Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 227 insertions, 0 deletions

diff --git a/arch/ppc/platforms/85xx/sbc8560.c b/arch/ppc/platforms/85xx/sbc8560.c
new file mode 100644
index 00000000000..9ab05e590c3
--- /dev/null
+++ b/arch/ppc/platforms/85xx/sbc8560.c
@@ -0,0 +1,227 @@
+/*
+ * arch/ppc/platforms/85xx/sbc8560.c
+ * 
+ * Wind River SBC8560 board specific routines
+ * 
+ * Maintainer: Kumar Gala <kumar.gala@freescale.com>
+ *
+ * Copyright 2004 Freescale Semiconductor Inc.
+ * 
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/major.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/serial.h>
+#include <linux/tty.h>	/* for linux/serial_core.h */
+#include <linux/serial_core.h>
+#include <linux/initrd.h>
+#include <linux/module.h>
+#include <linux/fsl_devices.h>
+
+#include <asm/system.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/atomic.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/open_pic.h>
+#include <asm/bootinfo.h>
+#include <asm/pci-bridge.h>
+#include <asm/mpc85xx.h>
+#include <asm/irq.h>
+#include <asm/immap_85xx.h>
+#include <asm/kgdb.h>
+#include <asm/ppc_sys.h>
+#include <mm/mmu_decl.h>
+
+#include <syslib/ppc85xx_common.h>
+#include <syslib/ppc85xx_setup.h>
+
+#ifdef CONFIG_SERIAL_8250
+static void __init
+sbc8560_early_serial_map(void)
+{
+        struct uart_port uart_req;
+ 
+        /* Setup serial port access */
+        memset(&uart_req, 0, sizeof (uart_req));
+	uart_req.irq = MPC85xx_IRQ_EXT9;
+	uart_req.flags = STD_COM_FLAGS;
+	uart_req.uartclk = BASE_BAUD * 16;
+        uart_req.iotype = SERIAL_IO_MEM;
+        uart_req.mapbase = UARTA_ADDR;
+        uart_req.membase = ioremap(uart_req.mapbase, MPC85xx_UART0_SIZE);
+	uart_req.type = PORT_16650;
+
+#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB)
+        gen550_init(0, &uart_req);
+#endif
+ 
+        if (early_serial_setup(&uart_req) != 0)
+                printk("Early serial init of port 0 failed\n");
+ 
+        /* Assume early_serial_setup() doesn't modify uart_req */
+	uart_req.line = 1;
+        uart_req.mapbase = UARTB_ADDR;
+        uart_req.membase = ioremap(uart_req.mapbase, MPC85xx_UART1_SIZE);
+	uart_req.irq = MPC85xx_IRQ_EXT10;
+ 
+#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB)
+        gen550_init(1, &uart_req);
+#endif
+ 
+        if (early_serial_setup(&uart_req) != 0)
+                printk("Early serial init of port 1 failed\n");
+}
+#endif
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init
+sbc8560_setup_arch(void)
+{
+	bd_t *binfo = (bd_t *) __res;
+	unsigned int freq;
+	struct gianfar_platform_data *pdata;
+
+	/* get the core frequency */
+	freq = binfo->bi_intfreq;
+
+	if (ppc_md.progress)
+		ppc_md.progress("sbc8560_setup_arch()", 0);
+
+	/* Set loops_per_jiffy to a half-way reasonable value,
+	   for use until calibrate_delay gets called. */
+	loops_per_jiffy = freq / HZ;
+
+#ifdef CONFIG_PCI
+	/* setup PCI host bridges */
+	mpc85xx_setup_hose();
+#endif
+#ifdef CONFIG_SERIAL_8250
