sh: remove voyagergx

This patch removes redundant irq handling code together with unused
consistent alloc code. R2D uart setup code is changed to use
sm501-regs.h and unused header files are removed.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

1 files changed, 39 insertions, 34 deletions

diff --git a/arch/sh/boards/renesas/rts7751r2d/setup.c b/arch/sh/boards/renesas/rts7751r2d/setup.c
index dc143c10cd1..8cb49661707 100644
--- a/arch/sh/boards/renesas/rts7751r2d/setup.c
+++ b/arch/sh/boards/renesas/rts7751r2d/setup.c
@@ -13,36 +13,13 @@
 #include <linux/pata_platform.h>
 #include <linux/serial_8250.h>
 #include <linux/sm501.h>
+#include <linux/sm501-regs.h>
 #include <linux/pm.h>
 #include <linux/fb.h>
 #include <asm/machvec.h>
 #include <asm/rts7751r2d.h>
-#include <asm/voyagergx.h>
 #include <asm/io.h>
 
-static void __init voyagergx_serial_init(void)
-{
-	unsigned long val;
-
-	/*
-	 * GPIO Control
-	 */
-	val = readl((void __iomem *)GPIO_MUX_HIGH);
-	val |= 0x00001fe0;
-	writel(val, (void __iomem *)GPIO_MUX_HIGH);
-
-	/*
-	 * Power Mode Gate
-	 */
-	val = readl((void __iomem *)POWER_MODE0_GATE);
-	val |= (POWER_MODE0_GATE_U0 | POWER_MODE0_GATE_U1);
-	writel(val, (void __iomem *)POWER_MODE0_GATE);
-
-	val = readl((void __iomem *)POWER_MODE1_GATE);
-	val |= (POWER_MODE1_GATE_U0 | POWER_MODE1_GATE_U1);
-	writel(val, (void __iomem *)POWER_MODE1_GATE);
-}
-
 static struct resource cf_ide_resources[] = {
 	[0] = {
 		.start	= PA_AREA5_IO + 0x1000,
@@ -94,11 +71,11 @@ static struct platform_device heartbeat_device = {
 #ifdef CONFIG_MFD_SM501
 static struct plat_serial8250_port uart_platform_data[] = {
 	{
-		.membase	= (void __iomem *)VOYAGER_UART_BASE,
-		.mapbase	= VOYAGER_UART_BASE,
+		.membase	= (void __iomem *)0xb3e30000,
+		.mapbase	= 0xb3e30000,
 		.iotype		= UPIO_MEM,
-		.irq		= IRQ_SM501_U0,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.irq		= IRQ_VOYAGER,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ,
 		.regshift	= 2,
 		.uartclk	= (9600 * 16),
 	},
@@ -125,7 +102,7 @@ static struct resource sm501_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[2]	= {
-		.start	= IRQ_SM501_CV,
+		.start	= IRQ_VOYAGER,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -167,7 +144,15 @@ static struct sm501_platdata_fb sm501_fb_pdata = {
 	.flags		= SM501_FBPD_SWAP_FB_ENDIAN,
 };
 
+static struct sm501_initdata sm501_initdata = {
+	.gpio_high	= {
+		.set	= 0x00001fe0,
+		.mask	= 0x0,
+	},
+};
+
 static struct sm501_platdata sm501_platform_data = {
+	.init		= &sm501_initdata,
 	.fb		= &sm501_fb_pdata,
 };
 
@@ -237,6 +222,7 @@ u8 rts7751r2d_readb(void __iomem *addr)
  */
 static void __init rts7751r2d_setup(char **cmdline_p)
 {
+	void __iomem *sm501_reg;
 	u16 ver = ctrl_inw(PA_VERREG);
 
 	printk(KERN_INFO "Renesas Technology Sales RTS7751R2D support.\n");
@@ -247,7 +233,30 @@ static void __init rts7751r2d_setup(char **cmdline_p)
 	ctrl_outw(0x0000, PA_OUTPORT);
 	pm_power_off = rts7751r2d_power_off;
 
-	voyagergx_serial_init();
+	/* sm501 dram configuration:
+	 * ColSizeX = 11 - External Memory Column Size: 256 words.
+	 * APX = 1 - External Memory Active to Pre-Charge Delay: 7 clocks.
+	 * RstX = 1 - External Memory Reset: Normal.
+	 * Rfsh = 1 - Local Memory Refresh to Command Delay: 12 clocks.
+	 * BwC =  1 - Local Memory Block Write Cycle Time: 2 clocks.
+	 * BwP =  1 - Local Memory Block Write to Pre-Charge Delay: 1 clock.
+	 * AP = 1 - Internal Memory Active to Pre-Charge Delay: 7 clocks.
+	 * Rst = 1 - Internal Memory Reset: Normal.
+	 * RA = 1 - Internal Memory Remain in Active State: Do not remain.
+	 */
+
+	sm501_reg = (void __iomem *)0xb3e00000 + SM501_DRAM_CONTROL;
+	writel(readl(sm501_reg) | 0x00f107c0, sm501_reg);
+
+	/*
+	 * Power Mode Gate - Enable UART0
+	 */
+
+	sm501_reg = (void __iomem *)0xb3e00000 + SM501_POWER_MODE_0_GATE;
+	writel(readl(sm501_reg) | (1 << SM501_GATE_UART0), sm501_reg);
+
+	sm501_reg = (void __iomem *)0xb3e00000 + SM501_POWER_MODE_1_GATE;
+	writel(readl(sm501_reg) | (1 << SM501_GATE_UART0), sm501_reg);
 }
 
 /*
@@ -260,8 +269,4 @@ static struct sh_machine_vector mv_rts7751r2d __initmv = {
 	.mv_irq_demux		= rts7751r2d_irq_demux,
 	.mv_writeb		= rts7751r2d_writeb,
 	.mv_readb		= rts7751r2d_readb,
-#if defined(CONFIG_MFD_SM501) && defined(CONFIG_USB_OHCI_HCD)
-	.mv_consistent_alloc	= voyagergx_consistent_alloc,
-	.mv_consistent_free	= voyagergx_consistent_free,
-#endif
 };