Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

power management changes for omap and imx

A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.

* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
  ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
  ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
  ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
  ARM: imx6q: build pm code only when CONFIG_PM selected
  ARM: mx5: use generic irq chip pm interface for pm functions on
  ARM: omap: pass minimal SoC/board data for UART from dt
  arm/dts: Add minimal device tree support for omap2420 and omap2430
  omap-serial: Add minimal device tree support
  omap-serial: Use default clock speed (48Mhz) if not specified
  omap-serial: Get rid of all pdev->id usage
  ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
  ARM: OMAP4: PRM: use PRCM interrupt handler
  ARM: OMAP3: pm: use prcm chain handler
  ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
  ARM: OMAP2+: mux: add support for PAD wakeup interrupts
  ARM: OMAP: PRCM: add suspend prepare / finish support
  ARM: OMAP: PRCM: add support for chain interrupt handler
  ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
  ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
  ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
  ...

57 files changed, 3494 insertions, 1119 deletions

diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
new file mode 100644
index 00000000000..f2ab4ea7cc0
--- /dev/null
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -0,0 +1,67 @@
+/*
+ * Device Tree Source for OMAP2 SoC
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "ti,omap2430", "ti,omap2420", "ti,omap2";
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+	};
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,arm1136jf-s";
+		};
+	};
+
+	soc {
+		compatible = "ti,omap-infra";
+		mpu {
+			compatible = "ti,omap2-mpu";
+			ti,hwmods = "mpu";
+		};
+	};
+
+	ocp {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		ti,hwmods = "l3_main";
+
+		intc: interrupt-controller@1 {
+			compatible = "ti,omap2-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		uart1: serial@4806a000 {
+			compatible = "ti,omap2-uart";
+			ti,hwmods = "uart1";
+			clock-frequency = <48000000>;
+		};
+
+		uart2: serial@4806c000 {
+			compatible = "ti,omap2-uart";
+			ti,hwmods = "uart2";
+			clock-frequency = <48000000>;
+		};
+
+		uart3: serial@4806e000 {
+			compatible = "ti,omap2-uart";
+			ti,hwmods = "uart3";
+			clock-frequency = <48000000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index d202bb5ec7e..216c3317461 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -13,6 +13,13 @@
 / {
 	compatible = "ti,omap3430", "ti,omap3";
 
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+	};
+
 	cpus {
 		cpu@0 {
 			compatible = "arm,cortex-a8";
@@ -59,5 +66,29 @@
 			interrupt-controller;
 			#interrupt-cells = <1>;
 		};
+
+		uart1: serial@0x4806a000 {
+			compatible = "ti,omap3-uart";
+			ti,hwmods = "uart1";
+			clock-frequency = <48000000>;
+		};
+
+		uart2: serial@0x4806c000 {
+			compatible = "ti,omap3-uart";
+			ti,hwmods = "uart2";
+			clock-frequency = <48000000>;
+		};
+
+		uart3: serial@0x49020000 {
+			compatible = "ti,omap3-uart";
+			ti,hwmods = "uart3";
+			clock-frequency = <48000000>;
+		};
+
+		uart4: serial@0x49042000 {
+			compatible = "ti,omap3-uart";
+			ti,hwmods = "uart4";
+			clock-frequency = <48000000>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 4c61c829043..e8fe75fac7c 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -21,6 +21,10 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
 	};
 
 	cpus {
@@ -99,5 +103,29 @@
 			reg = <0x48241000 0x1000>,
 			      <0x48240100 0x0100>;
 		};
+
+		uart1: serial@0x4806a000 {
+			compatible = "ti,omap4-uart";
+			ti,hwmods = "uart1";
+			clock-frequency = <48000000>;
+		};
+
+		uart2: serial@0x4806c000 {
+			compatible = "ti,omap4-uart";
+			ti,hwmods = "uart2";
+			clock-frequency = <48000000>;
+		};
+
+		uart3: serial@0x48020000 {
+			compatible = "ti,omap4-uart";
+			ti,hwmods = "uart3";
+			clock-frequency = <48000000>;
+		};
+
+		uart4: serial@0x4806e000 {
+			compatible = "ti,omap4-uart";
+			ti,hwmods = "uart4";
+			clock-frequency = <48000000>;
+		};
 	};
 };
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 9d8598f29fd..0e6de366c64 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -596,6 +596,7 @@ comment "i.MX6 family:"
 
 config SOC_IMX6Q
 	bool "i.MX6 Quad support"
+	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
 	select CPU_V7
 	select HAVE_ARM_SCU
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index d97f409ce98..f5920c24f7d 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -70,4 +70,8 @@ AFLAGS_head-v7.o :=-Wa,-march=armv7-a
 obj-$(CONFIG_SMP) += platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
 obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o
-obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o pm-imx6q.o
+obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o
+
+ifeq ($(CONFIG_PM),y)
+obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o
+endif
diff --git a/arch/arm/mach-imx/head-v7.S b/arch/arm/mach-imx/head-v7.S
index 6229efbc70c..7e49deb128a 100644
--- a/arch/arm/mach-imx/head-v7.S
+++ b/arch/arm/mach-imx/head-v7.S
@@ -16,7 +16,6 @@
 #include <asm/hardware/cache-l2x0.h>
 
 	.section ".text.head", "ax"
-	__CPUINIT
 
 /*
  * The secondary kernel init calls v7_flush_dcache_all before it enables
@@ -33,6 +32,7 @@
  */
 ENTRY(v7_invalidate_l1)
 	mov	r0, #0
+	mcr	p15, 0, r0, c7, c5, 0	@ invalidate I cache
 	mcr	p15, 2, r0, c0, c0, 0
 	mrc	p15, 1, r0, c0, c0, 0
 
@@ -71,6 +71,7 @@ ENTRY(v7_secondary_startup)
 ENDPROC(v7_secondary_startup)
 #endif
 
+#ifdef CONFIG_PM
 /*
  * The following code is located into the .data section.  This is to
  * allow phys_l2x0_saved_regs to be accessed with a relative load
@@ -79,6 +80,7 @@ ENDPROC(v7_secondary_startup)
 	.data
 	.align
 
+#ifdef CONFIG_CACHE_L2X0
 	.macro	pl310_resume
 	ldr	r2, phys_l2x0_saved_regs
 	ldr	r0, [r2, #L2X0_R_PHY_BASE]	@ get physical base of l2x0
@@ -88,12 +90,17 @@ ENDPROC(v7_secondary_startup)
 	str	r1, [r0, #L2X0_CTRL]		@ re-enable L2
 	.endm
 
+	.globl	phys_l2x0_saved_regs
+phys_l2x0_saved_regs:
+        .long   0
+#else
+	.macro	pl310_resume
+	.endm
+#endif
+
 ENTRY(v7_cpu_resume)
 	bl	v7_invalidate_l1
 	pl310_resume
 	b	cpu_resume
 ENDPROC(v7_cpu_resume)
-
-	.globl	phys_l2x0_saved_regs
-phys_l2x0_saved_regs:
-        .long   0
+#endif
diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
index f20f191d7cc..f7b0c2b1b90 100644
--- a/arch/arm/mach-imx/pm-imx6q.c
+++ b/arch/arm/mach-imx/pm-imx6q.c
@@ -64,7 +64,9 @@ void __init imx6q_pm_init(void)
 	 * address of the data structure used by l2x0 core to save registers,
 	 * and later restore the necessary ones in imx6q resume entry.
 	 */
+#ifdef CONFIG_CACHE_L2X0
 	phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
+#endif
 
 	suspend_set_ops(&imx6q_pm_ops);
 }
diff --git a/arch/arm/mach-mx5/mm.c b/arch/arm/mach-mx5/mm.c
index df4a508f240..bc17dfea381 100644
--- a/arch/arm/mach-mx5/mm.c
+++ b/arch/arm/mach-mx5/mm.c
@@ -13,6 +13,7 @@
 
 #include <linux/mm.h>
 #include <linux/init.h>
+#include <linux/clk.h>
 
 #include <asm/mach/map.h>
 
@@ -21,10 +22,26 @@
 #include <mach/devices-common.h>
 #include <mach/iomux-v3.h>
 
+static struct clk *gpc_dvfs_clk;
+
 static void imx5_idle(void)
 {
-	if (!need_resched())
+	if (!need_resched()) {
+		/* gpc clock is needed for SRPG */
+		if (gpc_dvfs_clk == NULL) {
+			gpc_dvfs_clk = clk_get(NULL, "gpc_dvfs");
+			if (IS_ERR(gpc_dvfs_clk))
+				goto err0;
+		}
+		clk_enable(gpc_dvfs_clk);
 		mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF);
+		if (tzic_enable_wake())
+			goto err1;
+		cpu_do_idle();
+err1:
+		clk_disable(gpc_dvfs_clk);
+	}
+err0:
 	local_irq_enable();
 }
 
diff --git a/arch/arm/mach-mx5/system.c b/arch/arm/mach-mx5/system.c
index 144ebebc4a6..5eebfaad122 100644
--- a/arch/arm/mach-mx5/system.c
+++ b/arch/arm/mach-mx5/system.c
@@ -55,9 +55,6 @@ void mx5_cpu_lp_set(enum mxc_cpu_pwr_mode mode)
 			stop_mode = 1;
 		}
 		arm_srpgcr |= MXC_SRPGCR_PCR;
-
-		if (tzic_enable_wake(1) != 0)
-			return;
 		break;
 	case STOP_POWER_ON:
 		ccm_clpcr |= 0x2 << MXC_CCM_CLPCR_LPM_OFFSET;
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index b7407154c88..904bd1dfcd2 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -365,6 +365,27 @@ config OMAP3_SDRC_AC_TIMING
 	  wish to say no.  Selecting yes without understanding what is
 	  going on could result in system crashes;
 
+config OMAP4_ERRATA_I688
+	bool "OMAP4 errata: Async Bridge Corruption"
+	depends on ARCH_OMAP4
+	select ARCH_HAS_BARRIERS
+	help
+	  If a data is stalled inside asynchronous bridge because of back
+	  pressure, it may be accepted multiple times, creating pointer
+	  misalignment that will corrupt next transfers on that data path
+	  until next reset of the system (No recovery procedure once the
+	  issue is hit, the path remains consistently broken). Async bridge
+	  can be found on path between MPU to EMIF and MPU to L3 interconnect.
+	  This situation can happen only when the idle is initiated by a
+	  Master Request Disconnection (which is trigged by software when
+	  executing WFI on CPU).
+	  The work-around for this errata needs all the initiators connected
+	  through async bridge must ensure that data path is properly drained
+	  before issuing WFI. This condition will be met if one Strongly ordered
+	  access is performed to the target right before executing the WFI.
+	  In MPU case, L3 T2ASYNC FIFO and DDR T2ASYNC FIFO needs to be drained.
+	  IO barrier ensure that there is no synchronisation loss on initiators
+	  operating on both interconnect port simultaneously.
 endmenu
 
 endif
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 6d226a76d05..fc9b238cbc1 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -11,10 +11,11 @@ hwmod-common				= omap_hwmod.o \
 					  omap_hwmod_common_data.o
 clock-common				= clock.o clock_common_data.o \
 					  clkt_dpll.o clkt_clksel.o
+secure-common                          = omap-smc.o omap-secure.o
 
-obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common)
-obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common)
-obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common)
+obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common) $(secure-common)
+obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common) $(secure-common)
+obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common) $(secure-common)
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 
@@ -24,11 +25,13 @@ obj-$(CONFIG_TWL4030_CORE) += omap_twl.o
 obj-$(CONFIG_SMP)			+= omap-smp.o omap-headsmp.o
 obj-$(CONFIG_LOCAL_TIMERS)		+= timer-mpu.o
 obj-$(CONFIG_HOTPLUG_CPU)		+= omap-hotplug.o
-obj-$(CONFIG_ARCH_OMAP4)		+= omap44xx-smc.o omap4-common.o
+obj-$(CONFIG_ARCH_OMAP4)		+= omap4-common.o omap-wakeupgen.o \
+					   sleep44xx.o
 
 plus_sec := $(call as-instr,.arch_extension sec,+sec)
 AFLAGS_omap-headsmp.o			:=-Wa,-march=armv7-a$(plus_sec)
-AFLAGS_omap44xx-smc.o			:=-Wa,-march=armv7-a$(plus_sec)
+AFLAGS_omap-smc.o			:=-Wa,-march=armv7-a$(plus_sec)
+AFLAGS_sleep44xx.o			:=-Wa,-march=armv7-a$(plus_sec)
 
 # Functions loaded to SRAM
 obj-$(CONFIG_SOC_OMAP2420)		+= sram242x.o
@@ -62,7 +65,8 @@ obj-$(CONFIG_ARCH_OMAP2)		+= pm24xx.o
 obj-$(CONFIG_ARCH_OMAP2)		+= sleep24xx.o
 obj-$(CONFIG_ARCH_OMAP3)		+= pm34xx.o sleep34xx.o \
 					   cpuidle34xx.o
-obj-$(CONFIG_ARCH_OMAP4)		+= pm44xx.o
+obj-$(CONFIG_ARCH_OMAP4)		+= pm44xx.o omap-mpuss-lowpower.o \
+					   cpuidle44xx.o
 obj-$(CONFIG_PM_DEBUG)			+= pm-debug.o
 obj-$(CONFIG_OMAP_SMARTREFLEX)          += sr_device.o smartreflex.o
 obj-$(CONFIG_OMAP_SMARTREFLEX_CLASS3)	+= smartreflex-class3.o
@@ -77,6 +81,7 @@ endif
 endif
 
 # PRCM
+obj-y					+= prm_common.o
 obj-$(CONFIG_ARCH_OMAP2)		+= prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o
 obj-$(CONFIG_ARCH_OMAP3)		+= prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o \
 					   vc3xxx_data.o vp3xxx_data.o
@@ -86,7 +91,7 @@ obj-$(CONFIG_ARCH_OMAP3)		+= prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o \
 obj-$(CONFIG_ARCH_OMAP4)		+= prcm.o cm2xxx_3xxx.o cminst44xx.o \
 					   cm44xx.o prcm_mpu44xx.o \
 					   prminst44xx.o vc44xx_data.o \
-					   vp44xx_data.o
+					   vp44xx_data.o prm44xx.o
 
 # OMAP voltage domains
 voltagedomain-common			:= voltage.o vc.o vp.o
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 9996334cb68..383717ba63b 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -475,106 +475,8 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
 static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
-
-static struct omap_device_pad serial1_pads[] __initdata = {
-	/*
-	 * Note that off output enable is an active low
-	 * signal. So setting this means pin is a
-	 * input enabled in off mode
-	 */
-	OMAP_MUX_STATIC("uart1_cts.uart1_cts",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rts.uart1_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rx.uart1_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_tx.uart1_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLDOWN |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial1_data __initdata = {
-	.id		= 0,
-	.pads		= serial1_pads,
-	.pads_cnt	= ARRAY_SIZE(serial1_pads),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id		= 1,
-	.pads		= serial2_pads,
-	.pads_cnt	= ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id		= 2,
-	.pads		= serial3_pads,
-	.pads_cnt	= ARRAY_SIZE(serial3_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init_port(&serial1_data);
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
 #endif
 
 /*
@@ -711,7 +613,7 @@ static void __init omap_3430sdp_init(void)
 	else
 		gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
 	omap_ads7846_init(1, gpio_pendown, 310, NULL);
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(hyb18m512160af6_sdrc_params, NULL);
 	usb_musb_init(NULL);
 	board_smc91x_init();
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 4b4c9e25a83..2ceb75d21eb 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -844,74 +844,8 @@ static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial4_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart4_rx.uart4_rx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart4_tx.uart4_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id		= 1,
-	.pads		= serial2_pads,
-	.pads_cnt	= ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id		= 2,
-	.pads		= serial3_pads,
-	.pads_cnt	= ARRAY_SIZE(serial3_pads),
-};
-
-static struct omap_board_data serial4_data __initdata = {
-	.id		= 3,
-	.pads		= serial4_pads,
-	.pads_cnt	= ARRAY_SIZE(serial4_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	struct omap_board_data bdata;
-	bdata.flags	= 0;
-	bdata.pads	= NULL;
-	bdata.pads_cnt	= 0;
-	bdata.id	= 0;
-	/* pass dummy data for UART1 */
-	omap_serial_init_port(&bdata);
-
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-	omap_serial_init_port(&serial4_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
  #endif
 
 static void omap4_sdp4430_wifi_mux_init(void)
@@ -961,7 +895,7 @@ static void __init omap_4430sdp_init(void)
 	omap4_i2c_init();
 	omap_sfh7741prox_init();
 	platform_add_devices(sdp4430_devices, ARRAY_SIZE(sdp4430_devices));
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 	omap4_sdp4430_wifi_init();
 	omap4_twl6030_hsmmc_init(mmc);
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index f8c5b2cc7c9..d5875606048 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -69,7 +69,6 @@ static void __init omap_generic_init(void)
 	if (node)
 		irq_domain_add_simple(node, 0);
 
-	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 
 	of_platform_populate(NULL, omap_dt_match_table, NULL, NULL);
diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index 72d76ed94a6..42a4d11fad2 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -644,15 +644,15 @@ static inline void board_serial_init(void)
 	bdata.pads_cnt = 0;
 
 	bdata.id = 0;
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 
 	bdata.id = 1;
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 
 	bdata.id = 2;
 	bdata.pads = serial2_pads;
 	bdata.pads_cnt = ARRAY_SIZE(serial2_pads);
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 }
 
 #else
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 8b06c6a60d0..e96a2e7ad36 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -364,74 +364,8 @@ static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial4_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart4_rx.uart4_rx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart4_tx.uart4_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id             = 1,
-	.pads           = serial2_pads,
-	.pads_cnt       = ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id             = 2,
-	.pads           = serial3_pads,
-	.pads_cnt       = ARRAY_SIZE(serial3_pads),
-};
-
-static struct omap_board_data serial4_data __initdata = {
-	.id             = 3,
-	.pads           = serial4_pads,
-	.pads_cnt       = ARRAY_SIZE(serial4_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	struct omap_board_data bdata;
-	bdata.flags     = 0;
-	bdata.pads      = NULL;
-	bdata.pads_cnt  = 0;
-	bdata.id        = 0;
-	/* pass dummy data for UART1 */
-	omap_serial_init_port(&bdata);
-
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-	omap_serial_init_port(&serial4_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
 #endif
 
 /* Display DVI */
@@ -562,7 +496,7 @@ static void __init omap4_panda_init(void)
 	omap4_panda_i2c_init();
 	platform_add_devices(panda_devices, ARRAY_SIZE(panda_devices));
 	platform_device_register(&omap_vwlan_device);
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 	omap4_twl6030_hsmmc_init(mmc);
 	omap4_ehci_init();
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 9403b2ce6c8..febffde2ff1 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -24,9 +24,11 @@
 
 #ifndef __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H
 #define __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H
+#ifndef __ASSEMBLER__
 
 #include <linux/delay.h>
 #include <plat/common.h>
+#include <asm/proc-fns.h>
 
 #ifdef CONFIG_SOC_OMAP2420
 extern void omap242x_map_common_io(void);
@@ -168,23 +170,23 @@ void omap3_intc_resume_idle(void);
 void omap2_intc_handle_irq(struct pt_regs *regs);
 void omap3_intc_handle_irq(struct pt_regs *regs);
 
-/*
- * wfi used in low power code. Directly opcode is used instead
- * of instruction to avoid mulit-omap build break
- */
-#ifdef CONFIG_THUMB2_KERNEL
-#define do_wfi() __asm__ __volatile__ ("wfi" : : : "memory")
-#else
-#define do_wfi()			\
-		__asm__ __volatile__ (".word	0xe320f003" : : : "memory")
+#ifdef CONFIG_CACHE_L2X0
+extern void __iomem *omap4_get_l2cache_base(void);
 #endif
 
-#ifdef CONFIG_CACHE_L2X0
-extern void __iomem *l2cache_base;
+#ifdef CONFIG_SMP
+extern void __iomem *omap4_get_scu_base(void);
+#else
+static inline void __iomem *omap4_get_scu_base(void)
+{
+	return NULL;
+}
 #endif
 
 extern void __init gic_init_irq(void);
 extern void omap_smc1(u32 fn, u32 arg);
+extern void __iomem *omap4_get_sar_ram_base(void);
+extern void omap_do_wfi(void);
 
 #ifdef CONFIG_SMP
 /* Needed for secondary core boot */
@@ -194,4 +196,44 @@ extern void omap_auxcoreboot_addr(u32 cpu_addr);
 extern u32 omap_read_auxcoreboot0(void);
 #endif
 
+#if defined(CONFIG_SMP) && defined(CONFIG_PM)
+extern int omap4_mpuss_init(void);
+extern int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state);
+extern int omap4_finish_suspend(unsigned long cpu_state);
+extern void omap4_cpu_resume(void);
+extern int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state);
+extern u32 omap4_mpuss_read_prev_context_state(void);
+#else
+static inline int omap4_enter_lowpower(unsigned int cpu,
+					unsigned int power_state)
+{
+	cpu_do_idle();
+	return 0;
+}
+
+static inline int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
+{
+	cpu_do_idle();
+	return 0;
+}
+
+static inline int omap4_mpuss_init(void)
+{
+	return 0;
+}
+
+static inline int omap4_finish_suspend(unsigned long cpu_state)
+{
+	return 0;
+}
+
+static inline void omap4_cpu_resume(void)
+{}
+
+static inline u32 omap4_mpuss_read_prev_context_state(void)
+{
+	return 0;
+}
+#endif
+#endif /* __ASSEMBLER__ */
 #endif /* __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H */
diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c
index e20332f4abd..464cffde58f 100644
--- a/arch/arm/mach-omap2/cpuidle34xx.c
+++ b/arch/arm/mach-omap2/cpuidle34xx.c
@@ -25,12 +25,12 @@
 #include <linux/sched.h>
 #include <linux/cpuidle.h>
 #include <linux/export.h>
+#include <linux/cpu_pm.h>
 
 #include <plat/prcm.h>
 #include <plat/irqs.h>
 #include "powerdomain.h"
 #include "clockdomain.h"
-#include <plat/serial.h>
 
 #include "pm.h"
 #include "control.h"
@@ -124,9 +124,23 @@ static int omap3_enter_idle(struct cpuidle_device *dev,
 		pwrdm_for_each_clkdm(core_pd, _cpuidle_deny_idle);
 	}
 
+	/*
+	 * Call idle CPU PM enter notifier chain so that
+	 * VFP context is saved.
+	 */
+	if (mpu_state == PWRDM_POWER_OFF)
+		cpu_pm_enter();
+
 	/* Execute ARM wfi */
 	omap_sram_idle();
 
+	/*
+	 * Call idle CPU PM enter notifier chain to restore
+	 * VFP context.
+	 */
+	if (pwrdm_read_prev_pwrst(mpu_pd) == PWRDM_POWER_OFF)
+		cpu_pm_exit();
+
 	/* Re-allow idle for C1 */
 	if (index == 0) {
 		pwrdm_for_each_clkdm(mpu_pd, _cpuidle_allow_idle);
@@ -245,11 +259,6 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev,
 	struct omap3_idle_statedata *cx;
 	int ret;
 
