powerpc: Remove arch/ppc and include/asm-ppc

All the maintained platforms are now in arch/powerpc, so the old
arch/ppc stuff can now go away.

Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: John Linn <john.linn@xilinx.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

6 files changed, 0 insertions, 4283 deletions

diff --git a/arch/ppc/8xx_io/Kconfig b/arch/ppc/8xx_io/Kconfig
deleted file mode 100644
index c623e44f01a..00000000000
--- a/arch/ppc/8xx_io/Kconfig
+++ /dev/null
@@ -1,134 +0,0 @@
-#
-# MPC8xx Communication options
-#
-
-menu "MPC8xx CPM Options"
-	depends on 8xx
-
-config SCC_ENET
-	bool "CPM SCC Ethernet"
-	depends on NET_ETHERNET
-	help
-	  Enable Ethernet support via the Motorola MPC8xx serial
-	  communications controller.
-
-choice
-	prompt "SCC used for Ethernet"
-	depends on SCC_ENET
-	default SCC1_ENET
-
-config SCC1_ENET
-	bool "SCC1"
-	help
-	  Use MPC8xx serial communications controller 1 to drive Ethernet
-	  (default).
-
-config SCC2_ENET
-	bool "SCC2"
-	help
-	  Use MPC8xx serial communications controller 2 to drive Ethernet.
-
-config SCC3_ENET
-	bool "SCC3"
-	help
-	  Use MPC8xx serial communications controller 3 to drive Ethernet.
-
-endchoice
-
-config FEC_ENET
-	bool "860T FEC Ethernet"
-	depends on NET_ETHERNET
-	help
-	  Enable Ethernet support via the Fast Ethernet Controller (FCC) on
-	  the Motorola MPC8260.
-
-config USE_MDIO
-	bool "Use MDIO for PHY configuration"
-	depends on FEC_ENET
-	help
-	  On some boards the hardware configuration of the ethernet PHY can be
-	  used without any software interaction over the MDIO interface, so
-	  all MII code can be omitted. Say N here if unsure or if you don't
-	  need link status reports.
-
-config  FEC_AM79C874
-	bool "Support AMD79C874 PHY"
-	depends on USE_MDIO
-
-config FEC_LXT970
-	bool "Support LXT970 PHY"
-	depends on USE_MDIO
-
-config FEC_LXT971
-	bool "Support LXT971 PHY"
-	depends on USE_MDIO
-	
-config FEC_QS6612
-	bool "Support QS6612 PHY"
-	depends on USE_MDIO
-	
-config ENET_BIG_BUFFERS
-	bool "Use Big CPM Ethernet Buffers"
-	depends on SCC_ENET || FEC_ENET
-	help
-	  Allocate large buffers for MPC8xx Ethernet. Increases throughput
-	  and decreases the likelihood of dropped packets, but costs memory.
-
-# This doesn't really belong here, but it is convenient to ask
-# 8xx specific questions.
-comment "Generic MPC8xx Options"
-
-config 8xx_COPYBACK
-	bool "Copy-Back Data Cache (else Writethrough)"
-	help
-	  Saying Y here will cause the cache on an MPC8xx processor to be used
-	  in Copy-Back mode.  If you say N here, it is used in Writethrough
-	  mode.
-
-	  If in doubt, say Y here.
-
-config 8xx_CPU6
-	bool "CPU6 Silicon Errata (860 Pre Rev. C)"
-	help
-	  MPC860 CPUs, prior to Rev C have some bugs in the silicon, which
-	  require workarounds for Linux (and most other OSes to work).  If you
-	  get a BUG() very early in boot, this might fix the problem.  For
-	  more details read the document entitled "MPC860 Family Device Errata
-	  Reference" on Motorola's website.  This option also incurs a
-	  performance hit.
-
-	  If in doubt, say N here.
-
-choice
-	prompt "Microcode patch selection"
-	default NO_UCODE_PATCH
-	help
-	  Help not implemented yet, coming soon.
-
-config NO_UCODE_PATCH
-	bool "None"
-
-config USB_SOF_UCODE_PATCH
-	bool "USB SOF patch"
-	help
-	  Help not implemented yet, coming soon.
-
-config I2C_SPI_UCODE_PATCH
-	bool "I2C/SPI relocation patch"
-	help
-	  Help not implemented yet, coming soon.
-
-config I2C_SPI_SMC1_UCODE_PATCH
-	bool "I2C/SPI/SMC1 relocation patch"
-	help
-	  Help not implemented yet, coming soon.
-
-endchoice
-
-config UCODE_PATCH
-	bool
-	default y
-	depends on !NO_UCODE_PATCH
-
-endmenu
-
diff --git a/arch/ppc/8xx_io/Makefile b/arch/ppc/8xx_io/Makefile
deleted file mode 100644
index 1051a06df7e..00000000000
--- a/arch/ppc/8xx_io/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# Makefile for the linux MPC8xx ppc-specific parts of comm processor
-#
-
-obj-y			:= commproc.o
-
-obj-$(CONFIG_FEC_ENET)	+= fec.o
-obj-$(CONFIG_SCC_ENET)	+= enet.o
-obj-$(CONFIG_UCODE_PATCH) += micropatch.o
diff --git a/arch/ppc/8xx_io/commproc.c b/arch/ppc/8xx_io/commproc.c
deleted file mode 100644
index 752443df5ec..00000000000
--- a/arch/ppc/8xx_io/commproc.c
+++ /dev/null
@@ -1,432 +0,0 @@
-/*
- * General Purpose functions for the global management of the
- * Communication Processor Module.
- * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
- *
- * In addition to the individual control of the communication
- * channels, there are a few functions that globally affect the
- * communication processor.
- *
- * Buffer descriptors must be allocated from the dual ported memory
- * space.  The allocator for that is here.  When the communication
- * process is reset, we reclaim the memory available.  There is
- * currently no deallocator for this memory.
- * The amount of space available is platform dependent.  On the
- * MBX, the EPPC software loads additional microcode into the
- * communication processor, and uses some of the DP ram for this
- * purpose.  Current, the first 512 bytes and the last 256 bytes of
- * memory are used.  Right now I am conservative and only use the
- * memory that can never be used for microcode.  If there are
- * applications that require more DP ram, we can expand the boundaries
- * but then we have to be careful of any downloaded microcode.
- */
-#include <linux/errno.h>
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/dma-mapping.h>
-#include <linux/param.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/module.h>
-#include <asm/mpc8xx.h>
-#include <asm/page.h>
-#include <asm/pgtable.h>
-#include <asm/8xx_immap.h>
-#include <asm/cpm1.h>
-#include <asm/io.h>
-#include <asm/tlbflush.h>
-#include <asm/rheap.h>
-
-#define immr_map(member)						\
-({									\
-	u32 offset = offsetof(immap_t, member);				\
-	void *addr = ioremap (IMAP_ADDR + offset,			\
-			      FIELD_SIZEOF(immap_t, member));		\
-	addr;								\
-})
-
-#define immr_map_size(member, size)					\
-({									\
-	u32 offset = offsetof(immap_t, member);				\
-	void *addr = ioremap (IMAP_ADDR + offset, size);		\
-	addr;								\
-})
-
-static void m8xx_cpm_dpinit(void);
-cpm8xx_t	*cpmp;		/* Pointer to comm processor space */
-
-/* CPM interrupt vector functions.
-*/
-struct	cpm_action {
-	void	(*handler)(void *);
-	void	*dev_id;
-};
-static	struct	cpm_action cpm_vecs[CPMVEC_NR];
-static	irqreturn_t cpm_interrupt(int irq, void * dev);
-static	irqreturn_t cpm_error_interrupt(int irq, void *dev);
-/* Define a table of names to identify CPM interrupt handlers in
- * /proc/interrupts.
- */
-const char *cpm_int_name[] =
-	{ "error",	"PC4",		"PC5",		"SMC2",
-	  "SMC1",	"SPI",		"PC6",		"Timer 4",
-	  "",		"PC7",		"PC8",		"PC9",
-	  "Timer 3",	"",		"PC10",		"PC11",
-	  "I2C",	"RISC Timer",	"Timer 2",	"",
-	  "IDMA2",	"IDMA1",	"SDMA error",	"PC12",
-	  "PC13",	"Timer 1",	"PC14",		"SCC4",
-	  "SCC3",	"SCC2",		"SCC1",		"PC15"
-	};
-
-static void
-cpm_mask_irq(unsigned int irq)
-{
-	int cpm_vec = irq - CPM_IRQ_OFFSET;
-
-	clrbits32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, (1 << cpm_vec));
-}
-
-static void
-cpm_unmask_irq(unsigned int irq)
-{
-	int cpm_vec = irq - CPM_IRQ_OFFSET;
-
-	setbits32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, (1 << cpm_vec));
-}
-
-static void
-cpm_ack(unsigned int irq)
-{
-	/* We do not need to do anything here. */
-}
-
-static void
-cpm_eoi(unsigned int irq)
-{
-	int cpm_vec = irq - CPM_IRQ_OFFSET;
-
-	out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cisr, (1 << cpm_vec));
-}
-
-struct hw_interrupt_type cpm_pic = {
-	.typename	= " CPM      ",
-	.enable		= cpm_unmask_irq,
-	.disable	= cpm_mask_irq,
-	.ack		= cpm_ack,
-	.end		= cpm_eoi,
-};
-
-void
-m8xx_cpm_reset(void)
-{
-	volatile immap_t	 *imp;
-	volatile cpm8xx_t	*commproc;
-
-	imp = (immap_t *)IMAP_ADDR;
-	commproc = (cpm8xx_t *)&imp->im_cpm;
-
-#ifdef CONFIG_UCODE_PATCH
-	/* Perform a reset.
-	*/
-	commproc->cp_cpcr = (CPM_CR_RST | CPM_CR_FLG);
-
-	/* Wait for it.
-	*/
-	while (commproc->cp_cpcr & CPM_CR_FLG);
-
-	cpm_load_patch(imp);
-#endif
-
-	/* Set SDMA Bus Request priority 5.
-	 * On 860T, this also enables FEC priority 6.  I am not sure
-	 * this is what we really want for some applications, but the
-	 * manual recommends it.
-	 * Bit 25, FAM can also be set to use FEC aggressive mode (860T).
-	 */
-	out_be32(&imp->im_siu_conf.sc_sdcr, 1),
-
-	/* Reclaim the DP memory for our use. */
-	m8xx_cpm_dpinit();
-
-	/* Tell everyone where the comm processor resides.
-	*/
-	cpmp = (cpm8xx_t *)commproc;
-}
-
-/* This is called during init_IRQ.  We used to do it above, but this
- * was too early since init_IRQ was not yet called.
- */
-static struct irqaction cpm_error_irqaction = {
-	.handler = cpm_error_interrupt,
-	.mask = CPU_MASK_NONE,
-};
-static struct irqaction cpm_interrupt_irqaction = {
-	.handler = cpm_interrupt,
-	.mask = CPU_MASK_NONE,
-	.name = "CPM cascade",
-};
-
-void
-cpm_interrupt_init(void)
-{
-	int i;
-
-	/* Initialize the CPM interrupt controller.
-	*/
-	out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr,
-	    (CICR_SCD_SCC4 | CICR_SCC_SCC3 | CICR_SCB_SCC2 | CICR_SCA_SCC1) |
-		((CPM_INTERRUPT/2) << 13) | CICR_HP_MASK);
-	out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, 0);
-
-        /* install the CPM interrupt controller routines for the CPM
-         * interrupt vectors
-         */
-        for ( i = CPM_IRQ_OFFSET ; i < CPM_IRQ_OFFSET + NR_CPM_INTS ; i++ )
-                irq_desc[i].chip = &cpm_pic;
-
-	/* Set our interrupt handler with the core CPU.	*/
-	if (setup_irq(CPM_INTERRUPT, &cpm_interrupt_irqaction))
-		panic("Could not allocate CPM IRQ!");
-
-	/* Install our own error handler. */
-	cpm_error_irqaction.name = cpm_int_name[CPMVEC_ERROR];
-	if (setup_irq(CPM_IRQ_OFFSET + CPMVEC_ERROR, &cpm_error_irqaction))
-		panic("Could not allocate CPM error IRQ!");
-
-	setbits32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr, CICR_IEN);
-}
-
-/*
- * Get the CPM interrupt vector.
- */
-int
-cpm_get_irq(void)
-{
-	int cpm_vec;
-
-	/* Get the vector by setting the ACK bit and then reading
-	 * the register.
-	 */
-	out_be16(&((volatile immap_t *)IMAP_ADDR)->im_cpic.cpic_civr, 1);
-	cpm_vec = in_be16(&((volatile immap_t *)IMAP_ADDR)->im_cpic.cpic_civr);
-	cpm_vec >>= 11;
-
-	return cpm_vec;
-}
-
-/* CPM interrupt controller cascade interrupt.
-*/
-static	irqreturn_t
-cpm_interrupt(int irq, void * dev)
-{
-	/* This interrupt handler never actually gets called.  It is
-	 * installed only to unmask the CPM cascade interrupt in the SIU
-	 * and to make the CPM cascade interrupt visible in /proc/interrupts.
-	 */
-	return IRQ_HANDLED;
-}
-
-/* The CPM can generate the error interrupt when there is a race condition
- * between generating and masking interrupts.  All we have to do is ACK it
- * and return.  This is a no-op function so we don't need any special
- * tests in the interrupt handler.
- */
-static	irqreturn_t
-cpm_error_interrupt(int irq, void *dev)
-{
-	return IRQ_HANDLED;
-}
-
-/* A helper function to translate the handler prototype required by
- * request_irq() to the handler prototype required by cpm_install_handler().
- */
-static irqreturn_t
-cpm_handler_helper(int irq, void *dev_id)
-{
-	int cpm_vec = irq - CPM_IRQ_OFFSET;
-
-	(*cpm_vecs[cpm_vec].handler)(dev_id);
-
-	return IRQ_HANDLED;
-}
-
-/* Install a CPM interrupt handler.
- * This routine accepts a CPM interrupt vector in the range 0 to 31.
- * This routine is retained for backward compatibility.  Rather than using
- * this routine to install a CPM interrupt handler, you can now use
- * request_irq() with an IRQ in the range CPM_IRQ_OFFSET to
- * CPM_IRQ_OFFSET + NR_CPM_INTS - 1 (16 to 47).
- *
- * Notice that the prototype of the interrupt handler function must be
- * different depending on whether you install the handler with
- * request_irq() or cpm_install_handler().
- */
-void
-cpm_install_handler(int cpm_vec, void (*handler)(void *), void *dev_id)
-{
-	int err;
-
-	/* If null handler, assume we are trying to free the IRQ.
-	*/
-	if (!handler) {
-		free_irq(CPM_IRQ_OFFSET + cpm_vec, dev_id);
-		return;
-	}
-
-	if (cpm_vecs[cpm_vec].handler != 0)
-		printk(KERN_INFO "CPM interrupt %x replacing %x\n",
-			(uint)handler, (uint)cpm_vecs[cpm_vec].handler);
-	cpm_vecs[cpm_vec].handler = handler;
-	cpm_vecs[cpm_vec].dev_id = dev_id;
-
-	if ((err = request_irq(CPM_IRQ_OFFSET + cpm_vec, cpm_handler_helper,
-					0, cpm_int_name[cpm_vec], dev_id)))
-		printk(KERN_ERR "request_irq() returned %d for CPM vector %d\n",
-				err, cpm_vec);
-}
-
-/* Free a CPM interrupt handler.
- * This routine accepts a CPM interrupt vector in the range 0 to 31.
- * This routine is retained for backward compatibility.
- */
-void
-cpm_free_handler(int cpm_vec)
-{
-	request_irq(CPM_IRQ_OFFSET + cpm_vec, NULL, 0, 0,
-		cpm_vecs[cpm_vec].dev_id);
-
-	cpm_vecs[cpm_vec].handler = NULL;
-	cpm_vecs[cpm_vec].dev_id = NULL;
-}
-
-/* Set a baud rate generator.  This needs lots of work.  There are
- * four BRGs, any of which can be wired to any channel.
- * The internal baud rate clock is the system clock divided by 16.
- * This assumes the baudrate is 16x oversampled by the uart.
- */
-#define BRG_INT_CLK		(((bd_t *)__res)->bi_intfreq)
-#define BRG_UART_CLK		(BRG_INT_CLK/16)
-#define BRG_UART_CLK_DIV16	(BRG_UART_CLK/16)
-
-void
-cpm_setbrg(uint brg, uint rate)
-{
-	volatile uint	*bp;
-
-	/* This is good enough to get SMCs running.....
-	*/
-	bp = (uint *)&cpmp->cp_brgc1;
-	bp += brg;
-	/* The BRG has a 12-bit counter.  For really slow baud rates (or
-	 * really fast processors), we may have to further divide by 16.
-	 */
-	if (((BRG_UART_CLK / rate) - 1) < 4096)
-		*bp = (((BRG_UART_CLK / rate) - 1) << 1) | CPM_BRG_EN;
-	else
-		*bp = (((BRG_UART_CLK_DIV16 / rate) - 1) << 1) |
-						CPM_BRG_EN | CPM_BRG_DIV16;
-}
-
-/*
- * dpalloc / dpfree bits.
- */
-static spinlock_t cpm_dpmem_lock;
-/*
- * 16 blocks should be enough to satisfy all requests
- * until the memory subsystem goes up...
- */
-static rh_block_t cpm_boot_dpmem_rh_block[16];
-static rh_info_t cpm_dpmem_info;
-
-#define CPM_DPMEM_ALIGNMENT	8
-static u8* dpram_vbase;
-static uint dpram_pbase;
-
-void m8xx_cpm_dpinit(void)
-{
-	spin_lock_init(&cpm_dpmem_lock);
-
-	dpram_vbase = immr_map_size(im_cpm.cp_dpmem, CPM_DATAONLY_BASE + CPM_DATAONLY_SIZE);
-	dpram_pbase = (uint)&((immap_t *)IMAP_ADDR)->im_cpm.cp_dpmem;
-
-	/* Initialize the info header */
-	rh_init(&cpm_dpmem_info, CPM_DPMEM_ALIGNMENT,
-			sizeof(cpm_boot_dpmem_rh_block) /
-			sizeof(cpm_boot_dpmem_rh_block[0]),
-			cpm_boot_dpmem_rh_block);
-
-	/*
-	 * Attach the usable dpmem area.
-	 * XXX: This is actually crap.  CPM_DATAONLY_BASE and
-	 * CPM_DATAONLY_SIZE are a subset of the available dparm.  It varies
-	 * with the processor and the microcode patches applied / activated.
-	 * But the following should be at least safe.
-	 */
-	rh_attach_region(&cpm_dpmem_info, CPM_DATAONLY_BASE, CPM_DATAONLY_SIZE);
-}
-
-/*
- * Allocate the requested size worth of DP memory.
- * This function returns an offset into the DPRAM area.
- * Use cpm_dpram_addr() to get the virtual address of the area.
