sh: migrate to arch/sh/include/

This follows the sparc changes a439fe51a1f8eb087c22dd24d69cebae4a3addac.

Most of the moving about was done with Sam's directions at:

http://marc.info/?l=linux-sh&m=121724823706062&w=2

with subsequent hacking and fixups entirely my fault.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

1 files changed, 190 insertions, 0 deletions

diff --git a/arch/sh/include/asm/smc37c93x.h b/arch/sh/include/asm/smc37c93x.h
new file mode 100644
index 00000000000..585da2a8fc4
--- /dev/null
+++ b/arch/sh/include/asm/smc37c93x.h
@@ -0,0 +1,190 @@
+#ifndef __ASM_SH_SMC37C93X_H
+#define __ASM_SH_SMC37C93X_H
+
+/*
+ * linux/include/asm-sh/smc37c93x.h
+ *
+ * Copyright (C) 2000  Kazumoto Kojima
+ *
+ * SMSC 37C93x Super IO Chip support
+ */
+
+/* Default base I/O address */
+#define FDC_PRIMARY_BASE	0x3f0
+#define IDE1_PRIMARY_BASE	0x1f0
+#define IDE1_SECONDARY_BASE	0x170
+#define PARPORT_PRIMARY_BASE	0x378
+#define COM1_PRIMARY_BASE	0x2f8
+#define COM2_PRIMARY_BASE	0x3f8
+#define RTC_PRIMARY_BASE	0x070
+#define KBC_PRIMARY_BASE	0x060
+#define AUXIO_PRIMARY_BASE	0x000	/* XXX */
+
+/* Logical device number */
+#define LDN_FDC			0
+#define LDN_IDE1		1
+#define LDN_IDE2		2
+#define LDN_PARPORT		3
+#define LDN_COM1		4
+#define LDN_COM2		5
+#define LDN_RTC			6
+#define LDN_KBC			7
+#define LDN_AUXIO		8
+
+/* Configuration port and key */
+#define CONFIG_PORT		0x3f0
+#define INDEX_PORT		CONFIG_PORT
+#define DATA_PORT		0x3f1
+#define CONFIG_ENTER		0x55
+#define CONFIG_EXIT		0xaa
+
+/* Configuration index */
+#define CURRENT_LDN_INDEX	0x07
+#define POWER_CONTROL_INDEX	0x22
+#define ACTIVATE_INDEX		0x30
+#define IO_BASE_HI_INDEX	0x60
+#define IO_BASE_LO_INDEX	0x61
+#define IRQ_SELECT_INDEX	0x70
+#define DMA_SELECT_INDEX	0x74
+
+#define GPIO46_INDEX		0xc6
+#define GPIO47_INDEX		0xc7
+
+/* UART stuff. Only for debugging.  */
+/* UART Register */
+
+#define UART_RBR	0x0	/* Receiver Buffer Register (Read Only) */
+#define UART_THR	0x0	/* Transmitter Holding Register (Write Only) */
+#define UART_IER	0x2	/* Interrupt Enable Register */
+#define UART_IIR	0x4	/* Interrupt Ident Register (Read Only) */
+#define UART_FCR	0x4	/* FIFO Control Register (Write Only) */
+#define UART_LCR	0x6	/* Line Control Register */
+#define UART_MCR	0x8	/* MODEM Control Register */
+#define UART_LSR	0xa	/* Line Status Register */
+#define UART_MSR	0xc	/* MODEM Status Register */
+#define UART_SCR	0xe	/* Scratch Register */
+#define UART_DLL	0x0	/* Divisor Latch (LS) */
+#define UART_DLM	0x2	/* Divisor Latch (MS) */
+
+#ifndef __ASSEMBLY__
+typedef struct uart_reg {
+	volatile __u16 rbr;
+	volatile __u16 ier;
+	volatile __u16 iir;
+	volatile __u16 lcr;
+	volatile __u16 mcr;
+	volatile __u16 lsr;
+	volatile __u16 msr;
+	volatile __u16 scr;
+} uart_reg;
+#endif /* ! __ASSEMBLY__ */
+
+/* Alias for Write Only Register */
+
+#define thr	rbr
+#define tcr	iir
+
+/* Alias for Divisor Latch Register */
+
+#define dll	rbr
+#define dlm	ier
+#define fcr	iir
+
+/* Interrupt Enable Register */
+
+#define IER_ERDAI	0x0100	/* Enable Received Data Available Interrupt */
+#define IER_ETHREI	0x0200	/* Enable Transmitter Holding Register Empty Interrupt */