-	if (!omap3_can_sleep()) {
-		new_state_idx = drv->safe_state_index;
-		goto select_state;
-	}
-
 	/*
 	 * Prevent idle completely if CAM is active.
 	 * CAM does not have wakeup capability in OMAP3.
diff --git a/arch/arm/mach-omap2/cpuidle44xx.c b/arch/arm/mach-omap2/cpuidle44xx.c
new file mode 100644
index 00000000000..cfdbb86bc84
--- /dev/null
+++ b/arch/arm/mach-omap2/cpuidle44xx.c
@@ -0,0 +1,245 @@
+/*
+ * OMAP4 CPU idle Routines
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * Santosh Shilimkar <santosh.shilimkar@ti.com>
+ * Rajendra Nayak <rnayak@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/sched.h>
+#include <linux/cpuidle.h>
+#include <linux/cpu_pm.h>
+#include <linux/export.h>
+#include <linux/clockchips.h>
+
+#include <asm/proc-fns.h>
+
+#include "common.h"
+#include "pm.h"
+#include "prm.h"
+
+#ifdef CONFIG_CPU_IDLE
+
+/* Machine specific information to be recorded in the C-state driver_data */
+struct omap4_idle_statedata {
+	u32 cpu_state;
+	u32 mpu_logic_state;
+	u32 mpu_state;
+	u8 valid;
+};
+
+static struct cpuidle_params cpuidle_params_table[] = {
+	/* C1 - CPU0 ON + CPU1 ON + MPU ON */
+	{.exit_latency = 2 + 2 , .target_residency = 5, .valid = 1},
+	/* C2- CPU0 OFF + CPU1 OFF + MPU CSWR */
+	{.exit_latency = 328 + 440 , .target_residency = 960, .valid = 1},
+	/* C3 - CPU0 OFF + CPU1 OFF + MPU OSWR */
+	{.exit_latency = 460 + 518 , .target_residency = 1100, .valid = 1},
+};
+
+#define OMAP4_NUM_STATES ARRAY_SIZE(cpuidle_params_table)
+
+struct omap4_idle_statedata omap4_idle_data[OMAP4_NUM_STATES];
+static struct powerdomain *mpu_pd, *cpu0_pd, *cpu1_pd;
+
+/**
+ * omap4_enter_idle - Programs OMAP4 to enter the specified state
+ * @dev: cpuidle device
+ * @drv: cpuidle driver
+ * @index: the index of state to be entered
+ *
+ * Called from the CPUidle framework to program the device to the
+ * specified low power state selected by the governor.
+ * Returns the amount of time spent in the low power state.
+ */
+static int omap4_enter_idle(struct cpuidle_device *dev,
+			struct cpuidle_driver *drv,
+			int index)
+{
+	struct omap4_idle_statedata *cx =
+			cpuidle_get_statedata(&dev->states_usage[index]);
+	struct timespec ts_preidle, ts_postidle, ts_idle;
+	u32 cpu1_state;
+	int idle_time;
+	int new_state_idx;
+	int cpu_id = smp_processor_id();
+
+	/* Used to keep track of the total time in idle */
+	getnstimeofday(&ts_preidle);
+
+	local_irq_disable();
+	local_fiq_disable();
+
+	/*
+	 * CPU0 has to stay ON (i.e in C1) until CPU1 is OFF state.
+	 * This is necessary to honour hardware recommondation
+	 * of triggeing all the possible low power modes once CPU1 is
+	 * out of coherency and in OFF mode.
+	 * Update dev->last_state so that governor stats reflects right
+	 * data.
+	 */
+	cpu1_state = pwrdm_read_pwrst(cpu1_pd);
+	if (cpu1_state != PWRDM_POWER_OFF) {
+		new_state_idx = drv->safe_state_index;
+		cx = cpuidle_get_statedata(&dev->states_usage[new_state_idx]);
+	}
+
+	if (index > 0)
+		clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu_id);
+
+	/*
+	 * Call idle CPU PM enter notifier chain so that
+	 * VFP and per CPU interrupt context is saved.
+	 */
+	if (cx->cpu_state == PWRDM_POWER_OFF)
+		cpu_pm_enter();
+
+	pwrdm_set_logic_retst(mpu_pd, cx->mpu_logic_state);
+	omap_set_pwrdm_state(mpu_pd, cx->mpu_state);
+
+	/*
+	 * Call idle CPU cluster PM enter notifier chain
+	 * to save GIC and wakeupgen context.
+	 */
+	if ((cx->mpu_state == PWRDM_POWER_RET) &&
+		(cx->mpu_logic_state == PWRDM_POWER_OFF))
+			cpu_cluster_pm_enter();
+
+	omap4_enter_lowpower(dev->cpu, cx->cpu_state);
+
+	/*
+	 * Call idle CPU PM exit notifier chain to restore
+	 * VFP and per CPU IRQ context. Only CPU0 state is
+	 * considered since CPU1 is managed by CPU hotplug.
+	 */
+	if (pwrdm_read_prev_pwrst(cpu0_pd) == PWRDM_POWER_OFF)
+		cpu_pm_exit();
+
+	/*
+	 * Call idle CPU cluster PM exit notifier chain
+	 * to restore GIC and wakeupgen context.
+	 */
+	if (omap4_mpuss_read_prev_context_state())
+		cpu_cluster_pm_exit();
+
+	if (index > 0)
+		clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu_id);
+
+	getnstimeofday(&ts_postidle);
+	ts_idle = timespec_sub(ts_postidle, ts_preidle);
+
+	local_irq_enable();
+	local_fiq_enable();
+
+	idle_time = ts_idle.tv_nsec / NSEC_PER_USEC + ts_idle.tv_sec * \
+								USEC_PER_SEC;
+
+	/* Update cpuidle counters */
+	dev->last_residency = idle_time;
+
+	return index;
+}
+
+DEFINE_PER_CPU(struct cpuidle_device, omap4_idle_dev);
+
+struct cpuidle_driver omap4_idle_driver = {
+	.name =		"omap4_idle",
+	.owner =	THIS_MODULE,
+};
+
+static inline void _fill_cstate(struct cpuidle_driver *drv,
+					int idx, const char *descr)
+{
+	struct cpuidle_state *state = &drv->states[idx];
+
+	state->exit_latency	= cpuidle_params_table[idx].exit_latency;
+	state->target_residency	= cpuidle_params_table[idx].target_residency;
+	state->flags		= CPUIDLE_FLAG_TIME_VALID;
+	state->enter		= omap4_enter_idle;
+	sprintf(state->name, "C%d", idx + 1);
+	strncpy(state->desc, descr, CPUIDLE_DESC_LEN);
+}
+
+static inline struct omap4_idle_statedata *_fill_cstate_usage(
+					struct cpuidle_device *dev,
+					int idx)
+{
+	struct omap4_idle_statedata *cx = &omap4_idle_data[idx];
+	struct cpuidle_state_usage *state_usage = &dev->states_usage[idx];
+
+	cx->valid		= cpuidle_params_table[idx].valid;
+	cpuidle_set_statedata(state_usage, cx);
+
+	return cx;
+}
+
+
+
+/**
+ * omap4_idle_init - Init routine for OMAP4 idle
+ *
+ * Registers the OMAP4 specific cpuidle driver to the cpuidle
+ * framework with the valid set of states.
+ */
+int __init omap4_idle_init(void)
+{
+	struct omap4_idle_statedata *cx;
+	struct cpuidle_device *dev;
+	struct cpuidle_driver *drv = &omap4_idle_driver;
+	unsigned int cpu_id = 0;
+
+	mpu_pd = pwrdm_lookup("mpu_pwrdm");
+	cpu0_pd = pwrdm_lookup("cpu0_pwrdm");
+	cpu1_pd = pwrdm_lookup("cpu1_pwrdm");
+	if ((!mpu_pd) || (!cpu0_pd) || (!cpu1_pd))
+		return -ENODEV;
+
+
+	drv->safe_state_index = -1;
+	dev = &per_cpu(omap4_idle_dev, cpu_id);
+	dev->cpu = cpu_id;
+
+	/* C1 - CPU0 ON + CPU1 ON + MPU ON */
+	_fill_cstate(drv, 0, "MPUSS ON");
+	drv->safe_state_index = 0;
+	cx = _fill_cstate_usage(dev, 0);
+	cx->valid = 1;	/* C1 is always valid */
+	cx->cpu_state = PWRDM_POWER_ON;
+	cx->mpu_state = PWRDM_POWER_ON;
+	cx->mpu_logic_state = PWRDM_POWER_RET;
+
+	/* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */
+	_fill_cstate(drv, 1, "MPUSS CSWR");
+	cx = _fill_cstate_usage(dev, 1);
+	cx->cpu_state = PWRDM_POWER_OFF;
+	cx->mpu_state = PWRDM_POWER_RET;
+	cx->mpu_logic_state = PWRDM_POWER_RET;
+
+	/* C3 - CPU0 OFF + CPU1 OFF + MPU OSWR */
+	_fill_cstate(drv, 2, "MPUSS OSWR");
+	cx = _fill_cstate_usage(dev, 2);
+	cx->cpu_state = PWRDM_POWER_OFF;
+	cx->mpu_state = PWRDM_POWER_RET;
+	cx->mpu_logic_state = PWRDM_POWER_OFF;
+
+	drv->state_count = OMAP4_NUM_STATES;
+	cpuidle_register_driver(&omap4_idle_driver);
+
+	dev->state_count = OMAP4_NUM_STATES;
+	if (cpuidle_register_device(dev)) {
+		pr_err("%s: CPUidle register device failed\n", __func__);
+			return -EIO;
+		}
+
+	return 0;
+}
+#else
+int __init omap4_idle_init(void)
+{
+	return 0;
+}
+#endif /* CONFIG_CPU_IDLE */
diff --git a/arch/arm/mach-omap2/include/mach/barriers.h b/arch/arm/mach-omap2/include/mach/barriers.h
new file mode 100644
index 00000000000..4fa72c7cc7c
--- /dev/null
+++ b/arch/arm/mach-omap2/include/mach/barriers.h
@@ -0,0 +1,31 @@
+/*
+ * OMAP memory barrier header.
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ *  Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *  Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __MACH_BARRIERS_H
+#define __MACH_BARRIERS_H
+
+extern void omap_bus_sync(void);
+
+#define rmb()		dsb()
+#define wmb()		do { dsb(); outer_sync(); omap_bus_sync(); } while (0)
+#define mb()		wmb()
+
+#endif	/* __MACH_BARRIERS_H */
diff --git a/arch/arm/mach-omap2/include/mach/omap-secure.h b/arch/arm/mach-omap2/include/mach/omap-secure.h
new file mode 100644
index 00000000000..c90a43589ab
--- /dev/null
+++ b/arch/arm/mach-omap2/include/mach/omap-secure.h
@@ -0,0 +1,57 @@
+/*
+ * omap-secure.h: OMAP Secure infrastructure header.
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef OMAP_ARCH_OMAP_SECURE_H
+#define OMAP_ARCH_OMAP_SECURE_H
+
+/* Monitor error code */
+#define  API_HAL_RET_VALUE_NS2S_CONVERSION_ERROR	0xFFFFFFFE
+#define  API_HAL_RET_VALUE_SERVICE_UNKNWON		0xFFFFFFFF
+
+/* HAL API error codes */
+#define  API_HAL_RET_VALUE_OK		0x00
+#define  API_HAL_RET_VALUE_FAIL		0x01
+
+/* Secure HAL API flags */
+#define FLAG_START_CRITICAL		0x4
+#define FLAG_IRQFIQ_MASK		0x3
+#define FLAG_IRQ_ENABLE			0x2
+#define FLAG_FIQ_ENABLE			0x1
+#define NO_FLAG				0x0
+
+/* Maximum Secure memory storage size */
+#define OMAP_SECURE_RAM_STORAGE	(88 * SZ_1K)
+
+/* Secure low power HAL API index */
+#define OMAP4_HAL_SAVESECURERAM_INDEX	0x1a
+#define OMAP4_HAL_SAVEHW_INDEX		0x1b
+#define OMAP4_HAL_SAVEALL_INDEX		0x1c
+#define OMAP4_HAL_SAVEGIC_INDEX		0x1d
+
+/* Secure Monitor mode APIs */
+#define OMAP4_MON_SCU_PWR_INDEX		0x108
+#define OMAP4_MON_L2X0_DBG_CTRL_INDEX	0x100
+#define OMAP4_MON_L2X0_CTRL_INDEX	0x102
+#define OMAP4_MON_L2X0_AUXCTRL_INDEX	0x109
+#define OMAP4_MON_L2X0_PREFETCH_INDEX	0x113
+
+/* Secure PPA(Primary Protected Application) APIs */
+#define OMAP4_PPA_L2_POR_INDEX		0x23
+#define OMAP4_PPA_CPU_ACTRL_SMP_INDEX	0x25
+
+#ifndef __ASSEMBLER__
+
+extern u32 omap_secure_dispatcher(u32 idx, u32 flag, u32 nargs,
+				u32 arg1, u32 arg2, u32 arg3, u32 arg4);
+extern u32 omap_smc2(u32 id, u32 falg, u32 pargs);
+extern phys_addr_t omap_secure_ram_mempool_base(void);
+
+#endif /* __ASSEMBLER__ */
+#endif /* OMAP_ARCH_OMAP_SECURE_H */
diff --git a/arch/arm/mach-omap2/include/mach/omap-wakeupgen.h b/arch/arm/mach-omap2/include/mach/omap-wakeupgen.h
new file mode 100644
index 00000000000..d79321b0f2a
--- /dev/null
+++ b/arch/arm/mach-omap2/include/mach/omap-wakeupgen.h
@@ -0,0 +1,39 @@
+/*
+ * OMAP WakeupGen header file
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef OMAP_ARCH_WAKEUPGEN_H
+#define OMAP_ARCH_WAKEUPGEN_H
+
+#define OMAP_WKG_CONTROL_0			0x00
+#define OMAP_WKG_ENB_A_0			0x10
+#define OMAP_WKG_ENB_B_0			0x14
+#define OMAP_WKG_ENB_C_0			0x18
+#define OMAP_WKG_ENB_D_0			0x1c
+#define OMAP_WKG_ENB_SECURE_A_0			0x20
+#define OMAP_WKG_ENB_SECURE_B_0			0x24
+#define OMAP_WKG_ENB_SECURE_C_0			0x28
+#define OMAP_WKG_ENB_SECURE_D_0			0x2c
+#define OMAP_WKG_ENB_A_1			0x410
+#define OMAP_WKG_ENB_B_1			0x414
+#define OMAP_WKG_ENB_C_1			0x418
+#define OMAP_WKG_ENB_D_1			0x41c
+#define OMAP_WKG_ENB_SECURE_A_1			0x420
+#define OMAP_WKG_ENB_SECURE_B_1			0x424
+#define OMAP_WKG_ENB_SECURE_C_1			0x428
+#define OMAP_WKG_ENB_SECURE_D_1			0x42c
+#define OMAP_AUX_CORE_BOOT_0			0x800
+#define OMAP_AUX_CORE_BOOT_1			0x804
+#define OMAP_PTMSYNCREQ_MASK			0xc00
+#define OMAP_PTMSYNCREQ_EN			0xc04
+#define OMAP_TIMESTAMPCYCLELO			0xc08
+#define OMAP_TIMESTAMPCYCLEHI			0xc0c
+
+extern int __init omap_wakeupgen_init(void);
+#endif
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 73d617f0dc4..3f174d51f67 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -254,6 +254,15 @@ static struct map_desc omap44xx_io_desc[] __initdata = {
 		.length		= L4_EMU_44XX_SIZE,
 		.type		= MT_DEVICE,
 	},
+#ifdef CONFIG_OMAP4_ERRATA_I688
+	{
+		.virtual	= OMAP4_SRAM_VA,
+		.pfn		= __phys_to_pfn(OMAP4_SRAM_PA),
+		.length		= PAGE_SIZE,
+		.type		= MT_MEMORY_SO,
+	},
+#endif
+
 };
 #endif
 
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 655e9480eb9..e1cc75d1a57 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -32,6 +32,8 @@
 #include <linux/debugfs.h>
 #include <linux/seq_file.h>
 #include <linux/uaccess.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
 
 #include <asm/system.h>
 
@@ -39,6 +41,7 @@
 
 #include "control.h"
 #include "mux.h"
+#include "prm.h"
 
 #define OMAP_MUX_BASE_OFFSET		0x30	/* Offset from CTRL_BASE */
 #define OMAP_MUX_BASE_SZ		0x5ca
@@ -306,7 +309,8 @@ omap_hwmod_mux_init(struct omap_device_pad *bpads, int nr_pads)
 		pad->idle = bpad->idle;
 		pad->off = bpad->off;
 
-		if (pad->flags & OMAP_DEVICE_PAD_REMUX)
+		if (pad->flags &
+		    (OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP))
 			nr_pads_dynamic++;
 
 		pr_debug("%s: Initialized %s\n", __func__, pad->name);
@@ -331,7 +335,8 @@ omap_hwmod_mux_init(struct omap_device_pad *bpads, int nr_pads)
 	for (i = 0; i < hmux->nr_pads; i++) {
 		struct omap_device_pad *pad = &hmux->pads[i];
 
-		if (pad->flags & OMAP_DEVICE_PAD_REMUX) {
+		if (pad->flags &
+		    (OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP)) {
 			pr_debug("%s: pad %s tagged dynamic\n",
 					__func__, pad->name);
 			hmux->pads_dynamic[nr_pads_dynamic] = pad;
@@ -351,6 +356,78 @@ err1:
 	return NULL;
 }
 
+/**
+ * omap_hwmod_mux_scan_wakeups - omap hwmod scan wakeup pads
+ * @hmux: Pads for a hwmod
+ * @mpu_irqs: MPU irq array for a hwmod
+ *
+ * Scans the wakeup status of pads for a single hwmod.  If an irq
+ * array is defined for this mux, the parser will call the registered
+ * ISRs for corresponding pads, otherwise the parser will stop at the
+ * first wakeup active pad and return.  Returns true if there is a
+ * pending and non-served wakeup event for the mux, otherwise false.
+ */
+static bool omap_hwmod_mux_scan_wakeups(struct omap_hwmod_mux_info *hmux,
+		struct omap_hwmod_irq_info *mpu_irqs)
+{
+	int i, irq;
+	unsigned int val;
+	u32 handled_irqs = 0;
+
+	for (i = 0; i < hmux->nr_pads_dynamic; i++) {
+		struct omap_device_pad *pad = hmux->pads_dynamic[i];
+
+		if (!(pad->flags & OMAP_DEVICE_PAD_WAKEUP) ||
+		    !(pad->idle & OMAP_WAKEUP_EN))
+			continue;
+
+		val = omap_mux_read(pad->partition, pad->mux->reg_offset);
+		if (!(val & OMAP_WAKEUP_EVENT))
+			continue;
+
+		if (!hmux->irqs)
+			return true;
+
+		irq = hmux->irqs[i];
+		/* make sure we only handle each irq once */
+		if (handled_irqs & 1 << irq)
+			continue;
+
+		handled_irqs |= 1 << irq;
+
+		generic_handle_irq(mpu_irqs[irq].irq);
+	}
+
+	return false;
+}
+
+/**
+ * _omap_hwmod_mux_handle_irq - Process wakeup events for a single hwmod
+ *
+ * Checks a single hwmod for every wakeup capable pad to see if there is an
+ * active wakeup event. If this is the case, call the corresponding ISR.
+ */
+static int _omap_hwmod_mux_handle_irq(struct omap_hwmod *oh, void *data)
+{
+	if (!oh->mux || !oh->mux->enabled)
+		return 0;
+	if (omap_hwmod_mux_scan_wakeups(oh->mux, oh->mpu_irqs))
+		generic_handle_irq(oh->mpu_irqs[0].irq);
+	return 0;
+}
+
+/**
+ * omap_hwmod_mux_handle_irq - Process pad wakeup irqs.
+ *
+ * Calls a function for each registered omap_hwmod to check
+ * pad wakeup statuses.
+ */
+static irqreturn_t omap_hwmod_mux_handle_irq(int irq, void *unused)
+{
+	omap_hwmod_for_each(_omap_hwmod_mux_handle_irq, NULL);
+	return IRQ_HANDLED;
+}
+
 /* Assumes the calling function takes care of locking */
 void omap_hwmod_mux(struct omap_hwmod_mux_info *hmux, u8 state)
 {
@@ -715,6 +792,7 @@ static void __init omap_mux_free_names(struct omap_mux *m)
 static int __init omap_mux_late_init(void)
 {
 	struct omap_mux_partition *partition;
+	int ret;
 
 	list_for_each_entry(partition, &mux_partitions, node) {
 		struct omap_mux_entry *e, *tmp;
@@ -735,6 +813,13 @@ static int __init omap_mux_late_init(void)
 		}
 	}
 
+	ret = request_irq(omap_prcm_event_to_irq("io"),
+		omap_hwmod_mux_handle_irq, IRQF_SHARED | IRQF_NO_SUSPEND,
+			"hwmod_io", omap_mux_late_init);
+
+	if (ret)
+		pr_warning("mux: Failed to setup hwmod io irq %d\n", ret);
+
 	omap_mux_dbg_init();
 
 	return 0;
diff --git a/arch/arm/mach-omap2/omap-headsmp.S b/arch/arm/mach-omap2/omap-headsmp.S
index 4ee6aeca885..b13ef7ef5ef 100644
--- a/arch/arm/mach-omap2/omap-headsmp.S
+++ b/arch/arm/mach-omap2/omap-headsmp.S
@@ -18,11 +18,6 @@
 #include <linux/linkage.h>
 #include <linux/init.h>
 
-/* Physical address needed since MMU not enabled yet on secondary core */
-#define OMAP4_AUX_CORE_BOOT1_PA			0x48281804
-
-	__INIT
-
 /*
  * OMAP4 specific entry point for secondary CPU to jump from ROM
  * code.  This routine also provides a holding flag into which
diff --git a/arch/arm/mach-omap2/omap-hotplug.c b/arch/arm/mach-omap2/omap-hotplug.c
index e5a1c3f40a8..adbe4d8c7ca 100644
--- a/arch/arm/mach-omap2/omap-hotplug.c
+++ b/arch/arm/mach-omap2/omap-hotplug.c
@@ -22,6 +22,8 @@
 
 #include "common.h"
 
+#include "powerdomain.h"
+
 int platform_cpu_kill(unsigned int cpu)
 {
 	return 1;
@@ -33,6 +35,8 @@ int platform_cpu_kill(unsigned int cpu)
  */
 void platform_cpu_die(unsigned int cpu)
 {
+	unsigned int this_cpu;
+
 	flush_cache_all();
 	dsb();
 
@@ -40,15 +44,15 @@ void platform_cpu_die(unsigned int cpu)
 	 * we're ready for shutdown now, so do it
 	 */
 	if (omap_modify_auxcoreboot0(0x0, 0x200) != 0x0)
-		printk(KERN_CRIT "Secure clear status failed\n");
+		pr_err("Secure clear status failed\n");
 