- */
-unsigned long cpm_dpalloc(uint size, uint align)
-{
-	unsigned long start;
-	unsigned long flags;
-
-	spin_lock_irqsave(&cpm_dpmem_lock, flags);
-	cpm_dpmem_info.alignment = align;
-	start = rh_alloc(&cpm_dpmem_info, size, "commproc");
-	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
-	return start;
-}
-EXPORT_SYMBOL(cpm_dpalloc);
-
-int cpm_dpfree(unsigned long offset)
-{
-	int ret;
-	unsigned long flags;
-
-	spin_lock_irqsave(&cpm_dpmem_lock, flags);
-	ret = rh_free(&cpm_dpmem_info, offset);
-	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
-	return ret;
-}
-EXPORT_SYMBOL(cpm_dpfree);
-
-unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align)
-{
-	unsigned long start;
-	unsigned long flags;
-
-	spin_lock_irqsave(&cpm_dpmem_lock, flags);
-	cpm_dpmem_info.alignment = align;
-	start = rh_alloc_fixed(&cpm_dpmem_info, offset, size, "commproc");
-	spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
-	return start;
-}
-EXPORT_SYMBOL(cpm_dpalloc_fixed);
-
-void cpm_dpdump(void)
-{
-	rh_dump(&cpm_dpmem_info);
-}
-EXPORT_SYMBOL(cpm_dpdump);
-
-void *cpm_dpram_addr(unsigned long offset)
-{
-	return (void *)(dpram_vbase + offset);
-}
-EXPORT_SYMBOL(cpm_dpram_addr);
-
-uint cpm_dpram_phys(u8* addr)
-{
-	return (dpram_pbase + (uint)(addr - dpram_vbase));
-}
-EXPORT_SYMBOL(cpm_dpram_phys);
diff --git a/arch/ppc/8xx_io/enet.c b/arch/ppc/8xx_io/enet.c
deleted file mode 100644
index 5899aea1644..00000000000
--- a/arch/ppc/8xx_io/enet.c
+++ /dev/null
@@ -1,982 +0,0 @@
-/*
- * Ethernet driver for Motorola MPC8xx.
- * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
- *
- * I copied the basic skeleton from the lance driver, because I did not
- * know how to write the Linux driver, but I did know how the LANCE worked.
- *
- * This version of the driver is somewhat selectable for the different
- * processor/board combinations.  It works for the boards I know about
- * now, and should be easily modified to include others.  Some of the
- * configuration information is contained in <asm/cpm1.h> and the
- * remainder is here.
- *
- * Buffer descriptors are kept in the CPM dual port RAM, and the frame
- * buffers are in the host memory.
- *
- * Right now, I am very watseful with the buffers.  I allocate memory
- * pages and then divide them into 2K frame buffers.  This way I know I
- * have buffers large enough to hold one frame within one buffer descriptor.
- * Once I get this working, I will use 64 or 128 byte CPM buffers, which
- * will be much more memory efficient and will easily handle lots of
- * small packets.
- *
- */
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/ptrace.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/dma-mapping.h>
-#include <linux/bitops.h>
-
-#include <asm/8xx_immap.h>
-#include <asm/pgtable.h>
-#include <asm/mpc8xx.h>
-#include <asm/uaccess.h>
-#include <asm/cpm1.h>
-#include <asm/cacheflush.h>
-
-/*
- *				Theory of Operation
- *
- * The MPC8xx CPM performs the Ethernet processing on SCC1.  It can use
- * an aribtrary number of buffers on byte boundaries, but must have at
- * least two receive buffers to prevent constant overrun conditions.
- *
- * The buffer descriptors are allocated from the CPM dual port memory
- * with the data buffers allocated from host memory, just like all other
- * serial communication protocols.  The host memory buffers are allocated
- * from the free page pool, and then divided into smaller receive and
- * transmit buffers.  The size of the buffers should be a power of two,
- * since that nicely divides the page.  This creates a ring buffer
- * structure similar to the LANCE and other controllers.
- *
- * Like the LANCE driver:
- * The driver runs as two independent, single-threaded flows of control.  One
- * is the send-packet routine, which enforces single-threaded use by the
- * cep->tx_busy flag.  The other thread is the interrupt handler, which is
- * single threaded by the hardware and other software.
- *
- * The send packet thread has partial control over the Tx ring and the
- * 'cep->tx_busy' flag.  It sets the tx_busy flag whenever it's queuing a Tx
- * packet. If the next queue slot is empty, it clears the tx_busy flag when
- * finished otherwise it sets the 'lp->tx_full' flag.
- *
- * The MBX has a control register external to the MPC8xx that has some
- * control of the Ethernet interface.  Information is in the manual for
- * your board.
- *
- * The RPX boards have an external control/status register.  Consult the
- * programming documents for details unique to your board.
- *
- * For the TQM8xx(L) modules, there is no control register interface.
- * All functions are directly controlled using I/O pins.  See <asm/cpm1.h>.
- */
-
-/* The transmitter timeout
- */
-#define TX_TIMEOUT	(2*HZ)
-
-/* The number of Tx and Rx buffers.  These are allocated from the page
- * pool.  The code may assume these are power of two, so it is best
- * to keep them that size.
- * We don't need to allocate pages for the transmitter.  We just use
- * the skbuffer directly.
- */
-#ifdef CONFIG_ENET_BIG_BUFFERS
-#define CPM_ENET_RX_PAGES	32
-#define CPM_ENET_RX_FRSIZE	2048
-#define CPM_ENET_RX_FRPPG	(PAGE_SIZE / CPM_ENET_RX_FRSIZE)
-#define RX_RING_SIZE		(CPM_ENET_RX_FRPPG * CPM_ENET_RX_PAGES)
-#define TX_RING_SIZE		64	/* Must be power of two */
-#define TX_RING_MOD_MASK	63	/*   for this to work */
-#else
-#define CPM_ENET_RX_PAGES	4
-#define CPM_ENET_RX_FRSIZE	2048
-#define CPM_ENET_RX_FRPPG	(PAGE_SIZE / CPM_ENET_RX_FRSIZE)
-#define RX_RING_SIZE		(CPM_ENET_RX_FRPPG * CPM_ENET_RX_PAGES)
-#define TX_RING_SIZE		8	/* Must be power of two */
-#define TX_RING_MOD_MASK	7	/*   for this to work */
-#endif
-
-/* The CPM stores dest/src/type, data, and checksum for receive packets.
- */
-#define PKT_MAXBUF_SIZE		1518
-#define PKT_MINBUF_SIZE		64
-#define PKT_MAXBLR_SIZE		1520
-
-/* The CPM buffer descriptors track the ring buffers.  The rx_bd_base and
- * tx_bd_base always point to the base of the buffer descriptors.  The
- * cur_rx and cur_tx point to the currently available buffer.
- * The dirty_tx tracks the current buffer that is being sent by the
- * controller.  The cur_tx and dirty_tx are equal under both completely
- * empty and completely full conditions.  The empty/ready indicator in
- * the buffer descriptor determines the actual condition.
- */
-struct scc_enet_private {
-	/* The saved address of a sent-in-place packet/buffer, for skfree(). */
-	struct	sk_buff* tx_skbuff[TX_RING_SIZE];
-	ushort	skb_cur;
-	ushort	skb_dirty;
-
-	/* CPM dual port RAM relative addresses.
-	*/
-	cbd_t	*rx_bd_base;		/* Address of Rx and Tx buffers. */
-	cbd_t	*tx_bd_base;
-	cbd_t	*cur_rx, *cur_tx;		/* The next free ring entry */
-	cbd_t	*dirty_tx;	/* The ring entries to be free()ed. */
-	scc_t	*sccp;
-
-	/* Virtual addresses for the receive buffers because we can't
-	 * do a __va() on them anymore.
-	 */
-	unsigned char *rx_vaddr[RX_RING_SIZE];
-	struct	net_device_stats stats;
-	uint	tx_full;
-	spinlock_t lock;
-};
-
-static int scc_enet_open(struct net_device *dev);
-static int scc_enet_start_xmit(struct sk_buff *skb, struct net_device *dev);
-static int scc_enet_rx(struct net_device *dev);
-static void scc_enet_interrupt(void *dev_id);
-static int scc_enet_close(struct net_device *dev);
-static struct net_device_stats *scc_enet_get_stats(struct net_device *dev);
-static void set_multicast_list(struct net_device *dev);
-
-/* Get this from various configuration locations (depends on board).
-*/
-/*static	ushort	my_enet_addr[] = { 0x0800, 0x3e26, 0x1559 };*/
-
-/* Typically, 860(T) boards use SCC1 for Ethernet, and other 8xx boards
- * use SCC2. Some even may use SCC3.
- * This is easily extended if necessary.
- */
-#if defined(CONFIG_SCC3_ENET)
-#define CPM_CR_ENET	CPM_CR_CH_SCC3
-#define PROFF_ENET	PROFF_SCC3
-#define SCC_ENET	2		/* Index, not number! */
-#define CPMVEC_ENET	CPMVEC_SCC3
-#elif defined(CONFIG_SCC2_ENET)
-#define CPM_CR_ENET	CPM_CR_CH_SCC2
-#define PROFF_ENET	PROFF_SCC2
-#define SCC_ENET	1		/* Index, not number! */
-#define CPMVEC_ENET	CPMVEC_SCC2
-#elif defined(CONFIG_SCC1_ENET)
-#define CPM_CR_ENET	CPM_CR_CH_SCC1
-#define PROFF_ENET	PROFF_SCC1
-#define SCC_ENET	0		/* Index, not number! */
-#define CPMVEC_ENET	CPMVEC_SCC1
-#else
-#error CONFIG_SCCx_ENET not defined
-#endif
-
-static int
-scc_enet_open(struct net_device *dev)
-{
-
-	/* I should reset the ring buffers here, but I don't yet know
-	 * a simple way to do that.
-	 */
-
-	netif_start_queue(dev);
-	return 0;					/* Always succeed */
-}
-
-static int
-scc_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
-{
-	struct scc_enet_private *cep = (struct scc_enet_private *)dev->priv;
-	volatile cbd_t	*bdp;
-
-	/* Fill in a Tx ring entry */
-	bdp = cep->cur_tx;
-
-#ifndef final_version
-	if (bdp->cbd_sc & BD_ENET_TX_READY) {
-		/* Ooops.  All transmit buffers are full.  Bail out.
-		 * This should not happen, since cep->tx_busy should be set.
-		 */
-		printk("%s: tx queue full!.\n", dev->name);
-		return 1;
-	}
-#endif
-
-	/* Clear all of the status flags.
-	 */
-	bdp->cbd_sc &= ~BD_ENET_TX_STATS;
-
-	/* If the frame is short, tell CPM to pad it.
-	*/
-	if (skb->len <= ETH_ZLEN)
-		bdp->cbd_sc |= BD_ENET_TX_PAD;
-	else
-		bdp->cbd_sc &= ~BD_ENET_TX_PAD;
-
-	/* Set buffer length and buffer pointer.
-	*/
-	bdp->cbd_datlen = skb->len;
-	bdp->cbd_bufaddr = __pa(skb->data);
-
-	/* Save skb pointer.
-	*/
-	cep->tx_skbuff[cep->skb_cur] = skb;
-
-	cep->stats.tx_bytes += skb->len;
-	cep->skb_cur = (cep->skb_cur+1) & TX_RING_MOD_MASK;
-
-	/* Push the data cache so the CPM does not get stale memory
-	 * data.
-	 */
-	flush_dcache_range((unsigned long)(skb->data),
-					(unsigned long)(skb->data + skb->len));
-
-	spin_lock_irq(&cep->lock);
-
-	/* Send it on its way.  Tell CPM its ready, interrupt when done,
-	 * its the last BD of the frame, and to put the CRC on the end.
-	 */
-	bdp->cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_INTR | BD_ENET_TX_LAST | BD_ENET_TX_TC);
-
-	dev->trans_start = jiffies;
-
-	/* If this was the last BD in the ring, start at the beginning again.
-	*/
-	if (bdp->cbd_sc & BD_ENET_TX_WRAP)
-		bdp = cep->tx_bd_base;
-	else
-		bdp++;
-
-	if (bdp->cbd_sc & BD_ENET_TX_READY) {
-		netif_stop_queue(dev);
-		cep->tx_full = 1;
-	}
-
-	cep->cur_tx = (cbd_t *)bdp;
-
-	spin_unlock_irq(&cep->lock);
-
-	return 0;
-}
-
-static void
-scc_enet_timeout(struct net_device *dev)
-{
-	struct scc_enet_private *cep = (struct scc_enet_private *)dev->priv;
-
-	printk("%s: transmit timed out.\n", dev->name);
-	cep->stats.tx_errors++;
-#ifndef final_version
-	{
-		int	i;
-		cbd_t	*bdp;
-		printk(" Ring data dump: cur_tx %p%s cur_rx %p.\n",
-		       cep->cur_tx, cep->tx_full ? " (full)" : "",
-		       cep->cur_rx);
-		bdp = cep->tx_bd_base;
-		for (i = 0 ; i < TX_RING_SIZE; i++, bdp++)
-			printk("%04x %04x %08x\n",
-			       bdp->cbd_sc,
-			       bdp->cbd_datlen,
-			       bdp->cbd_bufaddr);
-		bdp = cep->rx_bd_base;
-		for (i = 0 ; i < RX_RING_SIZE; i++, bdp++)
-			printk("%04x %04x %08x\n",
-			       bdp->cbd_sc,
-			       bdp->cbd_datlen,
-			       bdp->cbd_bufaddr);
-	}
-#endif
-	if (!cep->tx_full)
-		netif_wake_queue(dev);
-}
-
-/* The interrupt handler.
- * This is called from the CPM handler, not the MPC core interrupt.
- */
-static void
-scc_enet_interrupt(void *dev_id)
-{
-	struct	net_device *dev = dev_id;
-	volatile struct	scc_enet_private *cep;
-	volatile cbd_t	*bdp;
-	ushort	int_events;
-	int	must_restart;
-
-	cep = (struct scc_enet_private *)dev->priv;
-
-	/* Get the interrupt events that caused us to be here.
-	*/
-	int_events = cep->sccp->scc_scce;
-	cep->sccp->scc_scce = int_events;
-	must_restart = 0;
-
-	/* Handle receive event in its own function.
-	*/
-	if (int_events & SCCE_ENET_RXF)
-		scc_enet_rx(dev_id);
-
-	/* Check for a transmit error.  The manual is a little unclear
-	 * about this, so the debug code until I get it figured out.  It
-	 * appears that if TXE is set, then TXB is not set.  However,
-	 * if carrier sense is lost during frame transmission, the TXE
-	 * bit is set, "and continues the buffer transmission normally."
-	 * I don't know if "normally" implies TXB is set when the buffer
-	 * descriptor is closed.....trial and error :-).
-	 */
-
-	/* Transmit OK, or non-fatal error.  Update the buffer descriptors.
-	*/
-	if (int_events & (SCCE_ENET_TXE | SCCE_ENET_TXB)) {
-	    spin_lock(&cep->lock);
-	    bdp = cep->dirty_tx;
-	    while ((bdp->cbd_sc&BD_ENET_TX_READY)==0) {
-		if ((bdp==cep->cur_tx) && (cep->tx_full == 0))
-		    break;
-
-		if (bdp->cbd_sc & BD_ENET_TX_HB)	/* No heartbeat */
-			cep->stats.tx_heartbeat_errors++;
-		if (bdp->cbd_sc & BD_ENET_TX_LC)	/* Late collision */
-			cep->stats.tx_window_errors++;
-		if (bdp->cbd_sc & BD_ENET_TX_RL)	/* Retrans limit */
-			cep->stats.tx_aborted_errors++;
-		if (bdp->cbd_sc & BD_ENET_TX_UN)	/* Underrun */
-			cep->stats.tx_fifo_errors++;
-		if (bdp->cbd_sc & BD_ENET_TX_CSL)	/* Carrier lost */
-			cep->stats.tx_carrier_errors++;
-
-
-		/* No heartbeat or Lost carrier are not really bad errors.
-		 * The others require a restart transmit command.
-		 */
-		if (bdp->cbd_sc &
-		    (BD_ENET_TX_LC | BD_ENET_TX_RL | BD_ENET_TX_UN)) {
-			must_restart = 1;
-			cep->stats.tx_errors++;
-		}
-
-		cep->stats.tx_packets++;
-
-		/* Deferred means some collisions occurred during transmit,
-		 * but we eventually sent the packet OK.
-		 */
-		if (bdp->cbd_sc & BD_ENET_TX_DEF)
-			cep->stats.collisions++;
-
-		/* Free the sk buffer associated with this last transmit.
-		*/
-		dev_kfree_skb_irq(cep->tx_skbuff[cep->skb_dirty]);
-		cep->skb_dirty = (cep->skb_dirty + 1) & TX_RING_MOD_MASK;
-
-		/* Update pointer to next buffer descriptor to be transmitted.
-		*/
-		if (bdp->cbd_sc & BD_ENET_TX_WRAP)
-			bdp = cep->tx_bd_base;
-		else
-			bdp++;
-
-		/* I don't know if we can be held off from processing these
-		 * interrupts for more than one frame time.  I really hope
-		 * not.  In such a case, we would now want to check the
-		 * currently available BD (cur_tx) and determine if any
-		 * buffers between the dirty_tx and cur_tx have also been
-		 * sent.  We would want to process anything in between that
-		 * does not have BD_ENET_TX_READY set.
-		 */
-
-		/* Since we have freed up a buffer, the ring is no longer
-		 * full.
-		 */
-		if (cep->tx_full) {
-			cep->tx_full = 0;
-			if (netif_queue_stopped(dev))
-				netif_wake_queue(dev);
-		}
-
-		cep->dirty_tx = (cbd_t *)bdp;
-	    }
-
-	    if (must_restart) {
-		volatile cpm8xx_t *cp;
-
-		/* Some transmit errors cause the transmitter to shut
-		 * down.  We now issue a restart transmit.  Since the
-		 * errors close the BD and update the pointers, the restart
-		 * _should_ pick up without having to reset any of our
-		 * pointers either.
-		 */
-		cp = cpmp;
-		cp->cp_cpcr =
-		    mk_cr_cmd(CPM_CR_ENET, CPM_CR_RESTART_TX) | CPM_CR_FLG;
-		while (cp->cp_cpcr & CPM_CR_FLG);
-	    }
-	    spin_unlock(&cep->lock);
-	}
-
-	/* Check for receive busy, i.e. packets coming but no place to
-	 * put them.  This "can't happen" because the receive interrupt
-	 * is tossing previous frames.
-	 */
-	if (int_events & SCCE_ENET_BSY) {
-		cep->stats.rx_dropped++;
-		printk("CPM ENET: BSY can't happen.\n");
-	}
-
-	return;
-}
-
-/* During a receive, the cur_rx points to the current incoming buffer.
- * When we update through the ring, if the next incoming buffer has
- * not been given to the system, we just set the empty indicator,
- * effectively tossing the packet.
- */
-static int
-scc_enet_rx(struct net_device *dev)
-{
-	struct	scc_enet_private *cep;
-	volatile cbd_t	*bdp;
-	struct	sk_buff *skb;
-	ushort	pkt_len;
-
-	cep = (struct scc_enet_private *)dev->priv;
-
-	/* First, grab all of the stats for the incoming packet.
