ARM: pxa: Update Balloon3 for new FPGA firmware

The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

2 files changed, 31 insertions, 22 deletions

diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c
index adb8e9f355d..d4649c0e23f 100644
--- a/arch/arm/mach-pxa/balloon3.c
+++ b/arch/arm/mach-pxa/balloon3.c
@@ -567,27 +567,29 @@ static inline void balloon3_i2c_init(void) {}
  * NAND
  ******************************************************************************/
 #if defined(CONFIG_MTD_NAND_PLATFORM)||defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
-static uint16_t balloon3_ctl =
-	BALLOON3_NAND_CONTROL_FLCE0 | BALLOON3_NAND_CONTROL_FLCE1 |
-	BALLOON3_NAND_CONTROL_FLCE2 | BALLOON3_NAND_CONTROL_FLCE3 |
-	BALLOON3_NAND_CONTROL_FLWP;
-
 static void balloon3_nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 {
 	struct nand_chip *this = mtd->priv;
+	uint8_t balloon3_ctl_set = 0, balloon3_ctl_clr = 0;
 
 	if (ctrl & NAND_CTRL_CHANGE) {
 		if (ctrl & NAND_CLE)
-			balloon3_ctl |= BALLOON3_NAND_CONTROL_FLCLE;
+			balloon3_ctl_set |= BALLOON3_NAND_CONTROL_FLCLE;
 		else
-			balloon3_ctl &= ~BALLOON3_NAND_CONTROL_FLCLE;
+			balloon3_ctl_clr |= BALLOON3_NAND_CONTROL_FLCLE;
 
 		if (ctrl & NAND_ALE)
-			balloon3_ctl |= BALLOON3_NAND_CONTROL_FLALE;
+			balloon3_ctl_set |= BALLOON3_NAND_CONTROL_FLALE;
 		else
-			balloon3_ctl &= ~BALLOON3_NAND_CONTROL_FLALE;
-
-		__raw_writel(balloon3_ctl, BALLOON3_NAND_CONTROL_REG);
+			balloon3_ctl_clr |= BALLOON3_NAND_CONTROL_FLALE;
+
+		if (balloon3_ctl_clr)
+			__raw_writel(balloon3_ctl_clr,
+				BALLOON3_NAND_CONTROL_REG);
+		if (balloon3_ctl_set)
+			__raw_writel(balloon3_ctl_set,
+				BALLOON3_NAND_CONTROL_REG |
+				BALLOON3_FPGA_SETnCLR);
 	}
 
 	if (cmd != NAND_CMD_NONE)
@@ -599,15 +601,15 @@ static void balloon3_nand_select_chip(struct mtd_info *mtd, int chip)
 	if (chip < 0 || chip > 3)
 		return;
 
-	balloon3_ctl |= BALLOON3_NAND_CONTROL_FLCE0 |
-			BALLOON3_NAND_CONTROL_FLCE1 |
-			BALLOON3_NAND_CONTROL_FLCE2 |
-			BALLOON3_NAND_CONTROL_FLCE3;
+	/* Assert all nCE lines */
+	__raw_writew(
+		BALLOON3_NAND_CONTROL_FLCE0 | BALLOON3_NAND_CONTROL_FLCE1 |
+		BALLOON3_NAND_CONTROL_FLCE2 | BALLOON3_NAND_CONTROL_FLCE3,
+		BALLOON3_NAND_CONTROL_REG | BALLOON3_FPGA_SETnCLR);
 
 	/* Deassert correct nCE line */
-	balloon3_ctl &= ~(BALLOON3_NAND_CONTROL_FLCE0 << chip);
-
-	__raw_writew(balloon3_ctl, BALLOON3_NAND_CONTROL_REG);
+	__raw_writew(BALLOON3_NAND_CONTROL_FLCE0 << chip,
+		BALLOON3_NAND_CONTROL_REG);
 }
 
 static int balloon3_nand_probe(struct platform_device *pdev)
@@ -616,11 +618,12 @@ static int balloon3_nand_probe(struct platform_device *pdev)
 	uint16_t ver;
 	int ret;
 
-	__raw_writew(BALLOON3_NAND_CONTROL2_16BIT, BALLOON3_NAND_CONTROL2_REG);
+	__raw_writew(BALLOON3_NAND_CONTROL2_16BIT,
+		BALLOON3_NAND_CONTROL2_REG | BALLOON3_FPGA_SETnCLR);
 
 	ver = __raw_readw(BALLOON3_FPGA_VER);
-	if (ver > 0x0201)
-		pr_warn("The FPGA code, version 0x%04x, is newer than rel-0.3. "
+	if (ver < 0x4f08)
+		pr_warn("The FPGA code, version 0x%04x, is too old. "
 			"NAND support might be broken in this version!", ver);
 
 	/* Power up the NAND chips */
@@ -635,7 +638,11 @@ static int balloon3_nand_probe(struct platform_device *pdev)
 	gpio_set_value(BALLOON3_GPIO_RUN_NAND, 1);
 
 	/* Deassert all nCE lines and write protect line */
-	__raw_writel(balloon3_ctl, BALLOON3_NAND_CONTROL_REG);
+	__raw_writel(
+		BALLOON3_NAND_CONTROL_FLCE0 | BALLOON3_NAND_CONTROL_FLCE1 |
+		BALLOON3_NAND_CONTROL_FLCE2 | BALLOON3_NAND_CONTROL_FLCE3 |
+		BALLOON3_NAND_CONTROL_FLWP,
+		BALLOON3_NAND_CONTROL_REG | BALLOON3_FPGA_SETnCLR);
 	return 0;
 
 err2:
diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/include/mach/balloon3.h
index 3506da1f27b..f6c81ea5148 100644
--- a/arch/arm/mach-pxa/include/mach/balloon3.h
+++ b/arch/arm/mach-pxa/include/mach/balloon3.h
@@ -26,6 +26,8 @@ enum balloon3_features {
 #define BALLOON3_FPGA_VIRT	(0xf1000000)	/* as per balloon2 */
 #define BALLOON3_FPGA_LENGTH	0x01000000
 
+#define	BALLOON3_FPGA_SETnCLR		(0x1000)
+
 /* FPGA / CPLD registers for CF socket */
 #define	BALLOON3_CF_STATUS_REG		(BALLOON3_FPGA_VIRT + 0x00e00008)
 #define	BALLOON3_CF_CONTROL_REG		(BALLOON3_FPGA_VIRT + 0x00e00008)