 	for (;;) {
 		/*
-		 * Execute WFI
+		 * Enter into low power state
 		 */
-		do_wfi();
-
-		if (omap_read_auxcoreboot0() == cpu) {
+		omap4_hotplug_cpu(cpu, PWRDM_POWER_OFF);
+		this_cpu = smp_processor_id();
+		if (omap_read_auxcoreboot0() == this_cpu) {
 			/*
 			 * OK, proper wakeup, we're done
 			 */
diff --git a/arch/arm/mach-omap2/omap-mpuss-lowpower.c b/arch/arm/mach-omap2/omap-mpuss-lowpower.c
new file mode 100644
index 00000000000..1d5d0105655
--- /dev/null
+++ b/arch/arm/mach-omap2/omap-mpuss-lowpower.c
@@ -0,0 +1,398 @@
+/*
+ * OMAP MPUSS low power code
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * OMAP4430 MPUSS mainly consists of dual Cortex-A9 with per-CPU
+ * Local timer and Watchdog, GIC, SCU, PL310 L2 cache controller,
+ * CPU0 and CPU1 LPRM modules.
+ * CPU0, CPU1 and MPUSS each have there own power domain and
+ * hence multiple low power combinations of MPUSS are possible.
+ *
+ * The CPU0 and CPU1 can't support Closed switch Retention (CSWR)
+ * because the mode is not supported by hw constraints of dormant
+ * mode. While waking up from the dormant mode, a reset  signal
+ * to the Cortex-A9 processor must be asserted by the external
+ * power controller.
+ *
+ * With architectural inputs and hardware recommendations, only
+ * below modes are supported from power gain vs latency point of view.
+ *
+ *	CPU0		CPU1		MPUSS
+ *	----------------------------------------------
+ *	ON		ON		ON
+ *	ON(Inactive)	OFF		ON(Inactive)
+ *	OFF		OFF		CSWR
+ *	OFF		OFF		OSWR
+ *	OFF		OFF		OFF(Device OFF *TBD)
+ *	----------------------------------------------
+ *
+ * Note: CPU0 is the master core and it is the last CPU to go down
+ * and first to wake-up when MPUSS low power states are excercised
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <linux/smp.h>
+
+#include <asm/cacheflush.h>
+#include <asm/tlbflush.h>
+#include <asm/smp_scu.h>
+#include <asm/system.h>
+#include <asm/pgalloc.h>
+#include <asm/suspend.h>
+#include <asm/hardware/cache-l2x0.h>
+
+#include <plat/omap44xx.h>
+
+#include "common.h"
+#include "omap4-sar-layout.h"
+#include "pm.h"
+#include "prcm_mpu44xx.h"
+#include "prminst44xx.h"
+#include "prcm44xx.h"
+#include "prm44xx.h"
+#include "prm-regbits-44xx.h"
+
+#ifdef CONFIG_SMP
+
+struct omap4_cpu_pm_info {
+	struct powerdomain *pwrdm;
+	void __iomem *scu_sar_addr;
+	void __iomem *wkup_sar_addr;
+	void __iomem *l2x0_sar_addr;
+};
+
+static DEFINE_PER_CPU(struct omap4_cpu_pm_info, omap4_pm_info);
+static struct powerdomain *mpuss_pd;
+static void __iomem *sar_base;
+
+/*
+ * Program the wakeup routine address for the CPU0 and CPU1
+ * used for OFF or DORMANT wakeup.
+ */
+static inline void set_cpu_wakeup_addr(unsigned int cpu_id, u32 addr)
+{
+	struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
+
+	__raw_writel(addr, pm_info->wkup_sar_addr);
+}
+
+/*
+ * Set the CPUx powerdomain's previous power state
+ */
+static inline void set_cpu_next_pwrst(unsigned int cpu_id,
+				unsigned int power_state)
+{
+	struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
+
+	pwrdm_set_next_pwrst(pm_info->pwrdm, power_state);
+}
+
+/*
+ * Read CPU's previous power state
+ */
+static inline unsigned int read_cpu_prev_pwrst(unsigned int cpu_id)
+{
+	struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
+
+	return pwrdm_read_prev_pwrst(pm_info->pwrdm);
+}
+
+/*
+ * Clear the CPUx powerdomain's previous power state
+ */
+static inline void clear_cpu_prev_pwrst(unsigned int cpu_id)
+{
+	struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
+
+	pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
+}
+
+/*
+ * Store the SCU power status value to scratchpad memory
+ */
+static void scu_pwrst_prepare(unsigned int cpu_id, unsigned int cpu_state)
+{
+	struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
+	u32 scu_pwr_st;
+
+	switch (cpu_state) {
+	case PWRDM_POWER_RET:
+		scu_pwr_st = SCU_PM_DORMANT;
+		break;
+	case PWRDM_POWER_OFF:
+		scu_pwr_st = SCU_PM_POWEROFF;
+		break;
+	case PWRDM_POWER_ON:
+	case PWRDM_POWER_INACTIVE:
+	default:
+		scu_pwr_st = SCU_PM_NORMAL;
+		break;
+	}
+
+	__raw_writel(scu_pwr_st, pm_info->scu_sar_addr);
+}
+
+/* Helper functions for MPUSS OSWR */
+static inline void mpuss_clear_prev_logic_pwrst(void)
+{
+	u32 reg;
+
+	reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION,
+		OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
+	omap4_prminst_write_inst_reg(reg, OMAP4430_PRM_PARTITION,
+		OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
+}
+
+static inline void cpu_clear_prev_logic_pwrst(unsigned int cpu_id)
+{
+	u32 reg;
+
+	if (cpu_id) {
+		reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU1_INST,
+					OMAP4_RM_CPU1_CPU1_CONTEXT_OFFSET);
+		omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU1_INST,
+					OMAP4_RM_CPU1_CPU1_CONTEXT_OFFSET);
+	} else {
+		reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU0_INST,
+					OMAP4_RM_CPU0_CPU0_CONTEXT_OFFSET);
+		omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU0_INST,
+					OMAP4_RM_CPU0_CPU0_CONTEXT_OFFSET);
+	}
+}
+
+/**
+ * omap4_mpuss_read_prev_context_state:
+ * Function returns the MPUSS previous context state
+ */
+u32 omap4_mpuss_read_prev_context_state(void)
+{
+	u32 reg;
+
+	reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION,
+		OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
+	reg &= OMAP4430_LOSTCONTEXT_DFF_MASK;
+	return reg;
+}
+
+/*
+ * Store the CPU cluster state for L2X0 low power operations.
+ */
+static void l2x0_pwrst_prepare(unsigned int cpu_id, unsigned int save_state)
+{
+	struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
+
+	__raw_writel(save_state, pm_info->l2x0_sar_addr);
+}
+
+/*
+ * Save the L2X0 AUXCTRL and POR value to SAR memory. Its used to
+ * in every restore MPUSS OFF path.
+ */
+#ifdef CONFIG_CACHE_L2X0
+static void save_l2x0_context(void)
+{
+	u32 val;
+	void __iomem *l2x0_base = omap4_get_l2cache_base();
+
+	val = __raw_readl(l2x0_base + L2X0_AUX_CTRL);
+	__raw_writel(val, sar_base + L2X0_AUXCTRL_OFFSET);
+	val = __raw_readl(l2x0_base + L2X0_PREFETCH_CTRL);
+	__raw_writel(val, sar_base + L2X0_PREFETCH_CTRL_OFFSET);
+}
+#else
+static void save_l2x0_context(void)
+{}
+#endif
+
+/**
+ * omap4_enter_lowpower: OMAP4 MPUSS Low Power Entry Function
+ * The purpose of this function is to manage low power programming
+ * of OMAP4 MPUSS subsystem
+ * @cpu : CPU ID
+ * @power_state: Low power state.
+ *
+ * MPUSS states for the context save:
+ * save_state =
+ *	0 - Nothing lost and no need to save: MPUSS INACTIVE
+ *	1 - CPUx L1 and logic lost: MPUSS CSWR
+ *	2 - CPUx L1 and logic lost + GIC lost: MPUSS OSWR
+ *	3 - CPUx L1 and logic lost + GIC + L2 lost: DEVICE OFF
+ */
+int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
+{
+	unsigned int save_state = 0;
+	unsigned int wakeup_cpu;
+
+	if (omap_rev() == OMAP4430_REV_ES1_0)
+		return -ENXIO;
+
+	switch (power_state) {
+	case PWRDM_POWER_ON:
+	case PWRDM_POWER_INACTIVE:
+		save_state = 0;
+		break;
+	case PWRDM_POWER_OFF:
+		save_state = 1;
+		break;
+	case PWRDM_POWER_RET:
+	default:
+		/*
+		 * CPUx CSWR is invalid hardware state. Also CPUx OSWR
+		 * doesn't make much scense, since logic is lost and $L1
+		 * needs to be cleaned because of coherency. This makes
+		 * CPUx OSWR equivalent to CPUX OFF and hence not supported
+		 */
+		WARN_ON(1);
+		return -ENXIO;
+	}
+
+	pwrdm_pre_transition();
+
+	/*
+	 * Check MPUSS next state and save interrupt controller if needed.
+	 * In MPUSS OSWR or device OFF, interrupt controller  contest is lost.
+	 */
+	mpuss_clear_prev_logic_pwrst();
+	pwrdm_clear_all_prev_pwrst(mpuss_pd);
+	if ((pwrdm_read_next_pwrst(mpuss_pd) == PWRDM_POWER_RET) &&
+		(pwrdm_read_logic_retst(mpuss_pd) == PWRDM_POWER_OFF))
+		save_state = 2;
+
+	clear_cpu_prev_pwrst(cpu);
+	cpu_clear_prev_logic_pwrst(cpu);
+	set_cpu_next_pwrst(cpu, power_state);
+	set_cpu_wakeup_addr(cpu, virt_to_phys(omap4_cpu_resume));
+	scu_pwrst_prepare(cpu, power_state);
+	l2x0_pwrst_prepare(cpu, save_state);
+
+	/*
+	 * Call low level function  with targeted low power state.
+	 */
+	cpu_suspend(save_state, omap4_finish_suspend);
+
+	/*
+	 * Restore the CPUx power state to ON otherwise CPUx
+	 * power domain can transitions to programmed low power
+	 * state while doing WFI outside the low powe code. On
+	 * secure devices, CPUx does WFI which can result in
+	 * domain transition
+	 */
+	wakeup_cpu = smp_processor_id();
+	set_cpu_next_pwrst(wakeup_cpu, PWRDM_POWER_ON);
+
+	pwrdm_post_transition();
+
+	return 0;
+}
+
+/**
+ * omap4_hotplug_cpu: OMAP4 CPU hotplug entry
+ * @cpu : CPU ID
+ * @power_state: CPU low power state.
+ */
+int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
+{
+	unsigned int cpu_state = 0;
+
+	if (omap_rev() == OMAP4430_REV_ES1_0)
+		return -ENXIO;
+
+	if (power_state == PWRDM_POWER_OFF)
+		cpu_state = 1;
+
+	clear_cpu_prev_pwrst(cpu);
+	set_cpu_next_pwrst(cpu, power_state);
+	set_cpu_wakeup_addr(cpu, virt_to_phys(omap_secondary_startup));
+	scu_pwrst_prepare(cpu, power_state);
+
+	/*
+	 * CPU never retuns back if targetted power state is OFF mode.
+	 * CPU ONLINE follows normal CPU ONLINE ptah via
+	 * omap_secondary_startup().
+	 */
+	omap4_finish_suspend(cpu_state);
+
+	set_cpu_next_pwrst(cpu, PWRDM_POWER_ON);
+	return 0;
+}
+
+
+/*
+ * Initialise OMAP4 MPUSS
+ */
+int __init omap4_mpuss_init(void)
+{
+	struct omap4_cpu_pm_info *pm_info;
+
+	if (omap_rev() == OMAP4430_REV_ES1_0) {
+		WARN(1, "Power Management not supported on OMAP4430 ES1.0\n");
+		return -ENODEV;
+	}
+
+	sar_base = omap4_get_sar_ram_base();
+
+	/* Initilaise per CPU PM information */
+	pm_info = &per_cpu(omap4_pm_info, 0x0);
+	pm_info->scu_sar_addr = sar_base + SCU_OFFSET0;
+	pm_info->wkup_sar_addr = sar_base + CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
+	pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET0;
+	pm_info->pwrdm = pwrdm_lookup("cpu0_pwrdm");
+	if (!pm_info->pwrdm) {
+		pr_err("Lookup failed for CPU0 pwrdm\n");
+		return -ENODEV;
+	}
+
+	/* Clear CPU previous power domain state */
+	pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
+	cpu_clear_prev_logic_pwrst(0);
+
+	/* Initialise CPU0 power domain state to ON */
+	pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
+
+	pm_info = &per_cpu(omap4_pm_info, 0x1);
+	pm_info->scu_sar_addr = sar_base + SCU_OFFSET1;
+	pm_info->wkup_sar_addr = sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
+	pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET1;
+	pm_info->pwrdm = pwrdm_lookup("cpu1_pwrdm");
+	if (!pm_info->pwrdm) {
+		pr_err("Lookup failed for CPU1 pwrdm\n");
+		return -ENODEV;
+	}
+
+	/* Clear CPU previous power domain state */
+	pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
+	cpu_clear_prev_logic_pwrst(1);
+
+	/* Initialise CPU1 power domain state to ON */
+	pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
+
+	mpuss_pd = pwrdm_lookup("mpu_pwrdm");
+	if (!mpuss_pd) {
+		pr_err("Failed to lookup MPUSS power domain\n");
+		return -ENODEV;
+	}
+	pwrdm_clear_all_prev_pwrst(mpuss_pd);
+	mpuss_clear_prev_logic_pwrst();
+
+	/* Save device type on scratchpad for low level code to use */
+	if (omap_type() != OMAP2_DEVICE_TYPE_GP)
+		__raw_writel(1, sar_base + OMAP_TYPE_OFFSET);
+	else
+		__raw_writel(0, sar_base + OMAP_TYPE_OFFSET);
+
+	save_l2x0_context();
+
+	return 0;
+}
+
+#endif
diff --git a/arch/arm/mach-omap2/omap-secure.c b/arch/arm/mach-omap2/omap-secure.c
new file mode 100644
index 00000000000..69f3c72d959
--- /dev/null
+++ b/arch/arm/mach-omap2/omap-secure.c
@@ -0,0 +1,81 @@
+/*
+ * OMAP Secure API infrastructure.
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ *
+ * This program is free software,you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/memblock.h>
+
+#include <asm/cacheflush.h>
+
+#include <mach/omap-secure.h>
+
+static phys_addr_t omap_secure_memblock_base;
+
+/**
+ * omap_sec_dispatcher: Routine to dispatch low power secure
+ * service routines
+ * @idx: The HAL API index
+ * @flag: The flag indicating criticality of operation
+ * @nargs: Number of valid arguments out of four.
+ * @arg1, arg2, arg3 args4: Parameters passed to secure API
+ *
+ * Return the non-zero error value on failure.
+ */
+u32 omap_secure_dispatcher(u32 idx, u32 flag, u32 nargs, u32 arg1, u32 arg2,
+							 u32 arg3, u32 arg4)
+{
+	u32 ret;
+	u32 param[5];
+
+	param[0] = nargs;
+	param[1] = arg1;
+	param[2] = arg2;
+	param[3] = arg3;
+	param[4] = arg4;
+
+	/*
+	 * Secure API needs physical address
+	 * pointer for the parameters
+	 */
+	flush_cache_all();
+	outer_clean_range(__pa(param), __pa(param + 5));
+	ret = omap_smc2(idx, flag, __pa(param));
+
+	return ret;
+}
+
+/* Allocate the memory to save secure ram */
+int __init omap_secure_ram_reserve_memblock(void)
+{
+	phys_addr_t paddr;
+	u32 size = OMAP_SECURE_RAM_STORAGE;
+
+	size = ALIGN(size, SZ_1M);
+	paddr = memblock_alloc(size, SZ_1M);
+	if (!paddr) {
+		pr_err("%s: failed to reserve %x bytes\n",
+				__func__, size);
+		return -ENOMEM;
+	}
+	memblock_free(paddr, size);
+	memblock_remove(paddr, size);
+
+	omap_secure_memblock_base = paddr;
+
+	return 0;
+}
+
+phys_addr_t omap_secure_ram_mempool_base(void)
+{
+	return omap_secure_memblock_base;
+}
diff --git a/arch/arm/mach-omap2/omap44xx-smc.S b/arch/arm/mach-omap2/omap-smc.S
index e69d37d9520..f6441c13cd8 100644
--- a/arch/arm/mach-omap2/omap44xx-smc.S
+++ b/arch/arm/mach-omap2/omap-smc.S
@@ -31,6 +31,29 @@ ENTRY(omap_smc1)
 	ldmfd   sp!, {r2-r12, pc}
 ENDPROC(omap_smc1)
 
+/**
+ * u32 omap_smc2(u32 id, u32 falg, u32 pargs)
+ * Low level common routine for secure HAL and PPA APIs.
+ * @id: Application ID of HAL APIs
+ * @flag: Flag to indicate the criticality of operation
+ * @pargs: Physical address of parameter list starting
+ *	    with number of parametrs
+ */
+ENTRY(omap_smc2)
+	stmfd   sp!, {r4-r12, lr}
+	mov	r3, r2
+	mov	r2, r1
+	mov	r1, #0x0	@ Process ID
+	mov	r6, #0xff
+	mov	r12, #0x00	@ Secure Service ID
+	mov	r7, #0
+	mcr	p15, 0, r7, c7, c5, 6
+	dsb
+	dmb
+	smc	#0
+	ldmfd   sp!, {r4-r12, pc}
+ENDPROC(omap_smc2)
+
 ENTRY(omap_modify_auxcoreboot0)
 	stmfd   sp!, {r1-r12, lr}
 	ldr	r12, =0x104
diff --git a/arch/arm/mach-omap2/omap-smp.c b/arch/arm/mach-omap2/omap-smp.c
index e99bc6cd471..c1bf3ef0ba0 100644
--- a/arch/arm/mach-omap2/omap-smp.c
+++ b/arch/arm/mach-omap2/omap-smp.c
@@ -24,17 +24,37 @@
 #include <asm/hardware/gic.h>
 #include <asm/smp_scu.h>
 #include <mach/hardware.h>
+#include <mach/omap-secure.h>
 
 #include "common.h"
 
+#include "clockdomain.h"
+
 /* SCU base address */
 static void __iomem *scu_base;
 
 static DEFINE_SPINLOCK(boot_lock);
 
+void __iomem *omap4_get_scu_base(void)
+{
+	return scu_base;
+}
+
 void __cpuinit platform_secondary_init(unsigned int cpu)
 {
 	/*
+	 * Configure ACTRL and enable NS SMP bit access on CPU1 on HS device.
+	 * OMAP44XX EMU/HS devices - CPU0 SMP bit access is enabled in PPA
+	 * init and for CPU1, a secure PPA API provided. CPU0 must be ON
+	 * while executing NS_SMP API on CPU1 and PPA version must be 1.4.0+.
+	 * OMAP443X GP devices- SMP bit isn't accessible.
+	 * OMAP446X GP devices - SMP bit access is enabled on both CPUs.
+	 */
+	if (cpu_is_omap443x() && (omap_type() != OMAP2_DEVICE_TYPE_GP))
+		omap_secure_dispatcher(OMAP4_PPA_CPU_ACTRL_SMP_INDEX,
+							4, 0, 0, 0, 0, 0);
+
+	/*
 	 * If any interrupts are already enabled for the primary
 	 * core (e.g. timer irq), then they will not have been enabled
 	 * for us: do so
@@ -50,6 +70,8 @@ void __cpuinit platform_secondary_init(unsigned int cpu)
 
 int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
+	static struct clockdomain *cpu1_clkdm;
+	static bool booted;
 	/*
 	 * Set synchronisation state between this boot processor
 	 * and the secondary one
@@ -65,6 +87,29 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
 	omap_modify_auxcoreboot0(0x200, 0xfffffdff);
 	flush_cache_all();
 	smp_wmb();
+
+	if (!cpu1_clkdm)
+		cpu1_clkdm = clkdm_lookup("mpu1_clkdm");
+
+	/*
+	 * The SGI(Software Generated Interrupts) are not wakeup capable
+	 * from low power states. This is known limitation on OMAP4 and
+	 * needs to be worked around by using software forced clockdomain
+	 * wake-up. To wakeup CPU1, CPU0 forces the CPU1 clockdomain to
+	 * software force wakeup. The clockdomain is then put back to
+	 * hardware supervised mode.
+	 * More details can be found in OMAP4430 TRM - Version J
+	 * Section :
+	 *	4.3.4.2 Power States of CPU0 and CPU1
+	 */
+	if (booted) {
+		clkdm_wakeup(cpu1_clkdm);
+		clkdm_allow_idle(cpu1_clkdm);
+	} else {
+		dsb_sev();
+		booted = true;
+	}
+
 	gic_raise_softirq(cpumask_of(cpu), 1);
 
 	/*
diff --git a/arch/arm/mach-omap2/omap-wakeupgen.c b/arch/arm/mach-omap2/omap-wakeupgen.c
new file mode 100644
index 00000000000..d3d8971d7f3
--- /dev/null
+++ b/arch/arm/mach-omap2/omap-wakeupgen.c
@@ -0,0 +1,389 @@
+/*
+ * OMAP WakeupGen Source file
+ *
+ * OMAP WakeupGen is the interrupt controller extension used along
+ * with ARM GIC to wake the CPU out from low power states on
+ * external interrupts. It is responsible for generating wakeup
+ * event from the incoming interrupts and enable bits. It is
+ * implemented in MPU always ON power domain. During normal operation,
+ * WakeupGen delivers external interrupts directly to the GIC.
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/cpu.h>
+#include <linux/notifier.h>
+#include <linux/cpu_pm.h>
+
+#include <asm/hardware/gic.h>
+
+#include <mach/omap-wakeupgen.h>
+#include <mach/omap-secure.h>
+
+#include "omap4-sar-layout.h"
+#include "common.h"
+
+#define NR_REG_BANKS		4
+#define MAX_IRQS		128
+#define WKG_MASK_ALL		0x00000000
+#define WKG_UNMASK_ALL		0xffffffff
+#define CPU_ENA_OFFSET		0x400
+#define CPU0_ID			0x0
+#define CPU1_ID			0x1
+
+static void __iomem *wakeupgen_base;
+static void __iomem *sar_base;
+static DEFINE_PER_CPU(u32 [NR_REG_BANKS], irqmasks);
+static DEFINE_SPINLOCK(wakeupgen_lock);
+static unsigned int irq_target_cpu[NR_IRQS];
+
+/*
+ * Static helper functions.
+ */
+static inline u32 wakeupgen_readl(u8 idx, u32 cpu)
+{
+	return __raw_readl(wakeupgen_base + OMAP_WKG_ENB_A_0 +
+				(cpu * CPU_ENA_OFFSET) + (idx * 4));
+}
+
+static inline void wakeupgen_writel(u32 val, u8 idx, u32 cpu)
+{
+	__raw_writel(val, wakeupgen_base + OMAP_WKG_ENB_A_0 +
+				(cpu * CPU_ENA_OFFSET) + (idx * 4));
+}
+
+static inline void sar_writel(u32 val, u32 offset, u8 idx)
+{
+	__raw_writel(val, sar_base + offset + (idx * 4));
+}
+
+static void _wakeupgen_set_all(unsigned int cpu, unsigned int reg)
+{
+	u8 i;
+
+	for (i = 0; i < NR_REG_BANKS; i++)
+		wakeupgen_writel(reg, i, cpu);
+}
+
+static inline int _wakeupgen_get_irq_info(u32 irq, u32 *bit_posn, u8 *reg_index)
+{
+	unsigned int spi_irq;
+
+	/*
+	 * PPIs and SGIs are not supported.
+	 */
+	if (irq < OMAP44XX_IRQ_GIC_START)
+		return -EINVAL;
+
+	/*
+	 * Subtract the GIC offset.
+	 */
+	spi_irq = irq - OMAP44XX_IRQ_GIC_START;
+	if (spi_irq > MAX_IRQS) {
+		pr_err("omap wakeupGen: Invalid IRQ%d\n", irq);
+		return -EINVAL;
+	}
+
+	/*
+	 * Each WakeupGen register controls 32 interrupt.
+	 * i.e. 1 bit per SPI IRQ
+	 */
+	*reg_index = spi_irq >> 5;
+	*bit_posn = spi_irq %= 32;
+
+	return 0;
+}
+
+static void _wakeupgen_clear(unsigned int irq, unsigned int cpu)
+{
+	u32 val, bit_number;
+	u8 i;
+
+	if (_wakeupgen_get_irq_info(irq, &bit_number, &i))
+		return;
+
+	val = wakeupgen_readl(i, cpu);
+	val &= ~BIT(bit_number);
+	wakeupgen_writel(val, i, cpu);
+}
+
+static void _wakeupgen_set(unsigned int irq, unsigned int cpu)
+{
+	u32 val, bit_number;
+	u8 i;
+
+	if (_wakeupgen_get_irq_info(irq, &bit_number, &i))
+		return;
+
+	val = wakeupgen_readl(i, cpu);
+	val |= BIT(bit_number);
+	wakeupgen_writel(val, i, cpu);
+}
+
+static void _wakeupgen_save_masks(unsigned int cpu)
+{
+	u8 i;
+
+	for (i = 0; i < NR_REG_BANKS; i++)
+		per_cpu(irqmasks, cpu)[i] = wakeupgen_readl(i, cpu);
+}
+
+static void _wakeupgen_restore_masks(unsigned int cpu)
+{
+	u8 i;
+
+	for (i = 0; i < NR_REG_BANKS; i++)
+		wakeupgen_writel(per_cpu(irqmasks, cpu)[i], i, cpu);
+}
+
+/*
+ * Architecture specific Mask extension
+ */
+static void wakeupgen_mask(struct irq_data *d)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&wakeupgen_lock, flags);
+	_wakeupgen_clear(d->irq, irq_target_cpu[d->irq]);
+	spin_unlock_irqrestore(&wakeupgen_lock, flags);
+}
+
+/*
+ * Architecture specific Unmask extension
+ */
+static void wakeupgen_unmask(struct irq_data *d)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&wakeupgen_lock, flags);
+	_wakeupgen_set(d->irq, irq_target_cpu[d->irq]);
+	spin_unlock_irqrestore(&wakeupgen_lock, flags);
+}
+
+/*
+ * Mask or unmask all interrupts on given CPU.
+ *	0 = Mask all interrupts on the 'cpu'
+ *	1 = Unmask all interrupts on the 'cpu'
+ * Ensure that the initial mask is maintained. This is faster than
+ * iterating through GIC registers to arrive at the correct masks.
+ */
+static void wakeupgen_irqmask_all(unsigned int cpu, unsigned int set)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&wakeupgen_lock, flags);
+	if (set) {
+		_wakeupgen_save_masks(cpu);
+		_wakeupgen_set_all(cpu, WKG_MASK_ALL);
+	} else {
+		_wakeupgen_set_all(cpu, WKG_UNMASK_ALL);
+		_wakeupgen_restore_masks(cpu);
+	}
+	spin_unlock_irqrestore(&wakeupgen_lock, flags);
+}
+
+#ifdef CONFIG_CPU_PM
+/*
+ * Save WakeupGen interrupt context in SAR BANK3. Restore is done by
+ * ROM code. WakeupGen IP is integrated along with GIC to manage the
+ * interrupt wakeups from CPU low power states. It manages
+ * masking/unmasking of Shared peripheral interrupts(SPI). So the
+ * interrupt enable/disable control should be in sync and consistent
+ * at WakeupGen and GIC so that interrupts are not lost.
+ */
+static void irq_save_context(void)
+{
+	u32 i, val;
+
+	if (omap_rev() == OMAP4430_REV_ES1_0)
+		return;
+
+	if (!sar_base)
+		sar_base = omap4_get_sar_ram_base();
+
+	for (i = 0; i < NR_REG_BANKS; i++) {
+		/* Save the CPUx interrupt mask for IRQ 0 to 127 */
+		val = wakeupgen_readl(i, 0);
+		sar_writel(val, WAKEUPGENENB_OFFSET_CPU0, i);
+		val = wakeupgen_readl(i, 1);
+		sar_writel(val, WAKEUPGENENB_OFFSET_CPU1, i);
+
+		/*
+		 * Disable the secure interrupts for CPUx. The restore
+		 * code blindly restores secure and non-secure interrupt
+		 * masks from SAR RAM. Secure interrupts are not suppose
+		 * to be enabled from HLOS. So overwrite the SAR location
+		 * so that the secure interrupt remains disabled.
+		 */
+		sar_writel(0x0, WAKEUPGENENB_SECURE_OFFSET_CPU0, i);
+		sar_writel(0x0, WAKEUPGENENB_SECURE_OFFSET_CPU1, i);
+	}
+
+	/* Save AuxBoot* registers */
+	val = __raw_readl(wakeupgen_base + OMAP_AUX_CORE_BOOT_0);
+	__raw_writel(val, sar_base + AUXCOREBOOT0_OFFSET);
+	val = __raw_readl(wakeupgen_base + OMAP_AUX_CORE_BOOT_0);
+	__raw_writel(val, sar_base + AUXCOREBOOT1_OFFSET);
+
+	/* Save SyncReq generation logic */
+	val = __raw_readl(wakeupgen_base + OMAP_AUX_CORE_BOOT_0);
+	__raw_writel(val, sar_base + AUXCOREBOOT0_OFFSET);
+	val = __raw_readl(wakeupgen_base + OMAP_AUX_CORE_BOOT_0);
+	__raw_writel(val, sar_base + AUXCOREBOOT1_OFFSET);
+
+	/* Save SyncReq generation logic */
+	val = __raw_readl(wakeupgen_base + OMAP_PTMSYNCREQ_MASK);
+	__raw_writel(val, sar_base + PTMSYNCREQ_MASK_OFFSET);
+	val = __raw_readl(wakeupgen_base + OMAP_PTMSYNCREQ_EN);
+	__raw_writel(val, sar_base + PTMSYNCREQ_EN_OFFSET);
+
+	/* Set the Backup Bit Mask status */
+	val = __raw_readl(sar_base + SAR_BACKUP_STATUS_OFFSET);
+	val |= SAR_BACKUP_STATUS_WAKEUPGEN;
+	__raw_writel(val, sar_base + SAR_BACKUP_STATUS_OFFSET);
+}
+
+/*
+ * Clear WakeupGen SAR backup status.
+ */
+void irq_sar_clear(void)
+{
+	u32 val;
+	val = __raw_readl(sar_base + SAR_BACKUP_STATUS_OFFSET);
+	val &= ~SAR_BACKUP_STATUS_WAKEUPGEN;
+	__raw_writel(val, sar_base + SAR_BACKUP_STATUS_OFFSET);
+}
+
+/*
+ * Save GIC and Wakeupgen interrupt context using secure API
+ * for HS/EMU devices.
+ */
+static void irq_save_secure_context(void)
+{
+	u32 ret;
+	ret = omap_secure_dispatcher(OMAP4_HAL_SAVEGIC_INDEX,
+				FLAG_START_CRITICAL,
+				0, 0, 0, 0, 0);
+	if (ret != API_HAL_RET_VALUE_OK)
+		pr_err("GIC and Wakeupgen context save failed\n");
+}
+#endif
+
+#ifdef CONFIG_HOTPLUG_CPU
+static int __cpuinit irq_cpu_hotplug_notify(struct notifier_block *self,
+					 unsigned long action, void *hcpu)
+{
+	unsigned int cpu = (unsigned int)hcpu;
+
+	switch (action) {
+	case CPU_ONLINE:
+		wakeupgen_irqmask_all(cpu, 0);
+		break;
+	case CPU_DEAD:
+		wakeupgen_irqmask_all(cpu, 1);
+		break;
+	}
+	return NOTIFY_OK;
+}
+
+static struct notifier_block __refdata irq_hotplug_notifier = {
+	.notifier_call = irq_cpu_hotplug_notify,
+};
+
+static void __init irq_hotplug_init(void)
+{
+	register_hotcpu_notifier(&irq_hotplug_notifier);
+}
+#else
+static void __init irq_hotplug_init(void)
+{}
+#endif
+
+#ifdef CONFIG_CPU_PM
+static int irq_notifier(struct notifier_block *self, unsigned long cmd,	void *v)
+{
+	switch (cmd) {
+	case CPU_CLUSTER_PM_ENTER:
+		if (omap_type() == OMAP2_DEVICE_TYPE_GP)
+			irq_save_context();
+		else
+			irq_save_secure_context();
+		break;
+	case CPU_CLUSTER_PM_EXIT:
+		if (omap_type() == OMAP2_DEVICE_TYPE_GP)
+			irq_sar_clear();
+		break;
+	}
+	return NOTIFY_OK;
+}
+
+static struct notifier_block irq_notifier_block = {
+	.notifier_call = irq_notifier,
+};
+
+static void __init irq_pm_init(void)
+{
+	cpu_pm_register_notifier(&irq_notifier_block);
+}
+#else
+static void __init irq_pm_init(void)
+{}
+#endif
+
+/*
+ * Initialise the wakeupgen module.
+ */
+int __init omap_wakeupgen_init(void)
+{
+	int i;
+	unsigned int boot_cpu = smp_processor_id();
+
+	/* Not supported on OMAP4 ES1.0 silicon */
+	if (omap_rev() == OMAP4430_REV_ES1_0) {
+		WARN(1, "WakeupGen: Not supported on OMAP4430 ES1.0\n");
+		return -EPERM;
+	}
+
+	/* Static mapping, never released */
+	wakeupgen_base = ioremap(OMAP44XX_WKUPGEN_BASE, SZ_4K);
+	if (WARN_ON(!wakeupgen_base))
+		return -ENOMEM;
+
+	/* Clear all IRQ bitmasks at wakeupGen level */
+	for (i = 0; i < NR_REG_BANKS; i++) {
+		wakeupgen_writel(0, i, CPU0_ID);
+		wakeupgen_writel(0, i, CPU1_ID);
+	}
+
+	/*
+	 * Override GIC architecture specific functions to add
+	 * OMAP WakeupGen interrupt controller along with GIC
+	 */
+	gic_arch_extn.irq_mask = wakeupgen_mask;
+	gic_arch_extn.irq_unmask = wakeupgen_unmask;
+	gic_arch_extn.flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE;
+
+	/*
+	 * FIXME: Add support to set_smp_affinity() once the core
+	 * GIC code has necessary hooks in place.
+	 */
+
+	/* Associate all the IRQs to boot CPU like GIC init does. */
+	for (i = 0; i < NR_IRQS; i++)
+		irq_target_cpu[i] = boot_cpu;
+
+	irq_hotplug_init();
+	irq_pm_init();
+
+	return 0;
+}
diff --git a/arch/arm/mach-omap2/omap4-common.c b/arch/arm/mach-omap2/omap4-common.c
index beecfdd56ea..bc16c818c6b 100644
--- a/arch/arm/mach-omap2/omap4-common.c
+++ b/arch/arm/mach-omap2/omap4-common.c
@@ -15,18 +15,73 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/platform_device.h>
+#include <linux/memblock.h>
 