-	 * These get messed up if we get called due to a busy condition.
-	 */
-	bdp = cep->cur_rx;
-
-for (;;) {
-	if (bdp->cbd_sc & BD_ENET_RX_EMPTY)
-		break;
-
-#ifndef final_version
-	/* Since we have allocated space to hold a complete frame, both
-	 * the first and last indicators should be set.
-	 */
-	if ((bdp->cbd_sc & (BD_ENET_RX_FIRST | BD_ENET_RX_LAST)) !=
-		(BD_ENET_RX_FIRST | BD_ENET_RX_LAST))
-			printk("CPM ENET: rcv is not first+last\n");
-#endif
-
-	/* Frame too long or too short.
-	*/
-	if (bdp->cbd_sc & (BD_ENET_RX_LG | BD_ENET_RX_SH))
-		cep->stats.rx_length_errors++;
-	if (bdp->cbd_sc & BD_ENET_RX_NO)	/* Frame alignment */
-		cep->stats.rx_frame_errors++;
-	if (bdp->cbd_sc & BD_ENET_RX_CR)	/* CRC Error */
-		cep->stats.rx_crc_errors++;
-	if (bdp->cbd_sc & BD_ENET_RX_OV)	/* FIFO overrun */
-		cep->stats.rx_crc_errors++;
-
-	/* Report late collisions as a frame error.
-	 * On this error, the BD is closed, but we don't know what we
-	 * have in the buffer.  So, just drop this frame on the floor.
-	 */
-	if (bdp->cbd_sc & BD_ENET_RX_CL) {
-		cep->stats.rx_frame_errors++;
-	}
-	else {
-
-		/* Process the incoming frame.
-		*/
-		cep->stats.rx_packets++;
-		pkt_len = bdp->cbd_datlen;
-		cep->stats.rx_bytes += pkt_len;
-
-		/* This does 16 byte alignment, much more than we need.
-		 * The packet length includes FCS, but we don't want to
-		 * include that when passing upstream as it messes up
-		 * bridging applications.
-		 */
-		skb = dev_alloc_skb(pkt_len-4);
-
-		if (skb == NULL) {
-			printk("%s: Memory squeeze, dropping packet.\n", dev->name);
-			cep->stats.rx_dropped++;
-		}
-		else {
-			skb_put(skb,pkt_len-4);	/* Make room */
-			skb_copy_to_linear_data(skb,
-				cep->rx_vaddr[bdp - cep->rx_bd_base],
-				pkt_len-4);
-			skb->protocol=eth_type_trans(skb,dev);
-			netif_rx(skb);
-		}
-	}
-
-	/* Clear the status flags for this buffer.
-	*/
-	bdp->cbd_sc &= ~BD_ENET_RX_STATS;
-
-	/* Mark the buffer empty.
-	*/
-	bdp->cbd_sc |= BD_ENET_RX_EMPTY;
-
-	/* Update BD pointer to next entry.
-	*/
-	if (bdp->cbd_sc & BD_ENET_RX_WRAP)
-		bdp = cep->rx_bd_base;
-	else
-		bdp++;
-
-   }
-	cep->cur_rx = (cbd_t *)bdp;
-
-	return 0;
-}
-
-static int
-scc_enet_close(struct net_device *dev)
-{
-	/* Don't know what to do yet.
-	*/
-	netif_stop_queue(dev);
-
-	return 0;
-}
-
-static struct net_device_stats *scc_enet_get_stats(struct net_device *dev)
-{
-	struct scc_enet_private *cep = (struct scc_enet_private *)dev->priv;
-
-	return &cep->stats;
-}
-
-/* Set or clear the multicast filter for this adaptor.
- * Skeleton taken from sunlance driver.
- * The CPM Ethernet implementation allows Multicast as well as individual
- * MAC address filtering.  Some of the drivers check to make sure it is
- * a group multicast address, and discard those that are not.  I guess I
- * will do the same for now, but just remove the test if you want
- * individual filtering as well (do the upper net layers want or support
- * this kind of feature?).
- */
-
-static void set_multicast_list(struct net_device *dev)
-{
-	struct	scc_enet_private *cep;
-	struct	dev_mc_list *dmi;
-	u_char	*mcptr, *tdptr;
-	volatile scc_enet_t *ep;
-	int	i, j;
-	cep = (struct scc_enet_private *)dev->priv;
-
-	/* Get pointer to SCC area in parameter RAM.
-	*/
-	ep = (scc_enet_t *)dev->base_addr;
-
-	if (dev->flags&IFF_PROMISC) {
-	
-		/* Log any net taps. */
-		printk("%s: Promiscuous mode enabled.\n", dev->name);
-		cep->sccp->scc_psmr |= SCC_PSMR_PRO;
-	} else {
-
-		cep->sccp->scc_psmr &= ~SCC_PSMR_PRO;
-
-		if (dev->flags & IFF_ALLMULTI) {
-			/* Catch all multicast addresses, so set the
-			 * filter to all 1's.
-			 */
-			ep->sen_gaddr1 = 0xffff;
-			ep->sen_gaddr2 = 0xffff;
-			ep->sen_gaddr3 = 0xffff;
-			ep->sen_gaddr4 = 0xffff;
-		}
-		else {
-			/* Clear filter and add the addresses in the list.
-			*/
-			ep->sen_gaddr1 = 0;
-			ep->sen_gaddr2 = 0;
-			ep->sen_gaddr3 = 0;
-			ep->sen_gaddr4 = 0;
-
-			dmi = dev->mc_list;
-
-			for (i=0; i<dev->mc_count; i++) {
-		
-				/* Only support group multicast for now.
-				*/
-				if (!(dmi->dmi_addr[0] & 1))
-					continue;
-
-				/* The address in dmi_addr is LSB first,
-				 * and taddr is MSB first.  We have to
-				 * copy bytes MSB first from dmi_addr.
-				 */
-				mcptr = (u_char *)dmi->dmi_addr + 5;
-				tdptr = (u_char *)&ep->sen_taddrh;
-				for (j=0; j<6; j++)
-					*tdptr++ = *mcptr--;
-
-				/* Ask CPM to run CRC and set bit in
-				 * filter mask.
-				 */
-				cpmp->cp_cpcr = mk_cr_cmd(CPM_CR_ENET, CPM_CR_SET_GADDR) | CPM_CR_FLG;
-				/* this delay is necessary here -- Cort */
-				udelay(10);
-				while (cpmp->cp_cpcr & CPM_CR_FLG);
-			}
-		}
-	}
-}
-
-/* Initialize the CPM Ethernet on SCC.  If EPPC-Bug loaded us, or performed
- * some other network I/O, a whole bunch of this has already been set up.
- * It is no big deal if we do it again, we just have to disable the
- * transmit and receive to make sure we don't catch the CPM with some
- * inconsistent control information.
- */
-static int __init scc_enet_init(void)
-{
-	struct net_device *dev;
-	struct scc_enet_private *cep;
-	int i, j, k, err;
-	uint dp_offset;
-	unsigned char	*eap, *ba;
-	dma_addr_t	mem_addr;
-	bd_t		*bd;
-	volatile	cbd_t		*bdp;
-	volatile	cpm8xx_t	*cp;
-	volatile	scc_t		*sccp;
-	volatile	scc_enet_t	*ep;
-	volatile	immap_t		*immap;
-
-	cp = cpmp;	/* Get pointer to Communication Processor */
-
-	immap = (immap_t *)(mfspr(SPRN_IMMR) & 0xFFFF0000);	/* and to internal registers */
-
-	bd = (bd_t *)__res;
-
-	dev = alloc_etherdev(sizeof(*cep));
-	if (!dev)
-		return -ENOMEM;
-
-	cep = dev->priv;
-	spin_lock_init(&cep->lock);
-
-	/* Get pointer to SCC area in parameter RAM.
-	*/
-	ep = (scc_enet_t *)(&cp->cp_dparam[PROFF_ENET]);
-
-	/* And another to the SCC register area.
-	*/
-	sccp = (volatile scc_t *)(&cp->cp_scc[SCC_ENET]);
-	cep->sccp = (scc_t *)sccp;		/* Keep the pointer handy */
-
-	/* Disable receive and transmit in case EPPC-Bug started it.
-	*/
-	sccp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-
-	/* Cookbook style from the MPC860 manual.....
-	 * Not all of this is necessary if EPPC-Bug has initialized
-	 * the network.
-	 * So far we are lucky, all board configurations use the same
-	 * pins, or at least the same I/O Port for these functions.....
-	 * It can't last though......
-	 */
-
-#if (defined(PA_ENET_RXD) && defined(PA_ENET_TXD))
-	/* Configure port A pins for Txd and Rxd.
-	*/
-	immap->im_ioport.iop_papar |=  (PA_ENET_RXD | PA_ENET_TXD);
-	immap->im_ioport.iop_padir &= ~(PA_ENET_RXD | PA_ENET_TXD);
-	immap->im_ioport.iop_paodr &=                ~PA_ENET_TXD;
-#elif (defined(PB_ENET_RXD) && defined(PB_ENET_TXD))
-	/* Configure port B pins for Txd and Rxd.
-	*/
-	immap->im_cpm.cp_pbpar |=  (PB_ENET_RXD | PB_ENET_TXD);
-	immap->im_cpm.cp_pbdir &= ~(PB_ENET_RXD | PB_ENET_TXD);
-	immap->im_cpm.cp_pbodr &=		 ~PB_ENET_TXD;
-#else
-#error Exactly ONE pair of PA_ENET_[RT]XD, PB_ENET_[RT]XD must be defined
-#endif
-
-#if defined(PC_ENET_LBK)
-	/* Configure port C pins to disable External Loopback
-	 */
-	immap->im_ioport.iop_pcpar &= ~PC_ENET_LBK;
-	immap->im_ioport.iop_pcdir |=  PC_ENET_LBK;
-	immap->im_ioport.iop_pcso  &= ~PC_ENET_LBK;
-	immap->im_ioport.iop_pcdat &= ~PC_ENET_LBK;	/* Disable Loopback */
-#endif	/* PC_ENET_LBK */
-
-#ifdef PE_ENET_TCLK
-	/* Configure port E for TCLK and RCLK.
-	*/
-	cp->cp_pepar |=  (PE_ENET_TCLK | PE_ENET_RCLK);
-	cp->cp_pedir &= ~(PE_ENET_TCLK | PE_ENET_RCLK);
-	cp->cp_peso  &= ~(PE_ENET_TCLK | PE_ENET_RCLK);
-#else
-	/* Configure port A for TCLK and RCLK.
-	*/
-	immap->im_ioport.iop_papar |=  (PA_ENET_TCLK | PA_ENET_RCLK);
-	immap->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);
-#endif
-
-	/* Configure port C pins to enable CLSN and RENA.
-	*/
-	immap->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
-	immap->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
-	immap->im_ioport.iop_pcso  |=  (PC_ENET_CLSN | PC_ENET_RENA);
-
-	/* Configure Serial Interface clock routing.
-	 * First, clear all SCC bits to zero, then set the ones we want.
-	 */
-	cp->cp_sicr &= ~SICR_ENET_MASK;
-	cp->cp_sicr |=  SICR_ENET_CLKRT;
-
-	/* Manual says set SDDR, but I can't find anything with that
-	 * name.  I think it is a misprint, and should be SDCR.  This
-	 * has already been set by the communication processor initialization.
-	 */
-
-	/* Allocate space for the buffer descriptors in the DP ram.
-	 * These are relative offsets in the DP ram address space.
-	 * Initialize base addresses for the buffer descriptors.
-	 */
-	dp_offset = cpm_dpalloc(sizeof(cbd_t) * RX_RING_SIZE, 8);
-	ep->sen_genscc.scc_rbase = dp_offset;
-	cep->rx_bd_base = cpm_dpram_addr(dp_offset);
-
-	dp_offset = cpm_dpalloc(sizeof(cbd_t) * TX_RING_SIZE, 8);
-	ep->sen_genscc.scc_tbase = dp_offset;
-	cep->tx_bd_base = cpm_dpram_addr(dp_offset);
-
-	cep->dirty_tx = cep->cur_tx = cep->tx_bd_base;
-	cep->cur_rx = cep->rx_bd_base;
-
-	/* Issue init Rx BD command for SCC.
-	 * Manual says to perform an Init Rx parameters here.  We have
-	 * to perform both Rx and Tx because the SCC may have been
-	 * already running.
-	 * In addition, we have to do it later because we don't yet have
-	 * all of the BD control/status set properly.
-	cp->cp_cpcr = mk_cr_cmd(CPM_CR_ENET, CPM_CR_INIT_RX) | CPM_CR_FLG;
-	while (cp->cp_cpcr & CPM_CR_FLG);
-	 */
-
-	/* Initialize function code registers for big-endian.
-	*/
-	ep->sen_genscc.scc_rfcr = SCC_EB;
-	ep->sen_genscc.scc_tfcr = SCC_EB;
-
-	/* Set maximum bytes per receive buffer.
-	 * This appears to be an Ethernet frame size, not the buffer
-	 * fragment size.  It must be a multiple of four.
-	 */
-	ep->sen_genscc.scc_mrblr = PKT_MAXBLR_SIZE;
-
-	/* Set CRC preset and mask.
-	*/
-	ep->sen_cpres = 0xffffffff;
-	ep->sen_cmask = 0xdebb20e3;
-
-	ep->sen_crcec = 0;	/* CRC Error counter */
-	ep->sen_alec = 0;	/* alignment error counter */
-	ep->sen_disfc = 0;	/* discard frame counter */
-
-	ep->sen_pads = 0x8888;	/* Tx short frame pad character */
-	ep->sen_retlim = 15;	/* Retry limit threshold */
-
-	ep->sen_maxflr = PKT_MAXBUF_SIZE;   /* maximum frame length register */
-	ep->sen_minflr = PKT_MINBUF_SIZE;  /* minimum frame length register */
-
-	ep->sen_maxd1 = PKT_MAXBLR_SIZE;	/* maximum DMA1 length */
-	ep->sen_maxd2 = PKT_MAXBLR_SIZE;	/* maximum DMA2 length */
-
-	/* Clear hash tables.
-	*/
-	ep->sen_gaddr1 = 0;
-	ep->sen_gaddr2 = 0;
-	ep->sen_gaddr3 = 0;
-	ep->sen_gaddr4 = 0;
-	ep->sen_iaddr1 = 0;
-	ep->sen_iaddr2 = 0;
-	ep->sen_iaddr3 = 0;
-	ep->sen_iaddr4 = 0;
-
-	/* Set Ethernet station address.
-	 */
-	eap = (unsigned char *)&(ep->sen_paddrh);
-	for (i=5; i>=0; i--)
-		*eap++ = dev->dev_addr[i] = bd->bi_enetaddr[i];
-
-	ep->sen_pper = 0;	/* 'cause the book says so */
-	ep->sen_taddrl = 0;	/* temp address (LSB) */
-	ep->sen_taddrm = 0;
-	ep->sen_taddrh = 0;	/* temp address (MSB) */
-
-	/* Now allocate the host memory pages and initialize the
-	 * buffer descriptors.
-	 */
-	bdp = cep->tx_bd_base;
-	for (i=0; i<TX_RING_SIZE; i++) {
-
-		/* Initialize the BD for every fragment in the page.
-		*/
-		bdp->cbd_sc = 0;
-		bdp->cbd_bufaddr = 0;
-		bdp++;
-	}
-
-	/* Set the last buffer to wrap.
-	*/
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
-	bdp = cep->rx_bd_base;
-	k = 0;
-	for (i=0; i<CPM_ENET_RX_PAGES; i++) {
-
-		/* Allocate a page.
-		*/
-		ba = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE,
-				&mem_addr, GFP_KERNEL);
-		/* BUG: no check for failure */
-
-		/* Initialize the BD for every fragment in the page.
-		*/
-		for (j=0; j<CPM_ENET_RX_FRPPG; j++) {
-			bdp->cbd_sc = BD_ENET_RX_EMPTY | BD_ENET_RX_INTR;
-			bdp->cbd_bufaddr = mem_addr;
-			cep->rx_vaddr[k++] = ba;
-			mem_addr += CPM_ENET_RX_FRSIZE;
-			ba += CPM_ENET_RX_FRSIZE;
-			bdp++;
-		}
-	}
-
-	/* Set the last buffer to wrap.
-	*/
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
-	/* Let's re-initialize the channel now.  We have to do it later
-	 * than the manual describes because we have just now finished
-	 * the BD initialization.
-	 */
-	cp->cp_cpcr = mk_cr_cmd(CPM_CR_ENET, CPM_CR_INIT_TRX) | CPM_CR_FLG;
-	while (cp->cp_cpcr & CPM_CR_FLG);
-
-	cep->skb_cur = cep->skb_dirty = 0;
-
-	sccp->scc_scce = 0xffff;	/* Clear any pending events */
-
-	/* Enable interrupts for transmit error, complete frame
-	 * received, and any transmit buffer we have also set the
-	 * interrupt flag.
-	 */
-	sccp->scc_sccm = (SCCE_ENET_TXE | SCCE_ENET_RXF | SCCE_ENET_TXB);
-
-	/* Install our interrupt handler.
-	*/
-	cpm_install_handler(CPMVEC_ENET, scc_enet_interrupt, dev);
-
-	/* Set GSMR_H to enable all normal operating modes.
-	 * Set GSMR_L to enable Ethernet to MC68160.
-	 */
-	sccp->scc_gsmrh = 0;
-	sccp->scc_gsmrl = (SCC_GSMRL_TCI | SCC_GSMRL_TPL_48 | SCC_GSMRL_TPP_10 | SCC_GSMRL_MODE_ENET);
-
-	/* Set sync/delimiters.
-	*/
-	sccp->scc_dsr = 0xd555;
-
-	/* Set processing mode.  Use Ethernet CRC, catch broadcast, and
-	 * start frame search 22 bit times after RENA.
-	 */
-	sccp->scc_psmr = (SCC_PSMR_ENCRC | SCC_PSMR_NIB22);
-
-	/* It is now OK to enable the Ethernet transmitter.
-	 * Unfortunately, there are board implementation differences here.
-	 */
-#if   (!defined (PB_ENET_TENA) &&  defined (PC_ENET_TENA) && !defined (PE_ENET_TENA))
-	immap->im_ioport.iop_pcpar |=  PC_ENET_TENA;
-	immap->im_ioport.iop_pcdir &= ~PC_ENET_TENA;
-#elif ( defined (PB_ENET_TENA) && !defined (PC_ENET_TENA) && !defined (PE_ENET_TENA))
-	cp->cp_pbpar |= PB_ENET_TENA;
-	cp->cp_pbdir |= PB_ENET_TENA;
-#elif ( !defined (PB_ENET_TENA) && !defined (PC_ENET_TENA) && defined (PE_ENET_TENA))
-	cp->cp_pepar |=  PE_ENET_TENA;
-	cp->cp_pedir &= ~PE_ENET_TENA;
-	cp->cp_peso  |=  PE_ENET_TENA;
-#else
-#error Configuration Error: define exactly ONE of PB_ENET_TENA, PC_ENET_TENA, PE_ENET_TENA
-#endif
-
-#if defined(CONFIG_RPXLITE) || defined(CONFIG_RPXCLASSIC)
-	/* And while we are here, set the configuration to enable ethernet.