+	sbc8560_early_serial_map();
+#endif
+#ifdef CONFIG_SERIAL_TEXT_DEBUG
+	/* Invalidate the entry we stole earlier the serial ports
+	 * should be properly mapped */ 
+	invalidate_tlbcam_entry(NUM_TLBCAMS - 1);
+#endif
+
+	/* setup the board related information for the enet controllers */
+	pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC1);
+	pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
+	pdata->interruptPHY = MPC85xx_IRQ_EXT6;
+	pdata->phyid = 25;
+	/* fixup phy address */
+	pdata->phy_reg_addr += binfo->bi_immr_base;
+	memcpy(pdata->mac_addr, binfo->bi_enetaddr, 6);
+
+	pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC2);
+	pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
+	pdata->interruptPHY = MPC85xx_IRQ_EXT7;
+	pdata->phyid = 26;
+	/* fixup phy address */
+	pdata->phy_reg_addr += binfo->bi_immr_base;
+	memcpy(pdata->mac_addr, binfo->bi_enet1addr, 6);
+
+#ifdef CONFIG_BLK_DEV_INITRD
+	if (initrd_start)
+		ROOT_DEV = Root_RAM0;
+	else
+#endif
+#ifdef  CONFIG_ROOT_NFS
+		ROOT_DEV = Root_NFS;
+#else
+		ROOT_DEV = Root_HDA1;
+#endif
+}
+
+/* ************************************************************************ */
+void __init
+platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+	      unsigned long r6, unsigned long r7)
+{
+	/* parse_bootinfo must always be called first */
+	parse_bootinfo(find_bootinfo());
+
+	/*
+	 * If we were passed in a board information, copy it into the
+	 * residual data area.
+	 */
+	if (r3) {
+		memcpy((void *) __res, (void *) (r3 + KERNELBASE),
+		       sizeof (bd_t));
+	}
+
+#ifdef CONFIG_SERIAL_TEXT_DEBUG
+	/* Use the last TLB entry to map CCSRBAR to allow access to DUART regs */
+	settlbcam(NUM_TLBCAMS - 1, UARTA_ADDR,
+		  UARTA_ADDR, 0x1000, _PAGE_IO, 0);
+#endif
+
+#if defined(CONFIG_BLK_DEV_INITRD)
+	/*
+	 * If the init RAM disk has been configured in, and there's a valid
+	 * starting address for it, set it up.
+	 */
+	if (r4) {
+		initrd_start = r4 + KERNELBASE;
+		initrd_end = r5 + KERNELBASE;
+	}
+#endif				/* CONFIG_BLK_DEV_INITRD */
+
+	/* Copy the kernel command line arguments to a safe place. */
+
+	if (r6) {
+		*(char *) (r7 + KERNELBASE) = 0;
+		strcpy(cmd_line, (char *) (r6 + KERNELBASE));
+	}
+
+	identify_ppc_sys_by_id(mfspr(SPRN_SVR));
+
+	/* setup the PowerPC module struct */
+	ppc_md.setup_arch = sbc8560_setup_arch;
+	ppc_md.show_cpuinfo = sbc8560_show_cpuinfo;
+
+	ppc_md.init_IRQ = sbc8560_init_IRQ;
+	ppc_md.get_irq = openpic_get_irq;
+
+	ppc_md.restart = mpc85xx_restart;
+	ppc_md.power_off = mpc85xx_power_off;
+	ppc_md.halt = mpc85xx_halt;
+
+	ppc_md.find_end_of_memory = mpc85xx_find_end_of_memory;
+
+	ppc_md.time_init = NULL;
+	ppc_md.set_rtc_time = NULL;
+	ppc_md.get_rtc_time = NULL;
+	ppc_md.calibrate_decr = mpc85xx_calibrate_decr;
+
+#if defined(CONFIG_SERIAL_8250) && defined(CONFIG_SERIAL_TEXT_DEBUG)
+	ppc_md.progress = gen550_progress;
+#endif	/* CONFIG_SERIAL_8250 && CONFIG_SERIAL_TEXT_DEBUG */
+
+	if (ppc_md.progress)
+		ppc_md.progress("sbc8560_init(): exit", 0);
+}