 #include <asm/hardware/gic.h>
 #include <asm/hardware/cache-l2x0.h>
+#include <asm/mach/map.h>
 
 #include <plat/irqs.h>
+#include <plat/sram.h>
 
 #include <mach/hardware.h>
+#include <mach/omap-wakeupgen.h>
 
 #include "common.h"
+#include "omap4-sar-layout.h"
 
 #ifdef CONFIG_CACHE_L2X0
-void __iomem *l2cache_base;
+static void __iomem *l2cache_base;
+#endif
+
+static void __iomem *sar_ram_base;
+
+#ifdef CONFIG_OMAP4_ERRATA_I688
+/* Used to implement memory barrier on DRAM path */
+#define OMAP4_DRAM_BARRIER_VA			0xfe600000
+
+void __iomem *dram_sync, *sram_sync;
+
+void omap_bus_sync(void)
+{
+	if (dram_sync && sram_sync) {
+		writel_relaxed(readl_relaxed(dram_sync), dram_sync);
+		writel_relaxed(readl_relaxed(sram_sync), sram_sync);
+		isb();
+	}
+}
+
+static int __init omap_barriers_init(void)
+{
+	struct map_desc dram_io_desc[1];
+	phys_addr_t paddr;
+	u32 size;
+
+	if (!cpu_is_omap44xx())
+		return -ENODEV;
+
+	size = ALIGN(PAGE_SIZE, SZ_1M);
+	paddr = memblock_alloc(size, SZ_1M);
+	if (!paddr) {
+		pr_err("%s: failed to reserve 4 Kbytes\n", __func__);
+		return -ENOMEM;
+	}
+	memblock_free(paddr, size);
+	memblock_remove(paddr, size);
+	dram_io_desc[0].virtual = OMAP4_DRAM_BARRIER_VA;
+	dram_io_desc[0].pfn = __phys_to_pfn(paddr);
+	dram_io_desc[0].length = size;
+	dram_io_desc[0].type = MT_MEMORY_SO;
+	iotable_init(dram_io_desc, ARRAY_SIZE(dram_io_desc));
+	dram_sync = (void __iomem *) dram_io_desc[0].virtual;
+	sram_sync = (void __iomem *) OMAP4_SRAM_VA;
+
+	pr_info("OMAP4: Map 0x%08llx to 0x%08lx for dram barrier\n",
+		(long long) paddr, dram_io_desc[0].virtual);
+
+	return 0;
+}
+core_initcall(omap_barriers_init);
 #endif
 
 void __init gic_init_irq(void)
@@ -42,11 +97,18 @@ void __init gic_init_irq(void)
 	omap_irq_base = ioremap(OMAP44XX_GIC_CPU_BASE, SZ_512);
 	BUG_ON(!omap_irq_base);
 
+	omap_wakeupgen_init();
+
 	gic_init(0, 29, gic_dist_base_addr, omap_irq_base);
 }
 
 #ifdef CONFIG_CACHE_L2X0
 
+void __iomem *omap4_get_l2cache_base(void)
+{
+	return l2cache_base;
+}
+
 static void omap4_l2x0_disable(void)
 {
 	/* Disable PL310 L2 Cache controller */
@@ -72,7 +134,8 @@ static int __init omap_l2_cache_init(void)
 
 	/* Static mapping, never released */
 	l2cache_base = ioremap(OMAP44XX_L2CACHE_BASE, SZ_4K);
-	BUG_ON(!l2cache_base);
+	if (WARN_ON(!l2cache_base))
+		return -ENOMEM;
 
 	/*
 	 * 16-way associativity, parity disabled
@@ -112,3 +175,30 @@ static int __init omap_l2_cache_init(void)
 }
 early_initcall(omap_l2_cache_init);
 #endif
+
+void __iomem *omap4_get_sar_ram_base(void)
+{
+	return sar_ram_base;
+}
+
+/*
+ * SAR RAM used to save and restore the HW
+ * context in low power modes
+ */
+static int __init omap4_sar_ram_init(void)
+{
+	/*
+	 * To avoid code running on other OMAPs in
+	 * multi-omap builds
+	 */
+	if (!cpu_is_omap44xx())
+		return -ENOMEM;
+
+	/* Static mapping, never released */
+	sar_ram_base = ioremap(OMAP44XX_SAR_RAM_BASE, SZ_16K);
+	if (WARN_ON(!sar_ram_base))
+		return -ENOMEM;
+
+	return 0;
+}
+early_initcall(omap4_sar_ram_init);
diff --git a/arch/arm/mach-omap2/omap4-sar-layout.h b/arch/arm/mach-omap2/omap4-sar-layout.h
new file mode 100644
index 00000000000..fe5b545ad44
--- /dev/null
+++ b/arch/arm/mach-omap2/omap4-sar-layout.h
@@ -0,0 +1,50 @@
+/*
+ * omap4-sar-layout.h: OMAP4 SAR RAM layout header file
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef OMAP_ARCH_OMAP4_SAR_LAYOUT_H
+#define OMAP_ARCH_OMAP4_SAR_LAYOUT_H
+
+/*
+ * SAR BANK offsets from base address OMAP44XX_SAR_RAM_BASE
+ */
+#define SAR_BANK1_OFFSET		0x0000
+#define SAR_BANK2_OFFSET		0x1000
+#define SAR_BANK3_OFFSET		0x2000
+#define SAR_BANK4_OFFSET		0x3000
+
+/* Scratch pad memory offsets from SAR_BANK1 */
+#define SCU_OFFSET0				0xd00
+#define SCU_OFFSET1				0xd04
+#define OMAP_TYPE_OFFSET			0xd10
+#define L2X0_SAVE_OFFSET0			0xd14
+#define L2X0_SAVE_OFFSET1			0xd18
+#define L2X0_AUXCTRL_OFFSET			0xd1c
+#define L2X0_PREFETCH_CTRL_OFFSET		0xd20
+
+/* CPUx Wakeup Non-Secure Physical Address offsets in SAR_BANK3 */
+#define CPU0_WAKEUP_NS_PA_ADDR_OFFSET		0xa04
+#define CPU1_WAKEUP_NS_PA_ADDR_OFFSET		0xa08
+
+#define SAR_BACKUP_STATUS_OFFSET		(SAR_BANK3_OFFSET + 0x500)
+#define SAR_SECURE_RAM_SIZE_OFFSET		(SAR_BANK3_OFFSET + 0x504)
+#define SAR_SECRAM_SAVED_AT_OFFSET		(SAR_BANK3_OFFSET + 0x508)
+
+/* WakeUpGen save restore offset from OMAP44XX_SAR_RAM_BASE */
+#define WAKEUPGENENB_OFFSET_CPU0		(SAR_BANK3_OFFSET + 0x684)
+#define WAKEUPGENENB_SECURE_OFFSET_CPU0		(SAR_BANK3_OFFSET + 0x694)
+#define WAKEUPGENENB_OFFSET_CPU1		(SAR_BANK3_OFFSET + 0x6a4)
+#define WAKEUPGENENB_SECURE_OFFSET_CPU1		(SAR_BANK3_OFFSET + 0x6b4)
+#define AUXCOREBOOT0_OFFSET			(SAR_BANK3_OFFSET + 0x6c4)
+#define AUXCOREBOOT1_OFFSET			(SAR_BANK3_OFFSET + 0x6c8)
+#define PTMSYNCREQ_MASK_OFFSET			(SAR_BANK3_OFFSET + 0x6cc)
+#define PTMSYNCREQ_EN_OFFSET			(SAR_BANK3_OFFSET + 0x6d0)
+#define SAR_BACKUP_STATUS_WAKEUPGEN		0x10
+
+#endif
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index 373d1f15c4e..5192cabb40e 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -136,6 +136,7 @@
 #include <linux/list.h>
 #include <linux/mutex.h>
 #include <linux/spinlock.h>
+#include <linux/slab.h>
 
 #include "common.h"
 #include <plat/cpu.h>
@@ -381,6 +382,51 @@ static int _set_module_autoidle(struct omap_hwmod *oh, u8 autoidle,
 }
 
 /**
+ * _set_idle_ioring_wakeup - enable/disable IO pad wakeup on hwmod idle for mux
+ * @oh: struct omap_hwmod *
+ * @set_wake: bool value indicating to set (true) or clear (false) wakeup enable
+ *
+ * Set or clear the I/O pad wakeup flag in the mux entries for the
+ * hwmod @oh.  This function changes the @oh->mux->pads_dynamic array
+ * in memory.  If the hwmod is currently idled, and the new idle
+ * values don't match the previous ones, this function will also
+ * update the SCM PADCTRL registers.  Otherwise, if the hwmod is not
+ * currently idled, this function won't touch the hardware: the new
+ * mux settings are written to the SCM PADCTRL registers when the
+ * hwmod is idled.  No return value.
+ */
+static void _set_idle_ioring_wakeup(struct omap_hwmod *oh, bool set_wake)
+{
+	struct omap_device_pad *pad;
+	bool change = false;
+	u16 prev_idle;
+	int j;
+
+	if (!oh->mux || !oh->mux->enabled)
+		return;
+
+	for (j = 0; j < oh->mux->nr_pads_dynamic; j++) {
+		pad = oh->mux->pads_dynamic[j];
+
+		if (!(pad->flags & OMAP_DEVICE_PAD_WAKEUP))
+			continue;
+
+		prev_idle = pad->idle;
+
+		if (set_wake)
+			pad->idle |= OMAP_WAKEUP_EN;
+		else
+			pad->idle &= ~OMAP_WAKEUP_EN;
+
+		if (prev_idle != pad->idle)
+			change = true;
+	}
+
+	if (change && oh->_state == _HWMOD_STATE_IDLE)
+		omap_hwmod_mux(oh->mux, _HWMOD_STATE_IDLE);
+}
+
+/**
  * _enable_wakeup: set OCP_SYSCONFIG.ENAWAKEUP bit in the hardware
  * @oh: struct omap_hwmod *
  *
@@ -1449,6 +1495,25 @@ static int _enable(struct omap_hwmod *oh)
 
 	pr_debug("omap_hwmod: %s: enabling\n", oh->name);
 
+	/*
+	 * hwmods with HWMOD_INIT_NO_IDLE flag set are left
+	 * in enabled state at init.
+	 * Now that someone is really trying to enable them,
+	 * just ensure that the hwmod mux is set.
+	 */
+	if (oh->_int_flags & _HWMOD_SKIP_ENABLE) {
+		/*
+		 * If the caller has mux data populated, do the mux'ing
+		 * which wouldn't have been done as part of the _enable()
+		 * done during setup.
+		 */
+		if (oh->mux)
+			omap_hwmod_mux(oh->mux, _HWMOD_STATE_ENABLED);
+
+		oh->_int_flags &= ~_HWMOD_SKIP_ENABLE;
+		return 0;
+	}
+
 	if (oh->_state != _HWMOD_STATE_INITIALIZED &&
 	    oh->_state != _HWMOD_STATE_IDLE &&
 	    oh->_state != _HWMOD_STATE_DISABLED) {
@@ -1744,8 +1809,10 @@ static int _setup(struct omap_hwmod *oh, void *data)
 	 * it should be set by the core code as a runtime flag during startup
 	 */
 	if ((oh->flags & HWMOD_INIT_NO_IDLE) &&
-	    (postsetup_state == _HWMOD_STATE_IDLE))
+	    (postsetup_state == _HWMOD_STATE_IDLE)) {
+		oh->_int_flags |= _HWMOD_SKIP_ENABLE;
 		postsetup_state = _HWMOD_STATE_ENABLED;
+	}
 
 	if (postsetup_state == _HWMOD_STATE_IDLE)
 		_idle(oh);
@@ -2416,6 +2483,7 @@ int omap_hwmod_enable_wakeup(struct omap_hwmod *oh)
 	v = oh->_sysc_cache;
 	_enable_wakeup(oh, &v);
 	_write_sysconfig(v, oh);
+	_set_idle_ioring_wakeup(oh, true);
 	spin_unlock_irqrestore(&oh->_lock, flags);
 
 	return 0;
@@ -2446,6 +2514,7 @@ int omap_hwmod_disable_wakeup(struct omap_hwmod *oh)
 	v = oh->_sysc_cache;
 	_disable_wakeup(oh, &v);
 	_write_sysconfig(v, oh);
+	_set_idle_ioring_wakeup(oh, false);
 	spin_unlock_irqrestore(&oh->_lock, flags);
 
 	return 0;
@@ -2662,3 +2731,57 @@ int omap_hwmod_no_setup_reset(struct omap_hwmod *oh)
 
 	return 0;
 }
+
+/**
+ * omap_hwmod_pad_route_irq - route an I/O pad wakeup to a particular MPU IRQ
+ * @oh: struct omap_hwmod * containing hwmod mux entries
+ * @pad_idx: array index in oh->mux of the hwmod mux entry to route wakeup
+ * @irq_idx: the hwmod mpu_irqs array index of the IRQ to trigger on wakeup
+ *
+ * When an I/O pad wakeup arrives for the dynamic or wakeup hwmod mux
+ * entry number @pad_idx for the hwmod @oh, trigger the interrupt
+ * service routine for the hwmod's mpu_irqs array index @irq_idx.  If
+ * this function is not called for a given pad_idx, then the ISR
+ * associated with @oh's first MPU IRQ will be triggered when an I/O
+ * pad wakeup occurs on that pad.  Note that @pad_idx is the index of
+ * the _dynamic or wakeup_ entry: if there are other entries not
+ * marked with OMAP_DEVICE_PAD_WAKEUP or OMAP_DEVICE_PAD_REMUX, these
+ * entries are NOT COUNTED in the dynamic pad index.  This function
+ * must be called separately for each pad that requires its interrupt
+ * to be re-routed this way.  Returns -EINVAL if there is an argument
+ * problem or if @oh does not have hwmod mux entries or MPU IRQs;
+ * returns -ENOMEM if memory cannot be allocated; or 0 upon success.
+ *
+ * XXX This function interface is fragile.  Rather than using array
+ * indexes, which are subject to unpredictable change, it should be
+ * using hwmod IRQ names, and some other stable key for the hwmod mux
+ * pad records.
+ */
+int omap_hwmod_pad_route_irq(struct omap_hwmod *oh, int pad_idx, int irq_idx)
+{
+	int nr_irqs;
+
+	might_sleep();
+
+	if (!oh || !oh->mux || !oh->mpu_irqs || pad_idx < 0 ||
+	    pad_idx >= oh->mux->nr_pads_dynamic)
+		return -EINVAL;
+
+	/* Check the number of available mpu_irqs */
+	for (nr_irqs = 0; oh->mpu_irqs[nr_irqs].irq >= 0; nr_irqs++)
+		;
+
+	if (irq_idx >= nr_irqs)
+		return -EINVAL;
+
+	if (!oh->mux->irqs) {
+		/* XXX What frees this? */
+		oh->mux->irqs = kzalloc(sizeof(int) * oh->mux->nr_pads_dynamic,
+			GFP_KERNEL);
+		if (!oh->mux->irqs)
+			return -ENOMEM;
+	}
+	oh->mux->irqs[pad_idx] = irq_idx;
+
+	return 0;
+}
diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h
index 4e166add2f3..b737b11e449 100644
--- a/arch/arm/mach-omap2/pm.h
+++ b/arch/arm/mach-omap2/pm.h
@@ -21,6 +21,7 @@ extern void omap_sram_idle(void);
 extern int omap3_can_sleep(void);
 extern int omap_set_pwrdm_state(struct powerdomain *pwrdm, u32 state);
 extern int omap3_idle_init(void);
+extern int omap4_idle_init(void);
 
 #if defined(CONFIG_PM_OPP)
 extern int omap3_opp_init(void);
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index ef8595c8029..b8822f8b289 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -30,7 +30,6 @@
 #include <linux/irq.h>
 #include <linux/time.h>
 #include <linux/gpio.h>
-#include <linux/console.h>
 
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
@@ -127,27 +126,11 @@ static void omap2_enter_full_retention(void)
 	if (omap_irq_pending())
 		goto no_sleep;
 
-	/* Block console output in case it is on one of the OMAP UARTs */
-	if (!is_suspending())
-		if (!console_trylock())
-			goto no_sleep;
-
-	omap_uart_prepare_idle(0);
-	omap_uart_prepare_idle(1);
-	omap_uart_prepare_idle(2);
-
 	/* Jump to SRAM suspend code */
 	omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
 			   OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
 			   OMAP_SDRC_REGADDR(SDRC_POWER));
 
-	omap_uart_resume_idle(2);
-	omap_uart_resume_idle(1);
-	omap_uart_resume_idle(0);
-
-	if (!is_suspending())
-		console_unlock();
-
 no_sleep:
 	omap2_gpio_resume_after_idle();
 
@@ -239,8 +222,6 @@ static int omap2_can_sleep(void)
 {
 	if (omap2_fclks_active())
 		return 0;
-	if (!omap_uart_can_sleep())
-		return 0;
 	if (osc_ck->usecount > 1)
 		return 0;
 	if (omap_dma_running())
@@ -291,7 +272,6 @@ static int omap2_pm_suspend(void)
 	mir1 = omap_readl(0x480fe0a4);
 	omap_writel(1 << 5, 0x480fe0ac);
 
-	omap_uart_prepare_suspend();
 	omap2_enter_full_retention();
 
 	omap_writel(mir1, 0x480fe0a4);
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index fa637dfdda5..fc698757892 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -28,7 +28,6 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/slab.h>
-#include <linux/console.h>
 #include <trace/events/power.h>
 
 #include <asm/suspend.h>
@@ -36,7 +35,6 @@
 #include <plat/sram.h>
 #include "clockdomain.h"
 #include "powerdomain.h"
-#include <plat/serial.h>
 #include <plat/sdrc.h>
 #include <plat/prcm.h>
 #include <plat/gpmc.h>
@@ -54,15 +52,6 @@
 
 #ifdef CONFIG_SUSPEND
 static suspend_state_t suspend_state = PM_SUSPEND_ON;
-static inline bool is_suspending(void)
-{
-	return (suspend_state != PM_SUSPEND_ON) && console_suspend_enabled;
-}
-#else
-static inline bool is_suspending(void)
-{
-	return false;
-}
 #endif
 
 /* pm34xx errata defined in pm.h */
@@ -195,7 +184,7 @@ static void omap3_save_secure_ram_context(void)
  * that any peripheral wake-up events occurring while attempting to
  * clear the PM_WKST_x are detected and cleared.
  */
-static int prcm_clear_mod_irqs(s16 module, u8 regs)
+static int prcm_clear_mod_irqs(s16 module, u8 regs, u32 ignore_bits)
 {
 	u32 wkst, fclk, iclk, clken;
 	u16 wkst_off = (regs == 3) ? OMAP3430ES2_PM_WKST3 : PM_WKST1;
@@ -207,6 +196,7 @@ static int prcm_clear_mod_irqs(s16 module, u8 regs)
 
 	wkst = omap2_prm_read_mod_reg(module, wkst_off);
 	wkst &= omap2_prm_read_mod_reg(module, grpsel_off);
+	wkst &= ~ignore_bits;
 	if (wkst) {
 		iclk = omap2_cm_read_mod_reg(module, iclk_off);
 		fclk = omap2_cm_read_mod_reg(module, fclk_off);
@@ -222,6 +212,7 @@ static int prcm_clear_mod_irqs(s16 module, u8 regs)
 			omap2_cm_set_mod_reg_bits(clken, module, fclk_off);
 			omap2_prm_write_mod_reg(wkst, module, wkst_off);
 			wkst = omap2_prm_read_mod_reg(module, wkst_off);
+			wkst &= ~ignore_bits;
 			c++;
 		}
 		omap2_cm_write_mod_reg(iclk, module, iclk_off);
@@ -231,76 +222,35 @@ static int prcm_clear_mod_irqs(s16 module, u8 regs)
 	return c;
 }
 
-static int _prcm_int_handle_wakeup(void)
+static irqreturn_t _prcm_int_handle_io(int irq, void *unused)
 {
 	int c;
 
-	c = prcm_clear_mod_irqs(WKUP_MOD, 1);
-	c += prcm_clear_mod_irqs(CORE_MOD, 1);
-	c += prcm_clear_mod_irqs(OMAP3430_PER_MOD, 1);
-	if (omap_rev() > OMAP3430_REV_ES1_0) {
-		c += prcm_clear_mod_irqs(CORE_MOD, 3);
-		c += prcm_clear_mod_irqs(OMAP3430ES2_USBHOST_MOD, 1);
-	}
+	c = prcm_clear_mod_irqs(WKUP_MOD, 1,
+		~(OMAP3430_ST_IO_MASK | OMAP3430_ST_IO_CHAIN_MASK));
 
-	return c;
+	return c ? IRQ_HANDLED : IRQ_NONE;
 }
 
-/*
- * PRCM Interrupt Handler
- *
- * The PRM_IRQSTATUS_MPU register indicates if there are any pending
- * interrupts from the PRCM for the MPU. These bits must be cleared in
- * order to clear the PRCM interrupt. The PRCM interrupt handler is
- * implemented to simply clear the PRM_IRQSTATUS_MPU in order to clear
- * the PRCM interrupt. Please note that bit 0 of the PRM_IRQSTATUS_MPU
- * register indicates that a wake-up event is pending for the MPU and
- * this bit can only be cleared if the all the wake-up events latched
- * in the various PM_WKST_x registers have been cleared. The interrupt
- * handler is implemented using a do-while loop so that if a wake-up
- * event occurred during the processing of the prcm interrupt handler
- * (setting a bit in the corresponding PM_WKST_x register and thus
- * preventing us from clearing bit 0 of the PRM_IRQSTATUS_MPU register)
- * this would be handled.
- */
-static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
+static irqreturn_t _prcm_int_handle_wakeup(int irq, void *unused)
 {
-	u32 irqenable_mpu, irqstatus_mpu;
-	int c = 0;
-
-	irqenable_mpu = omap2_prm_read_mod_reg(OCP_MOD,
-					 OMAP3_PRM_IRQENABLE_MPU_OFFSET);
-	irqstatus_mpu = omap2_prm_read_mod_reg(OCP_MOD,
-					 OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
-	irqstatus_mpu &= irqenable_mpu;
-
-	do {
-		if (irqstatus_mpu & (OMAP3430_WKUP_ST_MASK |
-				     OMAP3430_IO_ST_MASK)) {
-			c = _prcm_int_handle_wakeup();
-
-			/*
-			 * Is the MPU PRCM interrupt handler racing with the
-			 * IVA2 PRCM interrupt handler ?
-			 */
-			WARN(c == 0, "prcm: WARNING: PRCM indicated MPU wakeup "
-			     "but no wakeup sources are marked\n");
-		} else {
-			/* XXX we need to expand our PRCM interrupt handler */
-			WARN(1, "prcm: WARNING: PRCM interrupt received, but "
-			     "no code to handle it (%08x)\n", irqstatus_mpu);
-		}
-
-		omap2_prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
-					OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
-
-		irqstatus_mpu = omap2_prm_read_mod_reg(OCP_MOD,
-					OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
-		irqstatus_mpu &= irqenable_mpu;
+	int c;
 
-	} while (irqstatus_mpu);
+	/*
+	 * Clear all except ST_IO and ST_IO_CHAIN for wkup module,
+	 * these are handled in a separate handler to avoid acking
+	 * IO events before parsing in mux code
+	 */
+	c = prcm_clear_mod_irqs(WKUP_MOD, 1,
+		OMAP3430_ST_IO_MASK | OMAP3430_ST_IO_CHAIN_MASK);
+	c += prcm_clear_mod_irqs(CORE_MOD, 1, 0);
+	c += prcm_clear_mod_irqs(OMAP3430_PER_MOD, 1, 0);
+	if (omap_rev() > OMAP3430_REV_ES1_0) {
+		c += prcm_clear_mod_irqs(CORE_MOD, 3, 0);
+		c += prcm_clear_mod_irqs(OMAP3430ES2_USBHOST_MOD, 1, 0);
+	}
 
-	return IRQ_HANDLED;
+	return c ? IRQ_HANDLED : IRQ_NONE;
 }
 
 static void omap34xx_save_context(u32 *save)
@@ -376,20 +326,11 @@ void omap_sram_idle(void)
 			omap3_enable_io_chain();
 	}
 
-	/* Block console output in case it is on one of the OMAP UARTs */
-	if (!is_suspending())
-		if (per_next_state < PWRDM_POWER_ON ||
-		    core_next_state < PWRDM_POWER_ON)
-			if (!console_trylock())
-				goto console_still_active;
-
 	pwrdm_pre_transition();
 
 	/* PER */
 	if (per_next_state < PWRDM_POWER_ON) {
 		per_going_off = (per_next_state == PWRDM_POWER_OFF) ? 1 : 0;
-		omap_uart_prepare_idle(2);
-		omap_uart_prepare_idle(3);
 		omap2_gpio_prepare_for_idle(per_going_off);
 		if (per_next_state == PWRDM_POWER_OFF)
 				omap3_per_save_context();
@@ -397,8 +338,6 @@ void omap_sram_idle(void)
 
 	/* CORE */
 	if (core_next_state < PWRDM_POWER_ON) {
-		omap_uart_prepare_idle(0);
-		omap_uart_prepare_idle(1);
 		if (core_next_state == PWRDM_POWER_OFF) {
 			omap3_core_save_context();
 			omap3_cm_save_context();
@@ -447,8 +386,6 @@ void omap_sram_idle(void)
 			omap3_sram_restore_context();
 			omap2_sms_restore_context();
 		}
-		omap_uart_resume_idle(0);
-		omap_uart_resume_idle(1);
 		if (core_next_state == PWRDM_POWER_OFF)
 			omap2_prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
 					       OMAP3430_GR_MOD,
@@ -464,14 +401,8 @@ void omap_sram_idle(void)
 		omap2_gpio_resume_after_idle();
 		if (per_prev_state == PWRDM_POWER_OFF)
 			omap3_per_restore_context();
-		omap_uart_resume_idle(2);
-		omap_uart_resume_idle(3);
 	}
 