-	*/
-	*((volatile uint *)RPX_CSR_ADDR) &= ~BCSR0_ETHLPBK;
-	*((volatile uint *)RPX_CSR_ADDR) |=
-			(BCSR0_ETHEN | BCSR0_COLTESTDIS | BCSR0_FULLDPLXDIS);
-#endif
-
-#ifdef CONFIG_BSEIP
-	/* BSE uses port B and C for PHY control.
-	*/
-	cp->cp_pbpar &= ~(PB_BSE_POWERUP | PB_BSE_FDXDIS);
-	cp->cp_pbdir |= (PB_BSE_POWERUP | PB_BSE_FDXDIS);
-	cp->cp_pbdat |= (PB_BSE_POWERUP | PB_BSE_FDXDIS);
-
-	immap->im_ioport.iop_pcpar &= ~PC_BSE_LOOPBACK;
-	immap->im_ioport.iop_pcdir |= PC_BSE_LOOPBACK;
-	immap->im_ioport.iop_pcso &= ~PC_BSE_LOOPBACK;
-	immap->im_ioport.iop_pcdat &= ~PC_BSE_LOOPBACK;
-#endif
-
-#ifdef CONFIG_FADS
-	cp->cp_pbpar |= PB_ENET_TENA;
-	cp->cp_pbdir |= PB_ENET_TENA;
-
-	/* Enable the EEST PHY.
-	*/
-	*((volatile uint *)BCSR1) &= ~BCSR1_ETHEN;
-#endif
-
-	dev->base_addr = (unsigned long)ep;
-#if 0
-	dev->name = "CPM_ENET";
-#endif
-
-	/* The CPM Ethernet specific entries in the device structure. */
-	dev->open = scc_enet_open;
-	dev->hard_start_xmit = scc_enet_start_xmit;
-	dev->tx_timeout = scc_enet_timeout;
-	dev->watchdog_timeo = TX_TIMEOUT;
-	dev->stop = scc_enet_close;
-	dev->get_stats = scc_enet_get_stats;
-	dev->set_multicast_list = set_multicast_list;
-
-	err = register_netdev(dev);
-	if (err) {
-		free_netdev(dev);
-		return err;
-	}
-
-	/* And last, enable the transmit and receive processing.
-	*/
-	sccp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-
-	printk("%s: CPM ENET Version 0.2 on SCC%d, ", dev->name, SCC_ENET+1);
-	for (i=0; i<5; i++)
-		printk("%02x:", dev->dev_addr[i]);
-	printk("%02x\n", dev->dev_addr[5]);
-
-	return 0;
-}
-
-module_init(scc_enet_init);
-
diff --git a/arch/ppc/8xx_io/fec.c b/arch/ppc/8xx_io/fec.c
deleted file mode 100644
index 2c604d4f6e8..00000000000
--- a/arch/ppc/8xx_io/fec.c
+++ /dev/null
@@ -1,1983 +0,0 @@
-/*
- * Fast Ethernet Controller (FEC) driver for Motorola MPC8xx.
- * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
- *
- * This version of the driver is specific to the FADS implementation,
- * since the board contains control registers external to the processor
- * for the control of the LevelOne LXT970 transceiver.  The MPC860T manual
- * describes connections using the internal parallel port I/O, which
- * is basically all of Port D.
- *
- * Includes support for the following PHYs: QS6612, LXT970, LXT971/2.
- *
- * Right now, I am very wasteful with the buffers.  I allocate memory
- * pages and then divide them into 2K frame buffers.  This way I know I
- * have buffers large enough to hold one frame within one buffer descriptor.
- * Once I get this working, I will use 64 or 128 byte CPM buffers, which
- * will be much more memory efficient and will easily handle lots of
- * small packets.
- *
- * Much better multiple PHY support by Magnus Damm.
- * Copyright (c) 2000 Ericsson Radio Systems AB.
- *
- * Make use of MII for PHY control configurable.
- * Some fixes.
- * Copyright (c) 2000-2002 Wolfgang Denk, DENX Software Engineering.
- *
- * Support for AMD AM79C874 added.
- * Thomas Lange, thomas@corelatus.com
- */
-
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/ptrace.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/bitops.h>
-#ifdef CONFIG_FEC_PACKETHOOK
-#include <linux/pkthook.h>
-#endif
-
-#include <asm/8xx_immap.h>
-#include <asm/pgtable.h>
-#include <asm/mpc8xx.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-#include <asm/cpm1.h>
-
-#ifdef	CONFIG_USE_MDIO
-/* Forward declarations of some structures to support different PHYs
-*/
-
-typedef struct {
-	uint mii_data;
-	void (*funct)(uint mii_reg, struct net_device *dev);
-} phy_cmd_t;
-
-typedef struct {
-	uint id;
-	char *name;
-
-	const phy_cmd_t *config;
-	const phy_cmd_t *startup;
-	const phy_cmd_t *ack_int;
-	const phy_cmd_t *shutdown;
-} phy_info_t;
-#endif	/* CONFIG_USE_MDIO */
-
-/* The number of Tx and Rx buffers.  These are allocated from the page
- * pool.  The code may assume these are power of two, so it is best
- * to keep them that size.
- * We don't need to allocate pages for the transmitter.  We just use
- * the skbuffer directly.
- */
-#ifdef CONFIG_ENET_BIG_BUFFERS
-#define FEC_ENET_RX_PAGES	16
-#define FEC_ENET_RX_FRSIZE	2048
-#define FEC_ENET_RX_FRPPG	(PAGE_SIZE / FEC_ENET_RX_FRSIZE)
-#define RX_RING_SIZE		(FEC_ENET_RX_FRPPG * FEC_ENET_RX_PAGES)
-#define TX_RING_SIZE		16	/* Must be power of two */
-#define TX_RING_MOD_MASK	15	/*   for this to work */
-#else
-#define FEC_ENET_RX_PAGES	4
-#define FEC_ENET_RX_FRSIZE	2048
-#define FEC_ENET_RX_FRPPG	(PAGE_SIZE / FEC_ENET_RX_FRSIZE)
-#define RX_RING_SIZE		(FEC_ENET_RX_FRPPG * FEC_ENET_RX_PAGES)
-#define TX_RING_SIZE		8	/* Must be power of two */
-#define TX_RING_MOD_MASK	7	/*   for this to work */
-#endif
-
-/* Interrupt events/masks.
-*/
-#define FEC_ENET_HBERR	((uint)0x80000000)	/* Heartbeat error */
-#define FEC_ENET_BABR	((uint)0x40000000)	/* Babbling receiver */
-#define FEC_ENET_BABT	((uint)0x20000000)	/* Babbling transmitter */
-#define FEC_ENET_GRA	((uint)0x10000000)	/* Graceful stop complete */
-#define FEC_ENET_TXF	((uint)0x08000000)	/* Full frame transmitted */
-#define FEC_ENET_TXB	((uint)0x04000000)	/* A buffer was transmitted */
-#define FEC_ENET_RXF	((uint)0x02000000)	/* Full frame received */
-#define FEC_ENET_RXB	((uint)0x01000000)	/* A buffer was received */
-#define FEC_ENET_MII	((uint)0x00800000)	/* MII interrupt */
-#define FEC_ENET_EBERR	((uint)0x00400000)	/* SDMA bus error */
-
-/*
-*/
-#define FEC_ECNTRL_PINMUX	0x00000004
-#define FEC_ECNTRL_ETHER_EN	0x00000002
-#define FEC_ECNTRL_RESET	0x00000001
-
-#define FEC_RCNTRL_BC_REJ	0x00000010
-#define FEC_RCNTRL_PROM		0x00000008
-#define FEC_RCNTRL_MII_MODE	0x00000004
-#define FEC_RCNTRL_DRT		0x00000002
-#define FEC_RCNTRL_LOOP		0x00000001
-
-#define FEC_TCNTRL_FDEN		0x00000004
-#define FEC_TCNTRL_HBC		0x00000002
-#define FEC_TCNTRL_GTS		0x00000001
-
-/* Delay to wait for FEC reset command to complete (in us)
-*/
-#define FEC_RESET_DELAY		50
-
-/* The FEC stores dest/src/type, data, and checksum for receive packets.
- */
-#define PKT_MAXBUF_SIZE		1518
-#define PKT_MINBUF_SIZE		64
-#define PKT_MAXBLR_SIZE		1520
-
-/* The FEC buffer descriptors track the ring buffers.  The rx_bd_base and
- * tx_bd_base always point to the base of the buffer descriptors.  The
- * cur_rx and cur_tx point to the currently available buffer.
- * The dirty_tx tracks the current buffer that is being sent by the
- * controller.  The cur_tx and dirty_tx are equal under both completely
- * empty and completely full conditions.  The empty/ready indicator in
- * the buffer descriptor determines the actual condition.
- */
-struct fec_enet_private {
-	/* The saved address of a sent-in-place packet/buffer, for skfree(). */
-	struct	sk_buff* tx_skbuff[TX_RING_SIZE];
-	ushort	skb_cur;
-	ushort	skb_dirty;
-
-	/* CPM dual port RAM relative addresses.
-	*/
-	cbd_t	*rx_bd_base;		/* Address of Rx and Tx buffers. */
-	cbd_t	*tx_bd_base;
-	cbd_t	*cur_rx, *cur_tx;		/* The next free ring entry */
-	cbd_t	*dirty_tx;	/* The ring entries to be free()ed. */
-
-	/* Virtual addresses for the receive buffers because we can't
-	 * do a __va() on them anymore.
-	 */
-	unsigned char *rx_vaddr[RX_RING_SIZE];
-
-	struct	net_device_stats stats;
-	uint	tx_full;
-	spinlock_t lock;
-
-#ifdef	CONFIG_USE_MDIO
-	uint	phy_id;
-	uint	phy_id_done;
-	uint	phy_status;
-	uint	phy_speed;
-	phy_info_t	*phy;
-	struct work_struct phy_task;
-	struct net_device *dev;
-
-	uint	sequence_done;
-
-	uint	phy_addr;
-#endif	/* CONFIG_USE_MDIO */
-
-	int	link;
-	int	old_link;
-	int	full_duplex;
-
-#ifdef CONFIG_FEC_PACKETHOOK
-	unsigned long	ph_lock;
-	fec_ph_func	*ph_rxhandler;
-	fec_ph_func	*ph_txhandler;
-	__u16		ph_proto;
-	volatile __u32	*ph_regaddr;
-	void 		*ph_priv;
-#endif
-};
-
-static int fec_enet_open(struct net_device *dev);
-static int fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev);
-#ifdef	CONFIG_USE_MDIO
-static void fec_enet_mii(struct net_device *dev);
-#endif	/* CONFIG_USE_MDIO */
-#ifdef CONFIG_FEC_PACKETHOOK
-static void  fec_enet_tx(struct net_device *dev, __u32 regval);
-static void  fec_enet_rx(struct net_device *dev, __u32 regval);
-#else
-static void  fec_enet_tx(struct net_device *dev);
-static void  fec_enet_rx(struct net_device *dev);
-#endif
-static int fec_enet_close(struct net_device *dev);
-static struct net_device_stats *fec_enet_get_stats(struct net_device *dev);
-static void set_multicast_list(struct net_device *dev);
-static void fec_restart(struct net_device *dev, int duplex);
-static void fec_stop(struct net_device *dev);
-static	ushort	my_enet_addr[3];
-
-#ifdef	CONFIG_USE_MDIO
-/* MII processing.  We keep this as simple as possible.  Requests are
- * placed on the list (if there is room).  When the request is finished
- * by the MII, an optional function may be called.
- */
-typedef struct mii_list {
-	uint	mii_regval;
-	void	(*mii_func)(uint val, struct net_device *dev);
-	struct	mii_list *mii_next;
-} mii_list_t;
-
-#define		NMII	20
-mii_list_t	mii_cmds[NMII];
-mii_list_t	*mii_free;
-mii_list_t	*mii_head;
-mii_list_t	*mii_tail;
-
-static int	mii_queue(struct net_device *dev, int request,
-				void (*func)(uint, struct net_device *));
-
-/* Make MII read/write commands for the FEC.
-*/
-#define mk_mii_read(REG)	(0x60020000 | ((REG & 0x1f) << 18))
-#define mk_mii_write(REG, VAL)	(0x50020000 | ((REG & 0x1f) << 18) | \
-						(VAL & 0xffff))
-#define mk_mii_end	0
-#endif	/* CONFIG_USE_MDIO */
-
-/* Transmitter timeout.
-*/
-#define TX_TIMEOUT (2*HZ)
-
-#ifdef	CONFIG_USE_MDIO
-/* Register definitions for the PHY.
-*/
-
-#define MII_REG_CR          0  /* Control Register                         */
-#define MII_REG_SR          1  /* Status Register                          */
-#define MII_REG_PHYIR1      2  /* PHY Identification Register 1            */
-#define MII_REG_PHYIR2      3  /* PHY Identification Register 2            */
-#define MII_REG_ANAR        4  /* A-N Advertisement Register               */
-#define MII_REG_ANLPAR      5  /* A-N Link Partner Ability Register        */
-#define MII_REG_ANER        6  /* A-N Expansion Register                   */
-#define MII_REG_ANNPTR      7  /* A-N Next Page Transmit Register          */
-#define MII_REG_ANLPRNPR    8  /* A-N Link Partner Received Next Page Reg. */
-
-/* values for phy_status */
-
-#define PHY_CONF_ANE	0x0001  /* 1 auto-negotiation enabled */
-#define PHY_CONF_LOOP	0x0002  /* 1 loopback mode enabled */
-#define PHY_CONF_SPMASK	0x00f0  /* mask for speed */
-#define PHY_CONF_10HDX	0x0010  /* 10 Mbit half duplex supported */
-#define PHY_CONF_10FDX	0x0020  /* 10 Mbit full duplex supported */
-#define PHY_CONF_100HDX	0x0040  /* 100 Mbit half duplex supported */
-#define PHY_CONF_100FDX	0x0080  /* 100 Mbit full duplex supported */
-
-#define PHY_STAT_LINK	0x0100  /* 1 up - 0 down */
-#define PHY_STAT_FAULT	0x0200  /* 1 remote fault */
-#define PHY_STAT_ANC	0x0400  /* 1 auto-negotiation complete	*/
-#define PHY_STAT_SPMASK	0xf000  /* mask for speed */
-#define PHY_STAT_10HDX	0x1000  /* 10 Mbit half duplex selected	*/
-#define PHY_STAT_10FDX	0x2000  /* 10 Mbit full duplex selected	*/
-#define PHY_STAT_100HDX	0x4000  /* 100 Mbit half duplex selected */
-#define PHY_STAT_100FDX	0x8000  /* 100 Mbit full duplex selected */
-#endif	/* CONFIG_USE_MDIO */
-
-#ifdef CONFIG_FEC_PACKETHOOK
-int
-fec_register_ph(struct net_device *dev, fec_ph_func *rxfun, fec_ph_func *txfun,
-		__u16 proto, volatile __u32 *regaddr, void *priv)
-{
-	struct fec_enet_private *fep;
-	int retval = 0;
-
-	fep = dev->priv;
-
-	if (test_and_set_bit(0, (void*)&fep->ph_lock) != 0) {
-		/* Someone is messing with the packet hook */
-		return -EAGAIN;
-	}
-	if (fep->ph_rxhandler != NULL || fep->ph_txhandler != NULL) {
-		retval = -EBUSY;
-		goto out;
-	}
-	fep->ph_rxhandler = rxfun;
-	fep->ph_txhandler = txfun;
-	fep->ph_proto = proto;
-	fep->ph_regaddr = regaddr;
-	fep->ph_priv = priv;
-
-	out:
-	fep->ph_lock = 0;
-
-	return retval;
-}
-
-
-int
-fec_unregister_ph(struct net_device *dev)
-{
-	struct fec_enet_private *fep;
-	int retval = 0;
-
-	fep = dev->priv;
-
-	if (test_and_set_bit(0, (void*)&fep->ph_lock) != 0) {
-		/* Someone is messing with the packet hook */
-		return -EAGAIN;
-	}
-
-	fep->ph_rxhandler = fep->ph_txhandler = NULL;
-	fep->ph_proto = 0;
-	fep->ph_regaddr = NULL;
-	fep->ph_priv = NULL;
-
-	fep->ph_lock = 0;
-
-	return retval;
-}
-
-EXPORT_SYMBOL(fec_register_ph);
-EXPORT_SYMBOL(fec_unregister_ph);
-
-#endif /* CONFIG_FEC_PACKETHOOK */
-
-static int
-fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
-{
-	struct fec_enet_private *fep;
-	volatile fec_t	*fecp;
-	volatile cbd_t	*bdp;
-
-	fep = dev->priv;
-	fecp = (volatile fec_t*)dev->base_addr;
-
-	if (!fep->link) {
-		/* Link is down or autonegotiation is in progress. */
-		return 1;
-	}
-
-	/* Fill in a Tx ring entry */
-	bdp = fep->cur_tx;
-
-#ifndef final_version
-	if (bdp->cbd_sc & BD_ENET_TX_READY) {
-		/* Ooops.  All transmit buffers are full.  Bail out.
-		 * This should not happen, since dev->tbusy should be set.
-		 */
-		printk("%s: tx queue full!.\n", dev->name);
-		return 1;
-	}
-#endif
-
-	/* Clear all of the status flags.
-	 */
-	bdp->cbd_sc &= ~BD_ENET_TX_STATS;
-
-	/* Set buffer length and buffer pointer.
-	*/
-	bdp->cbd_bufaddr = __pa(skb->data);
-	bdp->cbd_datlen = skb->len;
-
-	/* Save skb pointer.
-	*/
-	fep->tx_skbuff[fep->skb_cur] = skb;
-
-	fep->stats.tx_bytes += skb->len;
-	fep->skb_cur = (fep->skb_cur+1) & TX_RING_MOD_MASK;
-
-	/* Push the data cache so the CPM does not get stale memory
-	 * data.
-	 */
-	flush_dcache_range((unsigned long)skb->data,
-			   (unsigned long)skb->data + skb->len);
-
-	/* disable interrupts while triggering transmit */
-	spin_lock_irq(&fep->lock);
-
-	/* Send it on its way.  Tell FEC its ready, interrupt when done,
-	 * its the last BD of the frame, and to put the CRC on the end.
-	 */
-
-	bdp->cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_INTR
-			| BD_ENET_TX_LAST | BD_ENET_TX_TC);
-
-	dev->trans_start = jiffies;
-
-	/* Trigger transmission start */
-	fecp->fec_x_des_active = 0x01000000;
-
-	/* If this was the last BD in the ring, start at the beginning again.