+#define IER_ELSI	0x0400	/* Enable Receiver Line Status Interrupt */
+#define IER_EMSI	0x0800	/* Enable MODEM Status Interrupt */
+
+/* Interrupt Ident Register */
+
+#define IIR_IP		0x0100	/* "0" if Interrupt Pending */
+#define IIR_IIB0	0x0200	/* Interrupt ID Bit 0 */
+#define IIR_IIB1	0x0400	/* Interrupt ID Bit 1 */
+#define IIR_IIB2	0x0800	/* Interrupt ID Bit 2 */
+#define IIR_FIFO	0xc000	/* FIFOs enabled */
+
+/* FIFO Control Register */
+
+#define FCR_FEN		0x0100	/* FIFO enable */
+#define FCR_RFRES	0x0200	/* Receiver FIFO reset */
+#define FCR_TFRES	0x0400	/* Transmitter FIFO reset */
+#define FCR_DMA		0x0800	/* DMA mode select */
+#define FCR_RTL		0x4000	/* Receiver triger (LSB) */
+#define FCR_RTM		0x8000	/* Receiver triger (MSB) */
+
+/* Line Control Register */
+
+#define LCR_WLS0	0x0100	/* Word Length Select Bit 0 */
+#define LCR_WLS1	0x0200	/* Word Length Select Bit 1 */
+#define LCR_STB		0x0400	/* Number of Stop Bits */
+#define LCR_PEN		0x0800	/* Parity Enable */
+#define LCR_EPS		0x1000	/* Even Parity Select */
+#define LCR_SP		0x2000	/* Stick Parity */
+#define LCR_SB		0x4000	/* Set Break */
+#define LCR_DLAB	0x8000	/* Divisor Latch Access Bit */
+
+/* MODEM Control Register */
+
+#define MCR_DTR		0x0100	/* Data Terminal Ready */
+#define MCR_RTS		0x0200	/* Request to Send */
+#define MCR_OUT1	0x0400	/* Out 1 */
+#define MCR_IRQEN	0x0800	/* IRQ Enable */
+#define MCR_LOOP	0x1000	/* Loop */
+
+/* Line Status Register */
+
+#define LSR_DR		0x0100	/* Data Ready */
+#define LSR_OE		0x0200	/* Overrun Error */
+#define LSR_PE		0x0400	/* Parity Error */
+#define LSR_FE		0x0800	/* Framing Error */
+#define LSR_BI		0x1000	/* Break Interrupt */
+#define LSR_THRE	0x2000	/* Transmitter Holding Register Empty */
+#define LSR_TEMT	0x4000	/* Transmitter Empty */
+#define LSR_FIFOE	0x8000	/* Receiver FIFO error */
+
+/* MODEM Status Register */
+
+#define MSR_DCTS	0x0100	/* Delta Clear to Send */
+#define MSR_DDSR	0x0200	/* Delta Data Set Ready */
+#define MSR_TERI	0x0400	/* Trailing Edge Ring Indicator */
+#define MSR_DDCD	0x0800	/* Delta Data Carrier Detect */
+#define MSR_CTS		0x1000	/* Clear to Send */
+#define MSR_DSR		0x2000	/* Data Set Ready */
+#define MSR_RI		0x4000	/* Ring Indicator */
+#define MSR_DCD		0x8000	/* Data Carrier Detect */
+
+/* Baud Rate Divisor */
+
+#define UART_CLK	(1843200)	/* 1.8432 MHz */
+#define UART_BAUD(x)	(UART_CLK / (16 * (x)))
+
+/* RTC register definition */
+#define RTC_SECONDS             0
+#define RTC_SECONDS_ALARM       1
+#define RTC_MINUTES             2
+#define RTC_MINUTES_ALARM       3
+#define RTC_HOURS               4
+#define RTC_HOURS_ALARM         5
+#define RTC_DAY_OF_WEEK         6
+#define RTC_DAY_OF_MONTH        7
+#define RTC_MONTH               8
+#define RTC_YEAR                9
+#define RTC_FREQ_SELECT		10
+# define RTC_UIP 0x80
+# define RTC_DIV_CTL 0x70
+/* This RTC can work under 32.768KHz clock only.  */
+# define RTC_OSC_ENABLE 0x20
+# define RTC_OSC_DISABLE 0x00
+#define RTC_CONTROL     	11
+# define RTC_SET 0x80
+# define RTC_PIE 0x40
+# define RTC_AIE 0x20
+# define RTC_UIE 0x10
+# define RTC_SQWE 0x08
+# define RTC_DM_BINARY 0x04
+# define RTC_24H 0x02
+# define RTC_DST_EN 0x01
+
+#endif  /* __ASM_SH_SMC37C93X_H */