-	if (!is_suspending())
-		console_unlock();
-
-console_still_active:
 	/* Disable IO-PAD and IO-CHAIN wakeup */
 	if (omap3_has_io_wakeup() &&
 	    (per_next_state < PWRDM_POWER_ON ||
@@ -485,21 +416,11 @@ console_still_active:
 	clkdm_allow_idle(mpu_pwrdm->pwrdm_clkdms[0]);
 }
 
-int omap3_can_sleep(void)
-{
-	if (!omap_uart_can_sleep())
-		return 0;
-	return 1;
-}
-
 static void omap3_pm_idle(void)
 {
 	local_irq_disable();
 	local_fiq_disable();
 
-	if (!omap3_can_sleep())
-		goto out;
-
 	if (omap_irq_pending() || need_resched())
 		goto out;
 
@@ -533,7 +454,6 @@ static int omap3_pm_suspend(void)
 			goto restore;
 	}
 
-	omap_uart_prepare_suspend();
 	omap3_intc_suspend();
 
 	omap_sram_idle();
@@ -580,22 +500,27 @@ static int omap3_pm_begin(suspend_state_t state)
 {
 	disable_hlt();
 	suspend_state = state;
-	omap_uart_enable_irqs(0);
+	omap_prcm_irq_prepare();
 	return 0;
 }
 
 static void omap3_pm_end(void)
 {
 	suspend_state = PM_SUSPEND_ON;
-	omap_uart_enable_irqs(1);
 	enable_hlt();
 	return;
 }
 
+static void omap3_pm_finish(void)
+{
+	omap_prcm_irq_complete();
+}
+
 static const struct platform_suspend_ops omap_pm_ops = {
 	.begin		= omap3_pm_begin,
 	.end		= omap3_pm_end,
 	.enter		= omap3_pm_enter,
+	.finish		= omap3_pm_finish,
 	.valid		= suspend_valid_only_mem,
 };
 #endif /* CONFIG_SUSPEND */
@@ -701,10 +626,6 @@ static void __init prcm_setup_regs(void)
 			  OMAP3430_GRPSEL_GPT1_MASK |
 			  OMAP3430_GRPSEL_GPT12_MASK,
 			  WKUP_MOD, OMAP3430_PM_MPUGRPSEL);
-	/* For some reason IO doesn't generate wakeup event even if
-	 * it is selected to mpu wakeup goup */
-	omap2_prm_write_mod_reg(OMAP3430_IO_EN_MASK | OMAP3430_WKUP_EN_MASK,
-			  OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
 
 	/* Enable PM_WKEN to support DSS LPR */
 	omap2_prm_write_mod_reg(OMAP3430_PM_WKEN_DSS_EN_DSS_MASK,
@@ -881,12 +802,21 @@ static int __init omap3_pm_init(void)
 	 * supervised mode for powerdomains */
 	prcm_setup_regs();
 
-	ret = request_irq(INT_34XX_PRCM_MPU_IRQ,
-			  (irq_handler_t)prcm_interrupt_handler,
-			  IRQF_DISABLED, "prcm", NULL);
+	ret = request_irq(omap_prcm_event_to_irq("wkup"),
+		_prcm_int_handle_wakeup, IRQF_NO_SUSPEND, "pm_wkup", NULL);
+
+	if (ret) {
+		pr_err("pm: Failed to request pm_wkup irq\n");
+		goto err1;
+	}
+
+	/* IO interrupt is shared with mux code */
+	ret = request_irq(omap_prcm_event_to_irq("io"),
+		_prcm_int_handle_io, IRQF_SHARED | IRQF_NO_SUSPEND, "pm_io",
+		omap3_pm_init);
+
 	if (ret) {
-		printk(KERN_ERR "request_irq failed to register for 0x%x\n",
-		       INT_34XX_PRCM_MPU_IRQ);
+		pr_err("pm: Failed to request pm_io irq\n");
 		goto err1;
 	}
 
diff --git a/arch/arm/mach-omap2/pm44xx.c b/arch/arm/mach-omap2/pm44xx.c
index 8edb015f561..c264ef7219c 100644
--- a/arch/arm/mach-omap2/pm44xx.c
+++ b/arch/arm/mach-omap2/pm44xx.c
@@ -1,8 +1,9 @@
 /*
  * OMAP4 Power Management Routines
  *
- * Copyright (C) 2010 Texas Instruments, Inc.
+ * Copyright (C) 2010-2011 Texas Instruments, Inc.
  * Rajendra Nayak <rnayak@ti.com>
+ * Santosh Shilimkar <santosh.shilimkar@ti.com>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -17,13 +18,16 @@
 #include <linux/slab.h>
 
 #include "common.h"
+#include "clockdomain.h"
 #include "powerdomain.h"
+#include "pm.h"
 
 struct power_state {
 	struct powerdomain *pwrdm;
 	u32 next_state;
 #ifdef CONFIG_SUSPEND
 	u32 saved_state;
+	u32 saved_logic_state;
 #endif
 	struct list_head node;
 };
@@ -33,7 +37,50 @@ static LIST_HEAD(pwrst_list);
 #ifdef CONFIG_SUSPEND
 static int omap4_pm_suspend(void)
 {
-	do_wfi();
+	struct power_state *pwrst;
+	int state, ret = 0;
+	u32 cpu_id = smp_processor_id();
+
+	/* Save current powerdomain state */
+	list_for_each_entry(pwrst, &pwrst_list, node) {
+		pwrst->saved_state = pwrdm_read_next_pwrst(pwrst->pwrdm);
+		pwrst->saved_logic_state = pwrdm_read_logic_retst(pwrst->pwrdm);
+	}
+
+	/* Set targeted power domain states by suspend */
+	list_for_each_entry(pwrst, &pwrst_list, node) {
+		omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state);
+		pwrdm_set_logic_retst(pwrst->pwrdm, PWRDM_POWER_OFF);
+	}
+
+	/*
+	 * For MPUSS to hit power domain retention(CSWR or OSWR),
+	 * CPU0 and CPU1 power domains need to be in OFF or DORMANT state,
+	 * since CPU power domain CSWR is not supported by hardware
+	 * Only master CPU follows suspend path. All other CPUs follow
+	 * CPU hotplug path in system wide suspend. On OMAP4, CPU power
+	 * domain CSWR is not supported by hardware.
+	 * More details can be found in OMAP4430 TRM section 4.3.4.2.
+	 */
+	omap4_enter_lowpower(cpu_id, PWRDM_POWER_OFF);
+
+	/* Restore next powerdomain state */
+	list_for_each_entry(pwrst, &pwrst_list, node) {
+		state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
+		if (state > pwrst->next_state) {
+			pr_info("Powerdomain (%s) didn't enter "
+			       "target state %d\n",
+			       pwrst->pwrdm->name, pwrst->next_state);
+			ret = -1;
+		}
+		omap_set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
+		pwrdm_set_logic_retst(pwrst->pwrdm, pwrst->saved_logic_state);
+	}
+	if (ret)
+		pr_crit("Could not enter target state in pm_suspend\n");
+	else
+		pr_info("Successfully put all powerdomains to target state\n");
+
 	return 0;
 }
 
@@ -73,6 +120,22 @@ static const struct platform_suspend_ops omap_pm_ops = {
 };
 #endif /* CONFIG_SUSPEND */
 
+/*
+ * Enable hardware supervised mode for all clockdomains if it's
+ * supported. Initiate sleep transition for other clockdomains, if
+ * they are not used
+ */
+static int __init clkdms_setup(struct clockdomain *clkdm, void *unused)
+{
+	if (clkdm->flags & CLKDM_CAN_ENABLE_AUTO)
+		clkdm_allow_idle(clkdm);
+	else if (clkdm->flags & CLKDM_CAN_FORCE_SLEEP &&
+			atomic_read(&clkdm->usecount) == 0)
+		clkdm_sleep(clkdm);
+	return 0;
+}
+
+
 static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
 {
 	struct power_state *pwrst;
@@ -80,14 +143,48 @@ static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
 	if (!pwrdm->pwrsts)
 		return 0;
 
+	/*
+	 * Skip CPU0 and CPU1 power domains. CPU1 is programmed
+	 * through hotplug path and CPU0 explicitly programmed
+	 * further down in the code path
+	 */
+	if (!strncmp(pwrdm->name, "cpu", 3))
+		return 0;
+
+	/*
+	 * FIXME: Remove this check when core retention is supported
+	 * Only MPUSS power domain is added in the list.
+	 */
+	if (strcmp(pwrdm->name, "mpu_pwrdm"))
+		return 0;
+
 	pwrst = kmalloc(sizeof(struct power_state), GFP_ATOMIC);
 	if (!pwrst)
 		return -ENOMEM;
+
 	pwrst->pwrdm = pwrdm;
-	pwrst->next_state = PWRDM_POWER_ON;
+	pwrst->next_state = PWRDM_POWER_RET;
 	list_add(&pwrst->node, &pwrst_list);
 
-	return pwrdm_set_next_pwrst(pwrst->pwrdm, pwrst->next_state);
+	return omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state);
+}
+
+/**
+ * omap_default_idle - OMAP4 default ilde routine.'
+ *
+ * Implements OMAP4 memory, IO ordering requirements which can't be addressed
+ * with default arch_idle() hook. Used by all CPUs with !CONFIG_CPUIDLE and
+ * by secondary CPU with CONFIG_CPUIDLE.
+ */
+static void omap_default_idle(void)
+{
+	local_irq_disable();
+	local_fiq_disable();
+
+	omap_do_wfi();
+
+	local_fiq_enable();
+	local_irq_enable();
 }
 
 /**
@@ -99,10 +196,17 @@ static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
 static int __init omap4_pm_init(void)
 {
 	int ret;
+	struct clockdomain *emif_clkdm, *mpuss_clkdm, *l3_1_clkdm;
+	struct clockdomain *ducati_clkdm, *l3_2_clkdm, *l4_per_clkdm;
 
 	if (!cpu_is_omap44xx())
 		return -ENODEV;
 
+	if (omap_rev() == OMAP4430_REV_ES1_0) {
+		WARN(1, "Power Management not supported on OMAP4430 ES1.0\n");
+		return -ENODEV;
+	}
+
 	pr_err("Power Management for TI OMAP4.\n");
 
 	ret = pwrdm_for_each(pwrdms_setup, NULL);
@@ -111,10 +215,51 @@ static int __init omap4_pm_init(void)
 		goto err2;
 	}
 
+	/*
+	 * The dynamic dependency between MPUSS -> MEMIF and
+	 * MPUSS -> L4_PER/L3_* and DUCATI -> L3_* doesn't work as
+	 * expected. The hardware recommendation is to enable static
+	 * dependencies for these to avoid system lock ups or random crashes.
+	 */
+	mpuss_clkdm = clkdm_lookup("mpuss_clkdm");
+	emif_clkdm = clkdm_lookup("l3_emif_clkdm");
+	l3_1_clkdm = clkdm_lookup("l3_1_clkdm");
+	l3_2_clkdm = clkdm_lookup("l3_2_clkdm");
+	l4_per_clkdm = clkdm_lookup("l4_per_clkdm");
+	ducati_clkdm = clkdm_lookup("ducati_clkdm");
+	if ((!mpuss_clkdm) || (!emif_clkdm) || (!l3_1_clkdm) ||
+		(!l3_2_clkdm) || (!ducati_clkdm) || (!l4_per_clkdm))
+		goto err2;
+
+	ret = clkdm_add_wkdep(mpuss_clkdm, emif_clkdm);
+	ret |= clkdm_add_wkdep(mpuss_clkdm, l3_1_clkdm);
+	ret |= clkdm_add_wkdep(mpuss_clkdm, l3_2_clkdm);
+	ret |= clkdm_add_wkdep(mpuss_clkdm, l4_per_clkdm);
+	ret |= clkdm_add_wkdep(ducati_clkdm, l3_1_clkdm);
+	ret |= clkdm_add_wkdep(ducati_clkdm, l3_2_clkdm);
+	if (ret) {
+		pr_err("Failed to add MPUSS -> L3/EMIF/L4PER, DUCATI -> L3 "
+				"wakeup dependency\n");
+		goto err2;
+	}
+
+	ret = omap4_mpuss_init();
+	if (ret) {
+		pr_err("Failed to initialise OMAP4 MPUSS\n");
+		goto err2;
+	}
+
+	(void) clkdm_for_each(clkdms_setup, NULL);
+
 #ifdef CONFIG_SUSPEND
 	suspend_set_ops(&omap_pm_ops);
 #endif /* CONFIG_SUSPEND */
 
+	/* Overwrite the default arch_idle() */
+	pm_idle = omap_default_idle;
+
+	omap4_idle_init();
+
 err2:
 	return ret;
 }
diff --git a/arch/arm/mach-omap2/prcm-common.h b/arch/arm/mach-omap2/prcm-common.h
index da2d80f5fcb..5aa5435e3ff 100644
--- a/arch/arm/mach-omap2/prcm-common.h
+++ b/arch/arm/mach-omap2/prcm-common.h
@@ -4,7 +4,7 @@
 /*
  * OMAP2/3 PRCM base and module definitions
  *
- * Copyright (C) 2007-2009 Texas Instruments, Inc.
+ * Copyright (C) 2007-2009, 2011 Texas Instruments, Inc.
  * Copyright (C) 2007-2009 Nokia Corporation
  *
  * Written by Paul Walmsley
@@ -410,6 +410,79 @@
 extern void __iomem *prm_base;
 extern void __iomem *cm_base;
 extern void __iomem *cm2_base;
+
+/**
+ * struct omap_prcm_irq - describes a PRCM interrupt bit
+ * @name: a short name describing the interrupt type, e.g. "wkup" or "io"
+ * @offset: the bit shift of the interrupt inside the IRQ{ENABLE,STATUS} regs
+ * @priority: should this interrupt be handled before @priority=false IRQs?
+ *
+ * Describes interrupt bits inside the PRM_IRQ{ENABLE,STATUS}_MPU* registers.
+ * On systems with multiple PRM MPU IRQ registers, the bitfields read from
+ * the registers are concatenated, so @offset could be > 31 on these systems -
+ * see omap_prm_irq_handler() for more details.  I/O ring interrupts should
+ * have @priority set to true.
+ */
+struct omap_prcm_irq {
+	const char *name;
+	unsigned int offset;
+	bool priority;
+};
+
+/**
+ * struct omap_prcm_irq_setup - PRCM interrupt controller details
+ * @ack: PRM register offset for the first PRM_IRQSTATUS_MPU register
+ * @mask: PRM register offset for the first PRM_IRQENABLE_MPU register
+ * @nr_regs: number of PRM_IRQ{STATUS,ENABLE}_MPU* registers
+ * @nr_irqs: number of entries in the @irqs array
+ * @irqs: ptr to an array of PRCM interrupt bits (see @nr_irqs)
+ * @irq: MPU IRQ asserted when a PRCM interrupt arrives
+ * @read_pending_irqs: fn ptr to determine if any PRCM IRQs are pending
+ * @ocp_barrier: fn ptr to force buffered PRM writes to complete
+ * @save_and_clear_irqen: fn ptr to save and clear IRQENABLE regs
+ * @restore_irqen: fn ptr to save and clear IRQENABLE regs
+ * @saved_mask: IRQENABLE regs are saved here during suspend
+ * @priority_mask: 1 bit per IRQ, set to 1 if omap_prcm_irq.priority = true
+ * @base_irq: base dynamic IRQ number, returned from irq_alloc_descs() in init
+ * @suspended: set to true after Linux suspend code has called our ->prepare()
+ * @suspend_save_flag: set to true after IRQ masks have been saved and disabled
+ *
+ * @saved_mask, @priority_mask, @base_irq, @suspended, and
+ * @suspend_save_flag are populated dynamically, and are not to be
+ * specified in static initializers.
+ */
+struct omap_prcm_irq_setup {
+	u16 ack;
+	u16 mask;
+	u8 nr_regs;
+	u8 nr_irqs;
+	const struct omap_prcm_irq *irqs;
+	int irq;
+	void (*read_pending_irqs)(unsigned long *events);
+	void (*ocp_barrier)(void);
+	void (*save_and_clear_irqen)(u32 *saved_mask);
+	void (*restore_irqen)(u32 *saved_mask);
+	u32 *saved_mask;
+	u32 *priority_mask;
+	int base_irq;
+	bool suspended;
+	bool suspend_save_flag;
+};
+
+/* OMAP_PRCM_IRQ: convenience macro for creating struct omap_prcm_irq records */
+#define OMAP_PRCM_IRQ(_name, _offset, _priority) {	\
+	.name = _name,					\
+	.offset = _offset,				\
+	.priority = _priority				\
+	}
+
+extern void omap_prcm_irq_cleanup(void);
+extern int omap_prcm_register_chain_handler(
+	struct omap_prcm_irq_setup *irq_setup);
+extern int omap_prcm_event_to_irq(const char *event);
+extern void omap_prcm_irq_prepare(void);
+extern void omap_prcm_irq_complete(void);
+
 # endif
 
 #endif
diff --git a/arch/arm/mach-omap2/prm2xxx_3xxx.c b/arch/arm/mach-omap2/prm2xxx_3xxx.c
index 9a08ba39732..c1c4d86a79a 100644
--- a/arch/arm/mach-omap2/prm2xxx_3xxx.c
+++ b/arch/arm/mach-omap2/prm2xxx_3xxx.c
@@ -1,7 +1,7 @@
 /*
  * OMAP2/3 PRM module functions
  *
- * Copyright (C) 2010 Texas Instruments, Inc.
+ * Copyright (C) 2010-2011 Texas Instruments, Inc.
  * Copyright (C) 2010 Nokia Corporation
  * Benoît Cousson
  * Paul Walmsley
@@ -27,6 +27,24 @@
 #include "prm-regbits-24xx.h"
 #include "prm-regbits-34xx.h"
 
+static const struct omap_prcm_irq omap3_prcm_irqs[] = {
+	OMAP_PRCM_IRQ("wkup",	0,	0),
+	OMAP_PRCM_IRQ("io",	9,	1),
+};
+
+static struct omap_prcm_irq_setup omap3_prcm_irq_setup = {
+	.ack			= OMAP3_PRM_IRQSTATUS_MPU_OFFSET,
+	.mask			= OMAP3_PRM_IRQENABLE_MPU_OFFSET,
+	.nr_regs		= 1,
+	.irqs			= omap3_prcm_irqs,
+	.nr_irqs		= ARRAY_SIZE(omap3_prcm_irqs),
+	.irq			= INT_34XX_PRCM_MPU_IRQ,
+	.read_pending_irqs	= &omap3xxx_prm_read_pending_irqs,
+	.ocp_barrier		= &omap3xxx_prm_ocp_barrier,
+	.save_and_clear_irqen	= &omap3xxx_prm_save_and_clear_irqen,
+	.restore_irqen		= &omap3xxx_prm_restore_irqen,
+};
+
 u32 omap2_prm_read_mod_reg(s16 module, u16 idx)
 {
 	return __raw_readl(prm_base + module + idx);
@@ -212,3 +230,80 @@ u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset)
 {
 	return omap2_prm_rmw_mod_reg_bits(mask, bits, OMAP3430_GR_MOD, offset);
 }
+
+/**
+ * omap3xxx_prm_read_pending_irqs - read pending PRM MPU IRQs into @events
+ * @events: ptr to a u32, preallocated by caller
+ *
+ * Read PRM_IRQSTATUS_MPU bits, AND'ed with the currently-enabled PRM
+ * MPU IRQs, and store the result into the u32 pointed to by @events.
+ * No return value.
+ */
+void omap3xxx_prm_read_pending_irqs(unsigned long *events)
+{
+	u32 mask, st;
+
+	/* XXX Can the mask read be avoided (e.g., can it come from RAM?) */
+	mask = omap2_prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
+	st = omap2_prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+
+	events[0] = mask & st;
+}
+
+/**
+ * omap3xxx_prm_ocp_barrier - force buffered MPU writes to the PRM to complete
+ *
+ * Force any buffered writes to the PRM IP block to complete.  Needed
+ * by the PRM IRQ handler, which reads and writes directly to the IP
+ * block, to avoid race conditions after acknowledging or clearing IRQ
+ * bits.  No return value.
+ */
+void omap3xxx_prm_ocp_barrier(void)
+{
+	omap2_prm_read_mod_reg(OCP_MOD, OMAP3_PRM_REVISION_OFFSET);
+}
+
+/**
+ * omap3xxx_prm_save_and_clear_irqen - save/clear PRM_IRQENABLE_MPU reg
+ * @saved_mask: ptr to a u32 array to save IRQENABLE bits
+ *
+ * Save the PRM_IRQENABLE_MPU register to @saved_mask.  @saved_mask
+ * must be allocated by the caller.  Intended to be used in the PRM
+ * interrupt handler suspend callback.  The OCP barrier is needed to
+ * ensure the write to disable PRM interrupts reaches the PRM before
+ * returning; otherwise, spurious interrupts might occur.  No return
+ * value.
+ */
+void omap3xxx_prm_save_and_clear_irqen(u32 *saved_mask)
+{
+	saved_mask[0] = omap2_prm_read_mod_reg(OCP_MOD,
+					       OMAP3_PRM_IRQENABLE_MPU_OFFSET);
+	omap2_prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
+
+	/* OCP barrier */
+	omap2_prm_read_mod_reg(OCP_MOD, OMAP3_PRM_REVISION_OFFSET);
+}
+
+/**
+ * omap3xxx_prm_restore_irqen - set PRM_IRQENABLE_MPU register from args
+ * @saved_mask: ptr to a u32 array of IRQENABLE bits saved previously
+ *
+ * Restore the PRM_IRQENABLE_MPU register from @saved_mask.  Intended
+ * to be used in the PRM interrupt handler resume callback to restore
+ * values saved by omap3xxx_prm_save_and_clear_irqen().  No OCP
+ * barrier should be needed here; any pending PRM interrupts will fire
+ * once the writes reach the PRM.  No return value.
+ */
+void omap3xxx_prm_restore_irqen(u32 *saved_mask)
+{
+	omap2_prm_write_mod_reg(saved_mask[0], OCP_MOD,
+				OMAP3_PRM_IRQENABLE_MPU_OFFSET);
+}
+
+static int __init omap3xxx_prcm_init(void)
+{
+	if (cpu_is_omap34xx())
+		return omap_prcm_register_chain_handler(&omap3_prcm_irq_setup);
+	return 0;
+}
+subsys_initcall(omap3xxx_prcm_init);
diff --git a/arch/arm/mach-omap2/prm2xxx_3xxx.h b/arch/arm/mach-omap2/prm2xxx_3xxx.h
index cef533df086..70ac2a19dc5 100644
--- a/arch/arm/mach-omap2/prm2xxx_3xxx.h
+++ b/arch/arm/mach-omap2/prm2xxx_3xxx.h
@@ -1,7 +1,7 @@
 /*
  * OMAP2/3 Power/Reset Management (PRM) register definitions
  *
- * Copyright (C) 2007-2009 Texas Instruments, Inc.
+ * Copyright (C) 2007-2009, 2011 Texas Instruments, Inc.
  * Copyright (C) 2008-2010 Nokia Corporation
  * Paul Walmsley
  *
@@ -314,6 +314,13 @@ void omap3_prm_vp_clear_txdone(u8 vp_id);
 extern u32 omap3_prm_vcvp_read(u8 offset);
 extern void omap3_prm_vcvp_write(u32 val, u8 offset);
 extern u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
+
+/* PRM interrupt-related functions */
+extern void omap3xxx_prm_read_pending_irqs(unsigned long *events);
+extern void omap3xxx_prm_ocp_barrier(void);
+extern void omap3xxx_prm_save_and_clear_irqen(u32 *saved_mask);
+extern void omap3xxx_prm_restore_irqen(u32 *saved_mask);
+
 #endif	/* CONFIG_ARCH_OMAP4 */
 
 #endif
diff --git a/arch/arm/mach-omap2/prm44xx.c b/arch/arm/mach-omap2/prm44xx.c
index dd885eecf22..33dd655e6aa 100644
--- a/arch/arm/mach-omap2/prm44xx.c
+++ b/arch/arm/mach-omap2/prm44xx.c
@@ -27,6 +27,24 @@
 #include "prcm44xx.h"
 #include "prminst44xx.h"
 
+static const struct omap_prcm_irq omap4_prcm_irqs[] = {
+	OMAP_PRCM_IRQ("wkup",   0,      0),
+	OMAP_PRCM_IRQ("io",     9,      1),
+};
+
+static struct omap_prcm_irq_setup omap4_prcm_irq_setup = {
+	.ack			= OMAP4_PRM_IRQSTATUS_MPU_OFFSET,
+	.mask			= OMAP4_PRM_IRQENABLE_MPU_OFFSET,
+	.nr_regs		= 2,
+	.irqs			= omap4_prcm_irqs,
+	.nr_irqs		= ARRAY_SIZE(omap4_prcm_irqs),
+	.irq			= OMAP44XX_IRQ_PRCM,
+	.read_pending_irqs	= &omap44xx_prm_read_pending_irqs,
+	.ocp_barrier		= &omap44xx_prm_ocp_barrier,
+	.save_and_clear_irqen	= &omap44xx_prm_save_and_clear_irqen,
+	.restore_irqen		= &omap44xx_prm_restore_irqen,
+};
+
 /* PRM low-level functions */
 