-	*/
-	if (bdp->cbd_sc & BD_ENET_TX_WRAP) {
-		bdp = fep->tx_bd_base;
-	} else {
-		bdp++;
-	}
-
-	if (bdp->cbd_sc & BD_ENET_TX_READY) {
-		netif_stop_queue(dev);
-		fep->tx_full = 1;
-	}
-
-	fep->cur_tx = (cbd_t *)bdp;
-
-	spin_unlock_irq(&fep->lock);
-
-	return 0;
-}
-
-static void
-fec_timeout(struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-
-	printk("%s: transmit timed out.\n", dev->name);
-	fep->stats.tx_errors++;
-#ifndef final_version
-	{
-	int	i;
-	cbd_t	*bdp;
-
-	printk("Ring data dump: cur_tx %lx%s, dirty_tx %lx cur_rx: %lx\n",
-	       (unsigned long)fep->cur_tx, fep->tx_full ? " (full)" : "",
-	       (unsigned long)fep->dirty_tx,
-	       (unsigned long)fep->cur_rx);
-
-	bdp = fep->tx_bd_base;
-	printk(" tx: %u buffers\n",  TX_RING_SIZE);
-	for (i = 0 ; i < TX_RING_SIZE; i++) {
-		printk("  %08x: %04x %04x %08x\n",
-		       (uint) bdp,
-		       bdp->cbd_sc,
-		       bdp->cbd_datlen,
-		       bdp->cbd_bufaddr);
-		bdp++;
-	}
-
-	bdp = fep->rx_bd_base;
-	printk(" rx: %lu buffers\n",  RX_RING_SIZE);
-	for (i = 0 ; i < RX_RING_SIZE; i++) {
-		printk("  %08x: %04x %04x %08x\n",
-		       (uint) bdp,
-		       bdp->cbd_sc,
-		       bdp->cbd_datlen,
-		       bdp->cbd_bufaddr);
-		bdp++;
-	}
-	}
-#endif
-	if (!fep->tx_full)
-		netif_wake_queue(dev);
-}
-
-/* The interrupt handler.
- * This is called from the MPC core interrupt.
- */
-static	irqreturn_t
-fec_enet_interrupt(int irq, void *dev_id)
-{
-	struct	net_device *dev = dev_id;
-	volatile fec_t	*fecp;
-	uint	int_events;
-#ifdef CONFIG_FEC_PACKETHOOK
-	struct	fec_enet_private *fep = dev->priv;
-	__u32 regval;
-
-	if (fep->ph_regaddr) regval = *fep->ph_regaddr;
-#endif
-	fecp = (volatile fec_t*)dev->base_addr;
-
-	/* Get the interrupt events that caused us to be here.
-	*/
-	while ((int_events = fecp->fec_ievent) != 0) {
-		fecp->fec_ievent = int_events;
-		if ((int_events & (FEC_ENET_HBERR | FEC_ENET_BABR |
-				   FEC_ENET_BABT | FEC_ENET_EBERR)) != 0) {
-			printk("FEC ERROR %x\n", int_events);
-		}
-
-		/* Handle receive event in its own function.
-		 */
-		if (int_events & FEC_ENET_RXF) {
-#ifdef CONFIG_FEC_PACKETHOOK
-			fec_enet_rx(dev, regval);
-#else
-			fec_enet_rx(dev);
-#endif
-		}
-
-		/* Transmit OK, or non-fatal error. Update the buffer
-		   descriptors. FEC handles all errors, we just discover
-		   them as part of the transmit process.
-		*/
-		if (int_events & FEC_ENET_TXF) {
-#ifdef CONFIG_FEC_PACKETHOOK
-			fec_enet_tx(dev, regval);
-#else
-			fec_enet_tx(dev);
-#endif
-		}
-
-		if (int_events & FEC_ENET_MII) {
-#ifdef	CONFIG_USE_MDIO
-			fec_enet_mii(dev);
-#else
-printk("%s[%d] %s: unexpected FEC_ENET_MII event\n", __FILE__, __LINE__, __func__);
-#endif	/* CONFIG_USE_MDIO */
-		}
-
-	}
-	return IRQ_RETVAL(IRQ_HANDLED);
-}
-
-
-static void
-#ifdef CONFIG_FEC_PACKETHOOK
-fec_enet_tx(struct net_device *dev, __u32 regval)
-#else
-fec_enet_tx(struct net_device *dev)
-#endif
-{
-	struct	fec_enet_private *fep;
-	volatile cbd_t	*bdp;
-	struct	sk_buff	*skb;
-
-	fep = dev->priv;
-	/* lock while transmitting */
-	spin_lock(&fep->lock);
-	bdp = fep->dirty_tx;
-
-	while ((bdp->cbd_sc&BD_ENET_TX_READY) == 0) {
-		if (bdp == fep->cur_tx && fep->tx_full == 0) break;
-
-		skb = fep->tx_skbuff[fep->skb_dirty];
-		/* Check for errors. */
-		if (bdp->cbd_sc & (BD_ENET_TX_HB | BD_ENET_TX_LC |
-				   BD_ENET_TX_RL | BD_ENET_TX_UN |
-				   BD_ENET_TX_CSL)) {
-			fep->stats.tx_errors++;
-			if (bdp->cbd_sc & BD_ENET_TX_HB)  /* No heartbeat */
-				fep->stats.tx_heartbeat_errors++;
-			if (bdp->cbd_sc & BD_ENET_TX_LC)  /* Late collision */
-				fep->stats.tx_window_errors++;
-			if (bdp->cbd_sc & BD_ENET_TX_RL)  /* Retrans limit */
-				fep->stats.tx_aborted_errors++;
-			if (bdp->cbd_sc & BD_ENET_TX_UN)  /* Underrun */
-				fep->stats.tx_fifo_errors++;
-			if (bdp->cbd_sc & BD_ENET_TX_CSL) /* Carrier lost */
-				fep->stats.tx_carrier_errors++;
-		} else {
-#ifdef CONFIG_FEC_PACKETHOOK
-			/* Packet hook ... */
-			if (fep->ph_txhandler &&
-			    ((struct ethhdr *)skb->data)->h_proto
-			    == fep->ph_proto) {
-				fep->ph_txhandler((__u8*)skb->data, skb->len,
-						  regval, fep->ph_priv);
-			}
-#endif
-			fep->stats.tx_packets++;
-		}
-
-#ifndef final_version
-		if (bdp->cbd_sc & BD_ENET_TX_READY)
-			printk("HEY! Enet xmit interrupt and TX_READY.\n");
-#endif
-		/* Deferred means some collisions occurred during transmit,
-		 * but we eventually sent the packet OK.
-		 */
-		if (bdp->cbd_sc & BD_ENET_TX_DEF)
-			fep->stats.collisions++;
-
-		/* Free the sk buffer associated with this last transmit.
-		 */
-#if 0
-printk("TXI: %x %x %x\n", bdp, skb, fep->skb_dirty);
-#endif
-		dev_kfree_skb_irq (skb/*, FREE_WRITE*/);
-		fep->tx_skbuff[fep->skb_dirty] = NULL;
-		fep->skb_dirty = (fep->skb_dirty + 1) & TX_RING_MOD_MASK;
-
-		/* Update pointer to next buffer descriptor to be transmitted.
-		 */
-		if (bdp->cbd_sc & BD_ENET_TX_WRAP)
-			bdp = fep->tx_bd_base;
-		else
-			bdp++;
-
-		/* Since we have freed up a buffer, the ring is no longer
-		 * full.
-		 */
-		if (fep->tx_full) {
-			fep->tx_full = 0;
-			if (netif_queue_stopped(dev))
-				netif_wake_queue(dev);
-		}
-#ifdef CONFIG_FEC_PACKETHOOK
-		/* Re-read register. Not exactly guaranteed to be correct,
-		   but... */
-		if (fep->ph_regaddr) regval = *fep->ph_regaddr;
-#endif
-	}
-	fep->dirty_tx = (cbd_t *)bdp;
-	spin_unlock(&fep->lock);
-}
-
-
-/* During a receive, the cur_rx points to the current incoming buffer.
- * When we update through the ring, if the next incoming buffer has
- * not been given to the system, we just set the empty indicator,
- * effectively tossing the packet.
- */
-static void
-#ifdef CONFIG_FEC_PACKETHOOK
-fec_enet_rx(struct net_device *dev, __u32 regval)
-#else
-fec_enet_rx(struct net_device *dev)
-#endif
-{
-	struct	fec_enet_private *fep;
-	volatile fec_t	*fecp;
-	volatile cbd_t *bdp;
-	struct	sk_buff	*skb;
-	ushort	pkt_len;
-	__u8 *data;
-
-	fep = dev->priv;
-	fecp = (volatile fec_t*)dev->base_addr;
-
-	/* First, grab all of the stats for the incoming packet.
-	 * These get messed up if we get called due to a busy condition.
-	 */
-	bdp = fep->cur_rx;
-
-while (!(bdp->cbd_sc & BD_ENET_RX_EMPTY)) {
-
-#ifndef final_version
-	/* Since we have allocated space to hold a complete frame,
-	 * the last indicator should be set.
-	 */
-	if ((bdp->cbd_sc & BD_ENET_RX_LAST) == 0)
-		printk("FEC ENET: rcv is not +last\n");
-#endif
-
-	/* Check for errors. */
-	if (bdp->cbd_sc & (BD_ENET_RX_LG | BD_ENET_RX_SH | BD_ENET_RX_NO |
-			   BD_ENET_RX_CR | BD_ENET_RX_OV)) {
-		fep->stats.rx_errors++;
-		if (bdp->cbd_sc & (BD_ENET_RX_LG | BD_ENET_RX_SH)) {
-		/* Frame too long or too short. */
-			fep->stats.rx_length_errors++;
-		}
-		if (bdp->cbd_sc & BD_ENET_RX_NO)	/* Frame alignment */
-			fep->stats.rx_frame_errors++;
-		if (bdp->cbd_sc & BD_ENET_RX_CR)	/* CRC Error */
-			fep->stats.rx_crc_errors++;
-		if (bdp->cbd_sc & BD_ENET_RX_OV)	/* FIFO overrun */
-			fep->stats.rx_crc_errors++;
-	}
-
-	/* Report late collisions as a frame error.
-	 * On this error, the BD is closed, but we don't know what we
-	 * have in the buffer.  So, just drop this frame on the floor.
-	 */
-	if (bdp->cbd_sc & BD_ENET_RX_CL) {
-		fep->stats.rx_errors++;
-		fep->stats.rx_frame_errors++;
-		goto rx_processing_done;
-	}
-
-	/* Process the incoming frame.
-	 */
-	fep->stats.rx_packets++;
-	pkt_len = bdp->cbd_datlen;
-	fep->stats.rx_bytes += pkt_len;
-	data = fep->rx_vaddr[bdp - fep->rx_bd_base];
-
-#ifdef CONFIG_FEC_PACKETHOOK
-	/* Packet hook ... */
-	if (fep->ph_rxhandler) {
-		if (((struct ethhdr *)data)->h_proto == fep->ph_proto) {
-			switch (fep->ph_rxhandler(data, pkt_len, regval,
-						  fep->ph_priv)) {
-			case 1:
-				goto rx_processing_done;
-				break;
-			case 0:
-				break;
-			default:
-				fep->stats.rx_errors++;
-				goto rx_processing_done;
-			}
-		}
-	}
-
-	/* If it wasn't filtered - copy it to an sk buffer. */
-#endif
-
-	/* This does 16 byte alignment, exactly what we need.
-	 * The packet length includes FCS, but we don't want to
-	 * include that when passing upstream as it messes up
-	 * bridging applications.
-	 */
-	skb = dev_alloc_skb(pkt_len-4);
-
-	if (skb == NULL) {
-		printk("%s: Memory squeeze, dropping packet.\n", dev->name);
-		fep->stats.rx_dropped++;
-	} else {
-		skb_put(skb,pkt_len-4);	/* Make room */
-		skb_copy_to_linear_data(skb, data, pkt_len-4);
-		skb->protocol=eth_type_trans(skb,dev);
-		netif_rx(skb);
-	}
-  rx_processing_done:
-
-	/* Clear the status flags for this buffer.
-	*/
-	bdp->cbd_sc &= ~BD_ENET_RX_STATS;
-
-	/* Mark the buffer empty.
-	*/
-	bdp->cbd_sc |= BD_ENET_RX_EMPTY;
-
-	/* Update BD pointer to next entry.
-	*/
-	if (bdp->cbd_sc & BD_ENET_RX_WRAP)
-		bdp = fep->rx_bd_base;
-	else
-		bdp++;
-
-#if 1
-	/* Doing this here will keep the FEC running while we process
-	 * incoming frames.  On a heavily loaded network, we should be
-	 * able to keep up at the expense of system resources.
-	 */
-	fecp->fec_r_des_active = 0x01000000;
-#endif
-#ifdef CONFIG_FEC_PACKETHOOK
-	/* Re-read register. Not exactly guaranteed to be correct,
-	   but... */
-	if (fep->ph_regaddr) regval = *fep->ph_regaddr;
-#endif
-   } /* while (!(bdp->cbd_sc & BD_ENET_RX_EMPTY)) */
-	fep->cur_rx = (cbd_t *)bdp;
-
-#if 0
-	/* Doing this here will allow us to process all frames in the
-	 * ring before the FEC is allowed to put more there.  On a heavily
-	 * loaded network, some frames may be lost.  Unfortunately, this
-	 * increases the interrupt overhead since we can potentially work
-	 * our way back to the interrupt return only to come right back
-	 * here.
-	 */
-	fecp->fec_r_des_active = 0x01000000;
-#endif
-}
-
-
-#ifdef	CONFIG_USE_MDIO
-static void
-fec_enet_mii(struct net_device *dev)
-{
-	struct	fec_enet_private *fep;
-	volatile fec_t	*ep;
-	mii_list_t	*mip;
-	uint		mii_reg;
-
-	fep = (struct fec_enet_private *)dev->priv;
-	ep = &(((immap_t *)IMAP_ADDR)->im_cpm.cp_fec);
-	mii_reg = ep->fec_mii_data;
-
-	if ((mip = mii_head) == NULL) {
-		printk("MII and no head!\n");
-		return;
-	}
-
-	if (mip->mii_func != NULL)
-		(*(mip->mii_func))(mii_reg, dev);
-
-	mii_head = mip->mii_next;
-	mip->mii_next = mii_free;
-	mii_free = mip;
-
-	if ((mip = mii_head) != NULL) {
-		ep->fec_mii_data = mip->mii_regval;
-
-	}
-}
-
-static int
-mii_queue(struct net_device *dev, int regval, void (*func)(uint, struct net_device *))
-{
-	struct fec_enet_private *fep;
-	unsigned long	flags;
-	mii_list_t	*mip;
-	int		retval;
-
-	/* Add PHY address to register command.
-	*/
-	fep = dev->priv;
-	regval |= fep->phy_addr << 23;
-
-	retval = 0;
-
-	/* lock while modifying mii_list */
-	spin_lock_irqsave(&fep->lock, flags);
-
-	if ((mip = mii_free) != NULL) {
-		mii_free = mip->mii_next;
-		mip->mii_regval = regval;
-		mip->mii_func = func;
-		mip->mii_next = NULL;
-		if (mii_head) {
-			mii_tail->mii_next = mip;
-			mii_tail = mip;
-		} else {
-			mii_head = mii_tail = mip;
-			(&(((immap_t *)IMAP_ADDR)->im_cpm.cp_fec))->fec_mii_data = regval;
-		}
-	} else {
-		retval = 1;
-	}
-
-	spin_unlock_irqrestore(&fep->lock, flags);
-
-	return(retval);
-}
-
-static void mii_do_cmd(struct net_device *dev, const phy_cmd_t *c)
-{
-	int k;
-
-	if(!c)
-		return;
-
-	for(k = 0; (c+k)->mii_data != mk_mii_end; k++)
-		mii_queue(dev, (c+k)->mii_data, (c+k)->funct);
-}
-
-static void mii_parse_sr(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-	volatile uint *s = &(fep->phy_status);
-
-	*s &= ~(PHY_STAT_LINK | PHY_STAT_FAULT | PHY_STAT_ANC);
-
-	if (mii_reg & 0x0004)
-		*s |= PHY_STAT_LINK;
-	if (mii_reg & 0x0010)
-		*s |= PHY_STAT_FAULT;
-	if (mii_reg & 0x0020)
-		*s |= PHY_STAT_ANC;
-
-	fep->link = (*s & PHY_STAT_LINK) ? 1 : 0;
-}
-
-static void mii_parse_cr(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-	volatile uint *s = &(fep->phy_status);
-
-	*s &= ~(PHY_CONF_ANE | PHY_CONF_LOOP);
-
-	if (mii_reg & 0x1000)
-		*s |= PHY_CONF_ANE;
-	if (mii_reg & 0x4000)
-		*s |= PHY_CONF_LOOP;
-}
-
-static void mii_parse_anar(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-	volatile uint *s = &(fep->phy_status);
-
-	*s &= ~(PHY_CONF_SPMASK);
-
-	if (mii_reg & 0x0020)
-		*s |= PHY_CONF_10HDX;
-	if (mii_reg & 0x0040)
-		*s |= PHY_CONF_10FDX;
-	if (mii_reg & 0x0080)
-		*s |= PHY_CONF_100HDX;
-	if (mii_reg & 0x00100)
-		*s |= PHY_CONF_100FDX;
-}
-#if 0
-static void mii_disp_reg(uint mii_reg, struct net_device *dev)
-{
-	printk("reg %u = 0x%04x\n", (mii_reg >> 18) & 0x1f, mii_reg & 0xffff);
-}
-#endif
-
-/* ------------------------------------------------------------------------- */
-/* The Level one LXT970 is used by many boards				     */
-
-#ifdef CONFIG_FEC_LXT970
-
-#define MII_LXT970_MIRROR    16  /* Mirror register           */
-#define MII_LXT970_IER       17  /* Interrupt Enable Register */
-#define MII_LXT970_ISR       18  /* Interrupt Status Register */
-#define MII_LXT970_CONFIG    19  /* Configuration Register    */
-#define MII_LXT970_CSR       20  /* Chip Status Register      */
-
-static void mii_parse_lxt970_csr(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-	volatile uint *s = &(fep->phy_status);
-
-	*s &= ~(PHY_STAT_SPMASK);
-
-	if (mii_reg & 0x0800) {
-		if (mii_reg & 0x1000)
-			*s |= PHY_STAT_100FDX;
-		else
-			*s |= PHY_STAT_100HDX;
-	}
-	else {
-		if (mii_reg & 0x1000)
-			*s |= PHY_STAT_10FDX;
-		else
-			*s |= PHY_STAT_10HDX;
-	}
-}
-
-static phy_info_t phy_info_lxt970 = {
-	0x07810000,
-	"LXT970",
-
-	(const phy_cmd_t []) {  /* config */
-#if 0
-//		{ mk_mii_write(MII_REG_ANAR, 0x0021), NULL },
-
-		/* Set default operation of 100-TX....for some reason
-		 * some of these bits are set on power up, which is wrong.
