let
-	  Linux use these.
-
-config ABSTRACT_CONSOLE
-	bool
-	depends on APUS
-	default y
-
-config APUS_FAST_EXCEPT
-	bool
-	depends on APUS
-	default y
-
-config AMIGA_PCMCIA
-	bool "Amiga 1200/600 PCMCIA support"
-	depends on APUS && EXPERIMENTAL
-	help
-	  Include support in the kernel for pcmcia on Amiga 1200 and Amiga
-	  600. If you intend to use pcmcia cards say Y; otherwise say N.
-
-config AMIGA_BUILTIN_SERIAL
-	tristate "Amiga builtin serial support"
-	depends on APUS
-	help
-	  If you want to use your Amiga's built-in serial port in Linux,
-	  answer Y.
-
-	  To compile this driver as a module, choose M here.
-
-config GVPIOEXT
-	tristate "GVP IO-Extender support"
-	depends on APUS
-	help
-	  If you want to use a GVP IO-Extender serial card in Linux, say Y.
-	  Otherwise, say N.
-
-config GVPIOEXT_LP
-	tristate "GVP IO-Extender parallel printer support"
-	depends on GVPIOEXT
-	help
-	  Say Y to enable driving a printer from the parallel port on your
-	  GVP IO-Extender card, N otherwise.
-
-config GVPIOEXT_PLIP
-	tristate "GVP IO-Extender PLIP support"
-	depends on GVPIOEXT
-	help
-	  Say Y to enable doing IP over the parallel port on your GVP
-	  IO-Extender card, N otherwise.
-
-config MULTIFACE_III_TTY
-	tristate "Multiface Card III serial support"
-	depends on APUS
-	help
-	  If you want to use a Multiface III card's serial port in Linux,
-	  answer Y.
-
-	  To compile this driver as a module, choose M here.
-
-config A2232
-	tristate "Commodore A2232 serial support (EXPERIMENTAL)"
-	depends on EXPERIMENTAL && APUS
-	---help---
-	  This option supports the 2232 7-port serial card shipped with the
-	  Amiga 2000 and other Zorro-bus machines, dating from 1989.  At
-	  a max of 19,200 bps, the ports are served by a 6551 ACIA UART chip
-	  each, plus a 8520 CIA, and a master 6502 CPU and buffer as well. The
-	  ports were connected with 8 pin DIN connectors on the card bracket,
-	  for which 8 pin to DB25 adapters were supplied. The card also had
-	  jumpers internally to toggle various pinning configurations.
-
-	  This driver can be built as a module; but then "generic_serial"
-	  will also be built as a module. This has to be loaded before
-	  "ser_a2232". If you want to do this, answer M here.
-
-config WHIPPET_SERIAL
-	tristate "Hisoft Whippet PCMCIA serial support"
-	depends on AMIGA_PCMCIA
-	help
-	  HiSoft has a web page at <http://www.hisoft.co.uk/>, but there
-	  is no listing for the Whippet in their Amiga section.
-
-config APNE
-	tristate "PCMCIA NE2000 support"
-	depends on AMIGA_PCMCIA
-	help
-	  If you have a PCMCIA NE2000 compatible adapter, say Y.  Otherwise,
-	  say N.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called apne.
-
-config SERIAL_CONSOLE
-	bool "Support for serial port console"
-	depends on APUS && (AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y)
-
-config HEARTBEAT
-	bool "Use power LED as a heartbeat"
-	depends on APUS
-	help
-	  Use the power-on LED on your machine as a load meter.  The exact
-	  behavior is platform-dependent, but normally the flash frequency is
-	  a hyperbolic function of the 5-minute load average.
-
-config PROC_HARDWARE
-	bool "/proc/hardware support"
-	depends on APUS
-
-source "drivers/zorro/Kconfig"
-
-config PCI_PERMEDIA
-	bool "PCI for Permedia2"
-	depends on !4xx && !8xx && APUS