 /* Read a register in a CM/PRM instance in the PRM module */
@@ -121,3 +139,101 @@ u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset)
 					       OMAP4430_PRM_DEVICE_INST,
 					       offset);
 }
+
+static inline u32 _read_pending_irq_reg(u16 irqen_offs, u16 irqst_offs)
+{
+	u32 mask, st;
+
+	/* XXX read mask from RAM? */
+	mask = omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST, irqen_offs);
+	st = omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST, irqst_offs);
+
+	return mask & st;
+}
+
+/**
+ * omap44xx_prm_read_pending_irqs - read pending PRM MPU IRQs into @events
+ * @events: ptr to two consecutive u32s, preallocated by caller
+ *
+ * Read PRM_IRQSTATUS_MPU* bits, AND'ed with the currently-enabled PRM
+ * MPU IRQs, and store the result into the two u32s pointed to by @events.
+ * No return value.
+ */
+void omap44xx_prm_read_pending_irqs(unsigned long *events)
+{
+	events[0] = _read_pending_irq_reg(OMAP4_PRM_IRQENABLE_MPU_OFFSET,
+					  OMAP4_PRM_IRQSTATUS_MPU_OFFSET);
+
+	events[1] = _read_pending_irq_reg(OMAP4_PRM_IRQENABLE_MPU_2_OFFSET,
+					  OMAP4_PRM_IRQSTATUS_MPU_2_OFFSET);
+}
+
+/**
+ * omap44xx_prm_ocp_barrier - force buffered MPU writes to the PRM to complete
+ *
+ * Force any buffered writes to the PRM IP block to complete.  Needed
+ * by the PRM IRQ handler, which reads and writes directly to the IP
+ * block, to avoid race conditions after acknowledging or clearing IRQ
+ * bits.  No return value.
+ */
+void omap44xx_prm_ocp_barrier(void)
+{
+	omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST,
+				OMAP4_REVISION_PRM_OFFSET);
+}
+
+/**
+ * omap44xx_prm_save_and_clear_irqen - save/clear PRM_IRQENABLE_MPU* regs
+ * @saved_mask: ptr to a u32 array to save IRQENABLE bits
+ *
+ * Save the PRM_IRQENABLE_MPU and PRM_IRQENABLE_MPU_2 registers to
+ * @saved_mask.  @saved_mask must be allocated by the caller.
+ * Intended to be used in the PRM interrupt handler suspend callback.
+ * The OCP barrier is needed to ensure the write to disable PRM
+ * interrupts reaches the PRM before returning; otherwise, spurious
+ * interrupts might occur.  No return value.
+ */
+void omap44xx_prm_save_and_clear_irqen(u32 *saved_mask)
+{
+	saved_mask[0] =
+		omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST,
+					OMAP4_PRM_IRQSTATUS_MPU_OFFSET);
+	saved_mask[1] =
+		omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST,
+					OMAP4_PRM_IRQSTATUS_MPU_2_OFFSET);
+
+	omap4_prm_write_inst_reg(0, OMAP4430_PRM_DEVICE_INST,
+				 OMAP4_PRM_IRQENABLE_MPU_OFFSET);
+	omap4_prm_write_inst_reg(0, OMAP4430_PRM_DEVICE_INST,
+				 OMAP4_PRM_IRQENABLE_MPU_2_OFFSET);
+
+	/* OCP barrier */
+	omap4_prm_read_inst_reg(OMAP4430_PRM_DEVICE_INST,
+				OMAP4_REVISION_PRM_OFFSET);
+}
+
+/**
+ * omap44xx_prm_restore_irqen - set PRM_IRQENABLE_MPU* registers from args
+ * @saved_mask: ptr to a u32 array of IRQENABLE bits saved previously
+ *
+ * Restore the PRM_IRQENABLE_MPU and PRM_IRQENABLE_MPU_2 registers from
+ * @saved_mask.  Intended to be used in the PRM interrupt handler resume
+ * callback to restore values saved by omap44xx_prm_save_and_clear_irqen().
+ * No OCP barrier should be needed here; any pending PRM interrupts will fire
+ * once the writes reach the PRM.  No return value.
+ */
+void omap44xx_prm_restore_irqen(u32 *saved_mask)
+{
+	omap4_prm_write_inst_reg(saved_mask[0], OMAP4430_PRM_DEVICE_INST,
+				 OMAP4_PRM_IRQENABLE_MPU_OFFSET);
+	omap4_prm_write_inst_reg(saved_mask[1], OMAP4430_PRM_DEVICE_INST,
+				 OMAP4_PRM_IRQENABLE_MPU_2_OFFSET);
+}
+
+static int __init omap4xxx_prcm_init(void)
+{
+	if (cpu_is_omap44xx())
+		return omap_prcm_register_chain_handler(&omap4_prcm_irq_setup);
+	return 0;
+}
+subsys_initcall(omap4xxx_prcm_init);
diff --git a/arch/arm/mach-omap2/prm44xx.h b/arch/arm/mach-omap2/prm44xx.h
index 3d66ccd849d..7978092946d 100644
--- a/arch/arm/mach-omap2/prm44xx.h
+++ b/arch/arm/mach-omap2/prm44xx.h
@@ -1,7 +1,7 @@
 /*
  * OMAP44xx PRM instance offset macros
  *
- * Copyright (C) 2009-2010 Texas Instruments, Inc.
+ * Copyright (C) 2009-2011 Texas Instruments, Inc.
  * Copyright (C) 2009-2010 Nokia Corporation
  *
  * Paul Walmsley (paul@pwsan.com)
@@ -763,6 +763,12 @@ extern u32 omap4_prm_vcvp_read(u8 offset);
 extern void omap4_prm_vcvp_write(u32 val, u8 offset);
 extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
 
+/* PRM interrupt-related functions */
+extern void omap44xx_prm_read_pending_irqs(unsigned long *events);
+extern void omap44xx_prm_ocp_barrier(void);
+extern void omap44xx_prm_save_and_clear_irqen(u32 *saved_mask);
+extern void omap44xx_prm_restore_irqen(u32 *saved_mask);
+
 # endif
 
 #endif
diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c
new file mode 100644
index 00000000000..860118ab43e
--- /dev/null
+++ b/arch/arm/mach-omap2/prm_common.c
@@ -0,0 +1,320 @@
+/*
+ * OMAP2+ common Power & Reset Management (PRM) IP block functions
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * Tero Kristo <t-kristo@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *
+ * For historical purposes, the API used to configure the PRM
+ * interrupt handler refers to it as the "PRCM interrupt."  The
+ * underlying registers are located in the PRM on OMAP3/4.
+ *
+ * XXX This code should eventually be moved to a PRM driver.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+
+#include <mach/system.h>
+#include <plat/common.h>
+#include <plat/prcm.h>
+#include <plat/irqs.h>
+
+#include "prm2xxx_3xxx.h"
+#include "prm44xx.h"
+
+/*
+ * OMAP_PRCM_MAX_NR_PENDING_REG: maximum number of PRM_IRQ*_MPU regs
+ * XXX this is technically not needed, since
+ * omap_prcm_register_chain_handler() could allocate this based on the
+ * actual amount of memory needed for the SoC
+ */
+#define OMAP_PRCM_MAX_NR_PENDING_REG		2
+
+/*
+ * prcm_irq_chips: an array of all of the "generic IRQ chips" in use
+ * by the PRCM interrupt handler code.  There will be one 'chip' per
+ * PRM_{IRQSTATUS,IRQENABLE}_MPU register pair.  (So OMAP3 will have
+ * one "chip" and OMAP4 will have two.)
+ */
+static struct irq_chip_generic **prcm_irq_chips;
+
+/*
+ * prcm_irq_setup: the PRCM IRQ parameters for the hardware the code
+ * is currently running on.  Defined and passed by initialization code
+ * that calls omap_prcm_register_chain_handler().
+ */
+static struct omap_prcm_irq_setup *prcm_irq_setup;
+
+/* Private functions */
+
+/*
+ * Move priority events from events to priority_events array
+ */
+static void omap_prcm_events_filter_priority(unsigned long *events,
+	unsigned long *priority_events)
+{
+	int i;
+
+	for (i = 0; i < prcm_irq_setup->nr_regs; i++) {
+		priority_events[i] =
+			events[i] & prcm_irq_setup->priority_mask[i];
+		events[i] ^= priority_events[i];
+	}
+}
+
+/*
+ * PRCM Interrupt Handler
+ *
+ * This is a common handler for the OMAP PRCM interrupts. Pending
+ * interrupts are detected by a call to prcm_pending_events and
+ * dispatched accordingly. Clearing of the wakeup events should be
+ * done by the SoC specific individual handlers.
+ */
+static void omap_prcm_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	unsigned long pending[OMAP_PRCM_MAX_NR_PENDING_REG];
+	unsigned long priority_pending[OMAP_PRCM_MAX_NR_PENDING_REG];
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	unsigned int virtirq;
+	int nr_irqs = prcm_irq_setup->nr_regs * 32;
+
+	/*
+	 * If we are suspended, mask all interrupts from PRCM level,
+	 * this does not ack them, and they will be pending until we
+	 * re-enable the interrupts, at which point the
+	 * omap_prcm_irq_handler will be executed again.  The
+	 * _save_and_clear_irqen() function must ensure that the PRM
+	 * write to disable all IRQs has reached the PRM before
+	 * returning, or spurious PRCM interrupts may occur during
+	 * suspend.
+	 */
+	if (prcm_irq_setup->suspended) {
+		prcm_irq_setup->save_and_clear_irqen(prcm_irq_setup->saved_mask);
+		prcm_irq_setup->suspend_save_flag = true;
+	}
+
+	/*
+	 * Loop until all pending irqs are handled, since
+	 * generic_handle_irq() can cause new irqs to come
+	 */
+	while (!prcm_irq_setup->suspended) {
+		prcm_irq_setup->read_pending_irqs(pending);
+
+		/* No bit set, then all IRQs are handled */
+		if (find_first_bit(pending, nr_irqs) >= nr_irqs)
+			break;
+
+		omap_prcm_events_filter_priority(pending, priority_pending);
+
+		/*
+		 * Loop on all currently pending irqs so that new irqs
+		 * cannot starve previously pending irqs
+		 */
+
+		/* Serve priority events first */
+		for_each_set_bit(virtirq, priority_pending, nr_irqs)
+			generic_handle_irq(prcm_irq_setup->base_irq + virtirq);
+
+		/* Serve normal events next */
+		for_each_set_bit(virtirq, pending, nr_irqs)
+			generic_handle_irq(prcm_irq_setup->base_irq + virtirq);
+	}
+	if (chip->irq_ack)
+		chip->irq_ack(&desc->irq_data);
+	if (chip->irq_eoi)
+		chip->irq_eoi(&desc->irq_data);
+	chip->irq_unmask(&desc->irq_data);
+
+	prcm_irq_setup->ocp_barrier(); /* avoid spurious IRQs */
+}
+
+/* Public functions */
+
+/**
+ * omap_prcm_event_to_irq - given a PRCM event name, returns the
+ * corresponding IRQ on which the handler should be registered
+ * @name: name of the PRCM interrupt bit to look up - see struct omap_prcm_irq
+ *
+ * Returns the Linux internal IRQ ID corresponding to @name upon success,
+ * or -ENOENT upon failure.
+ */
+int omap_prcm_event_to_irq(const char *name)
+{
+	int i;
+
+	if (!prcm_irq_setup || !name)
+		return -ENOENT;
+
+	for (i = 0; i < prcm_irq_setup->nr_irqs; i++)
+		if (!strcmp(prcm_irq_setup->irqs[i].name, name))
+			return prcm_irq_setup->base_irq +
+				prcm_irq_setup->irqs[i].offset;
+
+	return -ENOENT;
+}
+
+/**
+ * omap_prcm_irq_cleanup - reverses memory allocated and other steps
+ * done by omap_prcm_register_chain_handler()
+ *
+ * No return value.
+ */
+void omap_prcm_irq_cleanup(void)
+{
+	int i;
+
+	if (!prcm_irq_setup) {
+		pr_err("PRCM: IRQ handler not initialized; cannot cleanup\n");
+		return;
+	}
+
+	if (prcm_irq_chips) {
+		for (i = 0; i < prcm_irq_setup->nr_regs; i++) {
+			if (prcm_irq_chips[i])
+				irq_remove_generic_chip(prcm_irq_chips[i],
+					0xffffffff, 0, 0);
+			prcm_irq_chips[i] = NULL;
+		}
+		kfree(prcm_irq_chips);
+		prcm_irq_chips = NULL;
+	}
+
+	kfree(prcm_irq_setup->saved_mask);
+	prcm_irq_setup->saved_mask = NULL;
+
+	kfree(prcm_irq_setup->priority_mask);
+	prcm_irq_setup->priority_mask = NULL;
+
+	irq_set_chained_handler(prcm_irq_setup->irq, NULL);
+
+	if (prcm_irq_setup->base_irq > 0)
+		irq_free_descs(prcm_irq_setup->base_irq,
+			prcm_irq_setup->nr_regs * 32);
+	prcm_irq_setup->base_irq = 0;
+}
+
+void omap_prcm_irq_prepare(void)
+{
+	prcm_irq_setup->suspended = true;
+}
+
+void omap_prcm_irq_complete(void)
+{
+	prcm_irq_setup->suspended = false;
+
+	/* If we have not saved the masks, do not attempt to restore */
+	if (!prcm_irq_setup->suspend_save_flag)
+		return;
+
+	prcm_irq_setup->suspend_save_flag = false;
+
+	/*
+	 * Re-enable all masked PRCM irq sources, this causes the PRCM
+	 * interrupt to fire immediately if the events were masked
+	 * previously in the chain handler
+	 */
+	prcm_irq_setup->restore_irqen(prcm_irq_setup->saved_mask);
+}
+
+/**
+ * omap_prcm_register_chain_handler - initializes the prcm chained interrupt
+ * handler based on provided parameters
+ * @irq_setup: hardware data about the underlying PRM/PRCM
+ *
+ * Set up the PRCM chained interrupt handler on the PRCM IRQ.  Sets up
+ * one generic IRQ chip per PRM interrupt status/enable register pair.
+ * Returns 0 upon success, -EINVAL if called twice or if invalid
+ * arguments are passed, or -ENOMEM on any other error.
+ */
+int omap_prcm_register_chain_handler(struct omap_prcm_irq_setup *irq_setup)
+{
+	int nr_regs = irq_setup->nr_regs;
+	u32 mask[OMAP_PRCM_MAX_NR_PENDING_REG];
+	int offset, i;
+	struct irq_chip_generic *gc;
+	struct irq_chip_type *ct;
+
+	if (!irq_setup)
+		return -EINVAL;
+
+	if (prcm_irq_setup) {
+		pr_err("PRCM: already initialized; won't reinitialize\n");
+		return -EINVAL;
+	}
+
+	if (nr_regs > OMAP_PRCM_MAX_NR_PENDING_REG) {
+		pr_err("PRCM: nr_regs too large\n");
+		return -EINVAL;
+	}
+
+	prcm_irq_setup = irq_setup;
+
+	prcm_irq_chips = kzalloc(sizeof(void *) * nr_regs, GFP_KERNEL);
+	prcm_irq_setup->saved_mask = kzalloc(sizeof(u32) * nr_regs, GFP_KERNEL);
+	prcm_irq_setup->priority_mask = kzalloc(sizeof(u32) * nr_regs,
+		GFP_KERNEL);
+
+	if (!prcm_irq_chips || !prcm_irq_setup->saved_mask ||
+	    !prcm_irq_setup->priority_mask) {
+		pr_err("PRCM: kzalloc failed\n");
+		goto err;
+	}
+
+	memset(mask, 0, sizeof(mask));
+
+	for (i = 0; i < irq_setup->nr_irqs; i++) {
+		offset = irq_setup->irqs[i].offset;
+		mask[offset >> 5] |= 1 << (offset & 0x1f);
+		if (irq_setup->irqs[i].priority)
+			irq_setup->priority_mask[offset >> 5] |=
+				1 << (offset & 0x1f);
+	}
+
+	irq_set_chained_handler(irq_setup->irq, omap_prcm_irq_handler);
+
+	irq_setup->base_irq = irq_alloc_descs(-1, 0, irq_setup->nr_regs * 32,
+		0);
+
+	if (irq_setup->base_irq < 0) {
+		pr_err("PRCM: failed to allocate irq descs: %d\n",
+			irq_setup->base_irq);
+		goto err;
+	}
+
+	for (i = 0; i <= irq_setup->nr_regs; i++) {
+		gc = irq_alloc_generic_chip("PRCM", 1,
+			irq_setup->base_irq + i * 32, prm_base,
+			handle_level_irq);
+
+		if (!gc) {
+			pr_err("PRCM: failed to allocate generic chip\n");
+			goto err;
+		}
+		ct = gc->chip_types;
+		ct->chip.irq_ack = irq_gc_ack_set_bit;
+		ct->chip.irq_mask = irq_gc_mask_clr_bit;
+		ct->chip.irq_unmask = irq_gc_mask_set_bit;
+
+		ct->regs.ack = irq_setup->ack + i * 4;
+		ct->regs.mask = irq_setup->mask + i * 4;
+
+		irq_setup_generic_chip(gc, mask[i], 0, IRQ_NOREQUEST, 0);
+		prcm_irq_chips[i] = gc;
+	}
+
+	return 0;
+
+err:
+	omap_prcm_irq_cleanup();
+	return -ENOMEM;
+}
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index d0f009cbfb5..247d89478f2 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -19,26 +19,21 @@
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/serial_reg.h>
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-#include <linux/serial_8250.h>
 #include <linux/pm_runtime.h>
 #include <linux/console.h>
 
-#ifdef CONFIG_SERIAL_OMAP
 #include <plat/omap-serial.h>
-#endif
-
 #include "common.h"
 #include <plat/board.h>
-#include <plat/clock.h>
 #include <plat/dma.h>
 #include <plat/omap_hwmod.h>
 #include <plat/omap_device.h>
+#include <plat/omap-pm.h>
 
 #include "prm2xxx_3xxx.h"
 #include "pm.h"
@@ -47,603 +42,226 @@
 #include "control.h"
 #include "mux.h"
 
-#define UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV	0x52
-#define UART_OMAP_WER		0x17	/* Wake-up enable register */
-
-#define UART_ERRATA_FIFO_FULL_ABORT	(0x1 << 0)
-#define UART_ERRATA_i202_MDR1_ACCESS	(0x1 << 1)
-
 /*
- * NOTE: By default the serial timeout is disabled as it causes lost characters
- * over the serial ports. This means that the UART clocks will stay on until
- * disabled via sysfs. This also causes that any deeper omap sleep states are
- * blocked. 
+ * NOTE: By default the serial auto_suspend timeout is disabled as it causes
+ * lost characters over the serial ports. This means that the UART clocks will
+ * stay on until power/autosuspend_delay is set for the uart from sysfs.
+ * This also causes that any deeper omap sleep states are blocked.
  */
-#define DEFAULT_TIMEOUT 0
+#define DEFAULT_AUTOSUSPEND_DELAY	-1
 
 #define MAX_UART_HWMOD_NAME_LEN		16
 
 struct omap_uart_state {
 	int num;
 	int can_sleep;
-	struct timer_list timer;
-	u32 timeout;
-
-	void __iomem *wk_st;
-	void __iomem *wk_en;
-	u32 wk_mask;
-	u32 padconf;
-	u32 dma_enabled;
-
-	struct clk *ick;
-	struct clk *fck;
-	int clocked;
-
-	int irq;
-	int regshift;
-	int irqflags;
-	void __iomem *membase;
-	resource_size_t mapbase;
 
 	struct list_head node;
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
-
-	u32 errata;
-#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
-	int context_valid;
-
-	/* Registers to be saved/restored for OFF-mode */
-	u16 dll;
-	u16 dlh;
-	u16 ier;
-	u16 sysc;
-	u16 scr;
-	u16 wer;
-	u16 mcr;
-#endif
 };
 
 static LIST_HEAD(uart_list);
 static u8 num_uarts;
+static u8 console_uart_id = -1;
+static u8 no_console_suspend;
+static u8 uart_debug;
+
+#define DEFAULT_RXDMA_POLLRATE		1	/* RX DMA polling rate (us) */
+#define DEFAULT_RXDMA_BUFSIZE		4096	/* RX DMA buffer size */
+#define DEFAULT_RXDMA_TIMEOUT		(3 * HZ)/* RX DMA timeout (jiffies) */
+
+static struct omap_uart_port_info omap_serial_default_info[] __initdata = {
+	{
+		.dma_enabled	= false,
+		.dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
+		.dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
+		.dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
+		.autosuspend_timeout = DEFAULT_AUTOSUSPEND_DELAY,
+	},
+};
 
-static inline unsigned int __serial_read_reg(struct uart_port *up,
-					     int offset)
-{
-	offset <<= up->regshift;
-	return (unsigned int)__raw_readb(up->membase + offset);
-}
-
-static inline unsigned int serial_read_reg(struct omap_uart_state *uart,
-					   int offset)
+#ifdef CONFIG_PM
+static void omap_uart_enable_wakeup(struct platform_device *pdev, bool enable)
 {
-	offset <<= uart->regshift;
-	return (unsigned int)__raw_readb(uart->membase + offset);
-}
+	struct omap_device *od = to_omap_device(pdev);
 
-static inline void __serial_write_reg(struct uart_port *up, int offset,
-		int value)
-{
-	offset <<= up->regshift;
-	__raw_writeb(value, up->membase + offset);
-}
+	if (!od)
+		return;
 
-static inline void serial_write_reg(struct omap_uart_state *uart, int offset,
-				    int value)
-{
-	offset <<= uart->regshift;
-	__raw_writeb(value, uart->membase + offset);
+	if (enable)
+		omap_hwmod_enable_wakeup(od->hwmods[0]);
+	else
+		omap_hwmod_disable_wakeup(od->hwmods[0]);
 }
 
 /*
- * Internal UARTs need to be initialized for the 8250 autoconfig to work
- * properly. Note that the TX watermark initialization may not be needed
- * once the 8250.c watermark handling code is merged.
+ * Errata i291: [UART]:Cannot Acknowledge Idle Requests
+ * in Smartidle Mode When Configured for DMA Operations.
+ * WA: configure uart in force idle mode.
  */
-
-static inline void __init omap_uart_reset(struct omap_uart_state *uart)
+static void omap_uart_set_noidle(struct platform_device *pdev)
 {
-	serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
-	serial_write_reg(uart, UART_OMAP_SCR, 0x08);
-	serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE);
-}
-
-#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
+	struct omap_device *od = to_omap_device(pdev);
 
-/*
- * Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6)
- * The access to uart register after MDR1 Access
- * causes UART to corrupt data.
- *
- * Need a delay =
- * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
- * give 10 times as much
- */
-static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val,
-		u8 fcr_val)
-{
-	u8 timeout = 255;
-
-	serial_write_reg(uart, UART_OMAP_MDR1, mdr1_val);
-	udelay(2);
-	serial_write_reg(uart, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT |
-			UART_FCR_CLEAR_RCVR);
-	/*
-	 * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
-	 * TX_FIFO_E bit is 1.
-	 */
-	while (UART_LSR_THRE != (serial_read_reg(uart, UART_LSR) &
-				(UART_LSR_THRE | UART_LSR_DR))) {
-		timeout--;
-		if (!timeout) {
-			/* Should *never* happen. we warn and carry on */
-			dev_crit(&uart->pdev->dev, "Errata i202: timedout %x\n",
-			serial_read_reg(uart, UART_LSR));
-			break;
-		}
-		udelay(1);
-	}
+	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
 }
 
-static void omap_uart_save_context(struct omap_uart_state *uart)
+static void omap_uart_set_forceidle(struct platform_device *pdev)
 {
-	u16 lcr = 0;
+	struct omap_device *od = to_omap_device(pdev);
 
-	if (!enable_off_mode)
-		return;
-
-	lcr = serial_read_reg(uart, UART_LCR);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	uart->dll = serial_read_reg(uart, UART_DLL);
-	uart->dlh = serial_read_reg(uart, UART_DLM);
-	serial_write_reg(uart, UART_LCR, lcr);
-	uart->ier = serial_read_reg(uart, UART_IER);
-	uart->sysc = serial_read_reg(uart, UART_OMAP_SYSC);
-	uart->scr = serial_read_reg(uart, UART_OMAP_SCR);
-	uart->wer = serial_read_reg(uart, UART_OMAP_WER);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_A);
-	uart->mcr = serial_read_reg(uart, UART_MCR);
-	serial_write_reg(uart, UART_LCR, lcr);
-
-	uart->context_valid = 1;
+	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_FORCE);
 }
 