-		 */
-		{ mk_mii_write(MII_LXT970_CONFIG, 0), NULL },
-#endif
-		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
-		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) {  /* startup - enable interrupts */
-		{ mk_mii_write(MII_LXT970_IER, 0x0002), NULL },
-		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) { /* ack_int */
-		/* read SR and ISR to acknowledge */
-
-		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
-		{ mk_mii_read(MII_LXT970_ISR), NULL },
-
-		/* find out the current status */
-
-		{ mk_mii_read(MII_LXT970_CSR), mii_parse_lxt970_csr },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) {  /* shutdown - disable interrupts */
-		{ mk_mii_write(MII_LXT970_IER, 0x0000), NULL },
-		{ mk_mii_end, }
-	},
-};
-
-#endif /* CONFIG_FEC_LXT970 */
-
-/* ------------------------------------------------------------------------- */
-/* The Level one LXT971 is used on some of my custom boards                  */
-
-#ifdef CONFIG_FEC_LXT971
-
-/* register definitions for the 971 */
-
-#define MII_LXT971_PCR       16  /* Port Control Register     */
-#define MII_LXT971_SR2       17  /* Status Register 2         */
-#define MII_LXT971_IER       18  /* Interrupt Enable Register */
-#define MII_LXT971_ISR       19  /* Interrupt Status Register */
-#define MII_LXT971_LCR       20  /* LED Control Register      */
-#define MII_LXT971_TCR       30  /* Transmit Control Register */
-
-/*
- * I had some nice ideas of running the MDIO faster...
- * The 971 should support 8MHz and I tried it, but things acted really
- * weird, so 2.5 MHz ought to be enough for anyone...
- */
-
-static void mii_parse_lxt971_sr2(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-	volatile uint *s = &(fep->phy_status);
-
-	*s &= ~(PHY_STAT_SPMASK);
-
-	if (mii_reg & 0x4000) {
-		if (mii_reg & 0x0200)
-			*s |= PHY_STAT_100FDX;
-		else
-			*s |= PHY_STAT_100HDX;
-	}
-	else {
-		if (mii_reg & 0x0200)
-			*s |= PHY_STAT_10FDX;
-		else
-			*s |= PHY_STAT_10HDX;
-	}
-	if (mii_reg & 0x0008)
-		*s |= PHY_STAT_FAULT;
-}
-
-static phy_info_t phy_info_lxt971 = {
-	0x0001378e,
-	"LXT971",
-
-	(const phy_cmd_t []) {  /* config */
-//		{ mk_mii_write(MII_REG_ANAR, 0x021), NULL }, /* 10  Mbps, HD */
-		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
-		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) {  /* startup - enable interrupts */
-		{ mk_mii_write(MII_LXT971_IER, 0x00f2), NULL },
-		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
-
-		/* Somehow does the 971 tell me that the link is down
-		 * the first read after power-up.
-		 * read here to get a valid value in ack_int */
-
-		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) { /* ack_int */
-		/* find out the current status */
-
-		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
-		{ mk_mii_read(MII_LXT971_SR2), mii_parse_lxt971_sr2 },
-
-		/* we only need to read ISR to acknowledge */
-
-		{ mk_mii_read(MII_LXT971_ISR), NULL },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) {  /* shutdown - disable interrupts */
-		{ mk_mii_write(MII_LXT971_IER, 0x0000), NULL },
-		{ mk_mii_end, }
-	},
-};
-
-#endif /* CONFIG_FEC_LXT970 */
-
-
-/* ------------------------------------------------------------------------- */
-/* The Quality Semiconductor QS6612 is used on the RPX CLLF                  */
-
-#ifdef CONFIG_FEC_QS6612
-
-/* register definitions */
-
-#define MII_QS6612_MCR       17  /* Mode Control Register      */
-#define MII_QS6612_FTR       27  /* Factory Test Register      */
-#define MII_QS6612_MCO       28  /* Misc. Control Register     */
-#define MII_QS6612_ISR       29  /* Interrupt Source Register  */
-#define MII_QS6612_IMR       30  /* Interrupt Mask Register    */
-#define MII_QS6612_PCR       31  /* 100BaseTx PHY Control Reg. */
-
-static void mii_parse_qs6612_pcr(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-	volatile uint *s = &(fep->phy_status);
-
-	*s &= ~(PHY_STAT_SPMASK);
-
-	switch((mii_reg >> 2) & 7) {
-	case 1: *s |= PHY_STAT_10HDX; break;
-	case 2: *s |= PHY_STAT_100HDX; break;
-	case 5: *s |= PHY_STAT_10FDX; break;
-	case 6: *s |= PHY_STAT_100FDX; break;
-	}
-}
-
-static phy_info_t phy_info_qs6612 = {
-	0x00181440,
-	"QS6612",
-
-	(const phy_cmd_t []) {  /* config */
-//	{ mk_mii_write(MII_REG_ANAR, 0x061), NULL }, /* 10  Mbps */
-
-		/* The PHY powers up isolated on the RPX,
-		 * so send a command to allow operation.
-		 */
-
-		{ mk_mii_write(MII_QS6612_PCR, 0x0dc0), NULL },
-
-		/* parse cr and anar to get some info */
-
-		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
-		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) {  /* startup - enable interrupts */
-		{ mk_mii_write(MII_QS6612_IMR, 0x003a), NULL },
-		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) { /* ack_int */
-
-		/* we need to read ISR, SR and ANER to acknowledge */
-
-		{ mk_mii_read(MII_QS6612_ISR), NULL },
-		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
-		{ mk_mii_read(MII_REG_ANER), NULL },
-
-		/* read pcr to get info */
-
-		{ mk_mii_read(MII_QS6612_PCR), mii_parse_qs6612_pcr },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) {  /* shutdown - disable interrupts */
-		{ mk_mii_write(MII_QS6612_IMR, 0x0000), NULL },
-		{ mk_mii_end, }
-	},
-};
-
-#endif /* CONFIG_FEC_QS6612 */
-
-/* ------------------------------------------------------------------------- */
-/* The Advanced Micro Devices AM79C874 is used on the ICU862		     */
-
-#ifdef CONFIG_FEC_AM79C874
-
-/* register definitions for the 79C874 */
-
-#define MII_AM79C874_MFR	16  /* Miscellaneous Features Register      */
-#define MII_AM79C874_ICSR	17  /* Interrupt Control/Status Register    */
-#define MII_AM79C874_DR		18  /* Diagnostic Register		    */
-#define MII_AM79C874_PMLR	19  /* Power Management & Loopback Register */
-#define MII_AM79C874_MCR	21  /* Mode Control Register		    */
-#define MII_AM79C874_DC		23  /* Disconnect Counter		    */
-#define MII_AM79C874_REC	24  /* Receiver Error Counter		    */
-
-static void mii_parse_amd79c874_dr(uint mii_reg, struct net_device *dev, uint data)
-{
-	volatile struct fec_enet_private *fep = dev->priv;
-	uint s = fep->phy_status;
-
-	s &= ~(PHY_STAT_SPMASK);
-
-	/* Register 18: Bit 10 is data rate, 11 is Duplex */
-	switch ((mii_reg >> 10) & 3) {
-	case 0:	s |= PHY_STAT_10HDX;	break;
-	case 1:	s |= PHY_STAT_100HDX;	break;
-	case 2:	s |= PHY_STAT_10FDX;	break;
-	case 3:	s |= PHY_STAT_100FDX;	break;
-	}
-
-	fep->phy_status = s;
-}
-
-static phy_info_t phy_info_amd79c874 = {
-	0x00022561,
-	"AM79C874",
-
-	(const phy_cmd_t []) {  /* config */
-//		{ mk_mii_write(MII_REG_ANAR, 0x021), NULL }, /* 10  Mbps, HD */
-		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
-		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) {  /* startup - enable interrupts */
-		{ mk_mii_write(MII_AM79C874_ICSR, 0xff00), NULL },
-		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) { /* ack_int */
-		/* find out the current status */
-
-		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
-		{ mk_mii_read(MII_AM79C874_DR), mii_parse_amd79c874_dr },
-
-		/* we only need to read ICSR to acknowledge */
-
-		{ mk_mii_read(MII_AM79C874_ICSR), NULL },
-		{ mk_mii_end, }
-	},
-	(const phy_cmd_t []) {  /* shutdown - disable interrupts */
-		{ mk_mii_write(MII_AM79C874_ICSR, 0x0000), NULL },
-		{ mk_mii_end, }
-	},
-};
-
-#endif /* CONFIG_FEC_AM79C874 */
-
-static phy_info_t *phy_info[] = {
-
-#ifdef CONFIG_FEC_LXT970
-	&phy_info_lxt970,
-#endif /* CONFIG_FEC_LXT970 */
-
-#ifdef CONFIG_FEC_LXT971
-	&phy_info_lxt971,
-#endif /* CONFIG_FEC_LXT971 */
-
-#ifdef CONFIG_FEC_QS6612
-	&phy_info_qs6612,
-#endif /* CONFIG_FEC_QS6612 */
-
-#ifdef CONFIG_FEC_AM79C874
-	&phy_info_amd79c874,
-#endif /* CONFIG_FEC_AM79C874 */
-
-	NULL
-};
-
-static void mii_display_status(struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-	volatile uint *s = &(fep->phy_status);
-
-	if (!fep->link && !fep->old_link) {
-		/* Link is still down - don't print anything */
-		return;
-	}
-
-	printk("%s: status: ", dev->name);
-
-	if (!fep->link) {
-		printk("link down");
-	} else {
-		printk("link up");
-
-		switch(*s & PHY_STAT_SPMASK) {
-		case PHY_STAT_100FDX: printk(", 100 Mbps Full Duplex"); break;
-		case PHY_STAT_100HDX: printk(", 100 Mbps Half Duplex"); break;
-		case PHY_STAT_10FDX: printk(", 10 Mbps Full Duplex"); break;
-		case PHY_STAT_10HDX: printk(", 10 Mbps Half Duplex"); break;
-		default:
-			printk(", Unknown speed/duplex");
-		}
-
-		if (*s & PHY_STAT_ANC)
-			printk(", auto-negotiation complete");
-	}
-
-	if (*s & PHY_STAT_FAULT)
-		printk(", remote fault");
-
-	printk(".\n");
-}
-
-static void mii_display_config(struct work_struct *work)
-{
-	struct fec_enet_private *fep =
-		container_of(work, struct fec_enet_private, phy_task);
-	struct net_device *dev = fep->dev;
-	volatile uint *s = &(fep->phy_status);
-
-	printk("%s: config: auto-negotiation ", dev->name);
-
-	if (*s & PHY_CONF_ANE)
-		printk("on");
-	else
-		printk("off");
-
-	if (*s & PHY_CONF_100FDX)
-		printk(", 100FDX");
-	if (*s & PHY_CONF_100HDX)
-		printk(", 100HDX");
-	if (*s & PHY_CONF_10FDX)
-		printk(", 10FDX");
-	if (*s & PHY_CONF_10HDX)
-		printk(", 10HDX");
-	if (!(*s & PHY_CONF_SPMASK))
-		printk(", No speed/duplex selected?");
-
-	if (*s & PHY_CONF_LOOP)
-		printk(", loopback enabled");
-
-	printk(".\n");
-
-	fep->sequence_done = 1;
-}
-
-static void mii_relink(struct work_struct *work)
-{
-	struct fec_enet_private *fep =
-		container_of(work, struct fec_enet_private, phy_task);
-	struct net_device *dev = fep->dev;
-	int duplex;
-
-	fep->link = (fep->phy_status & PHY_STAT_LINK) ? 1 : 0;
-	mii_display_status(dev);
-	fep->old_link = fep->link;
-
-	if (fep->link) {
-		duplex = 0;
-		if (fep->phy_status
-		    & (PHY_STAT_100FDX | PHY_STAT_10FDX))
-			duplex = 1;
-		fec_restart(dev, duplex);
-	}
-	else
-		fec_stop(dev);
-
-#if 0
-	enable_irq(fep->mii_irq);
-#endif
-
-}
-
-static void mii_queue_relink(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-
-	fep->dev = dev;
-	INIT_WORK(&fep->phy_task, mii_relink);
-	schedule_work(&fep->phy_task);
-}
-
-static void mii_queue_config(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-
-	fep->dev = dev;
-	INIT_WORK(&fep->phy_task, mii_display_config);
-	schedule_work(&fep->phy_task);
-}
-
-
-
-phy_cmd_t phy_cmd_relink[] = { { mk_mii_read(MII_REG_CR), mii_queue_relink },
-			       { mk_mii_end, } };
-phy_cmd_t phy_cmd_config[] = { { mk_mii_read(MII_REG_CR), mii_queue_config },
-			       { mk_mii_end, } };
-
-
-
-/* Read remainder of PHY ID.
-*/
-static void
-mii_discover_phy3(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep;
-	int	i;
-
-	fep = dev->priv;
-	fep->phy_id |= (mii_reg & 0xffff);
-
-	for(i = 0; phy_info[i]; i++)
-		if(phy_info[i]->id == (fep->phy_id >> 4))
-			break;
-
-	if(!phy_info[i])
-		panic("%s: PHY id 0x%08x is not supported!\n",
-		      dev->name, fep->phy_id);
-
-	fep->phy = phy_info[i];
-	fep->phy_id_done = 1;
-
-	printk("%s: Phy @ 0x%x, type %s (0x%08x)\n",
-		dev->name, fep->phy_addr, fep->phy->name, fep->phy_id);
-}
-
-/* Scan all of the MII PHY addresses looking for someone to respond
- * with a valid ID.  This usually happens quickly.
- */
-static void
-mii_discover_phy(uint mii_reg, struct net_device *dev)
-{
-	struct fec_enet_private *fep;
-	uint	phytype;
-
-	fep = dev->priv;
-
-	if ((phytype = (mii_reg & 0xffff)) != 0xffff) {
-
-		/* Got first part of ID, now get remainder.
-		*/
-		fep->phy_id = phytype << 16;
-		mii_queue(dev, mk_mii_read(MII_REG_PHYIR2), mii_discover_phy3);
-	} else {
-		fep->phy_addr++;
-		if (fep->phy_addr < 32) {
-			mii_queue(dev, mk_mii_read(MII_REG_PHYIR1),
-							mii_discover_phy);
-		} else {
-			printk("fec: No PHY device found.\n");
-		}
-	}
-}
-#endif	/* CONFIG_USE_MDIO */
-
-/* This interrupt occurs when the PHY detects a link change.
-*/
-static
-#ifdef CONFIG_RPXCLASSIC
-void mii_link_interrupt(void *dev_id)
-#else
-irqreturn_t mii_link_interrupt(int irq, void * dev_id)
-#endif
-{
-#ifdef	CONFIG_USE_MDIO
-	struct	net_device *dev = dev_id;
-	struct fec_enet_private *fep = dev->priv;
-	volatile immap_t *immap = (immap_t *)IMAP_ADDR;
-	volatile fec_t *fecp = &(immap->im_cpm.cp_fec);
-	unsigned int ecntrl = fecp->fec_ecntrl;
-
-	/* We need the FEC enabled to access the MII
-	*/
-	if ((ecntrl & FEC_ECNTRL_ETHER_EN) == 0) {
-		fecp->fec_ecntrl |= FEC_ECNTRL_ETHER_EN;
-	}
-#endif	/* CONFIG_USE_MDIO */
-
-#if 0
-	disable_irq(fep->mii_irq);  /* disable now, enable later */
-#endif
-
-
-#ifdef	CONFIG_USE_MDIO
-	mii_do_cmd(dev, fep->phy->ack_int);
-	mii_do_cmd(dev, phy_cmd_relink);  /* restart and display status */
-
-	if ((ecntrl & FEC_ECNTRL_ETHER_EN) == 0) {
-		fecp->fec_ecntrl = ecntrl;	/* restore old settings */
-	}
-#else
-printk("%s[%d] %s: unexpected Link interrupt\n", __FILE__, __LINE__, __func__);
-#endif	/* CONFIG_USE_MDIO */
-
-#ifndef CONFIG_RPXCLASSIC
-	return IRQ_RETVAL(IRQ_HANDLED);
-#endif	/* CONFIG_RPXCLASSIC */
-}
-
-static int
-fec_enet_open(struct net_device *dev)
-{
-	struct fec_enet_private *fep = dev->priv;
-
-	/* I should reset the ring buffers here, but I don't yet know
-	 * a simple way to do that.
-	 */
-
-#ifdef	CONFIG_USE_MDIO
-	fep->sequence_done = 0;
-	fep->link = 0;
-
-	if (fep->phy) {
-		mii_do_cmd(dev, fep->phy->ack_int);
-		mii_do_cmd(dev, fep->phy->config);
-		mii_do_cmd(dev, phy_cmd_config);  /* display configuration */
-		while(!fep->sequence_done)
-			schedule();
-
-		mii_do_cmd(dev, fep->phy->startup);
-		netif_start_queue(dev);
-		return 0;		/* Success */
-	}
-	return -ENODEV;		/* No PHY we understand */
-#else
-	fep->link = 1;
-	netif_start_queue(dev);
-	return 0;	/* Success */
-#endif	/* CONFIG_USE_MDIO */
-
-}
-
-static int
-fec_enet_close(struct net_device *dev)
-{
-	/* Don't know what to do yet.
-	*/
-	netif_stop_queue(dev);
-	fec_stop(dev);
-
-	return 0;
-}
-
-static struct net_device_stats *fec_enet_get_stats(struct net_device *dev)
-{
-	struct fec_enet_private *fep = (struct fec_enet_private *)dev->priv;
-
-	return &fep->stats;
-}
-
-/* Set or clear the multicast filter for this adaptor.
- * Skeleton taken from sunlance driver.
- * The CPM Ethernet implementation allows Multicast as well as individual
- * MAC address filtering.  Some of the drivers check to make sure it is
- * a group multicast address, and discard those that are not.  I guess I
- * will do the same for now, but just remove the test if you want
- * individual filtering as well (do the upper net layers want or support
- * this kind of feature?).
- */
-
-static void set_multicast_list(struct net_device *dev)
-{
-	struct	fec_enet_private *fep;
-	volatile fec_t *ep;
-
-	fep = (struct fec_enet_private *)dev->priv;
-	ep = &(((immap_t *)IMAP_ADDR)->im_cpm.cp_fec);
-
-	if (dev->flags&IFF_PROMISC) {
-
-		/* Log any net taps. */
-		printk("%s: Promiscuous mode enabled.\n", dev->name);
-		ep->fec_r_cntrl |= FEC_RCNTRL_PROM;
-	} else {
-
-		ep->fec_r_cntrl &= ~FEC_RCNTRL_PROM;
-
-		if (dev->flags & IFF_ALLMULTI) {
-			/* Catch all multicast addresses, so set the
-			 * filter to all 1's.
-			 */
-			ep->fec_hash_table_high = 0xffffffff;
-			ep->fec_hash_table_low = 0xffffffff;
-		}
-#if 0
-		else {
-			/* Clear filter and add the addresses in the list.
-			*/
-			ep->sen_gaddr1 = 0;
-			ep->sen_gaddr2 = 0;
-			ep->sen_gaddr3 = 0;
-			ep->sen_gaddr4 = 0;
-
-			dmi = dev->mc_list;
-
-			for (i=0; i<dev->mc_count; i++) {
-
-				/* Only support group multicast for now.
-				*/
-				if (!(dmi->dmi_addr[0] & 1))
-					continue;
-
-				/* The address in dmi_addr is LSB first,
-				 * and taddr is MSB first.  We have to
-				 * copy bytes MSB first from dmi_addr.
-				 */
-				mcptr = (u_char *)dmi->dmi_addr + 5;
-				tdptr = (u_char *)&ep->sen_taddrh;
-				for (j=0; j<6; j++)
-					*tdptr++ = *mcptr--;
-
-				/* Ask CPM to run CRC and set bit in
-				 * filter mask.
-				 */
-				cpmp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SCC1, CPM_CR_SET_GADDR) | CPM_CR_FLG;
-				/* this delay is necessary here -- Cort */
-				udelay(10);
-				while (cpmp->cp_cpcr & CPM_CR_FLG);
-			}
-		}
-#endif
-	}
-}
-
-/* Initialize the FEC Ethernet on 860T.
- */
-static int __init fec_enet_init(void)
-{
-	struct net_device *dev;
-	struct fec_enet_private *fep;
-	int i, j, k, err;
-	unsigned char	*eap, *iap, *ba;
-	dma_addr_t	mem_addr;
-	volatile	cbd_t	*bdp;
-	cbd_t		*cbd_base;
-	volatile	immap_t	*immap;
-	volatile	fec_t	*fecp;
-	bd_t		*bd;
-#ifdef CONFIG_SCC_ENET
-	unsigned char	tmpaddr[6];
-#endif
-
-	immap = (immap_t *)IMAP_ADDR;	/* pointer to internal registers */
-
-	bd = (bd_t *)__res;
-
-	dev = alloc_etherdev(sizeof(*fep));
-	if (!dev)
-		return -ENOMEM;
-
-	fep = dev->priv;
-
-	fecp = &(immap->im_cpm.cp_fec);
-
-	/* Whack a reset.  We should wait for this.
-	*/
-	fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_RESET;
-	for (i = 0;
-	     (fecp->fec_ecntrl & FEC_ECNTRL_RESET) && (i < FEC_RESET_DELAY);
-	     ++i) {
-		udelay(1);
-	}
-	if (i == FEC_RESET_DELAY) {
-		printk ("FEC Reset timeout!\n");
-	}
-
-	/* Set the Ethernet address.  If using multiple Enets on the 8xx,
-	 * this needs some work to get unique addresses.
-	 */
-	eap = (unsigned char *)my_enet_addr;
-	iap = bd->bi_enetaddr;
-
-#ifdef CONFIG_SCC_ENET
-	/*
-         * If a board has Ethernet configured both on a SCC and the
-         * FEC, it needs (at least) 2 MAC addresses (we know that Sun
-         * disagrees, but anyway). For the FEC port, we create
-         * another address by setting one of the address bits above
-         * something that would have (up to now) been allocated.
-	 */
-	for (i=0; i<6; i++)
-		tmpaddr[i] = *iap++;
-	tmpaddr[3] |= 0x80;
-	iap = tmpaddr;
-#endif
-
-	for (i=0; i<6; i++) {
-		dev->dev_addr[i] = *eap++ = *iap++;
-	}
-
-	/* Allocate memory for buffer descriptors.
-	*/
-	if (((RX_RING_SIZE + TX_RING_SIZE) * sizeof(cbd_t)) > PAGE_SIZE) {
-		printk("FEC init error.  Need more space.\n");
-		printk("FEC initialization failed.\n");
-		return 1;
-	}
-	cbd_base = (cbd_t *)dma_alloc_coherent(dev->class_dev.dev, PAGE_SIZE,
-					       &mem_addr, GFP_KERNEL);
-
-	/* Set receive and transmit descriptor base.
-	*/
-	fep->rx_bd_base = cbd_base;
-	fep->tx_bd_base = cbd_base + RX_RING_SIZE;
-
-	fep->skb_cur = fep->skb_dirty = 0;
-
-	/* Initialize the receive buffer descriptors.
-	*/
-	bdp = fep->rx_bd_base;
-	k = 0;
-	for (i=0; i<FEC_ENET_RX_PAGES; i++) {
-
-		/* Allocate a page.
-		*/
-		ba = (unsigned char *)dma_alloc_coherent(dev->class_dev.dev,
-							 PAGE_SIZE,
-							 &mem_addr,
-							 GFP_KERNEL);
-		/* BUG: no check for failure */
-
-		/* Initialize the BD for every fragment in the page.
-		*/
-		for (j=0; j<FEC_ENET_RX_FRPPG; j++) {
-			bdp->cbd_sc = BD_ENET_RX_EMPTY;
-			bdp->cbd_bufaddr = mem_addr;
-			fep->rx_vaddr[k++] = ba;
-			mem_addr += FEC_ENET_RX_FRSIZE;
-			ba += FEC_ENET_RX_FRSIZE;
-			bdp++;
-		}
-	}
-
-	/* Set the last buffer to wrap.
-	*/
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
-#ifdef CONFIG_FEC_PACKETHOOK
-	fep->ph_lock = 0;
-	fep->ph_rxhandler = fep->ph_txhandler = NULL;
-	fep->ph_proto = 0;
-	fep->ph_regaddr = NULL;
-	fep->ph_priv = NULL;
-#endif
-
-	/* Install our interrupt handler.
-	*/
-	if (request_irq(FEC_INTERRUPT, fec_enet_interrupt, 0, "fec", dev) != 0)
-		panic("Could not allocate FEC IRQ!");
-
-#ifdef CONFIG_RPXCLASSIC
-	/* Make Port C, bit 15 an input that causes interrupts.
-	*/
-	immap->im_ioport.iop_pcpar &= ~0x0001;
-	immap->im_ioport.iop_pcdir &= ~0x0001;
-	immap->im_ioport.iop_pcso  &= ~0x0001;
-	immap->im_ioport.iop_pcint |=  0x0001;
-	cpm_install_handler(CPMVEC_PIO_PC15, mii_link_interrupt, dev);
-
-	/* Make LEDS reflect Link status.
-	*/
-	*((uint *) RPX_CSR_ADDR) &= ~BCSR2_FETHLEDMODE;
-#endif
-
-#ifdef PHY_INTERRUPT
-	((immap_t *)IMAP_ADDR)->im_siu_conf.sc_siel |=
-		(0x80000000 >> PHY_INTERRUPT);
-
-	if (request_irq(PHY_INTERRUPT, mii_link_interrupt, 0, "mii", dev) != 0)
-		panic("Could not allocate MII IRQ!");
-#endif
-
-	dev->base_addr = (unsigned long)fecp;
-
-	/* The FEC Ethernet specific entries in the device structure. */
-	dev->open = fec_enet_open;
-	dev->hard_start_xmit = fec_enet_start_xmit;
-	dev->tx_timeout = fec_timeout;
-	dev->watchdog_timeo = TX_TIMEOUT;
-	dev->stop = fec_enet_close;
-	dev->get_stats = fec_enet_get_stats;
-	dev->set_multicast_list = set_multicast_list;
-
-#ifdef	CONFIG_USE_MDIO
-	for (i=0; i<NMII-1; i++)
-		mii_cmds[i].mii_next = &mii_cmds[i+1];
-	mii_free = mii_cmds;
-#endif	/* CONFIG_USE_MDIO */
-
-	/* Configure all of port D for MII.
-	*/
-	immap->im_ioport.iop_pdpar = 0x1fff;
-
-	/* Bits moved from Rev. D onward.
-	*/
-	if ((mfspr(SPRN_IMMR) & 0xffff) < 0x0501)
-		immap->im_ioport.iop_pddir = 0x1c58;	/* Pre rev. D */
-	else
-		immap->im_ioport.iop_pddir = 0x1fff;	/* Rev. D and later */
-
-#ifdef	CONFIG_USE_MDIO
-	/* Set MII speed to 2.5 MHz
-	*/
-	fecp->fec_mii_speed = fep->phy_speed =
-		(( (bd->bi_intfreq + 500000) / 2500000 / 2 ) & 0x3F ) << 1;
-#else
-	fecp->fec_mii_speed = 0;	/* turn off MDIO */
-#endif	/* CONFIG_USE_MDIO */
-
-	err = register_netdev(dev);
-	if (err) {
-		free_netdev(dev);
-		return err;
-	}
-
-	printk ("%s: FEC ENET Version 0.2, FEC irq %d"
-#ifdef PHY_INTERRUPT
-		", MII irq %d"
-#endif
-		", addr ",
-		dev->name, FEC_INTERRUPT
-#ifdef PHY_INTERRUPT
-		, PHY_INTERRUPT
-#endif
-	);
-	for (i=0; i<6; i++)
-		printk("%02x%c", dev->dev_addr[i], (i==5) ? '\n' : ':');
-
-#ifdef	CONFIG_USE_MDIO	/* start in full duplex mode, and negotiate speed */
-	fec_restart (dev, 1);
-#else			/* always use half duplex mode only */
-	fec_restart (dev, 0);
-#endif
-
-#ifdef	CONFIG_USE_MDIO
-	/* Queue up command to detect the PHY and initialize the
-	 * remainder of the interface.
-	 */
-	fep->phy_id_done = 0;
-	fep->phy_addr = 0;
-	mii_queue(dev, mk_mii_read(MII_REG_PHYIR1), mii_discover_phy);
-#endif	/* CONFIG_USE_MDIO */
-
-	return 0;
-}
-module_init(fec_enet_init);
-
-/* This function is called to start or restart the FEC during a link
- * change.  This only happens when switching between half and full
- * duplex.
- */
-static void
-fec_restart(struct net_device *dev, int duplex)
-{
-	struct fec_enet_private *fep;
-	int i;
-	volatile	cbd_t	*bdp;
-	volatile	immap_t	*immap;
-	volatile	fec_t	*fecp;
-
-	immap = (immap_t *)IMAP_ADDR;	/* pointer to internal registers */
-
-	fecp = &(immap->im_cpm.cp_fec);
-
-	fep = dev->priv;
-
-	/* Whack a reset.  We should wait for this.
-	*/
-	fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_RESET;
-	for (i = 0;
-	     (fecp->fec_ecntrl & FEC_ECNTRL_RESET) && (i < FEC_RESET_DELAY);
-	     ++i) {
-		udelay(1);
-	}
-	if (i == FEC_RESET_DELAY) {
-		printk ("FEC Reset timeout!\n");
-	}
-
-	/* Set station address.
-	*/
-	fecp->fec_addr_low  = (my_enet_addr[0] << 16) | my_enet_addr[1];
-	fecp->fec_addr_high =  my_enet_addr[2];
-
-	/* Reset all multicast.
-	*/
-	fecp->fec_hash_table_high = 0;
-	fecp->fec_hash_table_low  = 0;
-
-	/* Set maximum receive buffer size.
-	*/
-	fecp->fec_r_buff_size = PKT_MAXBLR_SIZE;
-	fecp->fec_r_hash = PKT_MAXBUF_SIZE;
-
-	/* Set receive and transmit descriptor base.
-	*/
-	fecp->fec_r_des_start = iopa((uint)(fep->rx_bd_base));
-	fecp->fec_x_des_start = iopa((uint)(fep->tx_bd_base));
-
-	fep->dirty_tx = fep->cur_tx = fep->tx_bd_base;
-	fep->cur_rx = fep->rx_bd_base;
-
-	/* Reset SKB transmit buffers.
-	*/
-	fep->skb_cur = fep->skb_dirty = 0;
-	for (i=0; i<=TX_RING_MOD_MASK; i++) {
-		if (fep->tx_skbuff[i] != NULL) {
-			dev_kfree_skb(fep->tx_skbuff[i]);
-			fep->tx_skbuff[i] = NULL;
-		}
-	}
-
-	/* Initialize the receive buffer descriptors.
-	*/
-	bdp = fep->rx_bd_base;
-	for (i=0; i<RX_RING_SIZE; i++) {
-
-		/* Initialize the BD for every fragment in the page.
-		*/
-		bdp->cbd_sc = BD_ENET_RX_EMPTY;
-		bdp++;
-	}
-
-	/* Set the last buffer to wrap.
-	*/
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
-	/* ...and the same for transmit.
-	*/
-	bdp = fep->tx_bd_base;
-	for (i=0; i<TX_RING_SIZE; i++) {
-
-		/* Initialize the BD for every fragment in the page.
-		*/
-		bdp->cbd_sc = 0;
-		bdp->cbd_bufaddr = 0;
-		bdp++;
-	}
-
-	/* Set the last buffer to wrap.
-	*/
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
-	/* Enable MII mode.
-	*/
-	if (duplex) {
-		fecp->fec_r_cntrl = FEC_RCNTRL_MII_MODE;	/* MII enable */
-		fecp->fec_x_cntrl = FEC_TCNTRL_FDEN;		/* FD enable */
-	}
-	else {
-		fecp->fec_r_cntrl = FEC_RCNTRL_MII_MODE | FEC_RCNTRL_DRT;
-		fecp->fec_x_cntrl = 0;
-	}
-	fep->full_duplex = duplex;
-
-	/* Enable big endian and don't care about SDMA FC.
-	*/
-	fecp->fec_fun_code = 0x78000000;
-
-#ifdef	CONFIG_USE_MDIO
-	/* Set MII speed.
-	*/
-	fecp->fec_mii_speed = fep->phy_speed;
-#endif	/* CONFIG_USE_MDIO */
-
-	/* Clear any outstanding interrupt.
-	*/
-	fecp->fec_ievent = 0xffc0;
-
-	fecp->fec_ivec = (FEC_INTERRUPT/2) << 29;
-
-	/* Enable interrupts we wish to service.
-	*/
-	fecp->fec_imask = ( FEC_ENET_TXF | FEC_ENET_TXB |
-			    FEC_ENET_RXF | FEC_ENET_RXB | FEC_ENET_MII );
-
-	/* And last, enable the transmit and receive processing.
-	*/
-	fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN;
-	fecp->fec_r_des_active = 0x01000000;
-}
-
-static void
-fec_stop(struct net_device *dev)
-{
-	volatile	immap_t	*immap;
-	volatile	fec_t	*fecp;
-	struct fec_enet_private *fep;
-	int i;
-
-	immap = (immap_t *)IMAP_ADDR;	/* pointer to internal registers */
-
-	fecp = &(immap->im_cpm.cp_fec);
-
-	if ((fecp->fec_ecntrl & FEC_ECNTRL_ETHER_EN) == 0)
-		return;	/* already down */
-
-	fep = dev->priv;
-
-
-	fecp->fec_x_cntrl = 0x01;	/* Graceful transmit stop */
-
-	for (i = 0;
-	     ((fecp->fec_ievent & 0x10000000) == 0) && (i < FEC_RESET_DELAY);
-	     ++i) {
-		udelay(1);
-	}
-	if (i == FEC_RESET_DELAY) {
-		printk ("FEC timeout on graceful transmit stop\n");
-	}
-
-	/* Clear outstanding MII command interrupts.
-	*/
-	fecp->fec_ievent = FEC_ENET_MII;
-
-	/* Enable MII command finished interrupt
-	*/
-	fecp->fec_ivec = (FEC_INTERRUPT/2) << 29;
-	fecp->fec_imask = FEC_ENET_MII;
-
-#ifdef	CONFIG_USE_MDIO
-	/* Set MII speed.
-	*/
-	fecp->fec_mii_speed = fep->phy_speed;
-#endif	/* CONFIG_USE_MDIO */
-
-	/* Disable FEC
-	*/
-	fecp->fec_ecntrl &= ~(FEC_ECNTRL_ETHER_EN);
-}
diff --git a/arch/ppc/8xx_io/micropatch.c b/arch/ppc/8xx_io/micropatch.c
deleted file mode 100644
index 9a5d95da7c2..00000000000
--- a/arch/ppc/8xx_io/micropatch.c
+++ /dev/null
@@ -1,743 +0,0 @@
-
-/* Microcode patches for the CPM as supplied by Motorola.
- * This is the one for IIC/SPI.  There is a newer one that
- * also relocates SMC2, but this would require additional changes
- * to uart.c, so I am holding off on that for a moment.
- */
-#include <linux/errno.h>
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/param.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/interrupt.h>
-#include <asm/irq.h>
-#include <asm/mpc8xx.h>
-#include <asm/page.h>
-#include <asm/pgtable.h>
-#include <asm/8xx_immap.h>
-#include <asm/cpm1.h>
-
-/*
- * I2C/SPI relocation patch arrays.
- */
-
-#ifdef CONFIG_I2C_SPI_UCODE_PATCH
-
-uint patch_2000[] = {
-	0x7FFFEFD9,
-	0x3FFD0000,
-	0x7FFB49F7,
-	0x7FF90000,
-	0x5FEFADF7,
-	0x5F89ADF7,
-	0x5FEFAFF7,
-	0x5F89AFF7,
-	0x3A9CFBC8,
-	0xE7C0EDF0,
-	0x77C1E1BB,
-	0xF4DC7F1D,
-	0xABAD932F,
-	0x4E08FDCF,
-	0x6E0FAFF8,
-	0x7CCF76CF,
-	0xFD1FF9CF,
-	0xABF88DC6,
-	0xAB5679F7,
-	0xB0937383,
-	0xDFCE79F7,
-	0xB091E6BB,
-	0xE5BBE74F,
-	0xB3FA6F0F,
-	0x6FFB76CE,
-	0xEE0DF9CF,
-	0x2BFBEFEF,
-	0xCFEEF9CF,
-	0x76CEAD24,
-	0x90B2DF9A,
-	0x7FDDD0BF,
-	0x4BF847FD,
-	0x7CCF76CE,
-	0xCFEF7E1F,
-	0x7F1D7DFD,
-	0xF0B6EF71,
-	0x7FC177C1,
-	0xFBC86079,
-	0xE722FBC8,
-	0x5FFFDFFF,
-	0x5FB2FFFB,
-	0xFBC8F3C8,
-	0x94A67F01,
-	0x7F1D5F39,
-	0xAFE85F5E,
-	0xFFDFDF96,
-	0xCB9FAF7D,
-	0x5FC1AFED,
-	0x8C1C5FC1,
-	0xAFDD5FC3,
-	0xDF9A7EFD,
-	0xB0B25FB2,
-	0xFFFEABAD,
-	0x5FB2FFFE,
-	0x5FCE600B,
-	0xE6BB600B,
-	0x5FCEDFC6,
-	0x27FBEFDF,
-	0x5FC8CFDE,
-	0x3A9CE7C0,
-	0xEDF0F3C8,
-	0x7F0154CD,
-	0x7F1D2D3D,
-	0x363A7570,
-	0x7E0AF1CE,
-	0x37EF2E68,
-	0x7FEE10EC,
-	0xADF8EFDE,
-	0xCFEAE52F,
-	0x7D0FE12B,
-	0xF1CE5F65,
-	0x7E0A4DF8,
-	0xCFEA5F72,
-	0x7D0BEFEE,
-	0xCFEA5F74,
-	0xE522EFDE,
-	0x5F74CFDA,
-	0x0B627385,
-	0xDF627E0A,
-	0x30D8145B,
-	0xBFFFF3C8,
-	0x5FFFDFFF,
-	0xA7F85F5E,
-	0xBFFE7F7D,
-	0x10D31450,
-	0x5F36BFFF,
-	0xAF785F5E,
-	0xBFFDA7F8,
-	0x5F36BFFE,
-	0x77FD30C0,
-	0x4E08FDCF,
-	0xE5FF6E0F,
-	0xAFF87E1F,
-	0x7E0FFD1F,
-	0xF1CF5F1B,
-	0xABF80D5E,
-	0x5F5EFFEF,
-	0x79F730A2,
-	0xAFDD5F34,
-	0x47F85F34,
-	0xAFED7FDD,
-	0x50B24978,
-	0x47FD7F1D,
-	0x7DFD70AD,
-	0xEF717EC1,
-	0x6BA47F01,
-	0x2D267EFD,
-	0x30DE5F5E,
-	0xFFFD5F5E,
-	0xFFEF5F5E,
-	0xFFDF0CA0,
-	0xAFED0A9E,
-	0xAFDD0C3A,
-	0x5F3AAFBD,
-	0x7FBDB082,
-	0x5F8247F8
-};
-
-uint patch_2f00[] = {
-	0x3E303430,
-	0x34343737,
-	0xABF7BF9B,
-	0x994B4FBD,
-	0xBD599493,
-	0x349FFF37,
-	0xFB9B177D,
-	0xD9936956,
-	0xBBFDD697,
-	0xBDD2FD11,
-	0x31DB9BB3,
-	0x63139637,
-	0x93733693,
-	0x193137F7,
-	0x331737AF,
-	0x7BB9B999,
-	0xBB197957,
-	0x7FDFD3D5,
-	0x73B773F7,
-	0x37933B99,
-	0x1D115316,
-	0x99315315,
-	0x31694BF4,
-	0xFBDBD359,
-	0x31497353,
-	0x76956D69,
-	0x7B9D9693,
-	0x13131979,
-	0x79376935
-};
-#endif
-
-/*
- * I2C/SPI/SMC1 relocation patch arrays.