-static void omap_uart_restore_context(struct omap_uart_state *uart)
-{
-	u16 efr = 0;
-
-	if (!enable_off_mode)
-		return;
-
-	if (!uart->context_valid)
-		return;
-
-	uart->context_valid = 0;
-
-	if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
-		omap_uart_mdr1_errataset(uart, UART_OMAP_MDR1_DISABLE, 0xA0);
-	else
-		serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
-
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	efr = serial_read_reg(uart, UART_EFR);
-	serial_write_reg(uart, UART_EFR, UART_EFR_ECB);
-	serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */
-	serial_write_reg(uart, UART_IER, 0x0);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_write_reg(uart, UART_DLL, uart->dll);
-	serial_write_reg(uart, UART_DLM, uart->dlh);
-	serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */
-	serial_write_reg(uart, UART_IER, uart->ier);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_A);
-	serial_write_reg(uart, UART_MCR, uart->mcr);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_write_reg(uart, UART_EFR, efr);
-	serial_write_reg(uart, UART_LCR, UART_LCR_WLEN8);
-	serial_write_reg(uart, UART_OMAP_SCR, uart->scr);
-	serial_write_reg(uart, UART_OMAP_WER, uart->wer);
-	serial_write_reg(uart, UART_OMAP_SYSC, uart->sysc);
-
-	if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
-		omap_uart_mdr1_errataset(uart, UART_OMAP_MDR1_16X_MODE, 0xA1);
-	else
-		/* UART 16x mode */
-		serial_write_reg(uart, UART_OMAP_MDR1,
-				UART_OMAP_MDR1_16X_MODE);
-}
 #else
-static inline void omap_uart_save_context(struct omap_uart_state *uart) {}
-static inline void omap_uart_restore_context(struct omap_uart_state *uart) {}
-#endif /* CONFIG_PM && CONFIG_ARCH_OMAP3 */
-
-static inline void omap_uart_enable_clocks(struct omap_uart_state *uart)
-{
-	if (uart->clocked)
-		return;
-
-	omap_device_enable(uart->pdev);
-	uart->clocked = 1;
-	omap_uart_restore_context(uart);
-}
-
-#ifdef CONFIG_PM
-
-static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
-{
-	if (!uart->clocked)
-		return;
-
-	omap_uart_save_context(uart);
-	uart->clocked = 0;
-	omap_device_idle(uart->pdev);
-}
-
-static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
-{
-	/* Set wake-enable bit */
-	if (uart->wk_en && uart->wk_mask) {
-		u32 v = __raw_readl(uart->wk_en);
-		v |= uart->wk_mask;
-		__raw_writel(v, uart->wk_en);
-	}
-
-	/* Ensure IOPAD wake-enables are set */
-	if (cpu_is_omap34xx() && uart->padconf) {
-		u16 v = omap_ctrl_readw(uart->padconf);
-		v |= OMAP3_PADCONF_WAKEUPENABLE0;
-		omap_ctrl_writew(v, uart->padconf);
-	}
-}
-
-static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
-{
-	/* Clear wake-enable bit */
-	if (uart->wk_en && uart->wk_mask) {
-		u32 v = __raw_readl(uart->wk_en);
-		v &= ~uart->wk_mask;
-		__raw_writel(v, uart->wk_en);
-	}
-
-	/* Ensure IOPAD wake-enables are cleared */
-	if (cpu_is_omap34xx() && uart->padconf) {
-		u16 v = omap_ctrl_readw(uart->padconf);
-		v &= ~OMAP3_PADCONF_WAKEUPENABLE0;
-		omap_ctrl_writew(v, uart->padconf);
-	}
-}
-
-static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
-					       int enable)
-{
-	u8 idlemode;
-
-	if (enable) {
-		/**
-		 * Errata 2.15: [UART]:Cannot Acknowledge Idle Requests
-		 * in Smartidle Mode When Configured for DMA Operations.
-		 */
-		if (uart->dma_enabled)
-			idlemode = HWMOD_IDLEMODE_FORCE;
-		else
-			idlemode = HWMOD_IDLEMODE_SMART;
-	} else {
-		idlemode = HWMOD_IDLEMODE_NO;
-	}
-
-	omap_hwmod_set_slave_idlemode(uart->oh, idlemode);
-}
-
-static void omap_uart_block_sleep(struct omap_uart_state *uart)
-{
-	omap_uart_enable_clocks(uart);
-
-	omap_uart_smart_idle_enable(uart, 0);
-	uart->can_sleep = 0;
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
-	else
-		del_timer(&uart->timer);
-}
-
-static void omap_uart_allow_sleep(struct omap_uart_state *uart)
-{
-	if (device_may_wakeup(&uart->pdev->dev))
-		omap_uart_enable_wakeup(uart);
-	else
-		omap_uart_disable_wakeup(uart);
-
-	if (!uart->clocked)
-		return;
-
-	omap_uart_smart_idle_enable(uart, 1);
-	uart->can_sleep = 1;
-	del_timer(&uart->timer);
-}
-
-static void omap_uart_idle_timer(unsigned long data)
-{
-	struct omap_uart_state *uart = (struct omap_uart_state *)data;
-
-	omap_uart_allow_sleep(uart);
-}
-
-void omap_uart_prepare_idle(int num)
-{
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		if (num == uart->num && uart->can_sleep) {
-			omap_uart_disable_clocks(uart);
-			return;
-		}
-	}
-}
-
-void omap_uart_resume_idle(int num)
-{
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		if (num == uart->num && uart->can_sleep) {
-			omap_uart_enable_clocks(uart);
-
-			/* Check for IO pad wakeup */
-			if (cpu_is_omap34xx() && uart->padconf) {
-				u16 p = omap_ctrl_readw(uart->padconf);
-
-				if (p & OMAP3_PADCONF_WAKEUPEVENT0)
-					omap_uart_block_sleep(uart);
-			}
-
-			/* Check for normal UART wakeup */
-			if (__raw_readl(uart->wk_st) & uart->wk_mask)
-				omap_uart_block_sleep(uart);
-			return;
-		}
-	}
-}
-
-void omap_uart_prepare_suspend(void)
-{
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		omap_uart_allow_sleep(uart);
-	}
-}
-
-int omap_uart_can_sleep(void)
-{
-	struct omap_uart_state *uart;
-	int can_sleep = 1;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		if (!uart->clocked)
-			continue;
-
-		if (!uart->can_sleep) {
-			can_sleep = 0;
-			continue;
-		}
-
-		/* This UART can now safely sleep. */
-		omap_uart_allow_sleep(uart);
-	}
-
-	return can_sleep;
-}
+static void omap_uart_enable_wakeup(struct platform_device *pdev, bool enable)
+{}
+static void omap_uart_set_noidle(struct platform_device *pdev) {}
+static void omap_uart_set_forceidle(struct platform_device *pdev) {}
+#endif /* CONFIG_PM */
 
-/**
- * omap_uart_interrupt()
- *
- * This handler is used only to detect that *any* UART interrupt has
- * occurred.  It does _nothing_ to handle the interrupt.  Rather,
- * any UART interrupt will trigger the inactivity timer so the
- * UART will not idle or sleep for its timeout period.
- *
- **/
-/* static int first_interrupt; */
-static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
-{
-	struct omap_uart_state *uart = dev_id;
+#ifdef CONFIG_OMAP_MUX
+static struct omap_device_pad default_uart1_pads[] __initdata = {
+	{
+		.name	= "uart1_cts.uart1_cts",
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart1_rts.uart1_rts",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart1_tx.uart1_tx",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart1_rx.uart1_rx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+		.idle	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+};
 
-	omap_uart_block_sleep(uart);
+static struct omap_device_pad default_uart2_pads[] __initdata = {
+	{
+		.name	= "uart2_cts.uart2_cts",
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart2_rts.uart2_rts",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart2_tx.uart2_tx",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart2_rx.uart2_rx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+		.idle	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+};
 
-	return IRQ_NONE;
-}
+static struct omap_device_pad default_uart3_pads[] __initdata = {
+	{
+		.name	= "uart3_cts_rctx.uart3_cts_rctx",
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart3_rts_sd.uart3_rts_sd",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart3_tx_irtx.uart3_tx_irtx",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart3_rx_irrx.uart3_rx_irrx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+		.idle	= OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+	},
+};
 
-static void omap_uart_idle_init(struct omap_uart_state *uart)
-{
-	int ret;
-
-	uart->can_sleep = 0;
-	uart->timeout = DEFAULT_TIMEOUT;
-	setup_timer(&uart->timer, omap_uart_idle_timer,
-		    (unsigned long) uart);
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
-	omap_uart_smart_idle_enable(uart, 0);
-
-	if (cpu_is_omap34xx() && !(cpu_is_ti81xx() || cpu_is_am33xx())) {
-		u32 mod = (uart->num > 1) ? OMAP3430_PER_MOD : CORE_MOD;
-		u32 wk_mask = 0;
-		u32 padconf = 0;
-
-		/* XXX These PRM accesses do not belong here */
-		uart->wk_en = OMAP34XX_PRM_REGADDR(mod, PM_WKEN1);
-		uart->wk_st = OMAP34XX_PRM_REGADDR(mod, PM_WKST1);
-		switch (uart->num) {
-		case 0:
-			wk_mask = OMAP3430_ST_UART1_MASK;
-			padconf = 0x182;
-			break;
-		case 1:
-			wk_mask = OMAP3430_ST_UART2_MASK;
-			padconf = 0x17a;
-			break;
-		case 2:
-			wk_mask = OMAP3430_ST_UART3_MASK;
-			padconf = 0x19e;
-			break;
-		case 3:
-			wk_mask = OMAP3630_ST_UART4_MASK;
-			padconf = 0x0d2;
-			break;
-		}
-		uart->wk_mask = wk_mask;
-		uart->padconf = padconf;
-	} else if (cpu_is_omap24xx()) {
-		u32 wk_mask = 0;
-		u32 wk_en = PM_WKEN1, wk_st = PM_WKST1;
-
-		switch (uart->num) {
-		case 0:
-			wk_mask = OMAP24XX_ST_UART1_MASK;
-			break;
-		case 1:
-			wk_mask = OMAP24XX_ST_UART2_MASK;
-			break;
-		case 2:
-			wk_en = OMAP24XX_PM_WKEN2;
-			wk_st = OMAP24XX_PM_WKST2;
-			wk_mask = OMAP24XX_ST_UART3_MASK;
-			break;
-		}
-		uart->wk_mask = wk_mask;
-		if (cpu_is_omap2430()) {
-			uart->wk_en = OMAP2430_PRM_REGADDR(CORE_MOD, wk_en);
-			uart->wk_st = OMAP2430_PRM_REGADDR(CORE_MOD, wk_st);
-		} else if (cpu_is_omap2420()) {
-			uart->wk_en = OMAP2420_PRM_REGADDR(CORE_MOD, wk_en);
-			uart->wk_st = OMAP2420_PRM_REGADDR(CORE_MOD, wk_st);
-		}
-	} else {
-		uart->wk_en = NULL;
-		uart->wk_st = NULL;
-		uart->wk_mask = 0;
-		uart->padconf = 0;
-	}
+static struct omap_device_pad default_omap36xx_uart4_pads[] __initdata = {
+	{
+		.name   = "gpmc_wait2.uart4_tx",
+		.enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "gpmc_wait3.uart4_rx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT | OMAP_MUX_MODE2,
+		.idle	= OMAP_PIN_INPUT | OMAP_MUX_MODE2,
+	},
+};
 
-	uart->irqflags |= IRQF_SHARED;
-	ret = request_threaded_irq(uart->irq, NULL, omap_uart_interrupt,
-				   IRQF_SHARED, "serial idle", (void *)uart);
-	WARN_ON(ret);
-}
+static struct omap_device_pad default_omap4_uart4_pads[] __initdata = {
+	{
+		.name	= "uart4_tx.uart4_tx",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart4_rx.uart4_rx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+		.idle	= OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+	},
+};
 
-void omap_uart_enable_irqs(int enable)
+static void omap_serial_fill_default_pads(struct omap_board_data *bdata)
 {
-	int ret;
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		if (enable) {
-			pm_runtime_put_sync(&uart->pdev->dev);
-			ret = request_threaded_irq(uart->irq, NULL,
-						   omap_uart_interrupt,
-						   IRQF_SHARED,
-						   "serial idle",
-						   (void *)uart);
-		} else {
-			pm_runtime_get_noresume(&uart->pdev->dev);
-			free_irq(uart->irq, (void *)uart);
+	switch (bdata->id) {
+	case 0:
+		bdata->pads = default_uart1_pads;
+		bdata->pads_cnt = ARRAY_SIZE(default_uart1_pads);
+		break;
+	case 1:
+		bdata->pads = default_uart2_pads;
+		bdata->pads_cnt = ARRAY_SIZE(default_uart2_pads);
+		break;
+	case 2:
+		bdata->pads = default_uart3_pads;
+		bdata->pads_cnt = ARRAY_SIZE(default_uart3_pads);
+		break;
+	case 3:
+		if (cpu_is_omap44xx()) {
+			bdata->pads = default_omap4_uart4_pads;
+			bdata->pads_cnt =
+				ARRAY_SIZE(default_omap4_uart4_pads);
+		} else if (cpu_is_omap3630()) {
+			bdata->pads = default_omap36xx_uart4_pads;
+			bdata->pads_cnt =
+				ARRAY_SIZE(default_omap36xx_uart4_pads);
 		}
+		break;
+	default:
+		break;
 	}
 }
-
-static ssize_t sleep_timeout_show(struct device *dev,
-				  struct device_attribute *attr,
-				  char *buf)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *odev = to_omap_device(pdev);
-	struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
-
-	return sprintf(buf, "%u\n", uart->timeout / HZ);
-}
-
-static ssize_t sleep_timeout_store(struct device *dev,
-				   struct device_attribute *attr,
-				   const char *buf, size_t n)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *odev = to_omap_device(pdev);
-	struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
-	unsigned int value;
-
-	if (sscanf(buf, "%u", &value) != 1) {
-		dev_err(dev, "sleep_timeout_store: Invalid value\n");
-		return -EINVAL;
-	}
-
-	uart->timeout = value * HZ;
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
-	else
-		/* A zero value means disable timeout feature */
-		omap_uart_block_sleep(uart);
-
-	return n;
-}
-
-static DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show,
-		sleep_timeout_store);
-#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
 #else
-static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
-static void omap_uart_block_sleep(struct omap_uart_state *uart)
-{
-	/* Needed to enable UART clocks when built without CONFIG_PM */
-	omap_uart_enable_clocks(uart);
-}
-#define DEV_CREATE_FILE(dev, attr)
-#endif /* CONFIG_PM */
-
-#ifndef CONFIG_SERIAL_OMAP
-/*
- * Override the default 8250 read handler: mem_serial_in()
- * Empty RX fifo read causes an abort on omap3630 and omap4
- * This function makes sure that an empty rx fifo is not read on these silicons
- * (OMAP1/2/3430 are not affected)
- */
-static unsigned int serial_in_override(struct uart_port *up, int offset)
-{
-	if (UART_RX == offset) {
-		unsigned int lsr;
-		lsr = __serial_read_reg(up, UART_LSR);
-		if (!(lsr & UART_LSR_DR))
-			return -EPERM;
-	}
-
-	return __serial_read_reg(up, offset);
-}
+static void omap_serial_fill_default_pads(struct omap_board_data *bdata) {}
+#endif
 
-static void serial_out_override(struct uart_port *up, int offset, int value)
+char *cmdline_find_option(char *str)
 {
-	unsigned int status, tmout = 10000;
+	extern char *saved_command_line;
 
-	status = __serial_read_reg(up, UART_LSR);
-	while (!(status & UART_LSR_THRE)) {
-		/* Wait up to 10ms for the character(s) to be sent. */
-		if (--tmout == 0)
-			break;
-		udelay(1);
-		status = __serial_read_reg(up, UART_LSR);
-	}
-	__serial_write_reg(up, offset, value);
+	return strstr(saved_command_line, str);
 }
-#endif
 
 static int __init omap_serial_early_init(void)
 {
-	int i = 0;
-
 	do {
 		char oh_name[MAX_UART_HWMOD_NAME_LEN];
 		struct omap_hwmod *oh;
 		struct omap_uart_state *uart;
+		char uart_name[MAX_UART_HWMOD_NAME_LEN];
 
 		snprintf(oh_name, MAX_UART_HWMOD_NAME_LEN,
-			 "uart%d", i + 1);
+			 "uart%d", num_uarts + 1);
 		oh = omap_hwmod_lookup(oh_name);
 		if (!oh)
 			break;
@@ -653,21 +271,35 @@ static int __init omap_serial_early_init(void)
 			return -ENODEV;
 
 		uart->oh = oh;
-		uart->num = i++;
+		uart->num = num_uarts++;
 		list_add_tail(&uart->node, &uart_list);
-		num_uarts++;
-
-		/*
-		 * NOTE: omap_hwmod_setup*() has not yet been called,
-		 *       so no hwmod functions will work yet.
-		 */
-
-		/*
-		 * During UART early init, device need to be probed
-		 * to determine SoC specific init before omap_device
-		 * is ready.  Therefore, don't allow idle here
-		 */
-		uart->oh->flags |= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET;
+		snprintf(uart_name, MAX_UART_HWMOD_NAME_LEN,
+				"%s%d", OMAP_SERIAL_NAME, uart->num);
+
+		if (cmdline_find_option(uart_name)) {
+			console_uart_id = uart->num;
+
+			if (console_loglevel >= 10) {
+				uart_debug = true;
+				pr_info("%s used as console in debug mode"
+						" uart%d clocks will not be"
+						" gated", uart_name, uart->num);
+			}
+
+			if (cmdline_find_option("no_console_suspend"))
+				no_console_suspend = true;
+
+			/*
+			 * omap-uart can be used for earlyprintk logs
+			 * So if omap-uart is used as console then prevent
+			 * uart reset and idle to get logs from omap-uart
+			 * until uart console driver is available to take
+			 * care for console messages.
+			 * Idling or resetting omap-uart while printing logs
+			 * early boot logs can stall the boot-up.
+			 */
+			oh->flags |= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET;
+		}
 	} while (1);
 
 	return 0;
@@ -677,6 +309,7 @@ core_initcall(omap_serial_early_init);
 /**
  * omap_serial_init_port() - initialize single serial port
  * @bdata: port specific board data pointer
+ * @info: platform specific data pointer
  *
  * This function initialies serial driver for given port only.
  * Platforms can call this function instead of omap_serial_init()
@@ -685,7 +318,8 @@ core_initcall(omap_serial_early_init);
  * Don't mix calls to omap_serial_init_port() and omap_serial_init(),
  * use only one of the two.
  */
-void __init omap_serial_init_port(struct omap_board_data *bdata)
+void __init omap_serial_init_port(struct omap_board_data *bdata,
+			struct omap_uart_port_info *info)
 {
 	struct omap_uart_state *uart;
 	struct omap_hwmod *oh;
@@ -693,15 +327,7 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	void *pdata = NULL;
 	u32 pdata_size = 0;
 	char *name;
-#ifndef CONFIG_SERIAL_OMAP
-	struct plat_serial8250_port ports[2] = {
-		{},
-		{.flags = 0},
-	};
-	struct plat_serial8250_port *p = &ports[0];
-#else
 	struct omap_uart_port_info omap_up;
-#endif
 
 	if (WARN_ON(!bdata))
 		return;
@@ -713,66 +339,34 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	list_for_each_entry(uart, &uart_list, node)
 		if (bdata->id == uart->num)
 			break;
+	if (!info)
+		info = omap_serial_default_info;
 
 	oh = uart->oh;
-	uart->dma_enabled = 0;
-#ifndef CONFIG_SERIAL_OMAP
-	name = "serial8250";
-
-	/*
-	 * !! 8250 driver does not use standard IORESOURCE* It
-	 * has it's own custom pdata that can be taken from
-	 * the hwmod resource data.  But, this needs to be
-	 * done after the build.
-	 *
-	 * ?? does it have to be done before the register ??
-	 * YES, because platform_device_data_add() copies
-	 * pdata, it does not use a pointer.
-	 */
-	p->flags = UPF_BOOT_AUTOCONF;
-	p->iotype = UPIO_MEM;
-	p->regshift = 2;
-	p->uartclk = OMAP24XX_BASE_BAUD * 16;
-	p->irq = oh->mpu_irqs[0].irq;
-	p->mapbase = oh->slaves[0]->addr->pa_start;
-	p->membase = omap_hwmod_get_mpu_rt_va(oh);
-	p->irqflags = IRQF_SHARED;
-	p->private_data = uart;
-
-	/*
-	 * omap44xx, ti816x: Never read empty UART fifo
-	 * omap3xxx: Never read empty UART fifo on UARTs
-	 * with IP rev >=0x52
-	 */
-	uart->regshift = p->regshift;
-	uart->membase = p->membase;
-	if (cpu_is_omap44xx() || cpu_is_ti81xx())
-		uart->errata |= UART_ERRATA_FIFO_FULL_ABORT;
-	else if ((serial_read_reg(uart, UART_OMAP_MVER) & 0xFF)
-			>= UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV)
-		uart->errata |= UART_ERRATA_FIFO_FULL_ABORT;
-
-	if (uart->errata & UART_ERRATA_FIFO_FULL_ABORT) {
-		p->serial_in = serial_in_override;
-		p->serial_out = serial_out_override;
-	}
-
-	pdata = &ports[0];
-	pdata_size = 2 * sizeof(struct plat_serial8250_port);
-#else
-
 	name = DRIVER_NAME;
 
-	omap_up.dma_enabled = uart->dma_enabled;
+	omap_up.dma_enabled = info->dma_enabled;
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
-	omap_up.mapbase = oh->slaves[0]->addr->pa_start;
-	omap_up.membase = omap_hwmod_get_mpu_rt_va(oh);
-	omap_up.irqflags = IRQF_SHARED;
-	omap_up.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+	omap_up.flags = UPF_BOOT_AUTOCONF;
+	omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
+	omap_up.set_forceidle = omap_uart_set_forceidle;
+	omap_up.set_noidle = omap_uart_set_noidle;
+	omap_up.enable_wakeup = omap_uart_enable_wakeup;
+	omap_up.dma_rx_buf_size = info->dma_rx_buf_size;
+	omap_up.dma_rx_timeout = info->dma_rx_timeout;
+	omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
+	omap_up.autosuspend_timeout = info->autosuspend_timeout;
+
+	/* Enable the MDR1 Errata i202 for OMAP2430/3xxx/44xx */
+	if (!cpu_is_omap2420() && !cpu_is_ti816x())
+		omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
+
+	/* Enable DMA Mode Force Idle Errata i291 for omap34xx/3630 */
+	if (cpu_is_omap34xx() || cpu_is_omap3630())
+		omap_up.errata |= UART_ERRATA_i291_DMA_FORCEIDLE;
 
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);
-#endif
 
 	if (WARN_ON(!oh))
 		return;
@@ -782,64 +376,29 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	WARN(IS_ERR(pdev), "Could not build omap_device for %s: %s.\n",
 	     name, oh->name);
 
-	omap_device_disable_idle_on_suspend(pdev);
+	if ((console_uart_id == bdata->id) && no_console_suspend)
+		omap_device_disable_idle_on_suspend(pdev);
+
 	oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt);
 
-	uart->irq = oh->mpu_irqs[0].irq;
-	uart->regshift = 2;
-	uart->mapbase = oh->slaves[0]->addr->pa_start;
-	uart->membase = omap_hwmod_get_mpu_rt_va(oh);
 	uart->pdev = pdev;
 
 	oh->dev_attr = uart;
 
-	console_lock(); /* in case the earlycon is on the UART */
-
-	/*
-	 * Because of early UART probing, UART did not get idled
-	 * on init.  Now that omap_device is ready, ensure full idle
-	 * before doing omap_device_enable().
-	 */
-	omap_hwmod_idle(uart->oh);
-
-	omap_device_enable(uart->pdev);
-	omap_uart_idle_init(uart);
-	omap_uart_reset(uart);
-	omap_hwmod_enable_wakeup(uart->oh);
-	omap_device_idle(uart->pdev);
-
-	/*
-	 * Need to block sleep long enough for interrupt driven
-	 * driver to start.  Console driver is in polling mode
-	 * so device needs to be kept enabled while polling driver
-	 * is in use.
-	 */
-	if (uart->timeout)
-		uart->timeout = (30 * HZ);
-	omap_uart_block_sleep(uart);
-	uart->timeout = DEFAULT_TIMEOUT;
-
-	console_unlock();
-
-	if ((cpu_is_omap34xx() && uart->padconf) ||
-	    (uart->wk_en && uart->wk_mask)) {
+	if (((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads)
+			&& !uart_debug)
 		device_init_wakeup(&pdev->dev, true);
-		DEV_CREATE_FILE(&pdev->dev, &dev_attr_sleep_timeout);
-	}
-
-	/* Enable the MDR1 errata for OMAP3 */
-	if (cpu_is_omap34xx() && !(cpu_is_ti81xx() || cpu_is_am33xx()))
-		uart->errata |= UART_ERRATA_i202_MDR1_ACCESS;
 }
 
 /**
- * omap_serial_init() - initialize all supported serial ports
+ * omap_serial_board_init() - initialize all supported serial ports
+ * @info: platform specific data pointer
  *
  * Initializes all available UARTs as serial ports. Platforms
  * can call this function when they want to have default behaviour
  * for serial ports (e.g initialize them all as serial ports).
  */
-void __init omap_serial_init(void)
+void __init omap_serial_board_init(struct omap_uart_port_info *info)
 {
 	struct omap_uart_state *uart;
 	struct omap_board_data bdata;
@@ -849,7 +408,25 @@ void __init omap_serial_init(void)
 		bdata.flags = 0;
 		bdata.pads = NULL;
 		bdata.pads_cnt = 0;
-		omap_serial_init_port(&bdata);
 