- */
-
-#ifdef CONFIG_I2C_SPI_SMC1_UCODE_PATCH
-
-uint patch_2000[] = {
-	0x3fff0000,
-	0x3ffd0000,
-	0x3ffb0000,
-	0x3ff90000,
-	0x5f13eff8,
-	0x5eb5eff8,
-	0x5f88adf7,
-	0x5fefadf7,
-	0x3a9cfbc8,
-	0x77cae1bb,
-	0xf4de7fad,
-	0xabae9330,
-	0x4e08fdcf,
-	0x6e0faff8,
-	0x7ccf76cf,
-	0xfdaff9cf,
-	0xabf88dc8,
-	0xab5879f7,
-	0xb0925d8d,
-	0xdfd079f7,
-	0xb090e6bb,
-	0xe5bbe74f,
-	0x9e046f0f,
-	0x6ffb76ce,
-	0xee0cf9cf,
-	0x2bfbefef,
-	0xcfeef9cf,
-	0x76cead23,
-	0x90b3df99,
-	0x7fddd0c1,
-	0x4bf847fd,
-	0x7ccf76ce,
-	0xcfef77ca,
-	0x7eaf7fad,
-	0x7dfdf0b7,
-	0xef7a7fca,
-	0x77cafbc8,
-	0x6079e722,
-	0xfbc85fff,
-	0xdfff5fb3,
-	0xfffbfbc8,
-	0xf3c894a5,
-	0xe7c9edf9,
-	0x7f9a7fad,
-	0x5f36afe8,
-	0x5f5bffdf,
-	0xdf95cb9e,
-	0xaf7d5fc3,
-	0xafed8c1b,
-	0x5fc3afdd,
-	0x5fc5df99,
-	0x7efdb0b3,
-	0x5fb3fffe,
-	0xabae5fb3,
-	0xfffe5fd0,
-	0x600be6bb,
-	0x600b5fd0,
-	0xdfc827fb,
-	0xefdf5fca,
-	0xcfde3a9c,
-	0xe7c9edf9,
-	0xf3c87f9e,
-	0x54ca7fed,
-	0x2d3a3637,
-	0x756f7e9a,
-	0xf1ce37ef,
-	0x2e677fee,
-	0x10ebadf8,
-	0xefdecfea,
-	0xe52f7d9f,
-	0xe12bf1ce,
-	0x5f647e9a,
-	0x4df8cfea,
-	0x5f717d9b,
-	0xefeecfea,
-	0x5f73e522,
-	0xefde5f73,
-	0xcfda0b61,
-	0x5d8fdf61,
-	0xe7c9edf9,
-	0x7e9a30d5,
-	0x1458bfff,
-	0xf3c85fff,
-	0xdfffa7f8,
-	0x5f5bbffe,
-	0x7f7d10d0,
-	0x144d5f33,
-	0xbfffaf78,
-	0x5f5bbffd,
-	0xa7f85f33,
-	0xbffe77fd,
-	0x30bd4e08,
-	0xfdcfe5ff,
-	0x6e0faff8,
-	0x7eef7e9f,
-	0xfdeff1cf,
-	0x5f17abf8,
-	0x0d5b5f5b,
-	0xffef79f7,
-	0x309eafdd,
-	0x5f3147f8,
-	0x5f31afed,
-	0x7fdd50af,
-	0x497847fd,
-	0x7f9e7fed,
-	0x7dfd70a9,
-	0xef7e7ece,
-	0x6ba07f9e,
-	0x2d227efd,
-	0x30db5f5b,
-	0xfffd5f5b,
-	0xffef5f5b,
-	0xffdf0c9c,
-	0xafed0a9a,
-	0xafdd0c37,
-	0x5f37afbd,
-	0x7fbdb081,
-	0x5f8147f8,
-	0x3a11e710,
-	0xedf0ccdd,
-	0xf3186d0a,
-	0x7f0e5f06,
-	0x7fedbb38,
-	0x3afe7468,
-	0x7fedf4fc,
-	0x8ffbb951,
-	0xb85f77fd,
-	0xb0df5ddd,
-	0xdefe7fed,
-	0x90e1e74d,
-	0x6f0dcbf7,
-	0xe7decfed,
-	0xcb74cfed,
-	0xcfeddf6d,
-	0x91714f74,
-	0x5dd2deef,
-	0x9e04e7df,
-	0xefbb6ffb,
-	0xe7ef7f0e,
-	0x9e097fed,
-	0xebdbeffa,
-	0xeb54affb,
-	0x7fea90d7,
-	0x7e0cf0c3,
-	0xbffff318,
-	0x5fffdfff,
-	0xac59efea,
-	0x7fce1ee5,
-	0xe2ff5ee1,
-	0xaffbe2ff,
-	0x5ee3affb,
-	0xf9cc7d0f,
-	0xaef8770f,
-	0x7d0fb0c6,
-	0xeffbbfff,
-	0xcfef5ede,
-	0x7d0fbfff,
-	0x5ede4cf8,
-	0x7fddd0bf,
-	0x49f847fd,
-	0x7efdf0bb,
-	0x7fedfffd,
-	0x7dfdf0b7,
-	0xef7e7e1e,
-	0x5ede7f0e,
-	0x3a11e710,
-	0xedf0ccab,
-	0xfb18ad2e,
-	0x1ea9bbb8,
-	0x74283b7e,
-	0x73c2e4bb,
-	0x2ada4fb8,
-	0xdc21e4bb,
-	0xb2a1ffbf,
-	0x5e2c43f8,
-	0xfc87e1bb,
-	0xe74ffd91,
-	0x6f0f4fe8,
-	0xc7ba32e2,
-	0xf396efeb,
-	0x600b4f78,
-	0xe5bb760b,
-	0x53acaef8,
-	0x4ef88b0e,
-	0xcfef9e09,
-	0xabf8751f,
-	0xefef5bac,
-	0x741f4fe8,
-	0x751e760d,
-	0x7fdbf081,
-	0x741cafce,
-	0xefcc7fce,
-	0x751e70ac,
-	0x741ce7bb,
-	0x3372cfed,
-	0xafdbefeb,
-	0xe5bb760b,
-	0x53f2aef8,
-	0xafe8e7eb,
-	0x4bf8771e,
-	0x7e247fed,
-	0x4fcbe2cc,
-	0x7fbc30a9,
-	0x7b0f7a0f,
-	0x34d577fd,
-	0x308b5db7,
-	0xde553e5f,
-	0xaf78741f,
-	0x741f30f0,
-	0xcfef5e2c,
-	0x741f3eac,
-	0xafb8771e,
-	0x5e677fed,
-	0x0bd3e2cc,
-	0x741ccfec,
-	0xe5ca53cd,
-	0x6fcb4f74,
-	0x5dadde4b,
-	0x2ab63d38,
-	0x4bb3de30,
-	0x751f741c,
-	0x6c42effa,
-	0xefea7fce,
-	0x6ffc30be,
-	0xefec3fca,
-	0x30b3de2e,
-	0xadf85d9e,
-	0xaf7daefd,
-	0x5d9ede2e,
-	0x5d9eafdd,
-	0x761f10ac,
-	0x1da07efd,
-	0x30adfffe,
-	0x4908fb18,
-	0x5fffdfff,
-	0xafbb709b,
-	0x4ef85e67,
-	0xadf814ad,
-	0x7a0f70ad,
-	0xcfef50ad,
-	0x7a0fde30,
-	0x5da0afed,
-	0x3c12780f,
-	0xefef780f,
-	0xefef790f,
-	0xa7f85e0f,
-	0xffef790f,
-	0xefef790f,
-	0x14adde2e,
-	0x5d9eadfd,
-	0x5e2dfffb,
-	0xe79addfd,
-	0xeff96079,
-	0x607ae79a,
-	0xddfceff9,
-	0x60795dff,
-	0x607acfef,
-	0xefefefdf,
-	0xefbfef7f,
-	0xeeffedff,
-	0xebffe7ff,
-	0xafefafdf,
-	0xafbfaf7f,
-	0xaeffadff,
-	0xabffa7ff,
-	0x6fef6fdf,
-	0x6fbf6f7f,
-	0x6eff6dff,
-	0x6bff67ff,
-	0x2fef2fdf,
-	0x2fbf2f7f,
-	0x2eff2dff,
-	0x2bff27ff,
-	0x4e08fd1f,
-	0xe5ff6e0f,
-	0xaff87eef,
-	0x7e0ffdef,
-	0xf11f6079,
-	0xabf8f542,
-	0x7e0af11c,
-	0x37cfae3a,
-	0x7fec90be,
-	0xadf8efdc,
-	0xcfeae52f,
-	0x7d0fe12b,
-	0xf11c6079,
-	0x7e0a4df8,
-	0xcfea5dc4,
-	0x7d0befec,
-	0xcfea5dc6,
-	0xe522efdc,
-	0x5dc6cfda,
-	0x4e08fd1f,
-	0x6e0faff8,
-	0x7c1f761f,
-	0xfdeff91f,
-	0x6079abf8,
-	0x761cee24,
-	0xf91f2bfb,
-	0xefefcfec,
-	0xf91f6079,
-	0x761c27fb,
-	0xefdf5da7,
-	0xcfdc7fdd,
-	0xd09c4bf8,
-	0x47fd7c1f,
-	0x761ccfcf,
-	0x7eef7fed,
-	0x7dfdf093,
-	0xef7e7f1e,
-	0x771efb18,
-	0x6079e722,
-	0xe6bbe5bb,
-	0xae0ae5bb,
-	0x600bae85,
-	0xe2bbe2bb,
-	0xe2bbe2bb,
-	0xaf02e2bb,
-	0xe2bb2ff9,
-	0x6079e2bb
-};
-
-uint patch_2f00[] = {
-	0x30303030,
-	0x3e3e3434,
-	0xabbf9b99,
-	0x4b4fbdbd,
-	0x59949334,
-	0x9fff37fb,
-	0x9b177dd9,
-	0x936956bb,
-	0xfbdd697b,
-	0xdd2fd113,
-	0x1db9f7bb,
-	0x36313963,
-	0x79373369,
-	0x3193137f,
-	0x7331737a,
-	0xf7bb9b99,
-	0x9bb19795,
-	0x77fdfd3d,
-	0x573b773f,
-	0x737933f7,
-	0xb991d115,
-	0x31699315,
-	0x31531694,
-	0xbf4fbdbd,
-	0x35931497,
-	0x35376956,
-	0xbd697b9d,
-	0x96931313,
-	0x19797937,
-	0x6935af78,
-	0xb9b3baa3,
-	0xb8788683,
-	0x368f78f7,
-	0x87778733,
-	0x3ffffb3b,
-	0x8e8f78b8,
-	0x1d118e13,
-	0xf3ff3f8b,
-	0x6bd8e173,
-	0xd1366856,
-	0x68d1687b,
-	0x3daf78b8,
-	0x3a3a3f87,
-	0x8f81378f,
-	0xf876f887,
-	0x77fd8778,
-	0x737de8d6,
-	0xbbf8bfff,
-	0xd8df87f7,
-	0xfd876f7b,
-	0x8bfff8bd,
-	0x8683387d,
-	0xb873d87b,
-	0x3b8fd7f8,
-	0xf7338883,
-	0xbb8ee1f8,
-	0xef837377,
-	0x3337b836,
-	0x817d11f8,
-	0x7378b878,
-	0xd3368b7d,
-	0xed731b7d,
-	0x833731f3,
-	0xf22f3f23
-};
-
-uint patch_2e00[] = {
-	0x27eeeeee,
-	0xeeeeeeee,
-	0xeeeeeeee,
-	0xeeeeeeee,
-	0xee4bf4fb,
-	0xdbd259bb,
-	0x1979577f,
-	0xdfd2d573,
-	0xb773f737,
-	0x4b4fbdbd,
-	0x25b9b177,
-	0xd2d17376,
-	0x956bbfdd,
-	0x697bdd2f,
-	0xff9f79ff,
-	0xff9ff22f
-};
-#endif
-
-/*
- *  USB SOF patch arrays.
- */
-
-#ifdef CONFIG_USB_SOF_UCODE_PATCH
-
-uint patch_2000[] = {
-	0x7fff0000,
-	0x7ffd0000,
-	0x7ffb0000,
-	0x49f7ba5b,
-	0xba383ffb,
-	0xf9b8b46d,
-	0xe5ab4e07,
-	0xaf77bffe,
-	0x3f7bbf79,
-	0xba5bba38,
-	0xe7676076,
-	0x60750000
-};
-
-uint patch_2f00[] = {
-	0x3030304c,
-	0xcab9e441,
-	0xa1aaf220
-};
-#endif
-
-void
-cpm_load_patch(volatile immap_t *immr)
-{
-	volatile uint		*dp;		/* Dual-ported RAM. */
-	volatile cpm8xx_t	*commproc;
-	volatile iic_t		*iip;
-	volatile spi_t		*spp;
-	volatile smc_uart_t	*smp;
-	int	i;
-
-	commproc = (cpm8xx_t *)&immr->im_cpm;
-
-#ifdef CONFIG_USB_SOF_UCODE_PATCH
-	commproc->cp_rccr = 0;
-
-	dp = (uint *)(commproc->cp_dpmem);
-	for (i=0; i<(sizeof(patch_2000)/4); i++)
-		*dp++ = patch_2000[i];
-
-	dp = (uint *)&(commproc->cp_dpmem[0x0f00]);
-	for (i=0; i<(sizeof(patch_2f00)/4); i++)
-		*dp++ = patch_2f00[i];
-
-	commproc->cp_rccr = 0x0009;
-
-	printk("USB SOF microcode patch installed\n");
-#endif /* CONFIG_USB_SOF_UCODE_PATCH */
-
-#if defined(CONFIG_I2C_SPI_UCODE_PATCH) || \
-    defined(CONFIG_I2C_SPI_SMC1_UCODE_PATCH)
-
-	commproc->cp_rccr = 0;
-
-	dp = (uint *)(commproc->cp_dpmem);
-	for (i=0; i<(sizeof(patch_2000)/4); i++)
-		*dp++ = patch_2000[i];
-
-	dp = (uint *)&(commproc->cp_dpmem[0x0f00]);
-	for (i=0; i<(sizeof(patch_2f00)/4); i++)
-		*dp++ = patch_2f00[i];
-
-	iip = (iic_t *)&commproc->cp_dparam[PROFF_IIC];
-# define RPBASE 0x0500
-	iip->iic_rpbase = RPBASE;
-
-	/* Put SPI above the IIC, also 32-byte aligned.
-	*/
-	i = (RPBASE + sizeof(iic_t) + 31) & ~31;
-	spp = (spi_t *)&commproc->cp_dparam[PROFF_SPI];
-	spp->spi_rpbase = i;
-
-# if defined(CONFIG_I2C_SPI_UCODE_PATCH)
-	commproc->cp_cpmcr1 = 0x802a;
-	commproc->cp_cpmcr2 = 0x8028;
-	commproc->cp_cpmcr3 = 0x802e;
-	commproc->cp_cpmcr4 = 0x802c;
-	commproc->cp_rccr = 1;
-
-	printk("I2C/SPI microcode patch installed.\n");
-# endif /* CONFIG_I2C_SPI_UCODE_PATCH */
-
-# if defined(CONFIG_I2C_SPI_SMC1_UCODE_PATCH)
-
-	dp = (uint *)&(commproc->cp_dpmem[0x0e00]);
-	for (i=0; i<(sizeof(patch_2e00)/4); i++)
-		*dp++ = patch_2e00[i];
-
-	commproc->cp_cpmcr1 = 0x8080;
-	commproc->cp_cpmcr2 = 0x808a;
-	commproc->cp_cpmcr3 = 0x8028;
-	commproc->cp_cpmcr4 = 0x802a;
-	commproc->cp_rccr = 3;
-
-	smp = (smc_uart_t *)&commproc->cp_dparam[PROFF_SMC1];
-	smp->smc_rpbase = 0x1FC0;
-
-	printk("I2C/SPI/SMC1 microcode patch installed.\n");
-# endif /* CONFIG_I2C_SPI_SMC1_UCODE_PATCH) */
-
-#endif /* some variation of the I2C/SPI patch was selected */
-}
-
-/*
- *  Take this entire routine out, since no one calls it and its 
- * logic is suspect.
- */
-
-#if 0
-void
-verify_patch(volatile immap_t *immr)
-{
-	volatile uint		*dp;
-	volatile cpm8xx_t	*commproc;
-	int i;
-
-	commproc = (cpm8xx_t *)&immr->im_cpm;
-
-	printk("cp_rccr %x\n", commproc->cp_rccr);
-	commproc->cp_rccr = 0;
-
-	dp = (uint *)(commproc->cp_dpmem);
-	for (i=0; i<(sizeof(patch_2000)/4); i++)
-		if (*dp++ != patch_2000[i]) {
-			printk("patch_2000 bad at %d\n", i);
-			dp--;
-			printk("found 0x%X, wanted 0x%X\n", *dp, patch_2000[i]);
-			break;
-		}
-
-	dp = (uint *)&(commproc->cp_dpmem[0x0f00]);
-	for (i=0; i<(sizeof(patch_2f00)/4); i++)
-		if (*dp++ != patch_2f00[i]) {
-			printk("patch_2f00 bad at %d\n", i);
-			dp--;
-			printk("found 0x%X, wanted 0x%X\n", *dp, patch_2f00[i]);
-			break;
-		}
-
-	commproc->cp_rccr = 0x0009;
-}
-#endif