+		if (cpu_is_omap44xx() || cpu_is_omap34xx())
+			omap_serial_fill_default_pads(&bdata);
+
+		if (!info)
+			omap_serial_init_port(&bdata, NULL);
+		else
+			omap_serial_init_port(&bdata, &info[uart->num]);
 	}
 }
+
+/**
+ * omap_serial_init() - initialize all supported serial ports
+ *
+ * Initializes all available UARTs.
+ * Platforms can call this function when they want to have default behaviour
+ * for serial ports (e.g initialize them all as serial ports).
+ */
+void __init omap_serial_init(void)
+{
+	omap_serial_board_init(NULL);
+}
diff --git a/arch/arm/mach-omap2/sleep44xx.S b/arch/arm/mach-omap2/sleep44xx.S
new file mode 100644
index 00000000000..abd28340049
--- /dev/null
+++ b/arch/arm/mach-omap2/sleep44xx.S
@@ -0,0 +1,379 @@
+/*
+ * OMAP44xx sleep code.
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * 	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * This program is free software,you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/linkage.h>
+#include <asm/system.h>
+#include <asm/smp_scu.h>
+#include <asm/memory.h>
+#include <asm/hardware/cache-l2x0.h>
+
+#include <plat/omap44xx.h>
+#include <mach/omap-secure.h>
+
+#include "common.h"
+#include "omap4-sar-layout.h"
+
+#if defined(CONFIG_SMP) && defined(CONFIG_PM)
+
+.macro	DO_SMC
+	dsb
+	smc	#0
+	dsb
+.endm
+
+ppa_zero_params:
+	.word		0x0
+
+ppa_por_params:
+	.word		1, 0
+
+/*
+ * =============================
+ * == CPU suspend finisher ==
+ * =============================
+ *
+ * void omap4_finish_suspend(unsigned long cpu_state)
+ *
+ * This function code saves the CPU context and performs the CPU
+ * power down sequence. Calling WFI effectively changes the CPU
+ * power domains states to the desired target power state.
+ *
+ * @cpu_state : contains context save state (r0)
+ *	0 - No context lost
+ * 	1 - CPUx L1 and logic lost: MPUSS CSWR
+ * 	2 - CPUx L1 and logic lost + GIC lost: MPUSS OSWR
+ *	3 - CPUx L1 and logic lost + GIC + L2 lost: MPUSS OFF
+ * @return: This function never returns for CPU OFF and DORMANT power states.
+ * Post WFI, CPU transitions to DORMANT or OFF power state and on wake-up
+ * from this follows a full CPU reset path via ROM code to CPU restore code.
+ * The restore function pointer is stored at CPUx_WAKEUP_NS_PA_ADDR_OFFSET.
+ * It returns to the caller for CPU INACTIVE and ON power states or in case
+ * CPU failed to transition to targeted OFF/DORMANT state.
+ */
+ENTRY(omap4_finish_suspend)
+	stmfd	sp!, {lr}
+	cmp	r0, #0x0
+	beq	do_WFI				@ No lowpower state, jump to WFI
+
+	/*
+	 * Flush all data from the L1 data cache before disabling
+	 * SCTLR.C bit.
+	 */
+	bl	omap4_get_sar_ram_base
+	ldr	r9, [r0, #OMAP_TYPE_OFFSET]
+	cmp	r9, #0x1			@ Check for HS device
+	bne	skip_secure_l1_clean
+	mov	r0, #SCU_PM_NORMAL
+	mov	r1, #0xFF			@ clean seucre L1
+	stmfd   r13!, {r4-r12, r14}
+	ldr	r12, =OMAP4_MON_SCU_PWR_INDEX
+	DO_SMC
+	ldmfd   r13!, {r4-r12, r14}
+skip_secure_l1_clean:
+	bl	v7_flush_dcache_all
+
+	/*
+	 * Clear the SCTLR.C bit to prevent further data cache
+	 * allocation. Clearing SCTLR.C would make all the data accesses
+	 * strongly ordered and would not hit the cache.
+	 */
+	mrc	p15, 0, r0, c1, c0, 0
+	bic	r0, r0, #(1 << 2)		@ Disable the C bit
+	mcr	p15, 0, r0, c1, c0, 0
+	isb
+
+	/*
+	 * Invalidate L1 data cache. Even though only invalidate is
+	 * necessary exported flush API is used here. Doing clean
+	 * on already clean cache would be almost NOP.
+	 */
+	bl	v7_flush_dcache_all
+
+	/*
+	 * Switch the CPU from Symmetric Multiprocessing (SMP) mode
+	 * to AsymmetricMultiprocessing (AMP) mode by programming
+	 * the SCU power status to DORMANT or OFF mode.
+	 * This enables the CPU to be taken out of coherency by
+	 * preventing the CPU from receiving cache, TLB, or BTB
+	 * maintenance operations broadcast by other CPUs in the cluster.
+	 */
+	bl	omap4_get_sar_ram_base
+	mov	r8, r0
+	ldr	r9, [r8, #OMAP_TYPE_OFFSET]
+	cmp	r9, #0x1			@ Check for HS device
+	bne	scu_gp_set
+	mrc	p15, 0, r0, c0, c0, 5		@ Read MPIDR
+	ands	r0, r0, #0x0f
+	ldreq	r0, [r8, #SCU_OFFSET0]
+	ldrne	r0, [r8, #SCU_OFFSET1]
+	mov	r1, #0x00
+	stmfd   r13!, {r4-r12, r14}
+	ldr	r12, =OMAP4_MON_SCU_PWR_INDEX
+	DO_SMC
+	ldmfd   r13!, {r4-r12, r14}
+	b	skip_scu_gp_set
+scu_gp_set:
+	mrc	p15, 0, r0, c0, c0, 5		@ Read MPIDR
+	ands	r0, r0, #0x0f
+	ldreq	r1, [r8, #SCU_OFFSET0]
+	ldrne	r1, [r8, #SCU_OFFSET1]
+	bl	omap4_get_scu_base
+	bl	scu_power_mode
+skip_scu_gp_set:
+	mrc	p15, 0, r0, c1, c1, 2		@ Read NSACR data
+	tst	r0, #(1 << 18)
+	mrcne	p15, 0, r0, c1, c0, 1
+	bicne	r0, r0, #(1 << 6)		@ Disable SMP bit
+	mcrne	p15, 0, r0, c1, c0, 1
+	isb
+	dsb
+#ifdef CONFIG_CACHE_L2X0
+	/*
+	 * Clean and invalidate the L2 cache.
+	 * Common cache-l2x0.c functions can't be used here since it
+	 * uses spinlocks. We are out of coherency here with data cache
+	 * disabled. The spinlock implementation uses exclusive load/store
+	 * instruction which can fail without data cache being enabled.
+	 * OMAP4 hardware doesn't support exclusive monitor which can
+	 * overcome exclusive access issue. Because of this, CPU can
+	 * lead to deadlock.
+	 */
+	bl	omap4_get_sar_ram_base
+	mov	r8, r0
+	mrc	p15, 0, r5, c0, c0, 5		@ Read MPIDR
+	ands	r5, r5, #0x0f
+	ldreq	r0, [r8, #L2X0_SAVE_OFFSET0]	@ Retrieve L2 state from SAR
+	ldrne	r0, [r8, #L2X0_SAVE_OFFSET1]	@ memory.
+	cmp	r0, #3
+	bne	do_WFI
+#ifdef CONFIG_PL310_ERRATA_727915
+	mov	r0, #0x03
+	mov	r12, #OMAP4_MON_L2X0_DBG_CTRL_INDEX
+	DO_SMC
+#endif
+	bl	omap4_get_l2cache_base
+	mov	r2, r0
+	ldr	r0, =0xffff
+	str	r0, [r2, #L2X0_CLEAN_INV_WAY]
+wait:
+	ldr	r0, [r2, #L2X0_CLEAN_INV_WAY]
+	ldr	r1, =0xffff
+	ands	r0, r0, r1
+	bne	wait
+#ifdef CONFIG_PL310_ERRATA_727915
+	mov	r0, #0x00
+	mov	r12, #OMAP4_MON_L2X0_DBG_CTRL_INDEX
+	DO_SMC
+#endif
+l2x_sync:
+	bl	omap4_get_l2cache_base
+	mov	r2, r0
+	mov	r0, #0x0
+	str	r0, [r2, #L2X0_CACHE_SYNC]
+sync:
+	ldr	r0, [r2, #L2X0_CACHE_SYNC]
+	ands	r0, r0, #0x1
+	bne	sync
+#endif
+
+do_WFI:
+	bl	omap_do_wfi
+
+	/*
+	 * CPU is here when it failed to enter OFF/DORMANT or
+	 * no low power state was attempted.
+	 */
+	mrc	p15, 0, r0, c1, c0, 0
+	tst	r0, #(1 << 2)			@ Check C bit enabled?
+	orreq	r0, r0, #(1 << 2)		@ Enable the C bit
+	mcreq	p15, 0, r0, c1, c0, 0
+	isb
+
+	/*
+	 * Ensure the CPU power state is set to NORMAL in
+	 * SCU power state so that CPU is back in coherency.
+	 * In non-coherent mode CPU can lock-up and lead to
+	 * system deadlock.
+	 */
+	mrc	p15, 0, r0, c1, c0, 1
+	tst	r0, #(1 << 6)			@ Check SMP bit enabled?
+	orreq	r0, r0, #(1 << 6)
+	mcreq	p15, 0, r0, c1, c0, 1
+	isb
+	bl	omap4_get_sar_ram_base
+	mov	r8, r0
+	ldr	r9, [r8, #OMAP_TYPE_OFFSET]
+	cmp	r9, #0x1			@ Check for HS device
+	bne	scu_gp_clear
+	mov	r0, #SCU_PM_NORMAL
+	mov	r1, #0x00
+	stmfd   r13!, {r4-r12, r14}
+	ldr	r12, =OMAP4_MON_SCU_PWR_INDEX
+	DO_SMC
+	ldmfd   r13!, {r4-r12, r14}
+	b	skip_scu_gp_clear
+scu_gp_clear:
+	bl	omap4_get_scu_base
+	mov	r1, #SCU_PM_NORMAL
+	bl	scu_power_mode
+skip_scu_gp_clear:
+	isb
+	dsb
+	ldmfd	sp!, {pc}
+ENDPROC(omap4_finish_suspend)
+
+/*
+ * ============================
+ * == CPU resume entry point ==
+ * ============================
+ *
+ * void omap4_cpu_resume(void)
+ *
+ * ROM code jumps to this function while waking up from CPU
+ * OFF or DORMANT state. Physical address of the function is
+ * stored in the SAR RAM while entering to OFF or DORMANT mode.
+ * The restore function pointer is stored at CPUx_WAKEUP_NS_PA_ADDR_OFFSET.
+ */
+ENTRY(omap4_cpu_resume)
+	/*
+	 * Configure ACTRL and enable NS SMP bit access on CPU1 on HS device.
+	 * OMAP44XX EMU/HS devices - CPU0 SMP bit access is enabled in PPA
+	 * init and for CPU1, a secure PPA API provided. CPU0 must be ON
+	 * while executing NS_SMP API on CPU1 and PPA version must be 1.4.0+.
+	 * OMAP443X GP devices- SMP bit isn't accessible.
+	 * OMAP446X GP devices - SMP bit access is enabled on both CPUs.
+	 */
+	ldr	r8, =OMAP44XX_SAR_RAM_BASE
+	ldr	r9, [r8, #OMAP_TYPE_OFFSET]
+	cmp	r9, #0x1			@ Skip if GP device
+	bne	skip_ns_smp_enable
+	mrc     p15, 0, r0, c0, c0, 5
+	ands    r0, r0, #0x0f
+	beq	skip_ns_smp_enable
+ppa_actrl_retry:
+	mov     r0, #OMAP4_PPA_CPU_ACTRL_SMP_INDEX
+	adr	r3, ppa_zero_params		@ Pointer to parameters
+	mov	r1, #0x0			@ Process ID
+	mov	r2, #0x4			@ Flag
+	mov	r6, #0xff
+	mov	r12, #0x00			@ Secure Service ID
+	DO_SMC
+	cmp	r0, #0x0			@ API returns 0 on success.
+	beq	enable_smp_bit
+	b	ppa_actrl_retry
+enable_smp_bit:
+	mrc	p15, 0, r0, c1, c0, 1
+	tst	r0, #(1 << 6)			@ Check SMP bit enabled?
+	orreq	r0, r0, #(1 << 6)
+	mcreq	p15, 0, r0, c1, c0, 1
+	isb
+skip_ns_smp_enable:
+#ifdef CONFIG_CACHE_L2X0
+	/*
+	 * Restore the L2 AUXCTRL and enable the L2 cache.
+	 * OMAP4_MON_L2X0_AUXCTRL_INDEX =  Program the L2X0 AUXCTRL
+	 * OMAP4_MON_L2X0_CTRL_INDEX =  Enable the L2 using L2X0 CTRL
+	 * register r0 contains value to be programmed.
+	 * L2 cache is already invalidate by ROM code as part
+	 * of MPUSS OFF wakeup path.
+	 */
+	ldr	r2, =OMAP44XX_L2CACHE_BASE
+	ldr	r0, [r2, #L2X0_CTRL]
+	and	r0, #0x0f
+	cmp	r0, #1
+	beq	skip_l2en			@ Skip if already enabled
+	ldr	r3, =OMAP44XX_SAR_RAM_BASE
+	ldr	r1, [r3, #OMAP_TYPE_OFFSET]
+	cmp	r1, #0x1			@ Check for HS device
+	bne     set_gp_por
+	ldr     r0, =OMAP4_PPA_L2_POR_INDEX
+	ldr     r1, =OMAP44XX_SAR_RAM_BASE
+	ldr     r4, [r1, #L2X0_PREFETCH_CTRL_OFFSET]
+	adr     r3, ppa_por_params
+	str     r4, [r3, #0x04]
+	mov	r1, #0x0			@ Process ID
+	mov	r2, #0x4			@ Flag
+	mov	r6, #0xff
+	mov	r12, #0x00			@ Secure Service ID
+	DO_SMC
+	b	set_aux_ctrl
+set_gp_por:
+	ldr     r1, =OMAP44XX_SAR_RAM_BASE
+	ldr     r0, [r1, #L2X0_PREFETCH_CTRL_OFFSET]
+	ldr	r12, =OMAP4_MON_L2X0_PREFETCH_INDEX	@ Setup L2 PREFETCH
+	DO_SMC
+set_aux_ctrl:
+	ldr     r1, =OMAP44XX_SAR_RAM_BASE
+	ldr	r0, [r1, #L2X0_AUXCTRL_OFFSET]
+	ldr	r12, =OMAP4_MON_L2X0_AUXCTRL_INDEX	@ Setup L2 AUXCTRL
+	DO_SMC
+	mov	r0, #0x1
+	ldr	r12, =OMAP4_MON_L2X0_CTRL_INDEX		@ Enable L2 cache
+	DO_SMC
+skip_l2en:
+#endif
+
+	b	cpu_resume			@ Jump to generic resume
+ENDPROC(omap4_cpu_resume)
+#endif
+
+#ifndef CONFIG_OMAP4_ERRATA_I688
+ENTRY(omap_bus_sync)
+	mov	pc, lr
+ENDPROC(omap_bus_sync)
+#endif
+
+ENTRY(omap_do_wfi)
+	stmfd	sp!, {lr}
+	/* Drain interconnect write buffers. */
+	bl omap_bus_sync
+
+	/*
+	 * Execute an ISB instruction to ensure that all of the
+	 * CP15 register changes have been committed.
+	 */
+	isb
+
+	/*
+	 * Execute a barrier instruction to ensure that all cache,
+	 * TLB and branch predictor maintenance operations issued
+	 * by any CPU in the cluster have completed.
+	 */
+	dsb
+	dmb
+
+	/*
+	 * Execute a WFI instruction and wait until the
+	 * STANDBYWFI output is asserted to indicate that the
+	 * CPU is in idle and low power state. CPU can specualatively
+	 * prefetch the instructions so add NOPs after WFI. Sixteen
+	 * NOPs as per Cortex-A9 pipeline.
+	 */
+	wfi					@ Wait For Interrupt
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+
+	ldmfd	sp!, {pc}
+ENDPROC(omap_do_wfi)
diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h
index 83cca9bcfc9..1bf0df81bdc 100644
--- a/arch/arm/plat-mxc/include/mach/common.h
+++ b/arch/arm/plat-mxc/include/mach/common.h
@@ -131,6 +131,12 @@ extern void imx53_evk_common_init(void);
 extern void imx53_qsb_common_init(void);
 extern void imx53_smd_common_init(void);
 extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
-extern void imx6q_pm_init(void);
 extern void imx6q_clock_map_io(void);
+
+#ifdef CONFIG_PM
+extern void imx6q_pm_init(void);
+#else
+static inline void imx6q_pm_init(void) {}
+#endif
+
 #endif
diff --git a/arch/arm/plat-mxc/include/mach/mxc.h b/arch/arm/plat-mxc/include/mach/mxc.h
index a4d36d601d5..d78298366a9 100644
--- a/arch/arm/plat-mxc/include/mach/mxc.h
+++ b/arch/arm/plat-mxc/include/mach/mxc.h
@@ -168,7 +168,7 @@ struct cpu_op {
 	u32 cpu_rate;
 };
 
-int tzic_enable_wake(int is_idle);
+int tzic_enable_wake(void);
 
 extern struct cpu_op *(*get_cpu_op)(int *op);
 #endif
diff --git a/arch/arm/plat-mxc/tzic.c b/arch/arm/plat-mxc/tzic.c
index a3c164c7ba8..98308ec1f32 100644
--- a/arch/arm/plat-mxc/tzic.c
+++ b/arch/arm/plat-mxc/tzic.c
@@ -73,7 +73,28 @@ static int tzic_set_irq_fiq(unsigned int irq, unsigned int type)
 #define tzic_set_irq_fiq NULL
 #endif
 
-static unsigned int *wakeup_intr[4];
+#ifdef CONFIG_PM
+static void tzic_irq_suspend(struct irq_data *d)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	int idx = gc->irq_base >> 5;
+
+	__raw_writel(gc->wake_active, tzic_base + TZIC_WAKEUP0(idx));
+}
+
+static void tzic_irq_resume(struct irq_data *d)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	int idx = gc->irq_base >> 5;
+
+	__raw_writel(__raw_readl(tzic_base + TZIC_ENSET0(idx)),
+		     tzic_base + TZIC_WAKEUP0(idx));
+}
+
+#else
+#define tzic_irq_suspend NULL
+#define tzic_irq_resume NULL
+#endif
 
 static struct mxc_extra_irq tzic_extra_irq = {
 #ifdef CONFIG_FIQ
@@ -91,12 +112,13 @@ static __init void tzic_init_gc(unsigned int irq_start)
 				    handle_level_irq);
 	gc->private = &tzic_extra_irq;
 	gc->wake_enabled = IRQ_MSK(32);
-	wakeup_intr[idx] = &gc->wake_active;
 
 	ct = gc->chip_types;
 	ct->chip.irq_mask = irq_gc_mask_disable_reg;
 	ct->chip.irq_unmask = irq_gc_unmask_enable_reg;
 	ct->chip.irq_set_wake = irq_gc_set_wake;
+	ct->chip.irq_suspend = tzic_irq_suspend;
+	ct->chip.irq_resume = tzic_irq_resume;
 	ct->regs.disable = TZIC_ENCLEAR0(idx);
 	ct->regs.enable = TZIC_ENSET0(idx);
 
@@ -167,23 +189,19 @@ void __init tzic_init_irq(void __iomem *irqbase)
 /**
  * tzic_enable_wake() - enable wakeup interrupt
  *
- * @param is_idle		1 if called in idle loop (ENSET0 register);
- *				0 to be used when called from low power entry
  * @return			0 if successful; non-zero otherwise
  */
-int tzic_enable_wake(int is_idle)
+int tzic_enable_wake(void)
 {
-	unsigned int i, v;
+	unsigned int i;
 
 	__raw_writel(1, tzic_base + TZIC_DSMINT);
 	if (unlikely(__raw_readl(tzic_base + TZIC_DSMINT) == 0))
 		return -EAGAIN;
 
-	for (i = 0; i < 4; i++) {
-		v = is_idle ? __raw_readl(tzic_base + TZIC_ENSET0(i)) :
-			*wakeup_intr[i];
-		__raw_writel(v, tzic_base + TZIC_WAKEUP0(i));
-	}
+	for (i = 0; i < 4; i++)
+		__raw_writel(__raw_readl(tzic_base + TZIC_ENSET0(i)),
+			     tzic_base + TZIC_WAKEUP0(i));
 
 	return 0;
 }
diff --git a/arch/arm/plat-omap/common.c b/arch/arm/plat-omap/common.c
index 2ee6341fffd..06383b51e65 100644
--- a/arch/arm/plat-omap/common.c
+++ b/arch/arm/plat-omap/common.c
@@ -22,6 +22,8 @@
 #include <plat/vram.h>
 #include <plat/dsp.h>
 
+#include <plat/omap-secure.h>
+
 
 #define NO_LENGTH_CHECK 0xffffffff
 
@@ -66,6 +68,7 @@ void __init omap_reserve(void)
 	omapfb_reserve_sdram_memblock();
 	omap_vram_reserve_sdram_memblock();
 	omap_dsp_reserve_sdram_memblock();
+	omap_secure_ram_reserve_memblock();
 }
 
 void __init omap_init_consistent_dma_size(void)
diff --git a/arch/arm/plat-omap/include/plat/omap-secure.h b/arch/arm/plat-omap/include/plat/omap-secure.h
new file mode 100644
index 00000000000..64f9d1c7f1b
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/omap-secure.h
@@ -0,0 +1,13 @@
+#ifndef __OMAP_SECURE_H__
+#define __OMAP_SECURE_H__
+
+#include <linux/types.h>
+
+#ifdef CONFIG_ARCH_OMAP2PLUS
+extern int omap_secure_ram_reserve_memblock(void);
+#else
+static inline void omap_secure_ram_reserve_memblock(void)
+{ }
+#endif
+
+#endif /* __OMAP_SECURE_H__ */
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
index 2682043f5a5..9ff444469f3 100644
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -19,6 +19,7 @@
 
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
+#include <linux/pm_qos.h>
 
 #include <plat/mux.h>
 
@@ -33,6 +34,8 @@
 
 #define OMAP_MODE13X_SPEED	230400
 
+#define OMAP_UART_SCR_TX_EMPTY	0x08
+
 /* WER = 0x7F
  * Enable module level wakeup in WER reg
  */
@@ -51,18 +54,27 @@
 
 #define OMAP_UART_DMA_CH_FREE	-1
 
-#define RX_TIMEOUT		(3 * HZ)
 #define OMAP_MAX_HSUART_PORTS	4
 
 #define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA
 
+#define UART_ERRATA_i202_MDR1_ACCESS	BIT(0)
+#define UART_ERRATA_i291_DMA_FORCEIDLE	BIT(1)
+
 struct omap_uart_port_info {
 	bool			dma_enabled;	/* To specify DMA Mode */
 	unsigned int		uartclk;	/* UART clock rate */
-	void __iomem		*membase;	/* ioremap cookie or NULL */
-	resource_size_t		mapbase;	/* resource base */
-	unsigned long		irqflags;	/* request_irq flags */
 	upf_t			flags;		/* UPF_* flags */
+	u32			errata;
+	unsigned int		dma_rx_buf_size;
+	unsigned int		dma_rx_timeout;
+	unsigned int		autosuspend_timeout;
+	unsigned int		dma_rx_poll_rate;
+
+	int (*get_context_loss_count)(struct device *);
+	void (*set_forceidle)(struct platform_device *);
+	void (*set_noidle)(struct platform_device *);
+	void (*enable_wakeup)(struct platform_device *, bool);
 };
 
 struct uart_omap_dma {
@@ -86,8 +98,9 @@ struct uart_omap_dma {
 	spinlock_t		rx_lock;
 	/* timer to poll activity on rx dma */
 	struct timer_list	rx_timer;
-	int			rx_buf_size;
-	int			rx_timeout;
+	unsigned int		rx_buf_size;
+	unsigned int		rx_poll_rate;
+	unsigned int		rx_timeout;
 };
 
 struct uart_omap_port {
@@ -100,6 +113,10 @@ struct uart_omap_port {
 	unsigned char		mcr;
 	unsigned char		fcr;
 	unsigned char		efr;
+	unsigned char		dll;
+	unsigned char		dlh;
+	unsigned char		mdr1;
+	unsigned char		scr;
 
 	int			use_dma;
 	/*
@@ -111,6 +128,14 @@ struct uart_omap_port {
 	unsigned char		msr_saved_flags;
 	char			name[20];
 	unsigned long		port_activity;
+	u32			context_loss_cnt;
+	u32			errata;
+	u8			wakeups_enabled;
+
+	struct pm_qos_request	pm_qos_request;
+	u32			latency;
+	u32			calc_latency;
+	struct work_struct	qos_work;
 };
 
 #endif /* __OMAP_SERIAL_H__ */
diff --git a/arch/arm/plat-omap/include/plat/omap44xx.h b/arch/arm/plat-omap/include/plat/omap44xx.h
index ea2b8a6306e..c0d478e55c8 100644
--- a/arch/arm/plat-omap/include/plat/omap44xx.h
+++ b/arch/arm/plat-omap/include/plat/omap44xx.h
@@ -45,6 +45,7 @@
 #define OMAP44XX_WKUPGEN_BASE		0x48281000
 #define OMAP44XX_MCPDM_BASE		0x40132000
 #define OMAP44XX_MCPDM_L3_BASE		0x49032000
+#define OMAP44XX_SAR_RAM_BASE		0x4a326000
 
 #define OMAP44XX_MAILBOX_BASE		(L4_44XX_BASE + 0xF4000)
 #define OMAP44XX_HSUSB_OTG_BASE		(L4_44XX_BASE + 0xAB000)
diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h
index 8b372ede17c..647010109af 100644
--- a/arch/arm/plat-omap/include/plat/omap_hwmod.h
+++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h
@@ -97,6 +97,7 @@ struct omap_hwmod_mux_info {
 	struct omap_device_pad		*pads;
 	int				nr_pads_dynamic;
 	struct omap_device_pad		**pads_dynamic;
+	int				*irqs;
 	bool				enabled;
 };
 
@@ -416,10 +417,13 @@ struct omap_hwmod_omap4_prcm {
  * _HWMOD_NO_MPU_PORT: no path exists for the MPU to write to this module
  * _HWMOD_WAKEUP_ENABLED: set when the omap_hwmod code has enabled ENAWAKEUP
  * _HWMOD_SYSCONFIG_LOADED: set when the OCP_SYSCONFIG value has been cached
+ * _HWMOD_SKIP_ENABLE: set if hwmod enabled during init (HWMOD_INIT_NO_IDLE) -
+ *     causes the first call to _enable() to only update the pinmux
  */
 #define _HWMOD_NO_MPU_PORT			(1 << 0)
 #define _HWMOD_WAKEUP_ENABLED			(1 << 1)
 #define _HWMOD_SYSCONFIG_LOADED			(1 << 2)
+#define _HWMOD_SKIP_ENABLE			(1 << 3)
 
 /*
  * omap_hwmod._state definitions
@@ -604,6 +608,8 @@ int omap_hwmod_get_context_loss_count(struct omap_hwmod *oh);
 
 int omap_hwmod_no_setup_reset(struct omap_hwmod *oh);
 
+int omap_hwmod_pad_route_irq(struct omap_hwmod *oh, int pad_idx, int irq_idx);
+
 /*
  * Chip variant-specific hwmod init routines - XXX should be converted
  * to use initcalls once the initial boot ordering is straightened out
diff --git a/arch/arm/plat-omap/include/plat/serial.h b/arch/arm/plat-omap/include/plat/serial.h
index 80b6d39c31e..198d1e6a4a6 100644
--- a/arch/arm/plat-omap/include/plat/serial.h
+++ b/arch/arm/plat-omap/include/plat/serial.h
@@ -107,15 +107,13 @@
 #ifndef __ASSEMBLER__
 
 struct omap_board_data;
+struct omap_uart_port_info;
 
 extern void omap_serial_init(void);
-extern void omap_serial_init_port(struct omap_board_data *bdata);
 extern int omap_uart_can_sleep(void);
-extern void omap_uart_check_wakeup(void);
-extern void omap_uart_prepare_suspend(void);
-extern void omap_uart_prepare_idle(int num);
-extern void omap_uart_resume_idle(int num);
-extern void omap_uart_enable_irqs(int enable);
+extern void omap_serial_board_init(struct omap_uart_port_info *platform_data);
+extern void omap_serial_init_port(struct omap_board_data *bdata,
+		struct omap_uart_port_info *platform_data);
 #endif
 
 #endif
diff --git a/arch/arm/plat-omap/include/plat/sram.h b/arch/arm/plat-omap/include/plat/sram.h
index f500fc34d06..75aa1b2bef5 100644
--- a/arch/arm/plat-omap/include/plat/sram.h
+++ b/arch/arm/plat-omap/include/plat/sram.h
@@ -95,6 +95,10 @@ static inline void omap_push_sram_idle(void) {}
  */
 #define OMAP2_SRAM_PA		0x40200000
 #define OMAP3_SRAM_PA           0x40200000
+#ifdef CONFIG_OMAP4_ERRATA_I688
+#define OMAP4_SRAM_PA		0x40304000
+#define OMAP4_SRAM_VA		0xfe404000
+#else
 #define OMAP4_SRAM_PA		0x40300000
-
+#endif
 #endif
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 6b058a621e8..4243bdcc87b 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -40,7 +40,11 @@
 #define OMAP1_SRAM_PA		0x20000000
 #define OMAP2_SRAM_PUB_PA	(OMAP2_SRAM_PA + 0xf800)
 #define OMAP3_SRAM_PUB_PA       (OMAP3_SRAM_PA + 0x8000)
+#ifdef CONFIG_OMAP4_ERRATA_I688
+#define OMAP4_SRAM_PUB_PA	OMAP4_SRAM_PA
+#else
 #define OMAP4_SRAM_PUB_PA	(OMAP4_SRAM_PA + 0x4000)
+#endif
 
 #if defined(CONFIG_ARCH_OMAP2PLUS)
 #define SRAM_BOOTLOADER_SZ	0x00
@@ -161,6 +165,10 @@ static void __init omap_map_sram(void)
 	if (omap_sram_size == 0)
 		return;
 
+#ifdef CONFIG_OMAP4_ERRATA_I688
+		omap_sram_start += PAGE_SIZE;
+		omap_sram_size -= SZ_16K;
+#endif
 	if (cpu_is_omap34xx()) {
 		/*
 		 * SRAM must be marked as non-cached on OMAP3 since the